ENGLISH 2nd Generation Installation and 64452 / 07 User Guide

ENGLISH 64452 / 07

2nd Generation Installation and

User Guide

Required tools

Ruler Phillips screwdriver

Additional tools (depending on application)

Hammer

Wood block

Parts in the box

Latch with

Drive-in latch

rectangular faceplate

Strike

A

Mounting plate

B

Interior assembly

C

Battery pack

Exterior assembly

Adapter ring

D

Interior cover

E

Batteries

Keys

F

SmartKey tool

G

H

J

K

L

M

Latch screws

NP

Strike screws

Mounting plate screws

Q

R

S

T

03809

46780

Interior assembly screws

U

Interior cover screws

V

19571

49191

64109

Note: Part numbers are printed on screw bags.

Kevo Support: kevo/support

USA: 1-800-327-5625

Australia free call 1800 623 118 New Zealand free call 0800 736 776

1 / 11

? 2017 Spectrum Brands, Inc.

1 Prepare the door and check dimensions

If drilling a new door, use the supplied template and the complete door drilling instructions available at doorprep.

A Measure to con irm that the hole in the door

is either 2 1/8" (54 mm) or 1 1/2" (38 mm).

2 1/8" 54 mm

or 1 1/2" 38 mm

Note: Additional door preparation may be required for doors with 1 1/2" (38 mm) holes. Consult the deadbolt drilling instructions at doorprep

C Measure to con irm that the hole in

the door edge is 1" (25 mm).

1" 25 mm

B Measure to con irm that the backset is

either 2 3/8" or 2 3/4" (60 or 70 mm).

2 3/8" or 2 3/4" 60 or 70 mm

backset

D Measure to con irm that the door is either

1 3/8" (35 mm) or 1 3/4" (44 mm) thick.

1 3/8" or 1 3/4" 35 or 44 mm

Kevo Support: kevo/support USA: 1-800-327-5625 Australia free call 1800 623 118 New Zealand free call 0800 736 776

Note: If your door is 1 3/8" (35 mm) thick, make sure you have both sets of mounting plate screws (S and T). If you only have one set, please call Kevo Support for assistance: 1 800 327 5625

2 / 11

? 2017 Spectrum Brands, Inc.

2 Install the latch and strike

A Is the door edge chiseled?

YES

NO

or chiseled

not chiseled

Use latch "A". If the latch bolt is not already extended, extend the latch bolt as shown.

Use latch "B". If the latch bolt is not already extended, extend the latch bolt as shown.

B Hold the latch in front of the door hole, with the latch

face lush against the door edge.

A

B

A

B

C Is the D-shaped hole centered in the door hole?

YES

NO

or

D Which latch are you installing?

Latch "A"

or

Latch "B"

B

"UP" is on top

A N (2x)

"UP" is on top

wood block

D-shaped hole centered

D-shaped hole NOT centered

No adjustment is required. Proceed to next step.

Rotate latch face as shown to extend latch.

A

B

E Install strike on the door frame.

Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep.

Longer screws, Q, install closest to the door jamb.

Q (2x) R (2x)

C

door frame

Note: The longer screws, Q, (3" / 76 mm) must be used to maintain highest security.

Kevo Support: kevo/support

USA: 1-800-327-5625

Australia free call 1800 623 118 New Zealand free call 0800 736 776

3 / 11

? 2017 Spectrum Brands, Inc.

3 Install the exterior assembly

A What is the diameter of the hole in the door?

Diameter is 2 1/8" (54 mm)

Diameter is 1 1/2" (38 mm)

2 1/8" 54 mm

"E" is required for installation. Install "E" on "D".

D

or

1 1/2"

38 mm

"E" is not needed for installation. Discard "E".

E

E

B What is the thickness of your door?

Door is 1 3/8" (35 mm) thick

Door is 1 3/4" (44 mm) thick

or

1 3/8" 35 mm

1 3/4" 44 mm

Use the shorter screws.

S

Note: If you only have one set of mounting screws, call Kevo Support for assistance: 1 800 327 5625

Use the longer screws.

T

Note: If you only have one set of mounting screws, they are compatible with your door thickness, and you may proceed with installation.

C Install exterior assembly and mounting plate.

a Locate mounting plate (G).

Note: It is on the back of the interior assembly.

G

b

Cable goes underneath latch.

c G

d S or T (2x)

Tighten screws evenly

e T

D

Rotate torque blade to align with D-shaped hole.

Route cable through center hole, then push cable into bottom hole.

Keep parallel to edge of door

F Insert key and test latch. If

latch does not extend or retract smoothly, adjust screws (T). Remove key when inished and make sure the latch bolt is fully extended.

Kevo Support: kevo/support USA: 1-800-327-5625 Australia free call 1800 623 118 New Zealand free call 0800 736 776

4 / 11

? 2017 Spectrum Brands, Inc.

4 Install the interior assembly

A Remove battery cover and battery pack from interior assembly.

a Make sure

turnpiece is in the

vertical position.

b Remove

interior cover.

K

H

K

vertical

B Connect cable and install interior assembly.

a Make sure

cable "clicks" into place.

H

b

b

c Remove

battery pack.

J H

Do not install batteries yet.

c Tuck

cable into

interior

housing.

d Push turnpiece shaft

onto torque blade.

torque blade

e Secure with

screws.

turnpiece shaft

bottom hole

U (2x)

If connector lever is extended, push it back down.

Tip

Use lever if you need to remove cable.

Kevo Support: kevo/support

USA: 1-800-327-5625

Australia free call 1800 623 118 New Zealand free call 0800 736 776

5 / 11

? 2017 Spectrum Brands, Inc.

 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download