UNITS OF CONCENTRATION 2016 - Vancouver Island …

UNITS OF CONCENTRATION

There are a number of different ways of expressing solute concentration that are commonly used. Some of these are listed below. Molarity, M = moles solute/liter of solution Normality, N = equivalents of solute/liter of solution Weight %, Wt % = mass ratio x 100% = mass of solute/mass of solution x 100% Parts per million, ppm = mass ratio x 106 = mass of solute/mass of solution x 106 Mass per volume, mg/L = mass of solute/liter of solution molality, m = moles of solute/mass of solvent (kg) mole fraction, = moles of solute/total moles of solution

Concentrations expressed as ppm and N are less familiar to some students at this stage.

Parts per million: Parts per million concentrations are essentially mass ratios (solute to solution) x a million (106). In this sense, they are similar to wt %, which could be thought of as parts per hundred (although nobody uses this term). Since 106 milligrams = 1 kg, 1 mg/kg is equivalent to 1 ppm. Similarly, 1 ?g/g and 1ng/mg are also equivalent to 1 ppm.

Given that the density of dilute aqueous solutions is ~1.00 kg/L, 1 mg/L of solute in freshwater 1 ppm. This is true for most freshwater and other dilute aqueous solutions, but not the case for seawater and concentrated wastewater solutions, where the density of the solution is greater than 1.00 kg/L.

Other variations on this theme include: ppt ? parts per thousand (used for common ions in sea water) ppb ? parts per billion (used for trace heavy metals and organics) pptr ? parts per trillion (used for ultratrace metals and organics)

The following table summarizes common mass ratios for solutions and solids.

Unit

In General

Dilute Aqueous Solutions

ppm

mg/kg

?g/g

mg/L

?g/mL

ppb

?g/kg

ng/g

?g/L

ng/mL

pptr

ng/kg

pg/g

ng/L

pg/mL

UNITS OF CONCENTRATION 2016.doc

To convert concentrations in mg/L (or ppm in dilute aqueous solution) to molarity, divide by the molar mass of the analyte to convert mass in mg into a corresponding number of moles. Example: What is the molarity of a 6.2 mg/L solution of O2(aq)?

To convert from molarity to mg/L (or ppm in dilute aqueous solution), multiply by the molar mass of the analyte to convert moles into corresponding number of moles. Example: The Maximum Acceptable Concentration (MAC) of Pb in drinking water is 10 ppb. If a sample has concentration of 55 nM, does it exceed the MAC?

Note 1: In seawater, 1.00 mg/L 1.00 ppm since the density of seawater is 1.035 kg/L. Hence, 1.00 mg/Lsewater = 1.00 mg/L x 1 L/1.035 kg = 0.966 mg/kg or 0.966 ppm Example: The concentration of K+ in seawater is reported as 10.6 mM. Convert this conc to ppm.

UNITS OF CONCENTRATION 2016.doc

Note 2: Some concentrations are expressed in terms the species actually measured e.g., mg/L of NO3- (mass of nitrate ions per liter) Or in terms of a particular element in a species that was measured. e.g., mg/L of NO3- - N (mass of nitrogen in the form of nitrate ions per liter) To convert from one to the other of these, use the molar mass ratio of the element to that of the chemical species measured. In the example above use, 14 mg N/62 mg NO3-. It is important to clearly report unit values to avoid serious error in interpretation of results. Similar situations arise in reporting the concentrations of ammonia-nitrogen, phosphate-phosphorous and others. Example: A water sample has a measured phosphate concentration of 6.8 ?M. Express this as ?g/L PO43- and ppb PO43 ? P.

Note 3: Some aggregate parameters are reported in terms of a single surrogate species. e.g., total hardness is usually reported as the mass of CaCO3 that would be required to provide the same number of moles of calcium ions. Example: A groundwater sample has been determined to contain 100. ppm Ca and 80. ppm Mg by flame atomic absorption spectrophotometry. Express the total hardness as ppm CaCO3.

UNITS OF CONCENTRATION 2016.doc

Example: A water sample has been found to contain 0.6 mM of As, F- and NO3-. The drinking water guidelines for arsenic, fluoride and nitrate-nitrogen are 10 ppb, 1.5 ppm and 10 ppm, respectively. Does this sample exceed the drinking water guidelines for arsenic, fluoride or nitrate - nitrogen?

Example: A commercial bleach solution NaOCl(aq) is reported to be 12.5% (weight). If the density is 1.05 g/mL, calculate the molar concentration.

Example: A standard solution is prepared by dissolving 225 mg of sodium thiosulfate pentahydrate in a one litre volumetric flask. After thoroughly mixing, 5.00 mL was transferred to a 250. volumetric flask and diluted to the mark. What is the molar concentration of thiosulfate in the final solution?

UNITS OF CONCENTRATION 2016.doc

Normality is a concentration unit that is still encountered in many texts and lab manuals. It has particular advantages when carrying out acid/base and redox titration calculations,

however it can be confusing for the uninitiated. Normality is defined as the number of equivalents of solute per liter, where an equivalent is defined as a mole of reacting species (H+ or e-). Normality is always a multiple of Molarity.

N = K x M where K = #equivalents per mole, K is an integer constant 1

Hence; Equiv. Weight = M.W./K

and # equivalents of solute = mass of solute/equiv. weight

K for a particular species is defined by the context of the chemical reaction (acid/base vs redox) and the number of moles of H+ or e- exchanged per mole of reacting substance.

For acid/base rxn's: K is the number of moles of H+ ions produced or neutralized per mole of acid or base supplied. Thus,

Acid/base

HCl H2SO4 CaCO3 Al(OH)3

K (equiv/mol)

1 2 2 3

M.W. (g/mol)

36.5 98.1 100 78.0

E.W. (g/equiv)

36.5 49.0 50.0 26.0

Thus, for the reaction; CaCO3 + 2 H+ ? Ca2+ + H2CO3

there are 2 moles of H+ transferred per each mole of CaCO3 reacted, so K for CaCO3 (in

this context) is equal to 2 equiv/mol and the equivalent weight of CaCO3 is equal to 50

g/equiv.

For oxidation/reduction reactions, K is the number of moles of e- transferred per mole of oxidant or reductant in the balanced half-reaction.

Balanced half reaction Fe3+ ? Fe

I2 ? 2 I2 S2O32- ? S4O62-

K (equiv/mol) 3 2 1

Thus, for the reaction; I2 + 2 S2O32- ? 2 I- + S4O62-

there are 2 moles of electrons transferred per mole of I2 reacted, so K for I2 (in this

context) is 2 equiv/mol.

UNITS OF CONCENTRATION 2016.doc

 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download