MILITARY STANDARD
MIL-STD-105E
Page 1 of 74
NOT MEASUREMENT SENSITIVE MIL-STD-105E 10 MAY 1989 SUPERSEDING MIL-STD-105D 29 APRIL 1963
MILITARY STANDARD
SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES
AMSC N/A
AREA QCIC
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited
MIL-STD-105E
Page 2 of 74
MIL-STD-105E
DEPARTMENT OF DEFENSE
Washington, DC 20301
SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES
1. This military standard is approved for use by all Departments and Agencies of the Department of Defense.
2. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to:
Commander
U.S. Army Armament Research, Development and Engineering Center ATTN: SMCAR-BAC-S/Bldg. 6 Picatinny Arsenal, NJ 07806-5000
By using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or letter.
ii
MIL-STD-105E
MIL-STD-105E
Page 3 of 74
FOREWORD
This publication provides sampling procedures and reference tables for use in planning and conducting inspection by attributes. The sampling concept is based on the probabilistic recurrence of events when a series of lots or batches are produced in a stable environment. This publication should be used to guide the user in the development of an inspection strategy that provides a cost-effective approach to attaining confidence in product compliance with contractual technical requirements. The user is warned of the assumed risks relative to the chose sample size and AQL. Military specifications should not contain requirements for use of specific sampling plans, nor should they provide AQL's or LTPD's as a requirement. Sampling plans for continuous, rather than lot inspection, are contained in MIL-STD-1235, "Single and Multi-Level Continuous Sampling Procedures and Tables for Inspection by Attributes".
iii
MIL-STD-105E
Paragraph
1. 1.1 1.2 2. 2.1 3. 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 4. 4.1 4.2 4.3 4.4 4.4.1 4.4.2 4.4.3
CONTENTS
SCOPE Purpose Application REFERENCED DOCUMENTS Not applicable DEFINITIONS Acceptable Quality Level (AQL) Average Outgoing Quality (AOQ) Average Outgoing Quality Limit (AOQL) Classification of Defects Critical Defect Critical Defective Defect Defective Defects per Hundred Units Inspection Inspection by Attributes Lot or Batch Lot or Batch Size Major Defect Major Defective Minor Defect Minor Defective Percent Defective Process Average Sample Sample Size Code Letter Sampling Plan Unit of Product GENERAL REQUIREMENTS Written Procedures Nonconformance Formation and Identification of Lots or Batches AQL AQL Use Limitation Choosing AQL's
iv
Page 4 of 74
Page
1 1 1 1 1 1 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 5 5 5 5 5
MIL-STD-105E
Paragraph
4.5 4.5.1 4.5.2 4.5.3 4.6 4.7 4.7.1 4.7.2 4.7.3 4.7.4 4.8 4.9 4.9.1 4.9.2 4.9.3 4.9.4 4.10 4.10.1 4.10.1.1 4.10.1.2 4.10.1.3 4.10.1.4 4.10.2 4.11 4.12 4.12.1 4.12.2 5. TABLE I. II-A.
II-B
II-C
III-A
III-B
III-C
CONTENTS- Continued
Sampling Representative Sampling Time of Sampling Double of Multiple Sampling Inspection Procedures Switching Procedures Normal to Tightened Tightened to Normal Normal to Reduced Reduced to Normal Discontinuation of Inspection Sampling Plans Inspection Level Code Letters Obtaining Sampling Plan Types of Sampling Plans Determination of Acceptability Percent Defective Inspection Single Sampling Plan Double Sampling Plan Multiple Sampling Plan Special Procedure for Reduced Inspection Defects Per Hundred Units Inspection Limiting Quality Protection Curves Operating Characteristic Curves Average Sample Size Curves TABLES
Sample Size Code Letters Single Sampling Plans for Normal Inspection (Master table) Single Sampling Plans for Tightened Inspection (Master table) Single Sampling Plans for Reduced Inspection (Master table) Double Sampling Plans for Normal Inspection (Master table) Double Sampling Plans for Tightened Inspection (Master table) Double Sampling Plans for Reduced Inspection (Master table)
v
Page 5 of 74
Page
5 5 5 5 6 6 6 6 6 6 7 7 7 7 7 8 8 8 8 8 8 8 9 9 9 9 9 11
13
14
15
16
17
18
19
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- military time chart
- calculating fte for part time full time temp casual hourly
- printable military time minutes chart
- time sheet minutes to tenths conversion
- logistics forecasting and estimates in the brigade combat team
- military standard
- 24 hour clock conversion sheet military time standard 24
- printable military time conversion chart
- military adjustments to income
- logistics forecasting estimates brigade combat team
Related searches
- military lodging facilities in boston
- american military university fafsa code
- military lodging massachusetts for retirees
- words of appreciation for military service
- military thank you note examples
- thank you for your military service
- thank you for your military service letter
- military thank you wording
- federal tax calculator military retirement
- military thank you sayings
- military tuition assistance
- military time management essay