American Hunter 6 & 12 Volt Timer Only Units
American Hunter 6 & 12 Volt Timer Only Units
Set Number
226720
SKU
20019306
6 & 12 VOLT DIGITAL TIMER
OPERATING INSTRUCTIONS STOCK #30556
MODEL # BL-FM6/12D
This all new Feeder Max Digital Timer allows you to feed ? WHEN YOU WANT TO FEED!
Finally modern digital technology that is easy to set at an affordable price.
Features: ? 1 to 16 different feeding settings per day ? Can feed various days of the week ? Adjustable feed rate (1 to 30 seconds) ? 5 seconds test delay (allows time to walk away) ? Fused protected (10 amps) ? Reverse polarity protected ? Quick disconnect wiring harness ? Prewired to add solar charger and remote control (sold separately) ? Clock dust cover
Note: This timer can replace the majority of 6 or twelve volt timers with a 10 amp load or less.
WARNING: THIS TIMER IS DESIGNED TO OPERATE MOTORS
WITH A 10 AMP OR LESS LOAD
Wiring Harness Connections
+ Red (labeled battery) to + positive battery
- Black (labeled battery) to - negative battery
+ White (labeled motor) to + positive motor
- Black (labeled motor) to - negative motor
Note: The FeederMax wiring harness comes prewired with female bullet connectors to receive a FeederMax Solar Charger or a FeederMax Remote Control. These connectors will not be sued unless the Remote Control or Solar Charger is desired.
P.O. Box 1255 Kaufman, TX 75142
PH 972/962-8190 Fax 972/962-8259
FEEDERMAX
DIGITAL TIMER INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPING TO SET THE CLOCK Setting the clock time and/or program time: The hour ? minute ? day advances automatically if no
buttons are pressed after 6 seconds.
SETTING TIME OF DAY 1. Remove protective cover if installed. 2. Press and hold down the "+" or "-" button for 3 seconds. 3. The "HOUR" indicator will begin to flash. Press "+" or "-" to adjust the hour. Release the button when desired hour is reached. 4. 6 seconds later the "MINUTE" indicator will flash. Press "+" or "-" to adjust the minute. Release the button when the desired minute is reached. 5. 6 seconds later the "DAY" indicator will flash. Press "+" or "-" to adjust the day. Release the button when the desired day is reached. wait 6 seconds. Time is set.
SETTING FEED TIME (1ST SETTING) 1. Remove the protective cover if installed. 2. Press the "PROG" button. The first program indicator digit will begin to flash in the bottom left corner of the LCD display. 3. Press the "PROG" button again to navigate through the 1st program setting. The hour indicator will begin to flash. Press "+" or "-" to adjust the hour. 4. Press "PROG" to set the hour and advance to the "MINUTE" indicator. Press "+" or "-" to adjust the minute. 5. Press "PROG" to set the minute and advance to the "DAY" indicator. Press "+" or "-" to advance through the day selections. Stop when your reach your desired combination. The timer will return to the current time and day display. Note: if you want the unit to operate at the same time every day of the week, it is only necessary to set 1 program cycle for that time of day. However, every day of the week must be shown at the top of the LCD display for that cycle.
SETTING FEED TIMES 2-16 (FOR MULTIPLE FEEDINGS) 6. Press the "PROG" button. The first program indicator digit will begin to flash in the bottom left
corner of the LCD display. 7. Press "+" to navigate to the next program cycle or "-" to navigate to the last program cycle. 8. Repeat steps 2 through 4 above to set programs 2-16. When all desired programs have been
set, just wait 6 seconds and timer will return to current time and day display.
CANCEL PROGRAM FEED TIME 1. Press "PROG" button. Press "+" or "-" to navigate to desired program cycle you want to cancel. 2. Press and hold "PROG" button until time display clears hour and minutes (3seconds). Release button. Wait! The timer will return to current time and day display after approximately 20 seconds.
RATE OF FEED 1. Press "TEST" button, the feed rate duration indicator is displayed. 2. Press "+" or "-" to adjust the duration time (1 ? 30 seconds). The timer will return to current time and day display after approximately 30 seconds.
TIMMER RESET Press yellow recessed "R" button. The current clock setting will reset to 12:00 AM Monday, and all program cycle settings will be reset as well.
TEST 1. Press "TEST" button, the feed rate duration indicator is displayed. 2. Pres "TEST" button again to activate test. USE CAUTION! There is a 5 second delay. The timer will return to current time and ay after approximately 30 seconds.
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- american hunter 6 12 volt timer only units
- bmw connected drive
- speeds and feeds for carbide endmills internal tool
- an introduction to rss feeds
- moto z play droid user guide
- how to join facebook aarp
- facebook s privacy trainwreck danah boyd
- activity scheduler otify e and subscribe
- sample rss feeds it umn
- microbiological control strategy in cooling tower systems
Related searches
- 120v to 12 volt converter
- 12 volt to 120 adapter
- 110 volt 12 volt converter
- 110 volt to 12 volt converter
- 12 volt heavy equipment batteries
- heavy duty 12 volt battery
- 12 volt commercial battery
- 12 volt wire gauge calculator
- 12 volt wiring chart
- 12 volt wire size calculator
- 12 volt wire gauge guide
- msr 10 hunter 6 5 creedmoor