GENERAL PUMP 2100372
GENERAL PUMPA member of the Interpump Group
2100372
Flat Surface Cleaner Swivel Repair Kit
REPAIR KIT INSTRUCTIONS
8 10
7
9 13 6
12
11
1
2
1) Disconnect the high pressure hose from the top of the swivel. 3
2) Loosen the 6mm allen head bolt in the collar holding the swivel to the FSC deck.
5 3) Slide the swivel and arm out the bottom of the deck.
4
4) Remove the nozzle arm from the swivel stem.
NOTE: A VISE MAKES THE NEXT (11) STEPS EASIER:
5) Secure the swivel in a vise with the bottom, end with three screws facing up.
16 6) Remove the three screws.
7) Grab the swivel stem with a plier or vise grip and pull the stem assembly out.
15
8) Remove the small stem and spring from the inside of the swivel
body bore.
14
ITEM PART # 1 2520030 2 2520028
DESCRIPTION RETAINER, BEARING RETAINER, BEARING
QTY 1 1
9) If the two dowel pins pressed into the end of the swivel body bore do not look worn they can be left in place. If they look worn, you need to pull them out and press in new pins. This can be difficult. Heating the outside of the housing helps to remove the pins, but this discolors the anodize. Replace the pins with new ones supplied in the kit. Tap in with punch and hammer.
10) Use an o-ring pick to remove the o-ring in the ID of the swivel body about half way down the swivel body bore.
3 2520027
SPACER, BEARING
2
11) Replace this o-ring with the one supplied in the kit.
4 2640004 5 2701012 6 2701011 7 2701010 8 2720007 9 2530008 10 2530007 11 2520029
BEARING O-RING O-RING O-RING SPRING
PIN STEM, SMALL
SNAP RING
2
12) A little grease on this o-ring helps the assembly process.
1
13) Lubricate the o-ring on the new small stem with a good quality
1
grease, drop the new spring into the small center bore at the bottom of the swivel body bore, then press the new small stem in the same
1
bore on top of the spring. Be sure the slots in the small stem drop
over the pins. 1
2
14) Slide the new swivel stem assembly into the swivel bore and secure with the three washers and screws.
1
15) Use a good quality thread sealant on the nozzle arm threads and
3
attach the arm to the swivel stem.
12 2710000 13 2520113 14 2200092
BACK UP RING STEM
SCREW, M5 X 16
1
16) Slide the swivel and arm assembly into the deck collar from the
1
bottom of the deck and position the nozzles so they are about one inch from the bottom of the brushes. Tighten the 6mm bolt on the
3
collar.
15 2200050 16 2500012
WASHER RETAINER, BEARING
3
17) Use a good quality thread sealant and reattach the high pressure
hose to the swivel.
1
General Pump is a member of the Interpump Group
Ref 300994 Rev. A 03-16
8
GENERAL PUMP 1174 Northland Drive ? Mendota Heights, MN 55120
Phone: 651.686.2199 ? Fax: 800.535.1745 ? e-mail: sales@ ?
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- general purpose cleaner tennant co
- safety data sheet 2171 general cleaner ecolab
- section 1 identification
- safety data sheet integra life
- general cleaner bp pro
- a174820 bostik ob1 multi surface cleaner safety data sheet d3 original
- professional flat surface cleaner
- specifications flat surface cleaner general pump
- general pump a member of the interpump group dcfscp18 gz flat surface
- general pump 2100372
Related searches
- vacuum penile pump devices
- pump it up
- replacement pump for coleman saluspa
- bestway saluspa pump heater replacement
- pump it up bounce house
- how does the heart pump blood
- pump it up birthday
- short pump medical center
- short pump medical plaza
- haldex hydraulics pump parts
- haldex hydraulic pump repair kit
- trails at short pump apartments