Rolling Steel Door 600 Specs
[pic]
SECTION 08330
ROLLING SERVICE DOORS
COIL-AWAY™ MODEL 600
Display hidden notes to specifier by using “Tools”/”Options”/“View”/”Hidden Text”.
** NOTE TO SPECIFIER ** Overhead Door Corporation; rolling service door products.
1 GENERAL
1. SECTION INCLUDES
** NOTE TO SPECIFIER ** Delete items below not required for project.
A.
2. RELATED SECTIONS
** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
A.
B. Section 06200 - Finish Carpentry: Wood jamb and head trim.
C. Section 08333 - Security Grilles.
D. Section 08710 - Door Hardware: Product Requirements for cylinder core and keys.
E. Section 09900 - Painting: Field applied finish.
F. Section 16130 - Raceway and Boxes: Conduit from electric circuit to door operator and from door operator to control station.
G. Section 16150 - Wiring Connections: Power to disconnect.
3. REFERENCES
** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.
A.
B. NFRC 102 - Test Procedure for Measuring the Steady-State Thermal Transmittance of Fenestration Systems.
C. ASTM E 90 - Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Element.
D. ASTM E 330 - Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference.
E. ASTM A 653 - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process.
F. ASTM A 666 - Standard Specification for Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar.
G. ASTM A 924 - Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process.
H. ASTM B 221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.
I. NEMA 250 - Enclosures for Electrical Equipment (1000 Volts Maximum).
J. NEMA MG 1 - Motors and Generators.
4. DESIGN / PERFORMANCE REQUIREMENTS
A. Single-Source Responsibility: Provide doors, tracks, motors, and accessories from one manufacturer for each type of door. Provide secondary components from source acceptable to manufacturer of primary components.
B. Products Requiring Electrical Connection: Listed and classified by Underwriters Laboratories, Inc. acceptable to authority having jurisdiction as suitable for purpose specified.
5. SUBMITTALS
A. Submit under provisions of Section 01300.
B. Product Data: Manufacturer's data sheets on each product to be used, including:
1. Preparation instructions and recommendations.
2. Storage and handling requirements and recommendations.
3. Details of construction and fabrication.
4. Installation instructions.
C. Shop Drawings: Include detailed plans, elevations, details of framing members, anchoring methods, required clearances, hardware, and accessories. Include relationship with adjacent construction.
** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
D.
E. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) long, representing actual product, color, and patterns.
F. Manufacturer's Certificates: Certify products meet or exceed specified requirements.
G. Operation and Maintenance Data: Submit lubrication requirements and frequency, and periodic adjustments required.
6. QUALITY ASSURANCE
A. Manufacturer Qualifications: Company specializing in performing Work of this section with a minimum of five years experience in the fabrication and installation of security closures.
B. Installer Qualifications: Installer Qualifications: Company specializing in performing Work of this section with minimum three years and approved by manufacturer.
** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
C.
1. Finish areas designated by Architect.
2. Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.
3. Refinish mock-up area as required to produce acceptable work.
7. DELIVERY, STORAGE, AND HANDLING
A. Store products in manufacturer's unopened packaging until ready for installation.
B. Protect materials from exposure to moisture. Do not deliver until after wet work is complete and dry.
C. Store materials in a dry, warm, ventilated weathertight location.
8. PROJECT CONDITIONS
A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.
9. COORDINATION
A. Coordinate Work with other operations and installation of adjacent materials to avoid damage to installed materials.
10. WARRANTY
** NOTE TO SPECIFIER ** Include the following warranty paragraph for Model 600, 610, 620, 625 or 627 rolling service doors and Model 653 shutters not provided as a system with operators. Delete if not applicable.
A.
** NOTE TO SPECIFIER ** Include the following Optional PowderGuard Finish warranty paragraph if included for the Door(s) specified. Delete if not applicable.
B.
** NOTE TO SPECIFIER ** Include the one of the following PowderGuard Finish warranty paragraphs for the finish specified. Delete if not applicable.
1.
2. PowderGuard Zinc Base Coat applied to guides, bottom bar, headplates plus PowderGuard Premium applied to curtain and top coat for guides, bottom bar, headplates: Manufacturer’s limited Zinc Finish warranty for 4 years.
3. PowderGuard Textured: Applied to curtain, guides, bottom bar, headplates: Manufacturer’s limited Textured Finish warranty for 3 years.
4. PowderGuard Zinc Base Coat applied to guides, bottom bar, headplates plus PowderGuard Textured applied to curtain and top coat for guides, bottom bar, headplates: Manufacturer’s limited Zinc Finish warranty for 4 years.
5. PowderGuard Max: Applied to curtain, guides, bottom bar, headplates: Manufacturer’s limited Max Finish warranty for 5 years.
2 PRODUCTS
1. MANUFACTURERS
A. Acceptable Manufacturer: Overhead Door Corporation, 2501 S. State Hwy. 121, Suite 200, Lewisville, TX 75067. ASD. Tel. Toll Free: (800) 275-3290. Phone: (469) 549-7100. Fax: (972) 906-1499. Web Site: . E-mail: info@.
** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
B.
C. Requests for substitutions will be considered in accordance with provisions of Section 01600.
2. ROLLING SERVICE DOORS
** NOTE TO SPECIFIER ** Overhead Door Corporation Model 600 Light Commercial Rolling Service Doors are available up to a standard maximum width of 16 feet and a standard maximum height of 16 feet. Edit as required to suit project requirements.
A.
1. Curtain: Interlocking roll-formed galvanized steel slats, flat crown profile type CAW, 26 gauge for widths up to 12 feet 4 inches (3.75 m), 24 gauge for widths up to 16 feet (4.88 m). End of each slat shall be locked from lateral movement by a staking lock system. (Galvanized alternate malleable end locks.)
2. Finish:
a. Curtain slats and hood shall be galvanized in accordance with ASTM A 653 and receive rust-inhibitive, roll coating process, including 0.2 mils thick baked-on prime paint, and 0.6 mils thick baked-on polyester top coat.
** NOTE TO SPECIFIER ** Select one of the following two paragraphs for Polyester top coat or Powder top coat and delete the one not required. Polyester top coat is standard.
1)
a) White polyester.
b) Brown polyester.
2) Powder Coat:
** NOTE TO SPECIFIER ** PowderGuard Premium polyester powder coat available in 197 colors; custom color match options available.
a)
3) Non-galvanized exposed ferrous surfaces shall receive one coat of rust-inhibitive primer.
3. Weatherseals: Vinyl bottom seal.
4. Bottom Bar: Extruded aluminum.
5. Guides: Roll-formed galvanized steel shapes attached to continuous galvanized steel wall angle.
a. Finish: PowderGuard Premium powder coat, color as selected by Architect.
6. Brackets: Galvanized steel to support counterbalance and curtain.
a. Finish: PowderGuard Premium powder coat, color as selected by Architect.
7. Counterbalance: Helical torsion spring type housed in a steel tube or pipe barrel and supporting the curtain with deflection limited to 0.03 inch per foot of span. Spring tension shall be adjustable.
** NOTE TO SPECIFIER ** Select one of the following two paragraphs and delete the one not required.
8.
9. Hood: 24 gauge galvanized steel with intermediate supports as required.
** NOTE TO SPECIFIER ** Select one of the following paragraphs for manual operation or electric motor operation and delete the one not required.
10.
** NOTE TO SPECIFIER ** Select one of the following manual operation paragraphs and delete the ones not required.
a.
b. Chain hoist for doors over 100 SF.
** NOTE TO SPECIFIER ** Include the following paragraph is electric motor operation is required and delete if not required.
11.
a. Sensing Edge Protection:
** NOTE TO SPECIFIER ** Select one of the following two paragraphs and delete the one not required.
1)
2) Electric sensing edge.
b. Operator Controls:
** NOTE TO SPECIFIER ** Select one of the following operation paragraphs and delete the one not required.
1)
2) Key operation with open, close, and stop controls.
3) Push-button and key operated control stations with open, close, and stop buttons.
** NOTE TO SPECIFIER ** Select one of the following location paragraphs and delete the one not required.
4)
5) Controls for exterior location.
6) Controls for both interior and exterior location.
** NOTE TO SPECIFIER ** Select one of the following two paragraphs and delete the one not required.
7)
8) Controls flush mounted.
c. Special Operation:
** NOTE TO SPECIFIER ** Select one of the following operation paragraphs and delete the one not required.
1)
2) Radio control operation.
3) Card reader control.
4) Photocell operation.
5) Door timer operation.
6) Commercial light package.
7) Explosion and dust ignition proof control wiring.
d. Motor Voltage: 115/230 single phase, 60 Hz.
12. Wind load Design:
** NOTE TO SPECIFIER ** Select the following paragraph if required. Contact the manufacturer for current data on FBC Certification and insert below.
a.
13. Operation: Design door assembly, including operator, to operate for not less than 20,000 cycles.
14. Locking:
** NOTE TO SPECIFIER ** Select one of the following paragraphs and delete the ones not required.
a.
b. Exterior slide lock for manually operated mini-warehouse doors.
c. Chain keeper locks for chain hoist operation.
d. Interior slide bolt lock for electric operation.
e. Cylinder lock for electric operation.
15. Wall Mounting Condition: Face-of-wall.
** NOTE TO SPECIFIER ** Model 610 doors are suitable for heavy duty industrial and other similar projects.
3 EXECUTION
1. EXAMINATION
A. Verify opening sizes, tolerances and conditions are acceptable.
B. Examine conditions of substrates, supports, and other conditions under which this work is to be performed.
C. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
2. PREPARATION
A. Clean surfaces thoroughly prior to installation.
B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
3. INSTALLATION
A. Install in accordance with manufacturer's instructions.
B. Use anchorage devices to securely fasten assembly to wall construction and building framing without distortion or stress.
C. Securely and rigidly brace components suspended from structure. Secure guides to structural members only.
D. Fit and align assembly including hardware; level and plumb, to provide smooth operation.
** NOTE TO SPECIFIER ** Select the following paragraph for electric operation of coiling doors and delete if not required.
E.
F. Coordinate installation of sealants and backing materials at frame perimeter as specified in Section 07900.
G. Install perimeter trim and closures.
H. Instruct Owner’s personnel in proper operating procedures and maintenance schedule.
4. ADJUSTING
A. Test for proper operation and adjust as necessary to provide proper operation without binding or distortion.
B. Adjust hardware and operating assemblies for smooth and noiseless operation.
5. CLEANING
A. Clean curtain and components using non-abrasive materials and methods recommended by manufacturer.
B. Remove labels and visible markings.
C. Touch-up, repair or replace damaged products before Substantial Completion.
6. PROTECTION
A. Protect installed products until completion of project.
END OF SECTION
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- toyota highlander specs and dimensions
- specs on 2017 toyota highlander
- rolling negative equity into a used car
- 4 6 ford engine specs horsepower
- sasha rolling stones
- engine specs by vin number
- tableau rolling average
- the rolling stones
- rolling over 401k to ira
- rolling over a 401k to an ira
- rolling ira to 401k
- rolling ytd excel formula