No configuration is needed for the relays on the GCRL3A module. Global ...
? GCRL3A No configuration is needed for the relays on the GCRL3A module. However, state controls are provided for testing purposes.
6. Repeat for Remaining Modules
Repeat steps 3 through 5 for all Global Connect modules in the chassis.
TROUBLESHOOTING
Global Connect modules can be reset to defaults by depressing the first (left-most) LED/light pipe of each module for 10 seconds at which point the LED will flash rapidly indicating a reset will occur. Additional information and instructions can be found in the Global Connect User Guide. Download from our web site at downloads
CONTACT US
Global Cach? 160 East California Street PO Box 1659 Jacksonville, Oregon 97530 USA Phone: 541-899-4800 Email: support@ Web:
Global Connect
Quick Start Guide
This Quick Start Guide covers initial setup for all Global Connect devices. For detailed configuration instructions, please see the Global Connect User Guide on our web site at downloads
Copyright ?2020 Global Cach?. All rights reserved. PN: 110518-01 ver2. Information subject to change without notice.
GETTING STARTED 1. Connect Global Connect
Connect Global Connect to the network via Ethernet. Power the unit by attaching the included power supply or, if using a PoE capable unit, by connecting the unit to a PoE switch on the RJ45 connector marked "PoE IN".
2. Discover Global Connect Modules
Download and run iHelp (). Wait up to 20 seconds for all modules to be discovered.
3. Open Configuration Web Pages
Right click on the first unconfigured module in iHelp and select Configure or manually enter the unit's IP address in a browser address bar.
4. Configure Network Settings
Global Connect modules default to DHCP enabled. To set a static IP address, select Network Settings. Change DHCP to Disabled, and enter the desired IP Address, Subnet Mask, Gateway, and DNS servers. Click Apply Changes followed by Back to return to the home page.
2
5. Configure Module Settings
Click the module's setting tab.
Depending on the type, configure the module for control of the attached devices.
? GCHMX3
The GCHMX3 module allows for 3:1 HDMI switching, as well as CEC control via CEC injection. No configuration of the switch is necessary. However, to test the switching action set the Output Port to On (enabling the switch), then select the input port that corresponds to the desired input device, and select Apply Changes.
? GCIR3
The GCIR3 module allows for IR output, sensor input, or IR reception through its 3 independent ports. Each module includes 3 flashing IR emitters and one non-visible IR blaster capable of long-range IR transmission. Additionally, sensor input cables and IR receiver cables can be purchased separately. Plug the emitter, sensor, or IR receiver cables into any of the 3 ports. If an IR blaster will be used plug it into IR port 3. On the configuration webpage, select Emitter, IR Blaster, Sensor/Sensor Notify, or IR Receiver depending on which cable is plugged into each port, then select Apply Changes. For the difference between Sensor and Sensor Notify please refer to the online User Guide.
? GC232
The GC232 module allows for serial control of RS232 devices. The module must be configured with serial settings that match the connected serial device. These settings can often be found in the connected serial device's manual. Once these settings have been selected, select Apply Changes.
3
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- how to reset your global protect vpn password
- reset change password using adss quest global
- check „change password then proceed to log in gfk
- no configuration is needed for the relays on the gcrl3a module global
- microsoft password reset encore
- supplyweb global supplier request password reset tenneco
- assist account unlock password reset user guide sutherland global
- global foundryview password reset
- click on „forgot your password gfk
- electronic coded lock instructions important default personal password
Related searches
- top 10 careers needed for the future
- what is needed for a home loan
- why immigration is bad for the economy
- what is needed for photosynthesis to occur
- what act score is needed for scholarships
- what is needed for photosynthesis occur
- what is needed for photosynthesis
- solve the equation on the interval calculator
- what else is needed for photosynthesis
- the rows on the periodic table
- why immigration is good for the economy
- place the state on the map quiz