LIGHTING SECURITY VIPER S SERIES S Le

SECURITY

LIGHTINGTM

SPECIFICATIONS

design . performance . technology

VIPER S SERIES Small Viper Luminaire

PRODUCT IMAGE(S)

OPTICS

Intended Use: The Beacon Viper luminaire is available with a wide choice of different LED Wattage configurations and optical distributions designed to replace HID lighting up to 400W MH or HPS.

Construction: ? Manufactured with die cast aluminum. ? Coated with a polyester finish that meets

ASTM B117 corrosion test requirements and ASTM D522 cracking and loss of adhesion test requirements. ? External hardware is corrosion resistant. ? One piece optical cartridge system consisting of an LED engine, LED lamps, optics, gasket and stainless steel bezel. ? Cartridge is held together with internal brass standoffs soldered to the board so that it can be field replaced as a one piece optical system. ? Two-piece silicone and micro-cellular polyurethane foam gasket ensures a weather-proof seal around each individual LED.

Electrical: ? 100V through 277V, 50 Hz to 60 Hz (UNV), or

347V or 480V input. ? Power factor is .90 at full load. ? Dimming drivers are standard, but must

contact factory to request wiring leads for purpose of external dimming controls. ? Component-to-component wiring within the luminaire may carry no more than 80% of rated load and is certified by UL for use at 600VAC at 90?C or higher. ? Plug disconnects are certified by UL for use at 600 VAC, 13A or higher. 13A rating applies to primary (AC) side only. ? Fixture electrical compartment shall contain all LED driver components and shall be provided with a push-button terminal block for AC power connections. ? Surge protection - 20kA. ? Optional 7-pin ANSI C136.41-2013 twist-lock photo control receptacle available. Compatible with ANSI C136.41 external wireless control devices. ? LifeshieldTM Circuit - protects luminaire from excessive temperature. The device shall activate at a specific, factory-preset temperature, and progressively reduce power over a finite temperature range. Operation shall be smooth and undetectable to the eye. Thermal circuit is designed to "fail on", allowing the luminaire to revert to full power in the event of an interruption of its power supply, or faulty wiring connection to the drivers. The device shall be able to co-exist with other 0-10V control devices (occupancy sensors, external dimmers, etc.).

Controls/Options: ? Available with an optional passive infrared

(PIR) motion sensor capable of detecting motion 360? around the luminaire. When no motion is detected for the specified time, the Motion Response system reduces the wattage to factory preset level, reducing the light level accordingly. When motion is detected by the PIR sensor, the luminaire returns to full wattage and full light output. Please contact Beacon Products if project requirements vary from standard configuration. ? Available with Energeni for optional set dimming, timed dimming with simple delay, or timed dimming based on time of night (see products/energeni).

? In addition, Viper can be specified with SiteSyncTM wireless control system for reduction in energy and maintenance costs while optimizing light quality 24/7. For more details, see ordering information or visit: sitesync

Installation: ? Mounting options for horizontal arm, vertical

tenon or traditional arm mounting available. Mounting hardware included.

Finish: ? IFS polyester powder-coat electrostatically

applied and thermocured. IFS finish consists of a five stage pretreatment regimen with a polymer primer sealer and top coated with a thermoset super TGIC polyester powder coat finish.

? The finish meets the AAMA 2604 performance specification which includes passing a 3000 hour salt spray test for corrosion resistance and resists cracking or loss of adhesion per ASTM D522 and resists surface impacts of up to 160 inch-pounds.

Certifications/Ratings: ? DesignLights Consortium (DLC) qualified,

consult DLC website for more details:

? Certified to UL 1598, UL 8750 and CSA C22.2 No.250.0

? IDA approved

? This product is approved by the Florida Fish and Wildlife Conservation Commission. Separate spec available at:

Warranty: Five year limited warranty for more information visit: resources/warranty

DIMENSIONS

A B

4 1/8"

C

Front

A 21.75" (552 mm)

B

C

Weight:

16.75" 11.25 " 15.0 lbs

(425 mm) (286 mm) (6.8 kg)

MOUNTING OPTIONS

EPA .67 ft2

Side View

Rectangular Arm (A)

Accepts 2 3/8" OD tenon, min

4" long.

Side View 2-3/8" OD Slip Fitter (MAF)

18.75"

Back View

Back View 6.00"

6.63"

2-3/8" Adjustable Knuckle (K) limit to 45O tilt

22.25"

5.00"

2.38" 4x 0.50" 5.50"

6.00"

24.75"

Wall Bracket (WB)

7.75"

CERTIFICATIONS/LISTINGS

Web: 2100 Golf Road, Suite 460, Rolling Meadows, IL 60008-4704 Phone: 1-800-LIGHT IT, 1-800-544-4848, Fax: 847-279-0642 Copyright ?2016 Security Lighting, a division of Hubbell Lighting, Inc. All Rights Reserved. ? Specifications subject to change without notice. ? Printed in U.S.A. ? SL0001 08/17

AD Decorative Arm 0.56"

1" 4.88"

SECURITY

LIGHTINGTM

design . performance . technology

VIPER S SERIES Small Viper Luminaire

ORDERING INFORMATION ORDERING EXAMPLE: VPS/24L-55/4K7/4W/UNV/A/DBT/7PR-TL/GENI-04/BC

VPS

SERIES

LED ENGINE

CCT/CRI7

ROTATION

VOLTAGE

COLOR

OPTIONS

VPS Viper

24L-55 55W, LED array

36L-65 65W, LED array

36L-80 80W, LED array

48L-110 110W, LED array

60L-136 136W, LED array

3K7 3000K, 70 CRI 4K7 4000K, 70 CRI 5K7 5000K, 70 CRI

Leave blank for no rotation

L5 Optic rotation left

R5 Optic rotation right

DISTRIBUTION FR Type 1/Front Row

2 Type 2 3 Type 3 4 Type 4

UNV 120-277V 120 120V 208 208V 240 240V 277 277V 347 347V 480 480V

DBT Dark Bronze Textured BMT Black Matte Textured

PS Platinum Silver Smooth WHT White Textured

CC Custom Color (RAL#)

F Fusing BSP Bird Spikes

BC Backlight control (limited to Type 4W only)

4W Type 4 Wide 5QM Type 5QM

5R Type 5R (rectangular) 5W Type 5W (round wide)

HOUSE SIDE SHIELD ACCESSORIES HSS/VP-S/90-FB/XXX 90? shield front or back HSS/VP-S/90-LR/XXX 90? shield left or right HSS/VP-S/270-FB/XXX 270? shield front or back HSS/VP-S/270-LR/XXX 270? shield left or right

HSS/VP-S/360/XXX Full shield

(Replace XXX with notation for desired finish color) (Refer to page 5 for shield images)

MOUNTING ACCESSORIES VPL-AD-RPA3 2.4"-4.1" Round Pole Adapter for AD arm VPL-AD-RPA4 4.2"-5.3" Round Pole Adapter for AD arm

MOUNTING

A Rectangular Arm (formerly RA) for square or round pole

MAF Mast Arm Fitter (formerly SF2) for 2-3/8" OD horizontal arm

K Knuckle (formerly PK2) limit to 45O tilt or 2-3/8" OD horizontal arm or vertical tenon

WB Wall Bracket

AD Universal Arm for square pole

AD3 Universal Arm for 2.4"-4.1" round pole

AD4 Universal Arm for 4.2" -5.3" round pole

AD5 Universal Arm for 5.5" -5.9" round pole

AD6 Universal Arm for 6.0"-6.5" round pole

CONTROL OPTIONS

7PR 7-Pin Receptacle only (shorting cap, photo control, or wireless control provided by others)

7PR-SC 7-Pin Receptacle w/Shorting Cap

7PR-TL 7-Pin Receptacle w/Twist Lock photo control

SCP/_F1,2,6 Programmable Occupancy Sensor w/ daylight control (120-277 volts only)

WSP/_F1,2 WASP Occupancy Sensor w/ daylight control (347 or 480 volts only)

GENI-XX3 ENERGENI

SWP1,4 SiteSync Pre-Commission

SWPM1,2,4 SiteSync Pre-Comm w/ Sensor

VPL-AD-RPA5 5.5"-5.9" Round Pole Adapter for AD arm VPL-AD-RPA6 6.0"-6.5" Round Pole Adapter for AD arm

Accessories and Services (Ordered Separately)

Catalog Number Description

PRECOMMISSIONED SITESYNC ORDERING INFORMATION: When ordering a fixture with the SiteSync lighting control option, additional information will be required to complete the order. The SiteSync Commissioning Form or alternate schedule information must be completed. This form includes Project location, Group information, and Operating schedules. For more detailed information please visit products/sitesync/ or contact Hubbell Lighting tech support at (800) 345-4928.

SiteSync fixtures with Motion control (SWPM) require the mounting height of the fixture for selection of the lens.

Examples: VPS/24L-55/4K7/3/UNV/A/DBT/SWP/ VPS/24L-55/4K7/3/UNV/A/DBT/SWPM-40F/

SiteSync only SiteSync with Motion Control

1 Not available with other wireless control or sensor options 2 Specify mounting height; 8=8' or less, 40=9' to 40' 3 Specify routine setting code (example GENI-04). See ENERGENI brochure and instructions for setting table and options. Not available

with sensor or SiteSync options. 4 Specify group and zone at time of order. See sitesync for further details. Order at least one SiteSync interface

Accessory SWUSB or SWTAB. Each option contains SiteSync License, GUI, and Bridge Node 5 Only available with 1A, 2, 3, 4, 4W and 5R distributions 6 Order at least one SCP-REMOTE per project location to program and control 7 This product is approved by the Florida Fish and Wildlife Conservation Commission. Separate spec available at:



SCP-REMOTE SWUSB*

Remote control for SCP/_F option. Order at least one per project to program and control.

SiteSync loaded on USB flash drive (Windows based only)

SWTAB* SWBRG+

SiteSync Windows Tablet SiteSync Wireless Bridge Node

* When ordering with SiteSync, one of the interface options must be chosen and ordered separately. Each option contains the SiteSync License, GUI and Bridge Node.

+ If needed, an additional Bridge Node can be ordered.

LEFT ROTATED OPTIC

RIGHT ROTATED OPTIC

SiteSync Lighting Control is available from our most popular brands in a broad range of award-winning product families.

Web: 2100 Golf Road, Suite 460, Rolling Meadows, IL 60008-4704 Phone: 1-800-LIGHT IT, 1-800-544-4848, Fax: 847-279-0642 Copyright ?2016 Security Lighting, a division of Hubbell Lighting, Inc. All Rights Reserved. ? Specifications subject to change without notice. ? Printed in U.S.A. ? SL0001 08/17

SECURITY

LIGHTINGTM

design . performance . technology

VIPER S SERIES Small Viper Luminaire

PERFORMANCE DATA

# LED'S

DRIVE CURRENT (MILLIAMPS)

24

700 mA

36

560 mA

36

700 mA

48

700 mA

60

700 mA

SYSTEM WATTS

55W

65W

80W

110W

136W

5K (5000K nominal, 70 CRI)

4K (4000K nominal, 70 CRI)

3K (3000K nominal, 70 CRI)

DISTRIBUTION

TYPE

LUMENS LPW1 B U G LUMENS LPW1 B U G LUMENS LPW1 B U G

FR

6357 118 1 0 1 6486 120 1 0 1 5804 107 1 0 1

2

6132 114 1 0 1 6257 116 1 0 2 5599 104 1 0 1

3

6015 111 1 0 2 6137 114 1 0 2 5492 102 1 0 2

4

5921 110 1 0 2 6034 112 1 0 2 5400 100 1 0 2

4W

5406 100 1 0 2 6041 112 1 0 2 5406 100 1 0 2

5QM

6022 112 2 0 1 6145 114 2 0 1 5499 102 2 0 1

5R

6063 112 3 0 3 6187 115 3 0 3 5536 103 3 0 3

5W

5908 109 3 0 1 6028 112 3 0 1 5908 102 3 0 1

FR

7864 121 1 0 1 8041 124 1 0 1 7189 111 1 0 1

2

7586 117 1 0 2 7757 119 1 0 2 6934 107 1 0 2

3

7441 114 1 0 2 7609 117 1 0 2 6802 105 1 0 2

4

7317 110 1 0 2 7482 112 1 0 2 6688 100 1 0 2

4W

7325 113 1 0 2 7490 115 1 0 2 6696 103 1 0 2

5QM

7450 115 3 0 1 7618 117 3 0 1 6810 105 3 0 1

5R

7501 115 3 0 3 7670 118 3 0 3 6857 105 3 0 3

5W

7309 112 3 0 2 7473 115 3 0 2 6681 103 3 0 1

FR

9535 118 1 0 1 9730 120 1 0 1 8706 107 1 0 1

2

9197 114 1 0 2 9385 116 1 0 2 8398 104 1 0 2

3

9022 111 1 0 2 9206 114 1 0 2 8238 102 1 0 2

4

8871 110 1 0 2 9052 112 1 0 2 8100 100 1 0 2

4W

8881 110 1 0 3 9062 112 1 0 3 8109 100 1 0 2

5QM

9033 112 3 0 1 9217 114 3 0 1 8248 102 3 0 1

5R

9095 112 3 0 3 9280 115 3 0 3 8304 103 3 0 3

5W

8861 109 3 0 2 9043 112 3 0 2 8092 100 3 0 2

FR

12713 118 1 0 1 12973 120 2 0 1 11608 107 1 0 1

2

12263 114 2 0 2 12513 116 2 0 2 11197 104 2 0 2

3

12029 111 2 0 2 12275 114 2 0 2 10984 102 1 0 2

4

11828 110 1 0 3 12069 112 1 0 3 10800 100 1 0 2

4W

11841 110 5 0 5 12083 112 2 0 3 11841 110 1 0 3

5QM

12044 112 3 0 2 12290 114 3 0 2 10997 102 3 0 1

5R

12126 112 3 0 3 12374 115 3 0 3 11072 103 3 0 3

5W

11825 109 4 0 2 12057 112 4 0 2 10789 100 4 0 2

FR

15891 117 2 0 2 16216 120 2 0 2 14511 107 2 0 1

2

15329 113 2 0 2 15642 116 2 0 2 13997 103 2 0 2

3

15037 111 2 0 3 15344 113 2 0 3 13730 101 2 0 3

4

14784 109 1 0 3 15086 111 1 0 3 13500 100 1 0 3

4W

14802 109 2 0 3 15104 112 2 0 3 13515 100 2 0 3

5QM

15055 111 3 0 2 15362 114 3 0 2 13747 102 3 0 2

5R

15158 112 4 0 4 15469 114 4 0 4 13841 102 4 0 4

5W

14781 109 4 0 2 15083 111 4 0 2 13495 100 4 0 2

Web: 2100 Golf Road, Suite 460, Rolling Meadows, IL 60008-4704 Phone: 1-800-LIGHT IT, 1-800-544-4848, Fax: 847-279-0642 Copyright ?2016 Security Lighting, a division of Hubbell Lighting, Inc. All Rights Reserved. ? Specifications subject to change without notice. ? Printed in U.S.A. ? SL0001 08/17

SECURITY

LIGHTINGTM

PHOTOMETRICS

Type FR - Front Row/Auto Optic

Type 2

Type 5W

design . performance . technology

VIPER S SERIES Small Viper Luminaire

Type 3

Type 4

Type 4W

Type 5QM

Type 5R

1Lumen values are from photometric tests performed in accordance with IESNA LM-79-08. Data is considered to be representative of the configurations shown. Actual performance may differ as a result of end-use environment and application.

ELECTRICAL DATA NUMBER OF

# OF LEDS DRIVERS

24

2

36

1

48

1

60

1

DRIVE CURRENT

(mA) 700 mA

560 mA

700 mA

700 mA

700 mA

INPUT VOLTAGE

(V)

120 277 347 480 120 277 347 480 120 277 347 480 120 277 347 480 120 277 347 480

SYSTEM POWER (w) 55

65

80

110

136

CURRENT

(Amps)

0.5 0.2 0.2 0.1 0.65 0.28 0.22 0.16 0.7 0.3 0.2 0.2 0.9 0.4 0.3 0.2 1.1 0.5 0.4 0.3

PROJECTED LUMEN MAINTENANCE

AMBIENT

1TM-21-11

Calculated L70

TEMP.

0 25,000 50,000 60,000 100,000 (HOURS)

25?C / 77?C 1.00 0.97 0.95

0.95

0.92

>377,000

1 Projected per IESNA TM-21-11 Data references the extrapolated performance projections for the base model in a 25?C ambient, based on 10,000 hours of LED testing per IESNA LM-80-08.

DRILL PATTERN

Compatible with Pole drill pattern B4

4" Suggested distance from top

of pole

2.50"

?5/8" 2X ?5/16"

Rectangular Arm

?4" Pole ?5" Pole

?6" Pole

EPA Config. EPA

1

.67

2 @ 90? 1.06

2 @ 180? 1.34

Config. EPA 3 @ 120? 1.68 3 @ 90? 1.73

4 @ 90? 2.12

TENON TOP POLE BRACKET ACCESSORIES (Order Separately)

(2 3/8" OD tenon)

Catalog Number SETA2-XX1,2 RETA2-XX1,3 TETA2-XX1,2

Description Square tenon adapter (4 at 90 degrees) Round tenon adapter (4 at 90 degrees) Hexagonal tenon adapter (3 at 120 degrees)

1 Replace XX with color choice, eg.: DB for Dark Bronze 2 Only for use with AD mounting option 3 Only for use with AD3 mounting option

Web: 2100 Golf Road, Suite 460, Rolling Meadows, IL 60008-4704 Phone: 1-800-LIGHT IT, 1-800-544-4848, Fax: 847-279-0642 Copyright ?2016 Security Lighting, a division of Hubbell Lighting, Inc. All Rights Reserved. ? Specifications subject to change without notice. ? Printed in U.S.A. ? SL0001 08/17

SECURITY

LIGHTINGTM

HOUSE SIDE SHIELD FIELD INSTALL ACCESSORIES

design . performance . technology

VIPER S SERIES Small Viper Luminaire

ECORAHTSSI/VVP-ES/90A-FBR/XXMX 90? shield front or back (2 shields shown)

HSS/VP-S/90-LR/XXX 90? shield left or right (1 shield shown in left orientation)

HSS/VP-S/270-FB/XXX 270? shield front or back (1 shield shown in back orientation)

HSS/VP-S/270-LR/XXX 270? shield left or right (1 shield shown in right orientation)

ER AD ARM MOUNTING INSTRUCTIONS

Sliding nut block fits inside pole

HSS/VP-S/360/XXX Full shield (1 shield shown)

VIPER AD Arm

Round pole example RPA required only for attachment to round poles

Round pole adapter (when applicable)

Wireway cover

Shipping Package Contents:

o align top 1/2" hole with the pre-drilled holes in

Viper AD Arm

Block inside pole noting the side that is placed e wall.

Viper AD Arm Adapter Viper AD Arm Wireway Cover

Bolt with lock and flat washer through the botton

Sliding Nut Block Assembly

ghten into the lower nut on the Sliding Nut Block.

3 Hex Bolt with lock and flat washer through the cate and tighten into the top nut on the Sliding Nut

1/2-13 Bolts (2) 1/2 Split Washers (2)

h)nee1gpn/2oNt"lhueBet aoBanlltrodsmcaakidt.sW2Pa71hipe5n0otbse0fntt:ra-eGwllsb:leoows1d-lfwtt8.hhR0.arsoo0teua-ictLgducIh,GraSiAHntuyrTbmliitegIeTAhe,4tda1i6n-as80pgil0,yt.ecR0roo-5mall4nind4g-4M84e8a,dFo111aw0//x24s-:,-28F2IL44l07a6U-0t2U07NWN90C-8Ca0-6s4BB4h7u20uet4ttrotson(n2HH) eeaaddSSccrreeww(s1()2)

tive Arm overCAoDpyArrigmhtA?da2p0t1e6r SflueschuraitgyaLinigsht ttihneg, a division of Hubbell Lighting, Inc.

ngage ) ?-20

SthceremwaAstlialntRg2igd0heftttsa-libRlsseisnthetrrhoveuegdah.d?aVSpippteeerrc. DifieccaotiroantisvesubjecMt taotcehrainagle:wAitlhuomut innouticme.

?

Printed

in

U.S.A.

?

SL0001

08/17

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download