KP41T65 - ePanorama



Sony KP41T65 Chassis RA2A

Looks like AGC overload on live video. Test patterns OK.

C5145 10uf50v located on the PT board

Wayne Vanaman

Omega Electronics

6904 W Fairfield Dr

Pensacola, Fl. 32506-3310

Sony PTV is a 1998 model KP41T65.

The set will not turn on until about the 3rd, or 4th try.

When the picture comes in, it is in from both sides about 2 inches, and

Down from the top, and up from the bottom about 2 inches. After about 5 minutes,

the picture finally fills the screen, but it looks a little milky, or some

what out of focus. They say if it is left on too long, it will shut

off

A can of circuit coolant lead me straight to C655 (2200 ufd. @ 25VDC), on

power supply module. Read about 1650 ufd. when cold, and about 1850 ufd.

after heated up.

LeRoy Westlund

|KP41T65 |

| |

|Subject |

|ANODE AND HV LEAD P/N |

| |

SYMPTOMS

What are the part numbers for the anode and focus leads? 

RESOLUTION

Anode 1-779-095-21

Focus Lead 1-900-231-42 

|KP41T65 |

| |

|Subject |

|NO AUDIO, IC403 |

| |

SYMPTOMS

No audio, 

RESOLUTION

IC403 defective. Replaced IC403 or the A Board. Your assistance is need to obtain the necessary information to find the solution to this failure.. Please contact your Tech Rep. with the information required below.

The Vcc of audio amp may be higher  than expected.

Vcc is provided from PIT but no regulator in this line so the voltage varies by a variation of PIT winding. To verify that we want to know the voltage of Vcc.

Please measure the voltage between pin 9(Vcc) and pin 3(GND) of IC404. It's  supposed to be around 30V. If our assumption is correct then additional diode in Vcc line will help an IC404 failure. Design will determine type of diode and the location of the insertion.

|KP41T65, KP46C65 |

| |

|Subject |

|P/N FOR IC5052 INCORRECT, 875953389 |

| |

SYMPTOMS

P/N for IC-5052 in the S/M 8-759-487-47 comes up no longer available in the system. 

RESOLUTION

The correct P/N is 8-759-533-89. 

|KP53S15, KP53S25, KP53S55, KP53S65, KP53V15, KP53V16, KP53V25, KP53V35, KP53V45, KP53V75, KP53V90, KP53XBR200, |

|KP53XBR35, KP53XBR45, KP53XBR4CT |

| |

|Subject |

|L and F Screens Sub |

| |

SYMPTOMS

The L Screen is No Longer Available. Is there a sub? 

RESOLUTION

Both the L screen and F Screen must be replaced with the part numbers below.

Failure to replace both screens will cause picture degrading.

Change screens to Part Numbers:

L Screen 4-070-525-01

F Screen 4-084-702-02

|KV27FV300, KV32FV300, KV36FV300 |

| |

|Subject |

|Picture blinked no luminance |

| |

SYMPTOMS

Picture blinked on and off but no luminance. 

CAUSE

Problem look like unit had bad connection on the BC board check pin 7 of CN306 (Y signal) good, but CN306/pin 12 no luminance out. Checked CN306/pin 16, 14v missing !

14v come from GK board CN605 pin1 . 14v missing found PS601open replace fixed  .

Service manual is wrong Cn 605 pin 1 on the GK board show 5v it incorrect should be 14v and pin 2 should be 5v 

RESOLUTION

Found PS601open replace fixed .

Service manual is wrong CN605/pin 1 on the GK board show 5v it's incorrect.

Should be 14v and CN605/pin 2 should be 5v 

|Part Number |Reference Number |Description |

|157633721 |PS601 |Link IC |

|KP41T65 |

| |

|Subject |

|AUX PICTURE SNOWY, IC001 |

| |

SYMPTOMS

Aux picture is snowy. 

RESOLUTION

Found IC001 on the A Board defective. 

|Part Number |Reference Number |Description |

|8-752-894-96 |IC001 |CXP85856A- |

|KP41T65 |

| |

|Subject |

|DEAD, Q502 |

| |

SYMPTOMS

Dead. 

RESOLUTION

Replaced Q502 on the G Board. 

|Part Number |Reference Number |Description |

|8-729-024-05 |Q502 |2SD2348 |

|KP41T65 |

| |

|Subject |

|DEAD, T504 |

| |

SYMPTOMS

Dead. 

RESOLUTION

Found T504 defective on the G Board. 

|Part Number |Reference Number |Description |

|1-453-238-11 |T504 |FBT |

|KP41T65 |

| |

|Subject |

|DEAD, T605 |

| |

SYMPTOMS

Primary input okay, extremely low secondary outputs. 

RESOLUTION

Found the secondary windings T605/pin 9-12 shorted to windings T605/pin 13-14.

Replaced T-605 

|Part Number |Reference Number |Description |

|142998511 |T605 |CONVERTER (PIT) |

|KP41T65 |

| |

|Subject |

|PICTURE JUMPING, IC808 |

| |

SYMPTOMS

Picture jumping. 

RESOLUTION

Replaced IC808 on the G Board. 

|Part Number |Reference Number |Description |

|8-759-464-79 |IC808 |PM0011AS |

|KP41T65 |

| |

|Subject |

|SHUTS DOWN, IC601, R608 |

| |

SYMPTOMS

Unit shuts down. 

RESOLUTION

Found IC601 & R608 defective on the G Board. 

|Part Number |Reference Number |Description |

|8-729-041-12 |IC601 |0.1 OHM FUSE 1/2W |

|1-202-933-61 |R608 |0.1 OHM FUSE 1/2W |

|KP41T65 |

| |

|Subject |

|SHUTS DOWN, R586 |

| |

SYMPTOMS

Unit shuts down. 

RESOLUTION

Found R586 on the G Board defective. 

|Part Number |Reference Number |Description |

|1-260-292-11 |R586 |1 OHM 1/2W |

|KP41T15, KP41T25, KP41T35, KP41T65, KP43T70, KP46C36, KP46C65, KP46C70, KP46S15, KP46S17, KP46S25, KP46V25, |

|KP46V35, KP48S35, KP48S65, KP48S72, KP48V45, KP48V75, KP53S15, KP53S17, KP53S25, KP53S35, KP53S65, KP53V25, |

|KP53V35, KP53V45, KP53V75, KP53XBR45, KP61S35, KP61S65, KP61V25, KP61V35, KP61V45, KP61V75, KP61XBR48 |

| |

|Subject |

|UP DATE OF THE NVM JIG I/M, GEN SB31 |

| |

SYMPTOMS

If the need should arise that a circuit board needs to be replaced, It might contain an EEPROM. If the EEPROM data is not written into the EEPROM of the replacement board all the service or customer adjustments will be lost. Example: Convergence  adjustments. This will then require additional time to re-converge a projection TV.

 

RESOLUTION

Refer to SB GENTVP E08921219 for NVM Jig connections. Also refer to the NVM Instruction Manual for operating instructions E16415167 or TV SB449. The I/M will not address all chassis since it was written prior to RA-6 and DA4 chassis. The SB  E08921219 contains the settings for all chassis. 

|KP41T65 |

| |

|Subject |

|Two types of CRTs Used |

| |

SYMPTOMS

Two types of CRTs Used

RESOLUTION

If you need to replace the CRT please refer to the chart below for the correct CRT needed.

CRT Serial Number Range 9000001-9018822

Red 8-733-539-05

Blue 8-733-519-05

Green 8-733-537-05

Serial Number Range 9500001-9534348

Red A-1501-367-A 

Blue A-1501-369-A

Green A-1501-372-A

NOTE: Due to the CRT change some boards were also changed. Please see the

attached SB below before ordering any boards. 

SUPPORTING DOCUMENTS AND GRAPHICS

|[pic] |

|Name: SB400R1.pdf |

|Description: SB400R1 |

| |

|KP41T65 |

| |

|Subject |

|Unit in shutdown |

| |

SYMPTOMS

Unit is dead. 

CAUSE

No HV, TV just clicks. Found B+ voltage 135v. Source reading 10v and diode D655 getting hot. Disconnect 220v source to CB PCB and HV restored.

Found shorted video IC761. Replaced and solved problem.

 

RESOLUTION

No HV, TV just clicks. Found B+ voltage 135v. Source reading 10v and diode D655 getting hot. Disconnect 220v source to CB PCB and HV restored.

Found shorted video IC761. Replaced and solved problem.

|Part Number |Reference Number |Description |

|875943439 |314 |CB Board |

|KP41T65, KP46C65, KP48S65, KP48S65R, KP48V45, KP48V75, KP48V75, KP53S65, KP53V45, KP53V75, KP53V75, KP61S35, |

|KP61S65, KP61V45, KP61V75, KP61V75 |

| |

|Subject |

|Repeat failures of the audio amplifier |

| |

SYMPTOMS

We are having a continuing problem with the RA-2 chassis models. We get a no audio situation and find the Audio Amp TA8216H (IC404) shorted and PS401 open. We replace both components and the unit works fine for anywhere from 3 to 6 months.

 

RESOLUTION

You assistance is need to obtain the necessary information to find the solution to this failure.. Please contact your Tech Rep with the information required below.

The Vcc of audio amp may be higher than expected.

Vcc is provided from PIT but no  regulator in this line so the voltage varies by a variation of PIT winding. To verify that we want to know the voltage of Vcc.

Please measure the voltage between pin 9(Vcc) and pin 3(GND) of IC404. It's supposed to be around 30V. If our assumption  is correct then additional diode in Vcc line will help an IC404 failure. Design will determine type of diode and the location of the insertion with the information supplied from the servicers.

|Part Number |Reference Number |Description |

|8-759-168-24 |IC404 |Audio Amp TA8216H |

|1-532-984-11 |PS401 |IC 2A/90V |

 

|KP41T65, KP46C65, KP48S65, KP48V75, KP53S65, KP53V75, KP61S65, KP61V75 |

| |

|Subject |

|Repeat failures of the audio amplifier |

| |

SYMPTOMS

We are having a continuing problem with the RA-2A chassis models. We get a no audio situation and find the Audio Amp TA8216H (IC404) shorted and PS401 open. We replace both components and the unit works fine for anywhere from 3 to 6 months.

 

RESOLUTION

Your assistance is needed to obtain the necessary information to find the solution to this failure. Please contact your Tech Rep with the information required below.

The Vcc of audio amp may be higher than expected.

Vcc is provided from PIT but no regulator in this line so the voltage varies by a variation of PIT winding. To verify that we want to know the voltage of Vcc.

Please measure the voltage between IC404/pin 9 (Vcc) and pin 3 (GND) of IC404 or IC403 Audio Amp . It's supposed to be around 30V. If our assumption is correct then additional diode in Vcc line will help an IC404 failure. Design will determine type of diode and the location of the insertion with the information supplied from the servicers.

NOTE: Since we never received the requested information from the field no diode or circuit mod was created for this continuing failure. The information requested would have giving the engineering the details they needed to confirm there opinion that the voltage might be too  high but with no feedback they could not tell if their guess was correct or not.

 

|Part Number |Reference Number |Description |

|8-759-168-24 |IC404 |Audio Amp TA8216H |

|1-532-984-11 |PS401 |IC 2A/90V |

|KP41T15, KP41T25, KP41T35, KP41T65, KP43HT20, KP43T70, KP43T75, KP43T90, KP46C36, KP46C65, KP46C70, KP46S15, |

|KP46S25, KP46V25, KP46V35, KP48S35, KP48S65, KP48S65R, KP48S70, KP48S72, KP48S72, KP48S75, KP48V45, KP48V75, |

|KP48V80, KP48V85, KP48V90, KP51HW40, KP53HS20, KP53HS30, KP53N74, KP53S15, KP53S25, KP53S35, KP53S65, KP53S70, |

|KP53S75, KP53V25, KP53V35, KP53V45, KP53V75, KP53V80, KP53V85, KP53V90, KP53XBR45, KP53XBR4CT, KP57HW40, |

|KP57XBR10W, KP61HS20, KP61HS30, KP61S65, KP61S70, KP61S75, KP61V25, KP61V35, KP61V45, KP61V75, KP61V80, KP61V85, |

|KP61V90, KP61XBR48, KP65XBR10W |

| |

|Subject |

|Focus Block Part Change |

| |

SYMPTOMS

The original Focus Block is no longer available. 

RESOLUTION

If the Focus Block should need to be replaced the new sub P/N 1-223-925-31 should be used. The wire connections will be difference. See the diagram below for proper wiring.

Description Former P/N New P/N

Focus Block  1-223-925-11 1-223-925-31

Focus Block 1-223-925-12 1-223-925-31

Focus Block 1-223-925-81 1-223-925-31

The -51 should sub to the -61 and has 11 connections. They should not sub to the -31 or  -71 which have 10 connections. The -31 and -71 differ in the value of the resistors and should not sub as long as both are available.

 

SUPPORTING DOCUMENTS AND GRAPHICS

|[pic] |

|Name: sb555.pdf |

|Description: Focus Block diagram |

|Size: 16226 bytes |

| |

|KP41T65, KP46C65, KP48S65, KP48V75, KP53S65, KP53V75, KP61S65, KP61V75 |

| |

|Subject |

|Excessive red on picture |

| |

SYMPTOMS

Excessive red on picture 

CAUSE

Red drive too high. Red G2 voltage cannot be adjusted properly. Running red G2 through its normal range causes red to jump from blanked to retrace. 

RESOLUTION

Replaced C315 red S/H cap. Cap measured OK with capacitor checker, but substituting C315 resolved the problem. Cap was causing excessive red drive.

Located at IC301/pin 19. 

|Part Number |Reference Number |Description |

|113049500 |C315 |0.1UF 50V Film |

|KP41T65 |

| |

|Subject |

|CRT and board P/N change |

| |

SYMPTOMS

CRT and board P/N change

RESOLUTION

Please see the attached Supplement. 

SUPPORTING DOCUMENTS AND GRAPHICS

|[pic] |

|Name: Suppleme.pdf |

|Description: Supplement1 |

| |

|KP41T65, KP46C65, KP48S65, KP53S65, KP61S65 |

| |

|Subject |

|PN for C514 100pf and 680pf at 2kv |

| |

SYMPTOMS

The part number for C514 is not provided in the G board parts listing, because it is one of those selected values, per HV adjustment procedures on page 45. The values may be 100, 390, or 680 pf at 2KV. Need the P/N for the 100PF and the 680PF at 2kv.

 

RESOLUTION

The P/N are:

680pf /2kv 1-162-116-00

100pF/2kv 1-107-444-11 ceramic disc cap

|KP46C65 |

| |

|Subject |

|CONTROL DOOR P/N CHANGE, X-403-445-62 |

| |

SYMPTOMS

P/N 4-057-605-01, control door subs to NLA. 

RESOLUTION

Order the control panel assy per the following X-403-445-62 

|KP46C65 |

| |

|Subject |

|PART NUMBER ANODE & FOCUS LEAD |

| |

SYMPTOMS

What are the part numbers for the anode and focus leads? 

RESOLUTION

Anode 1-779-095-21

Focus Lead 1-900-231-42 

|KP46C65 |

| |

|Subject |

|DEAD, R610 |

| |

SYMPTOMS

Dead. 

RESOLUTION

Found R610 open on the G Board. 

|Part Number |Reference Number |Description |

|1-247-887-00 |R610 |220K 1/4W |

|KP46C65 |

| |

|Subject |

|DEAD, R614 |

| |

SYMPTOMS

Dead. 

RESOLUTION

Found R614 on the G Board was defective. 

|Part Number |Reference Number |Description |

|1-247-887-00 |R614 |220K 1/4W RESISTOR |

|KP48S65, KP61S65 |

| |

|Subject |

|P/N FOR IC5052 INCORRECT, 8-759-533-89 |

| |

SYMPTOMS

P/N for IC-5052 in the S/M 8-759-487-47 comes up no longer available in the system. 

RESOLUTION

The correct P/N is 8-759-533-89. 

|Part Number |Reference Number |Description |

|8-759-533-89 |IC5052 |SDA9288X-B121 |

|KP48S65 |

| |

|Subject |

|DEAD, IC601, R608, D662 |

| |

SYMPTOMS

Dead. 

RESOLUTION

Found IC601, R608, and D662 defective on the G Board. 

|Part Number |Reference Number |Description |

|8-719-991-33 |D662 |ISS133T-77 |

|8-729-041-12 |IC601 |MX0841AB-F |

|1-202-933-61 |R608 |FUSE 0.1 OHM 1/2W RESISTOR |

|KP48S65 |

| |

|Subject |

|NO PICTURE, T504 |

| |

SYMPTOMS

No Picture. 

RESOLUTION

Found T504 defective on the G: Board. 

|Part Number |Reference Number |Description |

|1-453-238-11 |T504 |FBT |

|KP48S35, KP48S35, KP48S35, KP48S65 |

| |

|Subject |

|NO VERTICAL, PS601 & PS602 |

| |

SYMPTOMS

No vertical. 

RESOLUTION

Found PS601 & PS602 open on the G Board. 

|Part Number |Reference Number |Description |

|1-533-597-21 |PS601 |LINK IC |

|1-533-597-21 |PS602 |LONK IC |

|KP48S65 |

| |

|Subject |

|POOR CONVERGENCE, IC803. |

| |

SYMPTOMS

Poor convergence. 

RESOLUTION

Replaced IC803 on the G Board. 

|Part Number |Reference Number |Description |

|8-759-183-37 |IC1803 |Shading Amp. |

|KP53S65 |

| |

|Subject |

|POOR PICTURE, MIRROR BROKEN |

| |

SYMPTOMS

Poor picture. 

RESOLUTION

Broken mirror. 

|Part Number |Reference Number |Description |

|4-048-181-01 |80 |MIRROR |

|KP53S65 |

| |

|Subject |

|P/N FOR IC5052 INCORRECT, 8-759-533-89. |

| |

SYMPTOMS

P/N for IC-5052 in the S/M 8-759-487-47 comes up no longer available in the system. 

RESOLUTION

The correct P/N is 8-759-533-89. 

|KP53S65, KP53V75 |

| |

|Subject |

|DAMAGED PIX TUBES |

| |

SYMPTOMS

A dab of what appears to be a clear silicon compound is applied to the junction of the CRT pins and sockets, to prevent the C boards from getting loose, it seems like the new models are receiving an excessive application of this compound making it very difficult to remove the C boards for service. When tech use a blade to cut exposed portion, enough of this compound has penetrated in front of the socket, preventing a gentle separation from the tube causing the frequent rupture of the CRT tip.

HQ:  Pittsburgh will reduce this compound to prevent this damage. 

SYMPTOMS

CRT Board very hard to remove causing damage to the CRT. 

RESOLUTION

We continue to investigate this issue

|KP53S65 |

| |

|Subject |

|DARK OR NO PICTURE, R586 |

| |

SYMPTOMS

Dark or no picture. -Found R586 on the G Board defective. Located off FBT/pin4 (200V) 

RESOLUTION

We continue to investigate this issue

|Part Number |Reference Number |Description |

|1-206-292-11 |R586 |1 OHM 1W |

|KP53S65 |

| |

|Subject |

|DEAD, T504 & Q502 |

| |

SYMPTOMS

Dead. 

RESOLUTION

FBT (T504) and Q502 defective on the A Board. 

|Part Number |Reference Number |Description |

|8-729-024-05 |Q502 |2SD2348 |

|1-453-238-11 |T504 |FBT |

|KP53S65 |

| |

|Subject |

|DEAD, T603 |

| |

SYMPTOMS

Dead. 

RESOLUTION

Replaced defective T603 on the G Board. 

|Part Number |Reference Number |Description |

|1-423-665-11 |T603 |POWER TRANSFORMER |

|KP53S65 |

| |

|Subject |

|IK BLANKING STANDBY LED FLASHING, D763 |

| |

SYMPTOMS

While in Ik blanking the screen would intermittently flash on and off with a bright cyan raster about every 15 seconds, or it might just stay blank. All three Ik pulses looked normal. Sound was normal. 

RESOLUTION

All three Ik pulses looked normal. Sound was normal.

Replace D763 10v 1/2 watt zener located off of IC761/pin 5 on the Blue CRT drive board. For testing purposes, lift one end of diode to see if restores operation. Our diode tested good with an ohm meter. This same diode is used on red & green CRT boards, D708 and D733. Lifting one end of D763 doesn't correct problem, you can try this same test for D708 and D733. 

|Part Number |Reference Number |Description |

|871911017 |D763 |RD1OESB2 |

|KP53S65 |

| |

|Subject |

|INTERMITTENT CONVERGENCE, IC007 |

| |

SYMPTOMS

Intermittent Convergence. 

RESOLUTION

Replaced IC007 on the A Board. 

|Part Number |Reference Number |Description |

|8-759-518-23 |IC007 |EEPROM |

|KP53S65 |

| |

|Subject |

|POOR PIN, D528 |

| |

SYMPTOMS

Poor pincushion. 

RESOLUTION

Found D528 located on IC501/pin1 defective on the G Board. 

|Part Number |Reference Number |Description |

|8-719-923-86 |D528 |MTZJ-T-77-15 |

|KP53S65 |

| |

|Subject |

|SHUTS DOWN, X5051 |

| |

SYMPTOMS

Unit shuts down. 

RESOLUTION

Replaced X5051 on the PT Board. 

|Part Number |Reference Number |Description |

|1-760-095-21 |X5051 |CRYSTAL |

|KP53S65 |

| |

|Subject |

|SNOWY PICTURE, TUNER |

| |

SYMPTOMS

Snowy picture. 

RESOLUTION

Replaced the tuner on the A Board. 

|Part Number |Reference Number |Description |

|8-598-340-00 |TU1101 |TUNER |

|KP53S65 |

| |

|Subject |

|VERTICAL POSITION INCORRECT, C337 |

| |

SYMPTOMS

Vertical position incorrect. 

RESOLUTION

Found C337 on the A Board defective. 

|Part Number |Reference Number |Description |

|1-126-960-11 |C337 |1UF 50V |

|KP53S65 |

| |

|Subject |

|blue off center |

| |

SYMPTOMS

Blue was off center by two inches and centering could not be adjusted.

CAUSE

IC804 on the G board was defective.

 

RESOLUTION

IC804 on the G board was defective.

|Part Number |Reference Number |Description |

|875946479 |IC804 |B CONV. |

|KP61S65 |

| |

|Subject |

|INTERMITTENT SHUTDOWN, CN8007 |

| |

SYMPTOMS

Intermittent shutdown. 

RESOLUTION

Found cold solder joint on CN8007. Resoldered CN8007 on the D Board. 

|KP61S65 |

| |

|Subject |

|MIRROR P/N INCORRECT, 4-058-643-01 |

| |

SYMPTOMS

The part number for the mirror, Ref 111, listed on page 91 of the Service Manual is incorrect. 

RESOLUTION

The correct part number is 4-058-643-01. 

|KP61S65 |

| |

|Subject |

|SCREEN ACCESSORY |

| |

SYMPTOMS

Which model do the SCN-61X2 Fit? 

RESOLUTION

This is for the KP-61S65. 

|KP61HS10, KP61S35, KP61S65, KP61S70, KP61S75, KP61V15, KP61V25, KP61V35, KP61V45, KP61V80, KP61V85, KP61XBR200, |

|KP61XBR300, KP61XBR38 |

| |

|Subject |

|Screen No Longer Available |

| |

SYMPTOMS

Screens No Longer Available

(L) 4-040-124-11

(F) 4-040-123-11

(L) 4-070-283-11

(F) 4-066-082-01 

RESOLUTION

If one of the screens is No Longer Available then it is recommended to replace both Fresnel and Lenticular with the P/Ns below to achieve satisfactory result.

Fresnel 4-084-704-01

Lenticular 4-070-283-01

|Model KP41T65: Features |

|[pic] |

| |PEDISTAL CLAMP YES |

| |AUTO WHITE BAL YES |

| |BRIGHTNESS 720 FT LAMBERTS |

| |COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN |

| |DYNAMIC FOCUS YES |

| |DYNAMIC CRT DYNAMIC PICTURE PROCESSOR |

| |SHADING CIRC YES |

| |VELOCITY MOD YES |

| |PROTECT SCREEN BUILT-IN HIGH CONTRAST PROTECTIVE SCREEN |

| |MTS YES |

| |MATRIX SURROUND YES |

| |AUDIO POWER 12 WATTS X 2 |

| |SPEAKER ON/OFF YES |

| |PIP YES |

| |PIP FREEZE FREEZE MEMO |

| |CHANNEL INDEX 12 CHANNELS |

| |MULTI-LANGUAGE ENGLISH,SPANISH,FRENCH |

| |FAVORITE CHANEL 5 CHANNEL |

| |CAPTION VISION YES |

| |CHANNEL CAPTION YES |

| |VIDEO LABEL YES |

| |PROGRAM TIMER YES |

| |SLEEP 30,60,90 MINUTES |

| |JUMP YES |

| |SA-VA CONTROL YES |

| |XDS EXTENDED DATA SERVICE |

| |CHANNEL BLOCK YES |

| |PROGRAM PALETTESTANDARD,MOVIE,SPORTS |

| |COLOR TEMP. TRINITONE COLOR TEMPERATURE ADJUSTMENT |

| |BRIGHTVIEW DUAL COMPONENT SCREEN |

| |GAMMA COMPENSATYES |

| |VIEWING ANGLE 130/55 |

| |VIDEO AMPLIFIERWIDEBAND |

| |CHANNEL MAGIC 8 CHANNELS |

| |CONV ADJUSTMENTWITH REMOTE |

|Model KP41T65: Specifications |

|[pic] |

|CHANNEL COVER |181 CHANNEL |

|TUNING SYSTEM |EXPRESS TUNING SYSTEM ( 181 CHANNEL ) |

|PROJECTION LENS |MICROFOCUS LENS SYSTEM |

|INPUT |2 REAR AUDIO/VIDEO INPUTS, 1 S-VIDEO |

|INPUTS |FRONT AUDIO/VIDEO INPUTS WITH S-VIDEO |

|ANT INPUT |75 OHMS |

|OUTPUTS |VARIABLE/FIXED AUDIO OUTPUTS |

|OUTPUTS |MONITOR |

|WEIGHT |122 LBS |

|DIMENSIONS |37 1/2 X 40 1/4 X 23 3/4 (W,H,D) |

|REMOTE CONTROL |RM-Y136A |

|COMB FILTER |3 LINE DIGITAL COMB FILTER |

|VIDEO PROCESSOR |BI-POLAR VIDEO PROCESSOR |

|AUDIO POWER |24 WATT AUDIO POWER |

|ENERGY STAR |ENERGY STAR COMPLIANT |

|S VIDEO |REAR S VIDEO INPUT |

|S OUTPUT |NO |

|Model KP46C65: Specifications |

|[pic] |

|CHANNEL COVER |VHF: 2-13, UHF: 14-69, CATV 1-125 |

|PROJ SYSTEM |3 PICTURE TUBES, 3 LENSES |

|PROJECTION LENS |HIGH PERFORMANCE, LARGE DIA HYBRID LENS F 1.1 |

|PICTURE BRIGHT |7" HI-BRIGHTNESS MONOCHROME TUBES |

|OPTIM VIEW AREA |HORIZ: 6 FT., VERT: 6 FT 20 DEGREES L/R |

|INPUT |A/V W S-VIDEO, VIDEO/AUDIO 2, A/V W/S-VIDEO |

|ANT INPUT |75 OHM |

|OUTPUTS |AUDIO OUT PHONO JACKS, IMPEDANCE: 5KILOHMS |

|OUTPUTS |MONITOR OUT: VIDEO/AUDIO |

|SPEAKER |FULL RANGE 100 MM (3.9 IN) DIA |

|PWR REQUIREMENT |120V, 60 HZ |

|PWR CONSUMPTION |165 WATTS, STANDBY MODE: 3 WATTS |

|WEIGHT |143 LBS 5 0Z (65 KG) |

|DIMENSIONS |42 X 51 1/2 X 22 1/4" (1066 X 1306 X 563MM) |

|REMOTE CONTROL |RMY136A |

|AUDIO POWER |SPEAKER OUTPUT: 15 W X 2 |

|ENERGY STAR |COMPATIBLE |

|S VIDEO |YES |

|Model KP48S65: Features |

|[pic] |

| |PEDISTAL CLAMP YES |

| |AUTO WHITE BAL YES |

| |BRIGHTNESS 550 FT LAMBERTS |

| |COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN |

| |DYNAMIC FOCUS YES |

| |DYNAMIC CRT DYNAMIC PICTURE PROCESSOR |

| |SHADING CIRC YES |

| |VELOCITY MOD YES |

| |PROTECT SCREEN SCN48X2 ( OPTIONAL ) |

| |MTS YES |

| |MATRIX SURROUND YES |

| |AUDIO POWER 12 WATTS X 2 |

| |SPEAKER ON/OFF YES |

| |PIP YES |

| |PIP FREEZE SNAP SHOT SCREEN FREEZE |

| |CHANNEL INDEX 12 CHANNELS |

| |MULTI-LANGUAGE ENGLISH,SPANISH,FRENCH |

| |FAVORITE CHANEL 5 CHANNEL |

| |CAPTION VISION YES |

| |CHANNEL CAPTION YES |

| |VIDEO LABEL YES |

| |PROGRAM TIMER YES |

| |SLEEP 30,60,90 MINUTES |

| |JUMP YES |

| |SA-VA CONTROL YES |

| |XDS YES |

| |CHANNEL BLOCK YES |

| |PROGRAM PALETTEPROGRAM PALLETTE (STANDARD,MOVIE,SPORTS) |

| |COLOR TEMP. HIGH,MEDIUM,NTCS STANDARD |

| |MIRROR FIRST SURFACE MIRROR |

| |BRIGHTVIEW DUAL COMPONENT SCREEN |

| |GAMMA COMPENSATYES |

| |VIEWING ANGLE 130/55 |

| |VIDEO AMPLIFIERWIDEBAND |

| |CHANNEL MAGIC 8 FAVORITE CHANNELS |

| |CONV ADJUSTMENTWITH REMOTE |

|Model KP48S65: Specifications |

|[pic] |

|CHANNEL COVER |181 CABLE COMPATIBLE |

|PROJECTION LENS |MICROFOCUS LENS SYSTEM |

|PICTURE BRIGHT |550 FT LAMBERTS |

|INPUT |2 REAR AUDIO/VIDEO INPUTS |

|INPUTS |1 FRONT AUDIO/VIDEO INPUT WITH S-VIDEO |

|ANT INPUT |75 OHMS |

|OUTPUTS |VARIABLE/FIXED AUDIO OUTPUT |

|OUTPUTS |MONITOR OUTPUT AND CONTROL S OUTPUT |

|PWR REQUIREMENT |120V, 60 HZ |

|PWR CONSUMPTION |165 W MAX, 2.5 STANDBY |

|WEIGHT |148 LBS APPROX. |

|DIMENSIONS |43 5/8 X 52 5/8 X 22 1/2 (W,H,D) |

|CABINET |GRAY |

|REMOTE CONTROL |RMY 136A |

|COMB FILTER |3 LINE COMB FILTER CIRCUITRY |

|VIDEO PROCESSOR |ADVANCED VIDEO PROCESSOR |

|AUDIO POWER |12W X 2 |

|ENERGY STAR |COMPATIABLE |

|S VIDEO |FRONT AND BACK S VIDEO INPUTS |

|Model KP48S65R: Features |

|[pic] |

| |PEDISTAL CLAMP YES |

| |AUTO WHITE BAL YES |

| |BRIGHTNESS 550 FT LAMBERTS |

| |COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN |

| |DYNAMIC FOCUS YES |

| |DYNAMIC CRT DYNAMIC PICTURE PROCESSOR |

| |SHADING CIRC YES |

| |VELOCITY MOD YES |

| |PROTECT SCREEN SCN48X2 (INCLUDED) |

| |MTS YES |

| |AUDIO POWER YES |

| |SPEAKER ON/OFF 12 WATTS X 2 |

| |PIP YES |

| |PIP FREEZE YES |

| |CHANNEL INDEX SNAP SHOT SCREEN FREEZE |

| |MULTI-LANGUAGE 12 CHANNELS |

| |FAVORITE CHANEL ENGLISH,SPANISH,FRENCH |

| |CAPTION VISION 5 CHANNEL |

| |CHANNEL CAPTION YES |

| |VIDEO LABEL YES |

| |PROGRAM TIMER YES |

| |SLEEP YES |

| |JUMP 30,60,90 MINUTES |

| |SA-VA CONTROL YES |

| |XDS YES |

|Model KP48S65R: Specifications |

|[pic] |

|CHANNEL COVER |181 CABLE COMPATIBLE |

|PROJECTION LENS |MICROFOCUS LENS SYSTEM |

|PICTURE BRIGHT |550 FT LAMBERTS |

|INPUT |2 REAR AUDIO/VIDEO INPUTS, COMPONENT VIDEO |

|INPUTS |1 FRONT AUDIO/VIDEO INPUT WITH S-VIDEO |

|ANT INPUT |75 OHMS |

|OUTPUTS |VARIABLE/FIXED AUDIO OUTPUT |

|OUTPUTS |MONITOR OUTPUT AND CONTROL S OUTPUT |

|PWR REQUIREMENT |120V, 60 HZ |

|PWR CONSUMPTION |165 W MAX, 2.5 STANDBY |

|WEIGHT |148 LBS APPROX. |

|DIMENSIONS |43 5/8 X 52 5/8 X 22 1/2 (W,H,D) |

|CABINET |GRAY |

|REMOTE CONTROL |RMY 136A |

|COMB FILTER |3 LINE COMB FILTER CIRCUITRY |

|VIDEO PROCESSOR |ADVANCED VIDEO PROCESSOR |

|AUDIO POWER |12W X 2 |

|ENERGY STAR |COMPATIABLE |

|S VIDEO |FRONT AND BACK S VIDEO INPUTS |

|Model KP53S65: Features |

|[pic] |

| |PEDISTAL CLAMP YES |

| |AUTO WHITE BAL YES |

| |BRIGHTNESS 460 FT LAMBERTS |

| |COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN |

| |DYNAMIC FOCUS YES |

| |DYNAMIC CRT DYNAMIC PICTURE PROCESSOR |

| |SHADING CIRC YES |

| |VELOCITY MOD YES |

| |PROTECT SCREEN SCN53X2 (OPTIONAL) |

| |MTS YES |

| |MATRIX SURROUND YES |

| |AUDIO POWER 12 WATTS X 2 |

| |SPEAKER ON/OFF YES |

| |PIP YES |

| |PIP FREEZE FREEZE MEMO |

| |CHANNEL INDEX NONE |

| |MULTI-LANGUAGE ENGLISH,SPANISH,FRENCH |

| |FAVORITE CHANEL 5 CHANNEL |

| |CAPTION VISION YES |

| |CHANNEL CAPTION YES,CUSTOMIZED UP TO 12 CHANNELS |

| |VIDEO LABEL YES |

| |PROGRAM TIMER YES |

| |SLEEP 30,60,90 MINUTES |

| |JUMP YES |

| |SA-VA CONTROL YES |

| |XDS YES |

| |CHANNEL BLOCK YES |

| |PROGRAM PALETTEMOVIE, SPORTS, STANDARD |

| |COLOR TEMP. TRINITONE ADJ (HIGH/MEDIUM/NTSC STANDARD) |

| |BRIGHTVIEW DUAL COMPONENT SCREEN |

| |GAMMA COMPENSATYES |

| |VIEWING ANGLE 130/55 |

| |VIDEO AMPLIFIERWIDEBAND |

| |CHANNEL MAGIC 8 FAVORITE CHANNELS |

| |CONV ADJUSTMENTWITH REMOTE |

|Model KP53S65: Specifications |

|[pic] |

|CHANNEL COVER |181 CABLE COMPATIBLE |

|TUNING SYSTEM |EXPRESS TUNING SYSTEM (181 CHANNEL) |

|PROJECTION LENS |MICROFOCUS LENS SYSTEM |

|PICTURE BRIGHT |460 FT LAMBERTS |

|INPUT |2 RF INPUTS |

|INPUTS |FRONT AUDIO/VIDEO INPUTS WITH S-VIDEO |

|ANT INPUT |RF 75 OHM |

|OUTPUTS |VARIABLE/FIXED AUDIO OUTPUT |

|OUTPUTS |MONITOR OUTPUT AND CONTROL S OUTPUT |

|AUDIO/VID INPUT |1 A/V WITH S-VIDEO, 1 A/V ONLY |

|AUD/VID OUTPUT |MONITOR OUT, AUDIO FIXED/VARIABLE |

|PWR REQUIREMENT |120 V, 60 HZ |

|PWR CONSUMPTION |165 WATTS MAX/2.5 WATTS STANDBY |

|WEIGHT |153 LBS APPROX. |

|DIMENSIONS |48" X 55 5/8 X 24 1/4 (W,H,D) |

|CABINET |GRAY |

|REMOTE CONTROL |RM-Y136A |

|COMB FILTER |3 LINE DIGITAL COMB FILTER CIRCUITRY |

|VIDEO PROCESSOR |ADVANCED VIDEO PROCESSOR |

|AUDIO POWER |12 WATTS X 2 |

|ENERGY STAR |COMPLIANT |

|S VIDEO |FRONT/REAR S VIDEO INPUTS |

|Model KP61S65: Features |

|[pic] |

| |PEDISTAL CLAMP YES |

| |AUTO WHITE BAL YES |

| |BRIGHTNESS 380 FT LAMBERTS |

| |COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN |

| |DYNAMIC FOCUS YES |

| |DYNAMIC CRT DYNAMIC PICTURE PROCESSOR |

| |SHADING CIRC YES |

| |VELOCITY MOD YES |

| |PROTECT SCREEN SCN61X2 (OPTIONAL) |

| |MTS YES |

| |MATRIX SURROUND YES |

| |AUDIO POWER 12 WATTS X 2 |

| |SPEAKER ON/OFF YES |

| |PIP YES |

| |PIP FREEZE FREEZE MEMO |

| |CHANNEL INDEX 12 CHANNELS |

| |MULTI-LANGUAGE ENGLISH,SPANISH,FRENCH |

| |FAVORITE CHANEL 5 CHANNEL |

| |CAPTION VISION YES |

| |CHANNEL CAPTION YES |

| |VIDEO LABEL YES |

| |PROGRAM TIMER YES |

| |SLEEP 30,60,90 MINUTES |

| |JUMP YES |

| |SA-VA CONTROL YES |

| |XDS YES |

| |CHANNEL BLOCK YES |

| |PROGRAM PALETTEMOVIE, SPORTS, STANDARD |

| |COLOR TEMP. TRINITONE ADJ (HIGH/MEDIUM/NTSC STANDARD) |

| |BRIGHTVIEW DUAL COMPONENT SCREEN |

| |GAMMA COMPENSATYES |

| |VIEWING ANGLE 130/55 |

| |VIDEO AMPLIFIERWIDEBAND |

| |CHANNEL MAGIC 8 FAVORITE CHANNELS |

| |CONV ADJUSTMENTWITH REMOTE |

|Model KP61S65: Specifications |

|[pic] |

|CHANNEL COVER |181 CHANNEL CATV |

|TUNING SYSTEM |EXPRESS TUNING SYSTEM ( 181 CHANNEL ) |

|PROJECTION LENS |MICROFOCUS LENS SYSTEM |

|PICTURE BRIGHT |380 FT LAMBERTS |

|INPUT |2 RF INPUTS |

|INPUTS |1 FRONT/REAR A/V WITH S-VIDEO, 1 REAR A/V |

|ANT INPUT |75 OMHS |

|OUTPUTS |VARIABLE/FIXED AUDIO OUTPUT |

|OUTPUTS |MONITOR OUT |

|AUDIO/VID INPUT |2 REAR AND 1 FRONT AUDIO/VIDEO |

|SPEAKER |12W X 2 |

|PWR REQUIREMENT |120 V, 60 HZ |

|PWR CONSUMPTION |165 WATTS MAX/2.5 WATTS STANDBY |

|WEIGHT |269 LBS |

|DIMENSIONS |52 3/4 X 59 3/8 X 25 3/8 (W,H,D) |

|CABINET |DARK GRAY FINISH |

|REMOTE CONTROL |RM-Y136 |

|COMB FILTER |3 LINE COMB FILTER CIRCUITRY |

|VIDEO PROCESSOR |ADVANCED VIDEO PROCESSOR |

|ENERGY STAR |YES |

|S VIDEO |REAR S VIDEO INPUT, FRONT S-VIDEO INPUT |

|S OUTPUT |CONTROL S OUTPUT |

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download