AQA IGCSE Further Maths Revision Notes
[Pages:16]AQA IGCSE Further Maths Revision Notes
Formulas given in formula sheet:
Volume
of
sphere:
4 3
3
Surface area of sphere: 42
Volume
of
cone:
1 3
2
Curve surface area:
Area
of
triangle:
1 2
sin
Sine
Rule:
sin
=
sin
=
sin
Cosine Rule: 2 = 2 + 2 - 2 cos
Quadratic equation: 2 + + = 0 = -?2-4
2
Trigonometric Identities: tan sin
cos
sin2 + cos2 1
1. Number
Specification 1.1 Knowledge and use of numbers and the number system including fractions, decimals, percentages, ratio, proportion and order of operations are expected.
1.2 Manipulation of surds, including rationalising the denominator.
Notes
A few possibly helpful things:
If
:
=
:
(i.e.
the
ratios
are
the
same),
then
=
"Find the value of after it has been increased by %"
If say was 4, we'd want to ? 1.04 to get a a 4% increase.
Can
use
1
+
100
as
the
multiplier,
thus
answer
is:
(1 + 100)
"Show that % of is the same as % of "
GCSE recap:
100 ? = 100
100 ? = 100
Laws
of
surds:
?
=
and
=
But note that ? = not
Note also that ? = To simplify surds, find the largest square factor and put this
first:
12 = 43 = 23
75 = 253 = 53
52 ? 32 Note everything is being multiplied here. Multiply surd-ey things and non surd-ey things separately. = 15 ? 2 = 30
8 + 18 = 22 + 32 = 52 To `rationalise the denominator' means to make it a non-
surd. Recall we just multiply top and bottom by that surd:
6
3
6 3
?
3 3
=
63 3
=
23
The new thing at IGCSE FM level is where we have more
complicated denominators. Just multiply by the `conjugate':
this just involves negating the sign between the two terms:
3
3 6 + 2 3(6 + 2)
?
=
6 - 2
6 - 2 6 + 2
2
A trick to multiplying out the denominator is that we have
the difference of two squares, thus (6 - 2)(6 + 2) =
6 - 4 = 2 (remembering that 6 squared is 6, not 36!)
23-1 23-1 ? 33-4 = (23-1)(33-4) =
33+4
33+4 33-4
27-16
18-33-83+4 11
=
22-113 11
=
2
-
3
What can go ugly
I've seen students inexplicably reorder the terms in the denominator before they multiply by the conjugate, e.g.
(2 + 3)(3 - 2) Just leave the terms in their original order!
I've also seen students forget to negate the sign, just doing (2 + 3)(2 + 3) in the denominator. The problem here is that it won't rationalise the denominator, as we'll still have surds!
Silly error: 66 2 33
(rather than 36)
1
2. Algebra
Specification 2.2 Definition of a function
2.3 Domain and range of a function.
Notes
A function is just something which takes an input and uses some rule
to produce an output, i.e. () =
You need to recognise that when we replace the input with some
other expression, we need to replace every instance of it in the
output, e.g. if () = 3 - 5, then (2) = 32 - 5, whereas ()2 = (3 - 5)2. See my Domain/Range slides.
e.g. "If () = 2 + 1, solve (2) = 51
22 + 1 = 51 = ?5
The domain of a function is the set of possible inputs.
The range of a function is the set of possible outputs.
Use to refer to input and () to refer to output. Use "for all" if any
value possible. Note that < vs is important.
() = 2 Domain: for all Range: for all ()
() = 2 Domain: for all Range: () 0
() = Domain: 0 Range: () 0
() = 2 Domain: for all Range: () > 0
() = 1
Domain: for all except 0.
Range: for all () except 0.
() = 1
-2
Domain: for all except 2 (since we'd be dividing by 0)
Range: for all () except 0 (sketch to see it)
() = 2 - 4 + 7 Completing square we get ( - 2)2 + 3
The min point is (2,3). Thus range is () 3
You can work out all of these (and any variants) by a quick sketch and
observing how and values vary.
Be careful if domain is `restricted' in some way.
Range if () = 2 + 4 + 3, 1
When = 1, (1) = 8, and since () is increasing after
this value of , () 8.
To find range of trigonometric functions, just use a suitable
sketch, e.g. "() = sin()" Range: -1 () 1
However be careful if domain is restricted:
"() = sin() , 180 < 360". Range: -1 () 0
(using a sketch)
For `piecewise function',
fully sketch it first to find
range.
"The function () is
defined for all :
4 () = { 2
< -2 -2 2
12 - 4 > 2 Determine the range of ()."
From the sketch it is clear
() 4
You may be asked to construct a function given information
about its domain and range.
e.g. " = () is a straight line. Domain is 1 5 and
range is 3 () 11. Work out one possible expression
for ()."
We'd have this domain and range if line passed through
points (1,3) and (5,11). This gives us () = 2 + 1
What can go ugly
Not understanding what (2) actually means. Not sketching the graph! (And hence not being able to visualise what the range should be). This is particularly important for `piecewise' functions. Not being discerning between < and in the range. e.g. For quadratics you should have but for exponential graphs you should have ................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- aqa igcse further maths revision notes
- interactive learner guide
- cambridge igcse mathematics revision guide
- syllabus cambridge igcse mathematics 0580
- gcse exam questions on plans and elevations
- higher problem solving questions
- correlation coefficient worksheet
- year 7 revision sheets papplewick school
- vocabulary book word version pearson qualifications
- arc length and sector area exam questions web maths
Related searches
- igcse physics revision notes pdf
- igcse math revision notes pdf
- igcse maths revision notes
- igcse maths revision worksheets pdf
- igcse revision notes pdf
- biology igcse revision notes pdf
- igcse chemistry revision notes pdf
- gcse maths revision notes pdf
- igcse maths revision guide pdf
- igcse revision notes pdf economics
- biology igcse revision notes 2016
- igcse biology revision notes pdf