REALFORCE Software User's Manual
[Pages:51]REALFORCE Software User's Manual
WriningAn electrical product may cause a fire, injury, or death if the safety precautions are not observed.
Thank you for purchasing our product. This user manual describes the important precautions to prevent an accident and the methods of handling this product. Please read this manual carefully and use this product safely. This manual should be kept in a handy place for reference.
2020 Topre Corporation
March 2020(Fourth edition) 1
Contents
Introduction
4
1. REARLFORCE Software Startup
4
1.1. Installing procedure
4
1.2. Starting REALFORCE software
6
2. Keyboard settings
8
2.1. Adjusting the Actuation Point (for Models with the APC Function Only)
8
2.1.1. Individual setting
8
2.1.2. Batch setting
9
2.2. Adjust RGB-LED (For the REALFORCE RGB Series Only)
10
2.2.1. User setting
10
2.2.2. Lighting ON key
12
2.2.3. Lighting ON key (with backlight)
13
2.2.4. Rainbow wave
14
2.2.5. Shooting star
14
2.2.6. Color bar
15
2.2.7. Random
15
2.2.8. Demo mode
16
2.2.9. Stop Effect
16
2.2.10. Brightness adjustment
16
2.3. Selecting the key to be locked
17
2.4. Adjusting keyboard settings
19
2.4.1. Save to keyboard
19
2.4.2. Read factory-set conditions
21
2.4.3. Exchange Caps Lock and Ctrl key
22
2.4.4. Settings of Indicator LED Lights (for the REALFORCE R2 Series only)
23
3. Mouse settings
24
3.1. Set button functions
24
3.1.1. Settings for Button1 and Button2
24
3.1.2. Settings for Button3, Button4, Button5 and Button6
25
3.2. Adjust LED
29
3.2.1. Light settings
29
3.2.2. Color settings
30
3.2.3. Brightness settings
30
3.3. Adjust Sensor function
31
3.3.1. Change DPI-Setting being used
31
3.3.2. Change DPI
32
3.3.3. Switching between enable/ disable DPI-Setting
33
3.3.4. Lift-Off-Distance-Setting
33
2
3.3.5. View Report Rate
34
3.4. Adjusting mouse settings
35
3.4.1. Save to mouse
35
3.4.2. Read factory-set conditions
37
4. Common settings
38
4.1. Updating firmware
38
4.2. Set folder
42
4.3. Link to HP
43
4.4. Version information
44
4.5. Profile
45
4.5.1. Saving profile
45
4.5.2. Calling profile
46
4.6. Selecting a device when two or more devices are connected
48
5. Exiting software
50
6. If you have a problem
51
3
Introduction
This User's Manual explains how to use REALFORCE with its exclusive software to adjust the settings for REALFORCE.
1. REARLFORCE Software Startup
1.1. Installing procedure First, install the installer from the following URL: realforce.co.jp/support/
Caution!
The software should be downloaded and used at your own risk. Topre will assume no responsibility for any problem or damage that has taken place as a result of downloading or using the software. Double-click and execute the installer. "Select language" will be displayed. Select "Japanese" or "English" and click "Next" in the lower right corner.
4
Read the "License agreement". If you agree to the provisions, check "Agree" in the lower left section and then click "Install" in the lower right corner. The software cannot be installed if "Do not agree" is checked.
The software will automatically be installed. Wait for a while. When the installation has finished, a message to that effect and a link to the home page will be displayed. Click Complete in the lower right corner to finish the installation.
5
1.2. Starting REALFORCE software When the software has been installed, a short cut will be created on the desktop. Double-click the short cut to start the software. If the software is started without the REALFORCE series connected, "Unable to detect the device" will be displayed on the screen. The REALFORCE series may not be recognized even when it is connected in this status. If that is the case, exit the software once by pressing the ? button in the upper right corner. Connect the REALFORCE series and start the software again.
6
When REALFORCE is connected and the software is started, a keyboard or mouse is displayed on the screen.
Tab Menu
Profile Save and Load
Keyboard View Tab Menu
Select Device Profile Save and Load
Mouse View
Select Device
7
2. Keyboard settings
2.1. Adjusting the Actuation Point (for Models with the APC Function Only) The APC tab sets the Actuation Point. To set the key switch to the ON position, click as shown in the APC tab.
Supplementary APC is the abbreviation for actuation point changer. Note For models without the APC function, the APC tab is grayed out and will not respond to clicks.
2.1.1. Individual setting The Individual setting key sets the Actuation Point of each one of the keys to 1.5 mm, 2.2 mm, or 3.0 mm. Keys whose Actuation Point is set to 1.5 mm are shown in blue, those with an Actuation Point set to 2.2 mm are shown in green, and those set to 3.0 mm are in red. The default Actuation Point for all the keys is 1.5 mm.
The Actuation Point for a key can be set by clicking one key at a time with the mouse or enclosing the key while holding down the left mouse button. After the setting, the colors of the screen and the keyboard change.
8
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- realforce software user s manual
- factorytalk view site edition user s guide
- zoomtext troubleshooting tips
- operating instructions read me first model
- operating instructions basic guide model no
- bluetooth mouse or keyboard not recognized after reboot on
- tablet pc model v7023d
- htk visual quickstart guide
- k st20 configuration help
- supernova irie at
Related searches
- excel user manual pdf
- excel 2016 user manual pdf
- excel user manual free download
- blackrock aladdin user s guide
- microsoft office 2010 user s guide
- microsoft project user manual pdf
- sap user manual pdf
- microsoft flight simulator 2020 user manual pdf
- unity user manual pdf
- change another user s password
- air force airman s manual pdf
- pa driver s manual 2018