Mandatory Experiment 7



Mandatory Experiment 7.6

The extraction of clove oil from cloves (or some similar alternative) by steam distillation

Teacher Material

• Cloves are the dried buds of a tree that is cultivated primarily in Zanzibar and Madagascar. The tree produces abundant clusters of small red flower buds that are gathered before opening and are dried to produce the dark-brown, nail-shaped spice clove.

• Whole and ground cloves are popular food seasonings and account for the use of half the world production of cloves. The other half is ground and used in the manufacture of a type of cigarette popular in Indonesia.

• Almost 20 percent of the clove's weight is essential oil, obtained by distillation and used in perfumes, blends of spices, medicines, and sweets. Clove oil is a powerful antiseptic, and is also used as a local anaesthetic for toothache.

• A 100 cm3 flask should be used for holding the cloves as it eliminates the need for a water trap between the steam generator and the flask with the cloves. Using a larger flask allows for it to be filled up to some extent with water - without having to dismantle the apparatus and empty out excess water.

• After steam starts to come over from the steam generator, the Bunsen burner can be moved over occasionally to heat the flask containing the cloves. If this is not done, the flask should be insulated (e.g. with aluminium foil) to prevent an undue amount of water condensing in the flask.

• The setting up of the apparatus for this experiment will take the students quite some time as it is quite difficult to align all the connections properly, The Quickfit steam generator flask (150 cm3) should contain about 100 cm3 of water to start with. If during the experiment, the level of water drops too low, the steam distillation will not work smoothly. If this happens, add some hot water to the steam distillation flask from a kettle of boiling water.

• The bottom of the safety tube should be well below the water surface in the steam generator, but not touching the bottom of the flask.

• The use of Bibby clips to hold the parts of the assembled Quickfit apparatus together is recommended.

• It is advisable to have a supply of boiling water available at the start of the experiment. This may make it possible for students to complete the experiment within a double period.

• In the diagram of the steam distillation apparatus, the separating funnel shown is only necessary if the optional extension work is to be done. Otherwise a beaker or conical flask is more convenient for collecting the distillate.

• It is inadvisable to use powdered cloves. If they are used, the steam inlet may become blocked.

• Alternatives to the quickfit steam generator include a 1 litre copper steam generator with a built in water gauge, and a large Pyrex conical flask. A glass steam generator is preferable, as it allows students to see what is happening in the generator.

• Students are expected to know how a pure clove oil could be isolated by solvent extraction (see extension work).

• A small scale or semi-micro method is available for those schools in possession of BASF mini-labs or similar equipment. Increased safety and reduced waste and shorter time required for the practical are three of the advantages of this alternative method.

Extension Work

Separation of clove oil from water

The procedure is as follows:

1. Disconnect the dropping funnel from the rest of the apparatus.

2. Add about 8 cm3 of cyclohexane to the distillate in the dropping funnel.

3. Stopper the dropping funnel and shake the mixture. Release any pressure build-up

carefully after each shake by inverting the dropping funnel while holding the stopper

and slowly opening and shutting the tap.

4. Run the lower aqueous layer off. Collect the top layer - this contains the clove oil and the cyclohexane.

[pic]

5. Dry the organic layer by shaking with anhydrous sodium sulfate in a conical flask. If possible, allow to stand overnight, before removing the solid by filtration or decanting.

6. Separate the more volatile cyclohexane from the clove oil by placing the mixture in a small beaker (whose mass is known) on a water-bath in a fume cupboard. The cyclohexane evaporates, leaving the clove oil behind. (Note that if the cyclohexane is to be distilled off it will boil at 81 0C.) Prepare the students for a very low yield of clove oil.

7. Note the smell of the clove oil. Do not allow the clove oil to come in contact with your skin.

• Alternatives to cloves as a starting material for this experiment include the skin of an orange, lemon or grapefruit. Something slightly more adventurous would be (a) the resin extruded by conifer trees or (b) the dried fermented seed pods of the vanilla orchid.

Preparation of reagents

None required for this experiment.

Quantities needed per working group

Whole cloves 5 to 10g

Cyclohexane 10 cm3

Safety considerations

• Safety glasses must be worn.

• The use of heat-resistant gloves is recommended

.

• Hair should be tied back if necessary.

• Steam can cause serious burns. Make sure that each experimental set-up is firmly clamped with the two safety openings in place. The first safety valve is in the Quickfit steam generator. The second safety valve is part of the delivery tube attached to the end of the Liebig condenser.

• Suck-back might happen if the heat is removed from the steam-generator.

Make sure the students disconnect the apparatus before turning off the heat.

Chemical hazard notes

One of the major components of clove oil is eugenol, an aromatic compound that can burn skin. Gloves should be worn when handling the product of the experiment.

Cyclohexane [pic] is volatile and flammable.

Sodium sulfate is an irritant to eyes.

Disposal of wastes

Any residual cyclohexane may be allowed to evaporate in a fume cupboard. Solid residues can be washed with water and bagged for landfill waste.

Suggested answers to student questions

(1) Explain why the clove oil could not be distilled directly from the cloves.

Clove oil contains component molecules whose boiling points are quite high. Heating

them to their boiling point would be destructive.

(2) Explain the principles by which steam distillation works.

Some organic compounds are immiscible with water. Usually these compounds have

a low vapour pressure. After mixing them with water, however, the mixture will distil

when the sum of the two vapour pressures reaches atmospheric pressure. It follows,

then, that this must happen below the boiling point of water. This process is known as

steam distillation.

(3) Suggest a reason why the clove oil is much more soluble in non-polar solvents

(than in water).

The component molecules found in clove oil are often relatively non-polar and will

therefore be more soluble in the non-polar solvent than in water.

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download