PowerPCB Training Manual, Your First Design
ENGINEERING CHECKLIST
PLACEMENT PLOTS 2:1 & 1:1 SCALE
BOARD OUTLINE
____ 1) MEASURE FOR ACCURACY
____ 2) ALL COMPONENTS INSIDE BY .1"
____ 3) INSIDE CUTOUTS
____ 4)
CONNECTORS
____ 1) PIN 1 & 2 IN CORRECT LOCATION
____ 2) PINS SPACED CORRECTLY
____ 3) END PINS NUMBERED ON SILK-SCREEN
____ 4) SILK-SCREEN OUTLINE CORRECT
____ 5) PIN ROWS NOT SWAPPED
____ 6) BUILT FROM COMPONENT SIDE NOT SOLDER SIDE
____ 7)
NEW LIBRARY PARTS (SEE NEW LIBRARY REPORT ON FLOPPY)
____ 1) SCALE WITH ACTUAL PART ON 1:1 SCALE DWG
____ 2) CHECK PAD & HOLE SIZE
____ 3) CHECK SILK-SCREEN OUTLINE SCALE
____ 4) CHECK PIN 1 & PIN 2 LOCATION
____ 5)
COMPONENT LAYOUT
____ 1) SPARES
____ 2) SOCKETS
____ 3) OVERLAPPING PARTS
____ 4) COMPONENT ORIENTATION
____ 5) LOCATION OF ADJUSTABLE PARTS
____ 6)
TEXT
____ 1) COMPANY NAME, BOARD NAME & NUMBER
____ 2) S/N BLOCK REV BLOCK
____ 3) ALL REFERENCE DESIGNATORS OUTSIDE PARTS
____ 4) TEXT ORIENTATION
____ 5)
SMT
____ 1) FIDUCIAL LOCATIONS
____ 2) LAND PATTERNS ON NEW PARTS
____ 3) TEXT IS OFF ALL LAND PATTERNS
____ 4)
ENGINEERING CHECKLIST
DRILL DRAWING 2:1 OR 1.5:1 SCALE
NOTES
____ 1) SOLDER MASK
____ 2) SILK-SCREEN
____ 3) BOARD THICKNESS
____ 4) PLATING THICKNESS
____ 5) GOLD PLATING
____ 6) ELECTRICAL TEST
____ 7)
CHART
____ 1) DRILL SYMBOLS
____ 2) DRILL SIZES
____ 3) DRILL TOLERANCES
____ 4) HOLE QUANTITIES
____ 5) PLATED/NO PLATING
____ 6)
LAY-UP DETAIL
____ 1) CORRECT LAYER STACK UP
____ 2) BOARD THICKNESS
____ 3) CRITICAL LAMINATE THICKNESS
____ 4)
DIMENSIONED DRAWING
____ 1) CHECK NEW LIBRARY PART DRILL SIZE
____ 2) CORRECT DIMENSION TEXT VALUES
____ 3) IS A MOUNTING / TOOLING HOLE DIMENSIONED FROM BOARD EDGE
____ 4) DO DRILL SYMBOLS MATCH CHART
____ 5) ARE ALL BOARD EDGES DIMENSIONED
____ 6)
TITLE BLOCK
____ 1) CORRECT COMPANY NAME
____ 2) CORRECT BOARD NAME
____ 3) CORRECT BOARD NUMBER
____ 4) CORRECT SCALE
____ 5) CORRECT REVISION
____ 6)
ENGINEERING CHECKLIST
REPORTS
NON-CONNECTED PINS NON.TXT
____ 1) CHECK AGAINST SCHEMATIC
____ 2) VERIFY ALL LISTED PINS NOT CONNECTED ARE CORRECT
____ 3)
SHAPE TYPE LIST SHP.TXT
____ 1) CHECK AGAINST PARTS LIST
____ 2)
NETLIST NET.TXT
____ 1) COMPARE AGAINST ORIGINAL NETLIST USING "NETCHECK TOOLS"
____ 2) COMPARE AGAINST SCHEMATIC
____ 3) CHECK PINS ON CAPS, DIODES, TRANSISTORS, BATTERIES & POTS
____ 4)
COMPONENT COORDINATES COR.TXT
____ 1) CHECK PIN 1 LOCATIONS OF CONNECTORS & FIXED PARTS
____ 2) MATCH LOCATION OF MTG. HOLES TO CONSTRAINT DWG
____ 3)
NEW LIBRARY PARTS NEW.TXT
____ 1) USE THIS LIST TO CHECK ASSEMBLY DRAWING
____ 2)
LENGTH REPORT LEN.TXT
____ 1) CHECK CRITICAL LINE LENGTHS
____ 2)
WAS/IS LIST LST.TXT
____ 1) BACK ANNOTATE SCHEMATIC
____ 2)
ENGINEERING CHECKLIST
ROUTED CHECK PLOTS
TRACE LAYERS
____ 1) BELOW BOARD TEXT
____ 2) CROP MARKS
____ 3) SOLDER SIDE ETCH TEXT MIRRORED
____ 4) PLANES UNDER COMPONENT (I.E. CRYSTALS & HEAT SINK AREAS)
____ 5) ARE SHORTING JUMPERS CORRECT
____ 6) CRITICAL TRACK ROUTING
____ 7) CHECK TRACK WIDTH
____ 8) LAYERING WINDOW
____ 9) NO TRACKS IN KEEP OUT AREAS
____ 10) DISTANCE BETWEEN VIAS
____ 11) DO ALL NETS HAVE A TEST VIA (IF REQUIRED)
____ 12) ARE TERMINATING RESISTORS ROUTED CORRECTLY
____ 13)
PLANES
____ 1) PLANES SPLIT CORRECTLY
____ 2) SPLIT OVER THERMAL
____ 3) CLEARANCES - MOUNTING HOLES & BOARD EDGE
____ 4) BELOW BOARD TEXT
____ 5) OPAQUE OUT AREAS
____ 6)
SILK-SCREEN
____ 1) IF BOARD WAS RENAMED, ARE PART NAMES IN ORDER
____ 2) TEXT OVER VIAS
____ 3) SOLDER SIDE SILK-SCREEN MIRRORED TEXT
____ 4) COMPANY NAME, BOARD NAME, AND BOARD NUMBER
____ 5)
ENGINEERING CHECKLIST
FINAL APPROVAL
FILM
____ 1) CHECK AIR GAP VIOLATIONS
____ 2) BELOW BOARD TEXT, CORRECT SPELLING & REVISION
____ 3) BOARD OUTLINE .004”
____ 4) VOLTAGE PLANE SPLITS
____ 5) PLANE THERMOS CORRECT
____ 6) MEASURE TARGETS FOR ACCURACY
____ 7) ARE VIAS TINTED ON SOLDER MASK
____ 8)
DRILL DRAWING
____ 1) NOTES
____ 2) CHART
____ 3) LAY-UP DETAIL
____ 4) DIMENSIONED DRAWING
____ 5) TITLE BLOCK
____ 6)
ASSEMBLY DRAWING
____ 1) BOARD OUTLINE
____ 2) TEXT
____ 3) CORRECT VIEW (BOTTOM SIDE ASSEMBLY)
____ 4) TITLE BLOCK
____ 5)
BACKUP DISKETTE
____ 1) PADS JOB FILE
____ 2)
GERBER DISKETTE
____ 1) REVIEW README.FAB FILE
____ 2) ARE ALL GERBER FILES ON DISKETTE
____ 3) ARE APERTURE TABLES (.REP FILES) ON DISKETTE
____ 4) ARE DRILL FILES ON DISKETTE .DRL, .LST, .REP
____ 5) IS DRILL DRAWING PEN PLOT FILE ON DISKETTE .PLT
____ 6)
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- section 31 63 26 drilled caissons
- heading 1 tw cen mt condensed 18 pt
- pads powerpcb to autocad boston university
- burner btu calculator instructions
- usmc ribbon united states marine corps
- powerpcb training manual your first design
- tap drill size chart for standard threads
- csi format chain link fence specification
- stress areas of screw threads of a fastener
- basic nec code rules and design practice
Related searches
- microsoft excel training manual pdf
- free excel training manual download
- starbucks barista training manual pdf
- excel 2013 training manual pdf
- free outlook training manual pdf
- excel training manual pdf
- customer service training manual pdf
- barista training manual pdf
- training manual for supervisors
- supervisor training manual for manufacturing
- church leadership training manual pdf
- basic computer training manual pdf