MIL-STD-105 – Sampling Procedures and Tables for ...
MIL-STD-105 ¨C Sampling Procedures and Tables for
Inspection by Attributes
Subject/Scope:
This publication establishes lot or batch sampling plans and procedures for inspection
by attributes. This publication shall not be "interpreted to supersede or conflict with any
contractual requirements. The words "accept", "acceptance", "acceptable", etc, refer
only to the contractor's use of the sampling plans contained in this standard and do not
imply an agreement by the Government to accept any product. Determination of
acceptability by the Government shall be as described in contractual documents. The
sampling plans described in this standard are applicable to AQL's of .01 percent or
higher and are therefore not suitable for applications where quality levels in the
defective parts per million range can be realized.
Keywords:
Inspection, plan, defect, product, defective, curve, percent, multiple, quality, acceptance, average, std,
procedure, mil, chart, sampling, process, size, standard, level, reject, critical, requirement, publication,
major, minor, acceptability, accepted, drawn, protection, special, specified, production, requirement,
defense, quality, military
Published:
5/10/1989
Text in blue boxes such as this one is instructional and is intended to assist you in understanding the document.
Text in red boxes such as this explains changes made to the document by The Wooden Crates Organization.
Red text has been added to the document or modifies the document since its final version was officially published.
Soft Conversion of Imperial to Metric
Conversions, when made, consider materials that are available in metric or imperial sizes rather than converting
sizes exactly. For example: Panelboard (plywood) in the US is typically 4 feet X 8 feet (1220 x 2440 mm) while
panelboard in metric countries is typically 1200 X 2400 mm. Since the standard was developed based on readily
available materials these variations in material sizes could not have been practically considered.
The content of the document below has not been modified.
K
NOT MEASUREMENT
SENSITIVE
MIL-STD-105E
10 MAY 1989
SUPERSEDING
MIL-STD-105D
29 APRIL 1963
MILITARY STANDARD
SAMPLING PROCEDURES AND TABLES
FOR INSPECTION BY ATTRIBUTES
AMSC N/A
AREA QCIC
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
MIL-STD-105E
DEPARTMENT OF DEFENSE
Washington, DC 20301
SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES
1. This military standard is approved for use by all Departments and Agencies
of the Department of Defense.
2. Beneficial comments (recommendations, additions, deletions) and any
pertinent data which may be of use in improving this document should be
addressed to:
Commander
U.S. Army Armament Research, Development and
Engineering Center
ATTN: SMCAR^BAC-S/Bldg. 6
Picatinny Arsenal, NJ 07806-5000
by using the self-addressed Standardization Document Improvement Proposal
(DD Form 1426) appearing at the end of this document or letter.
li
MTL-STD-105E
FOREWORD
This publication provides sampling procedures and reference tables for use in
planning and conducting inspection by attributes. The sampling concept is based
on the probabilistic recurrence of events when a series of lots or batches are
produced in a stable environment.
This publication should be used to guide the user in the development of an
inspection strategy that provides a cost effective approach to attaining
confidence in product conpliance with contractual technical requirements. The
user is warned of the assumed risks relative to the chosen sample size and
AQL.
Military specifications should not contain requirements for use of specific
sampling plans, nor should they provide AQL's or LTPD's as a requirement.
Sampling plans for continuous, rather than lot inspection, are contained in
MfL-STD-1235, "Single and Multi-Level Continuous Sampling Procedures and Tables
for Inspection by Attributes".
iii
MIL-STD-105E
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- military time chart
- calculating fte for part time full time temp casual hourly
- printable military time minutes chart
- time sheet minutes to tenths conversion
- logistics forecasting and estimates in the brigade combat team
- military standard
- 24 hour clock conversion sheet military time standard 24
- printable military time conversion chart
- military adjustments to income
- logistics forecasting estimates brigade combat team
Related searches
- simple interest tables for loans
- indoor water tables for children
- interest rate tables for mortgage loans
- federal tax tables for retirees
- drug testing procedures and protocol
- irs life expectancy tables for rmd
- new rmd tables for 2020
- withholding tables for pension payments
- federal tax tables for married couples
- irs gov tax tables for 2019
- tax tables for 2019 tax return
- conversion tables for all units