Society Of Mechatronics Engineering & Technology "SOME ...



TOS CNC BORING MACHINEMachine Description:TOS CNC BORING MACHINE is manufactures by TOS VARNSDORF . This Horizontal Boring machine is crosswise design machine with Live Spindle movable column and with movable Rotary table. WHN/WHQ 13 CNC is characterised by Low Power Consumption, Simple & Quick Operation, Simple servicing activity between servicing intervals, Long Life of Parts.WHN/WHQ 13 CNC series are Universal Machine Tools for Jig Boring, Drilling Plane Milling, Milling of Surface of various shapes & Thread cutting.TypeWHN (Q) 13 CNCMax. Spindle Revolution2800 min-1Max. Output of main drive37 KwTable Transverse adjustment (X)3500 mmHead Stock Vertical (Y)2500 mmColumn Longitudinal adjustment (Z)1250 mmSpindle Pullout (W)800 mmTable Clamping Surface1800 * 2200 mmControl SystemHeidenhain TNC 430 MMeteringHeidenhainDrivesSiemensParts of WHN/WHQ 13 CNC Machine:Head Stock & Jib.Magazine and Too changer.Column.Longitudinal Bed and Column Side.Transversal Bed, Table Slide & Table.Operator’s Plateform & Electrical Cabinet.Electric Cabinet.SPOTS of Machine ControlMain Control PanelHandwheel ControllerHeadstock PanelControl Elements on Operators platformPanel on Electric Cabinet sidePanel inside the Electric CabinetParts of Main Control Panel:Panel of Control & Signalling ElementsScreen BF-120 of Heidenhain Control SystemKeyboard TE 120 Heidenhain Control SystemPanel of Control & Signalling:Chip conveyor ControllerSignal Lamps of diagnostic & SignallingController of manual tool coolingSwitch “Mode of Spindle control”Lubrication Signal LampOriented Stop Completion Signal LampPush button “Clockwise Sense of Rotation”Push button of Soft key bar cellPush button STOP Revolutions Push button “Anticlockwise Sense of rotation” Controller of tool cooling control selection Working Light Switch Correction of Pressure of cooling through Spindle centre Panel Control & Signalling Lower Part:Switch “Machine Group selection”Switch “Rapid Feed”Push button “Sense of rotation”Pish button “START NC”Push button “STOP NC”Push button “ EMERGENCY STOP”Push button “Machine Activation”Push button “Sense of Rotation”Keyboard TE 120Character’s Keyboard (file names Entering, Comments & other reading, Programming ISO/DIN).Numerical Keyboard (Numbers Entering, Axis selection).Keys of cursor Control & GoTo Key.Keys of Dialogue Commencement (Programming of travel movements, Entering tool Parameters cycles, Sub-Programs & reptation of Program part).Keys of Selection of Programming operational modes.Keys of Selection Machine operational modes.Feeds over ride.Revolution over side.Keys for Program or Files Handling (Program or file selection, MOD function, Help Function & Calculator).Screen BF-120Key for defination of Screen Partition.Key for Switching over of Softkey bar significance.Softkey for Selection of additional function.Keys for Switching over of SoftKey bar.Key for Switching over between active Machine mode & Programming mode.Machine Control Mode Switch on column of main Control Panel:-When the switch is OFF, selected Mode isMODE 1- automatic control mode.When the switch is ON, selected Mode isMODE 2- setting control mode.Control Elements on Electric Panel Side:Main Circuit Breaker Coil Switch.Signal Lamp of main Circuit Breaker Coil Activation.Push Button “MACHINE START”.Main Circuit Breaker.Control Element on HEADSTOCK:Neutral Control, Tool Clamping & ReleaseDetermination of Control Elements:-Button “Neutral Shifting”.Button “Release the Tool”.Button “Clamp the Tool”.Control Element on Operator’s Plateform:Control of Plateform movement & Softkey covers doorDetermination of Control Elements:-Plateform movement crossbar controller.Button “DOOR CONTROL”.Assignment of Plateform motion direction to the position of crossbar switch barLever AheadPlateform UpwardsLever backwardsPlateform DownwardsLever to LeftPlateform Shift OutLever to RightPlateform Shift inControl Element Inside Electric Panel:Lever Switch of control system Activation.Lever Switch of Emergency Unclamping.Emergency control of Machine group switch.Button control Emergency STOP group.Reset of Drives.Handwheel Controller:Button “Emergency STOP”.Handwheel for manual feed.Button for Handwheel Activation.Button for axis selection.Button for “Position Enter”.Button for selection of feed value (fine, normal).Button for selection of sense of Rotation (AntiClock, Stop, clock).Button for selection of feed Direction.Control of Machine basic functionsMachine Switching On and ActivationMachine is switched on with the help of control elements situated on electric cabinet side.Procedure to Start the machine:Switch the button on by its turn clockwise, then press it and turn anticlockwise – see arrows. (signal lamp get illuminated)Get machine connected to the main supply by turning the switch handle down to lower position and afterwards up to upper position- see arrows.Activate the machine by pressing of “MACHINE START” push button on side of electric panel – see arrowMachine can be activated also by pressing of “ON” button on main control pane.Together with switching of the main circuit breaker on there is power supply activated to control system logic unit.After completion of all internal tests of logic unit, there is message “POWER INTERRUPTED” displayed on control system screen.When this message is activated you shall activate the control system by pressing of the key “CE” of control system keyboard on main control panel – see arrow.If the message is not displayed, it is necessary to check out whether the lever switch of control system power supply inside the electric cabinet is ON.If the switch is off, it is necessary, before it’s switched ON, to discover the reason why it is off.If the switch is off and control system has not been activated , it is necessary to call for service engineer.If the Machine is activatedSpindle lubrication pump drive is running, spindle oil cooler drive is running, and electric motor of main drive fan is running.Hydraulic unit drive is running and lubrications of all machine groups is in progress.Menu of reference points evaluation is displayed on control system screen.Value of r.p.m. corresponding to the latest engaged gear is logged.Remedy of causes:Releases activation “EMERGENCY STOP” button by slight turn in the arrow direction.Move out the machine group from emergency limit position with the help of emergency control.After remedy of the cause, there is the information message “PRESS MACHINE START BUTTON” displayed on control system screen.Activate the Machine by “ MACHINE START” button on main control panel or on side of electric cabinet -arrow-After pressing of “MACHINE START” button following drives are activated: lubrication pump drive, spindle oil cooler drive, main drive fan electric drive, and drive of electric cabinet heat exchanger.The information message “PRESS NC START FOR CONTROL ACTIVATION”is displayed on control system screen at the same time.Tool Cooling ControlThe machine can be equipped with tool cooling, which can be control by several means that are identical for both, manual control mode and NC control mode.Cooling method selection shall be carried out by selectors (switches 1 and 2) on main control panel and by auxiliary function M71 to M77.By switching the selector -1- into left hand side position you pre-select the tool cooling controlled by NC program (using auxiliary M function).Cooling pump is activated by Auxiliary function M 13, M 14 or M 08.If the cooling method was not programmed by auxiliary function M 71 to M 77 before, cooling by two nozzles together is called out. (M 73)The cooling activated by auxiliary function M 13 and M 14 will be competed only on spindle continuous run. If the spindle run is stopped, tool cooling procedure is suspended.You can cancel the tool cooling initiated by auxiliary function M 13 and M 14 by program end and by auxiliary function M 08 and M 09 as well.The cooling initiated by auxiliary function M 08 is continuous and is suspended by neutral gear shift and by auxiliary function M 00, M 06 and M 34. Tool cooling activated by auxiliary function M 08 can be cancelled by program end and by auxiliary function M 09, M 14 and M 13.The control of Chips ConveyorThe machine can be equipped with chips conveyor, which is controlled by selector switch on main control panel –arrow-When the selector switch is switched into the middle position, the chip conveyor is OFF. In other two position of switch, the conveyor is in motion of appropriate direction.SoftkeysTo switch the Softkey bars over to previous meaning you will achieve by pressing of the softkey for return to previous softkey bar. This softkey is placed at the end of the mostly used softkey bars.Termination and Suspension of Softkey bars displaying.You can terminate displaying of softkey bar by pressing the “END” softkey.This kind of softkey bar display termination can be done only if softkey for return to previous softkey bar displayed.Softkey bar can be suspended by pressing of softkey bar call out button on main control panel –arrow- If you press the softkey bar call out button on main control panel again, the softkey bar displaying will be re-established.Softkey K1 Calls out the guide surfaces lubrication barSoftkey K2Calls out PLC window showing the list of upto 15 actually displayed error messages of the machine. The window shall update after each 5 seconds Softkey K3calls out PLC window with information regarding tool numbers of the tools at Headstock, regarding the tool changer gripper and regarding magazine at the place of tool change.Softkey K4Calls out the Data concering bearing temperatures, and concerning spindle dilatation value.Softkey K5Calls out the stage cooling control bar.Softkey K6Calls out the data regarding LD 650 faceplate on small PLC window.Softkey K9Activates lubrication of all guide surfaces of all machine groups.Softkey K10Activates lubrication of guide surfaces of machine group X.Softkey K11Activates lubrication of guide surfaces of machine group Y.Softkey K12Activates lubrication of guide surfaces of machine group Z.Softkey K13Activates lubrication of guide surfaces of machine group W.Softkey K14Activates lubrication of guide surfaces of machine group B.Softkey K26Sets the cooling control to minimum valueSoftkey K27Decreases the cooling control by 1 stage.Softkey K28Sets the cooling control to programmed valueSoftkey K29Increases the cooling control by 1 stage.Softkey K30Sets the cooling control to maximum value.Tool ChangeTool Change Procedure:Hold the tool by your hand and simultaneously press “RELEASE THE TOOL” button on machine headstock –arrow-Hydraulic distributor shall be activated after pressing of the button. Distributor will push out the clamping mechanism and tool will be released.As the confirmation of tool release completion, the signal lamp inside the “CLAMP THE TOOL” button shall start to illuminate. Pull out the tool from the hollow of working spindle in arrow direction.Insert new tool into the hollow of working spindlePress illuminating “CLAMP THE TOOL” button on machine headstock.After clamping command the Hydraulic distributor shall put the clamping device back to basic position and the tool inserted in hollow of working spindle shall be clamped by the force of Disc springs.Condition under which it is impossible to make the tool change:Spindle tipping is active.Spindle continuous run is active.Gear shifting is in progress.Some additional M-function is under execution.“EMERGENCY STOP” button is pressed.Some of the machine groups is at emergency limit position.Diagnostic MessagingError and information messagingPLC ERROR 00 -- MAJOR OVERLOAD TRIPPEDPLC ERROR 01 -- OVERLOAD TRIPPEDPLC ERROR 02 -- TOOL COOLING FAILUREPLC ERROR 03 -- SPINDLE DRIVE FAN OFFPLC ERROR 04 -- GOVERNOR NOT READYPLC ERROR 06 -- SPINDLE MAX. TORQUE EXCEEDEDPLC ERROR 07 -- SPINDLE DRIVE TEMPERATURE HIGHPLC ERROR 08 -- MAIN BEARING ASSEMBLY TEMPERATURE HIGH PLC ERROR 09 -- STOP! LIMIT MAIN BEARING ASSEMBLY TEMP.PLC ERROR 10 -- GOVERNOR NOT READYPLC ERROR 11 -- FEED CONTROLLER NOT READYPLC ERROR 12 -- FEED OVERLOADEDPLC ERROR 13 -- MACHINE AT LIMIT SWITCHPLC ERROR 15 -- GROUP CLAMPING FAILUREPLC ERROR 16 -- GROUP RELEASE FAILUREPLC ERROR 17 -- FEED CONTROLLER TEMP. HIGH PLC ERROR 18 -- HYDRAULIC UNIT PRESSURE HIGHPLC ERROR 19 -- PRESSURISING OF HYDRAULIC SYSTEM TOO LONGPLC ERROR 20 -- HYDRAULIC OIL LEVEL LOWPLC ERROR 21 -- HYDRAULIC UNIT FILTER CHOKEDPLC ERROR 22 -- HEADSTOCK LUBRICATION FAILUREPLC ERROR 24 -- COOLANT LEVEL HIGHPLC ERROR 25 -- COOLANT LEVEL LOWPLC ERROR 26 -- LUBRICATION PRESSURE ON FAILUREPLC ERROR 27 -- LUBRICATION PRESSURE OFF FAILUREPLC ERROR 28 -- LUBRICANT LEVEL LOWPLC ERROR 30 -- +24 V POWER SUPPLY FAILUREPLC ERROR 32 -- TOOL NOT CLAMPED ON TIME PLC ERROR 33 -- TOOL NOT RELEASED IN TIMEPLC ERROR 34 -- GEAR SHIFTING NOT DONE IN TIMEPLC ERROR 35 -- GEARSHIFT COMPLETEDPLC ERROR 46 -- IMPOSSIBLE TOOL CLAMPEDPLC ERROR 47 -- NO GEAR ENGAGEDPLC ERROR 49 -- SPINDLE MOTION DISABLEDPLC ERROR 50 -- RPM OUT OF RANGEPLC ERROR 51 -- IMPOSSIBLE! CONDITIONS NOT FULFILLEDPLC ERROR 54 -- REFERENCE POINT NOT EVALUATEDPLC ERROR 56 -- PRESET OUT OF RANGEPLC ERROR 57 -- ILLEGAL FUNCTIONPLC ERROR 58 -- AXIS DISABLED IN NC (MP10)PLC ERROR 59 -- W AXIS DISABLEDPLC ERROR 60 -- THIS FUNCTION IN MANUAL MODE ONLYPLC ERROR 61 -- PLATFORM NOT AT POSITIONPLC ERROR 62 -- SAFETY COVER OPENEDPLC ERROR 64 -- LACK OF FILTRATION WEB PLC ERROR 65 -- SPINDLE CENTRE COOLING FILTER CHOKEDMachine Legend:X - Transversal feedY - Spindle vertical shiftZ - Table slide longitudinal shiftW - Working spindle shiftB - Table rotationC - Working spindle rotationInspection and refilling of oil fillsIt shall be done at following locations:Machine Jib4- Lubrication unitMachine Headstock5- Table Drive GearboxHydraulic unit6- Operator’s PlatformMachine CODESS. No.FUNCTIONMACHINE CODE1Program StopM002Optimal StopM013Spindle Forward (CW)M034Spindle Reverse (CCW)M045Spindle StopM056Automatic Tool ChangeM067Coolant OnM088Coolant OffM099Spindle OrientationM19104th Axis ClampM25114th Axis UnclampM2612Program EndM3013Tool table InitializeM7014POT DownM7115ARM 600M7216Tool UnclampM7317ARM 1800M7418Tool ClampM7519ARM Back to Original PositionM7620POT UpM7721ATC ARM Trouble ShootingM9522Call Sub ProgramM9823End Sub ProgramM99 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download