COSROCS - It IS rocket science!
[pic]
National Aeronautics and
Space Administration
Student Launch Initiative
Preliminary Design Review
1 Summary of PDR report
1.1 Team summary
1 Cheyenne Mountain Charter Academy
2 The Vanguard School
1605 S. Corona Avenue
Colorado Springs, Colorado 80905
3 Mentors: Jeff Lane, Ernie Puckett, Steve Madere, Warren Layfield, George Schaffer, Jason Unwin, Ann Conner
1.2 Launch Vehicle Summary
1. Size: 95 inches long x 3.9 inches in diameter
2. Motor choice: Animal Motor Works (AMW) K350RR High Power Rocket Motor
3. Recovery system: Main Parachute bay 18 inches long [100in round main parachute]. Drogue Parachute Bay 14 inches long [30in round drogue parachute]
1.3 Payload Summary
1. We will place a digital camera and GPS in the rocket and a known-length object on the ground, and then we will be able to determine the exact level of accuracy of the altimeter through comparison of GPS data, pixel analysis, and altimeter data.
1.b Data analysis issues:
While the altimeter is more precise than the camera, the velocity of the rocket flops this relationship because of the sample rate (ten per second) of the altimeter.
If the rocket accelerates to 150fps at the end of the 8 foot launch rail in .15 sec (general numbers from Rocksim), we'll have one data point from the altimeter and 9 frames from the camera (at 60 fps) by the time the rocket leaves the rail.
The lower the camera is (the closer to the measuring device), the more precise it is. Though we won't need to do this, with the camera closer to the ground, and with its resolution capabilities, we could determine altitude down to a fraction of an inch if we had a regular ruler on the ground for the camera to shoot. The altimeters are not capable of this level of precision.
Therefore, at a specific distance from the measuring device (very generally this distance is probably one pixel per foot in each frame), the camera's digital pixels become LESS precise than the altimeter's output, given a static altitude. This distance would be 1280 feet in altitude (1280 pixels of resolution) with a normal lens.
The rocket's velocity will peak just before motor burnout at around 2.5 seconds. Coincidentally, this will occur at about the same altitude that our camera becomes less precise than our altimeter, but with a velocity of around 800 fps, we'll be getting data points every 80 feet from the altimeter, whereas we'll still be getting digital frames every 13 feet from the camera (at 60fps). When we add velocity into the big picture, the tipping point (with a normal lens at 60fps) will be where the velocity slows to significantly less than 100fps and the altitude is well above 5000 ft.
The camera is being used in the experiment as the reference device; precision is based on repeatable and reliable static tests on the ground to obtain a “true” and valid altitude. Our hypothesis is that the altimeters are not accurate, because our experience with them is that they're not, and each altimeter's accuracy varies at different altitudes when comparing multiple altimeters.
The repeatable nature of data points from the altimeters is not a consideration in our experiment. Additional experimentation might be done in the future to establish how far they deviate from one flight to another.
Data will be collected and compared after the flight, not live. Because of the lag for air escaping from the payload bay, and because the barometric altimeters don’t begin recording until 40-250 to reduce false triggering from wind gusts, we will have significant work post-flight synchronizing the video data with the altimeter data.
2 Changes Made Since Proposal
1. We have made no changes to our vehicle criteria, payload criteria, or activity plan so far.
3 Vehicle Criteria
3.1 Selection, Design, and Verification Launch Vehicle
1. Our mission is to build, test, fly, and recover a reusable rocket with a scientific payload with altimeters and cameras and to gather data to test the accuracy of the altimeters. As a secondary mission, we hope to inspire teenagers to consider careers as scientists and engineers.
2. If our mission is successful we shall be able to create a smooth, precise curve on a chart and compare with the data from the various altimeters to determine the altimeters’ accuracy.
3.5. We are concerned about breaking a material while testing it, therefore we will take necessary precautions to be careful with our tests.
We are concerned about parts not arriving on time, so we will order each part before needed in case of setbacks.
We are concerned about not having enough people to test the materials and test fly the rocket, so we have made sure that each person on the team is eligible to fly rockets and test them.
We have encouraged commitment to this program by requiring a monthly fee of 100 dollars from each family with scholarships available for those who qualify for federal school lunch programs.
School holidays have proven to be a problem because many of our members go on vacations and therefore do not attend meetings and tests. To stop this from happening we either cancel the meeting so they don’t miss any vital information or tests or have another meeting.
3.6. We will test the body tube with deformation tests. We will do deformation tests on the nose cone. We will also do flex test on the fins. We will also test all joints and anchor points to be sure of strength. In addition, we will get as much materials stress test information on each component from the manufacturers as possible.
4. Recovery Subsystem.
4.1 Using design tools we have determined that we need a main parachute diameter of 105.06, drogue parachute diameter of 31.52 inch, and 2 grams of black powder for the main ejection charge and 1.34 grams for the drogue.
5. Mission performance
5.1 For our mission to be a success we must be able to fly and recover the rocket, gather the data, and compare it to determine how accurate altimeters are.
6.Payload integration
6.1 We have three separate payload bays in our rocket. The first one consists of the GPS unit and is located at the very front of the rocket right below the nosecone. The next bay is the camera bay and it is located below the GPS bay. On the outside of the rocket is a hole where light enters the camera lens. Against the hole is a small mirror placed at a 45 degree angle so the camera can look down the side of the rocket towards the ground. On top of the mirror is a hood that protects the mirror and creates a better aerodynamic design with lower drag coefficient and less asymmetry to change the path of the rocket. The last payload bay is the altimeter bay. This houses the altimeters which eject the parachutes and collect the data.
7. Launch operation procedures
7.1 We will be using a custom made launch system fabricated by Ernie Puckett and a custom made launch pad made by Norman Pfund with a ¼ inch 8 foot long launch rail.
8. Safety and Environment
8.1 Our team’s safety officer is Trenton Tulloss.
8.2 Safe Distances
-No person shall be closer to the launch of a high power rocket than the person actually launching the rocket and those authorized by the Safety Monitor (Trenton).
-All spectators shall remain within an area determined by the Safety Monitor and behind both the Safety Monitor and the person launching the rocket.
-A person shall not be closer to the launch of a high power rocket than the applicable minimum safe distance.
• Launch Operations
-Do not ignite and launch a high power rocket horizontally, at a target, in such a way that the rocket's flight path goes into clouds or beyond the boundaries of the flying field (launch site).
-Do not launch a high power rocket if the surface wind at the launch site is more than twenty (20) miles per hour.
-Do not operate a high power rocket in a manner that is hazardous to aircraft.
• Launch Control.
-Launch a high power rocket only with the immediate knowledge, permission, and attention of the Safety Monitor.
-All persons involved in the launch, all spectators, and parking areas during a countdown and launch shall be facing the launcher if requested to do so by the Safety Monitor.
-Precede the launch with a five (5) second countdown audible throughout the launching, spectator, and parking areas. This countdown shall be given by the person launching the rocket, the Safety Monitor, or other launch site operating personnel.
-Do not approach a high power rocket that has misfired until the safety inter-lock has been removed or the battery has been disconnected from the ignition system, one minute has passed, and the Safety Monitor has given permission for only a single person to approach the misfired rocket to inspect it.
Safety Tables
TABLE 1: LAUNCH SITE DIMENSIONS
|Installed Total Impulse |Equivalent Motor |Minimum Site Distance |Equivalent Distance |
|(N-sec) |Type |(feet) |(miles) |
|160.01 - 320.00 |H |1,500 |.28 |
|320.01 - 640.00 |I |2,500 |.50 |
|640.01 - 1280.00 |J |5,280 |1.00 |
|1280.01 - 2560.00 |K |5,280 |1.00 |
|2560.01 - 5120.00 |L |10,560 |2.00 |
|5120.01 - 10240.00 |M |15,480 |3.00 |
|10240.01 - 20480.00 |N |21,120 |4.00 |
|20480.01 - 40960.00 |O |26,400 |5.00 |
TABLE 2: SAFE DISTANCE
|Installed Total Impulse |Equivalent Motor |Minimum Safe Distance |Complex |
|(N-sec) |Type |(feet) |Minimum Safe Distance |
| | | |(feet) |
|160.01 - 320.00 |H |50 |100 |
|320.01 - 640.00 |I |100 |200 |
|640.01 - 1280.00 |J |100 |200 |
|1280.01 - 2560.00 |K |200 |300 |
|2560.01 - 5120.00 |L |300 |500 |
|5120.01 - 10240.00 |M |500 |1,000 |
|10240.01 - 20480.00 |N |1,000 |1,500 |
|20480.01 - 40960.00 |O |1,500 |2,000 |
MATERIAL SAFETY DATA SHEET
[pic]
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
[pic]
|Elmer's Products, Inc. |Emergency Phone Number: |
|1 Easton Oval |Poison Control Center |
|Columbus, OH 43219 |1-888-516-2502 |
For additional product information, access our website at or call 1-888-435-6377. To place an order, call 1-800-848-9400.
SUBSTANCE: ELMER'S ULTIMATE GLUE
TRADE NAMES/SYNONYMS:
P9405; P9406; P9411; P9412; P9413; P9415; P9416; P9417
CREATION DATE: Jun 08 2007
REVISION DATE: Jun 22 2007
[pic]
2. COMPOSITION, INFORMATION ON INGREDIENTS
[pic]
COMPONENT: POLYMETHYLENE POLYPHENYL ISOCYANATE
CAS NUMBER: 9016-87-9
PERCENTAGE: 30-50
COMPONENT: METHYLENE BISPHENYL ISOCYANATE
CAS NUMBER: 101-68-8
PERCENTAGE: 30-50
COMPONENT: NON-HAZARDOUS SUBSTANCE
CAS NUMBER: Not assigned.
PERCENTAGE: 10-30
COMPONENT: CHLOROBENZENE
CAS NUMBER: 108-90-7
PERCENTAGE: 230 F (>110 C) (CC)
AUTOIGNITION: >1112 F (>600 C)
FLAMMABILITY CLASS (OSHA): IIIB
HAZARDOUS COMBUSTION PRODUCTS:
Thermal decomposition or combustion products: cyanides, oxides of carbon, oxides of nitrogen
[pic]
6. ACCIDENTAL RELEASE MEASURES
[pic]
OCCUPATIONAL RELEASE:
Stop leak if possible without personal risk. Small spills: Absorb with sand or other non-combustible material. Collect spilled material in appropriate container for disposal. Notify Local Emergency Planning Committee and State Emergency Response Commission for release greater than or equal to RQ (U.S. SARA Section 304). If release occurs in the U.S. and is reportable under CERCLA Section 103, notify the National Response Center at (800)424-8802 (USA) or (202)426-2675 (USA).
[pic]
7. HANDLING AND STORAGE
[pic]
STORAGE: Store and handle in accordance with all current regulations and standards. Keep container tightly closed. Store in a well-ventilated area. Avoid contact with water or moisture. Store between 16 C and 38 C. A hazardous build-up of pressure could result due to a reaction with water producing carbon dioxide gas if contaminated containers are resealed. Do not reseal contaminated containers. Reseal uncontaminated containers that are free of moisture only after placing under a nitrogen blanket. Do not store in containers made of copper, copper alloys, or galvanized surfaces. See original container for storage recommendations. Keep separated from incompatible substances.
HANDLING: Use only with adequate ventilation. Avoid breathing vapor or mist. Avoid prolonged or repeated contact with skin or eyes. Wash thoroughly after handling. Do not get in eyes.
[pic]
8. EXPOSURE CONTROLS, PERSONAL PROTECTION
[pic]
EXPOSURE LIMITS:
POLYMETHYLENE POLYPHENYL ISOCYANATE:
METHYLENE BISPHENYL ISOCYANATE:
0.02 ppm (0.2 mg/m3) OSHA ceiling
0.005 ppm ACGIH TWA
0.005 ppm (0.05 mg/m3) NIOSH recommended TWA 10 hour(s)
0.020 ppm (0.2 mg/m3) NIOSH recommended ceiling 10 minute(s)
METHYLENE BISPHENYL ISOCYANATE:
0.02 ppm (0.2 mg/m3) OSHA ceiling
0.005 ppm ACGIH TWA
0.005 ppm (0.05 mg/m3) NIOSH recommended TWA 10 hour(s)
0.020 ppm (0.2 mg/m3) NIOSH recommended ceiling 10 minute(s)
VENTILATION: Provide local exhaust or process enclosure ventilation system. Ensure compliance with applicable exposure limits.
EYE PROTECTION: Wear splash resistant safety goggles with a face shield. Provide an emergency eye wash fountain and quick drench shower in the immediate work area.
CLOTHING: Wear appropriate chemical resistant clothing.
GLOVES: Wear appropriate chemical resistant gloves.
PROTECTIVE MATERIAL TYPES: neoprene, nitrile, butyl rubber
RESPIRATOR: Under conditions of frequent use or heavy exposure, respiratory protection may be needed. Respiratory protection is ranked in order from minimum to maximum. Consider warning properties before use.
Any dust, mist, and fume respirator.
Any air-purifying respirator with a high-efficiency particulate filter.
Any powered, air-purifying respirator with a dust, mist, and fume filter.
Any powered, air-purifying respirator with a high-efficiency particulate filter.
For Unknown Concentrations or Immediately Dangerous to Life or Health -
Any supplied-air respirator with full face piece and operated in a pressure-demand or other positive-pressure mode in combination with a separate escape supply.
Any self-contained breathing apparatus with a full face piece.
[pic]
9. PHYSICAL AND CHEMICAL PROPERTIES
[pic]
PHYSICAL STATE: liquid
COLOR: brown
ODOR: musty odor
BOILING POINT: >572 F (>300 C) (decomposes)
FREEZING POINT: Not available
VAPOR PRESSURE: 0.000004 mmHg
VAPOR DENSITY (air=1): 8.5
SPECIFIC GRAVITY (water=1): 1.129
WATER SOLUBILITY: reacts, immiscible
PH: Not available
VOLATILITY: Not available
ODOR THRESHOLD: Not available
EVAPORATION RATE: Not available
VISCOSITY: 2311 cP
COEFFICIENT OF WATER/OIL DISTRIBUTION: Not available
[pic]
10. STABILITY AND REACTIVITY
[pic]
REACTIVITY: May react on contact with water. Closed containers may rupture.
CONDITIONS TO AVOID: Avoid heat, flames, sparks and other sources of ignition. Avoid contact with incompatible materials.
INCOMPATIBILITIES: acids, alcohols, amines, bases, combustible materials, metal salts, metals, oxidizing materials
HAZARDOUS DECOMPOSITION:
Decomposition products on contact with water or moisture: oxides of carbon
Thermal decomposition or combustion products: cyanides, oxides of carbon, oxides of nitrogen
POLYMERIZATION: Polymerization may occur in the presence of metal compounds, alkalies, and tertiary amines at elevated temperatures.
[pic]
11. TOXICOLOGICAL INFORMATION
[pic]
ELMER'S ULTIMATE GLUE:
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: skin disorders, respiratory system (including asthma and other breathing disorders)
POLYMETHYLENE POLYPHENYL ISOCYANATE:
IRRITATION DATA: 100 mg eyes-rabbit mild
TOXICITY DATA: 490 mg/m3/4 hour(s) inhalation-rat LC50; >5 ml/kg skin-rabbit LD50; >10000 mg/kg oral-rat LD50
CARCINOGEN STATUS: IARC: Human No Adequate Data, Animal No Adequate Data, Group 3
LOCAL EFFECTS:
Irritant: inhalation, skin, eye
ACUTE TOXICITY LEVEL:
Highly Toxic: inhalation
Relatively Non-toxic: ingestion
TARGET ORGANS: immune system (sensitizer)
TUMORIGENIC DATA: Available.
REPRODUCTIVE EFFECTS DATA: Available.
ADDITIONAL DATA: May cross react with similar compounds.
METHYLENE BISPHENYL ISOCYANATE:
IRRITATION DATA: 500 mg/24 hour(s) skin-rabbit; 100 mg eyes-rabbit moderate
TOXICITY DATA: 178 mg/m3 inhalation-rat LC50; 9200 mg/kg oral-rat LD50
CARCINOGEN STATUS: IARC: Human Inadequate Evidence (Monomer), Group 3
LOCAL EFFECTS:
Irritant: inhalation, skin, eye
ACUTE TOXICITY LEVEL:
Highly Toxic: inhalation
Slightly Toxic: ingestion
TARGET ORGANS: immune system (sensitizer)
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: respiratory disorders
MUTAGENIC DATA: Available.
REPRODUCTIVE EFFECTS DATA: Available.
[pic]
12. ECOLOGICAL INFORMATION
[pic]
Not available
[pic]
13. DISPOSAL CONSIDERATIONS
[pic]
Dispose in accordance with all applicable regulations.
[pic]
14. TRANSPORT INFORMATION
[pic]
U.S. DEPARTMENT OF TRANSPORTATION: No classification assigned.
CANADIAN TRANSPORTATION OF DANGEROUS GOODS: No classification assigned.
[pic]
15. REGULATORY INFORMATION
[pic]
U.S. REGULATIONS:
CERCLA SECTIONS 102a/103 HAZARDOUS SUBSTANCES (40 CFR 302.4):
METHYLENE BISPHENYL ISOCYANATE: 5000 LBS RQ
CHLOROBENZENE: 100 LBS RQ
SARA TITLE III SECTION 302 EXTREMELY HAZARDOUS SUBSTANCES (40 CFR 355.30): Not regulated.
SARA TITLE III SECTION 304 EXTREMELY HAZARDOUS SUBSTANCES (40 CFR 355.40): Not regulated.
SARA TITLE III SARA SECTIONS 311/312 HAZARDOUS CATEGORIES (40 CFR 370.21):
ACUTE: Yes
CHRONIC: Yes
FIRE: No
REACTIVE: No
SUDDEN RELEASE: No
SARA TITLE III SECTION 313 (40 CFR 372.65):
POLYMETHYLENE POLYPHENYL ISOCYANATE
METHYLENE BISPHENYL ISOCYANATE
OSHA PROCESS SAFETY (29CFR1910.119): Not regulated.
STATE REGULATIONS:
California Proposition 65: Not regulated.
CANADIAN REGULATIONS:
WHMIS CLASSIFICATION: Not determined.
NATIONAL INVENTORY STATUS:
U.S. INVENTORY (TSCA): All the components of this substance are listed on or are exempt from the inventory.
TSCA 12(b) EXPORT NOTIFICATION:
CHLOROBENZENE
CAS NUMBER: 108-90-7
SECTION 4
CANADA INVENTORY (DSL/NDSL): Not determined.
[pic]
16. OTHER INFORMATION
[pic]
©Copyright 1984-2007 MDL Information Systems, Inc. All rights reserved.
SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, CONCERNING THE PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE, except that the product shall conform to contracted specifications, and that the product does not infringe any valid United States or Canadian patent. No claim of any kind shall be greater in amount than the purchase price of the quantity of product in respect of which damages are claimed. In no event shall Seller be liable for incidental or consequential damages, whether Buyer's claim is based on contract, breach of warranty, negligence or otherwise.
MATERIAL SAFETY DATA SHEET
02/20/08
Revision #7
Section 1 HAZARD RATING For Chemical Emergency Only:
PACER TECHNOLOGY In the US & Canada (800) 424-9300
9420 Santa Anita Avenue 2 Int'l & Wash DC (COLLECT) (703) 527-3887
Rancho Cucamonga, CA 91730 1 x 1 Telephone for Information :(909) 987-0550
PRODUCT IDENTIFICATION: Super Glue Gel
Section 2 - HAZARDOUS INGREDIENTS INFORMATION:
Hazardous Components OSHA ACGIH OTHER %
(Common Names, CAS Number) PEL TLV LIMITS OPTION
Ethyl-2-Cyanoacrylate (7085-85-0) NE NE 0.2ppm TWA 60-100
Poly (Methyl Methacrylate) (9011-14-7) NE NE 10-30
Hydroquinone* (123-31-9) 2mg/m3 2mg/m3 0-1
*This ingredient is subject to the reporting requirements of Section 313 of Title III of the Superfund
Amendments & Reauthorization Act of 1986 (SARA) and 40 CFR 372.
Section 3 - PHYSICAL/CHEMICAL CHARACTERISTICS:
Boiling Point: 365 F Specific Gravity (H2O=1): 1.05
Vapor Density (Air=1): nil-NE Melting Point: NE
Vapor Pressure (mm Hg): 1 @ 20 C Evaporation Rate (Butyl acetate=1): nil-NE
Solubility in Water: Insoluble, material reacts to hardened mass for non-hazardous waste.
VOC: This product is VOC compliant for sale in California.
Appearance & Odor: Transparent water-white to straw colored liquid with stimulative odor.
Section 4 - FIRE AND EXPLOSION HAZARD DATA:
Flash Point (Method Used): 185 F (TCC) Flammable Limits: LEL: NE UEL: NE
Extinguishing Media: Flush with large amounts of water or dry chemical extinguisher.
Special Fire Fighting Procedures: Fumes may be irritating if not burning and require air supply with goggles while applying large amounts of water or dry chemical extinguisher.
Unusual Fire and Explosion Hazards: None. Combustible requiring the above procedures.
Section 5 - REACTIVITY DATA:
Stability: Stable XX Conditions to Avoid: Excessive heat above 176 F, moisture and alkaline. Stable up to 122 F. Store in a cool dry place.
Incompatibility (Materials to Avoid): Polymerized by water, alcohol, amines, alkaline materials and direct UV.
Hazardous Decomposition Products: Combustible by-products of carbon monoxide/dioxide.
Hazardous Polymerization: May Not Occur XX
Section 6 - HEALTH HAZARD DATA:
Route(s) of Entry: Inhalation: Yes Skin: NO Ingestion: LD50 = 12.2cc/kg
Health Hazards (Acute and Chronic): (mice)
Acute - Irritates eyes, mucous membranes.
Chronic - No residual effects of acute properties.
MATERIAL SAFETY DATA SHEET Super Glue Gel Revision #7 Page 2 of 2
Carcinogenicity: NTP: No IARC Monographs: No OSHA Regulated: No
First Aid Procedures:
Eye contact - Tearing from eye irritation. Remove to fresh air. Flush areas of contact with water.
Adhesive will disassociate from eye/eyelids over time, usually within several hours. Temporary weeping of eyes/double vision may be experienced until clearance is achieved.
Skin contact - Immerse bonded areas in warm, soapy water. Peel or roll skin apart. Remove cured adhesive with several applications of warm, soapy water. Prolonged or repeated contact at elevated levels may cause dermatitis in sensitive individuals.
Inhalation - Irritation of mucous membranes/coughing. Remove to fresh air. Prolonged or repeated exposure at elevated levels may produce allergic reactions with asthma-like symptoms in sensitive individuals.
Ingestion - Lips may become stuck together: apply copious amounts of warm water & encourage wetting/pressure from saliva inside mouth. Peel or roll (do not pull) lips apart. It is almost impossible to swallow cyanoacrylate as adhesive solidifies upon contact with saliva & may adhere to inside of mouth. Saliva will lift adhesive in 1-2 days, avoid swallowing adhesive after detachment.
Medical Conditions Generally Aggravated by Exposure: Pre-existing skin, eye and respiratory disorders may be aggravated by exposure.
Section 7 - PRECAUTIONS FOR SAFE HANDLING AND USE:
Steps to be taken in Case Material is Released or Spilled: Polymerize with water. Solid material may be scraped from surface.
Waste Disposal Method: Incinerate solid combustible waste or dump as chemical waste according to local, state and federal regulations.
Precautions to Be Taken in Handling and Storing: Avoid contact with clothing as contact can cause burn. Avoid moisture, direct UV-sunlight and do not store above 25 C. Keep containers closed tightly when not in use. Ideal storage: 5-10 C.
Other Precautions: Avoid breathing vapor, contact with eyes/skin. Allow product to reach room temperature before use.
Section 8 - CONTROL MEASURES:
Respiratory Protection (Specify Type): A NIOSH-approved organic vapor canister may be used to maintain vapor concentration below TLV.
Ventilation: Local Exhaust: To maintain vapor concentration below TLV.
Mechanical (General): Large amounts used to 0.2ppm.
Protective Clothing or Equipment: Safety glasses with side shield, Vinyl (polyethylene) non-sticking gloves, rubber apron to protect clothing.
Work/Hygienic Practices: Soap and water helps remove adhesive from skin.
NE = Not established
The data contained herein is based upon information that Pacer Technology believes to be reliable.
Users of this product have the responsibility to determine the suitability of use and to adopt all necessary precautions to ensure the safety and protection of property and persons involved in said use. All statements or suggestions are made without warranty, express or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof.
MATERIAL SAFETY DATA SHEET
05/15/08
Revision #9
Section 1 HAZARD RATING For Chemical Emergency Only:
PACER TECHNOLOGY In the US & Canada (800) 424-9300
9420 Santa Anita Avenue 2 Int'l & Wash DC (COLLECT) (703) 527-3887
Rancho Cucamonga, CA 91730 1 x 1 Telephone for Information :(909) 987-0550
PRODUCT IDENTIFICATION: Super Glue
Section 2 - HAZARDOUS INGREDIENTS INFORMATION:
Hazardous Components OSHA ACGIH OTHER %
(Common Names, CAS Number) PEL TLV LIMITS OPTION
Ethyl-2-Cyanoacrylate (7085-85-0) NE NE 0.2ppm TWA 60-100
Poly (Methyl Methacrylate) (9011-14-7) NE NE 10-30
Hydroquinone* (123-31-9) 2mg/m3 2mg/m3 0-1
*This ingredient is subject to the reporting requirements of Section 313 of Title III of the Superfund
Amendments & Reauthorization Act of 1986 (SARA) and 40 CFR 372.
Section 3 - PHYSICAL/CHEMICAL CHARACTERISTICS:
Boiling Point: 365 F Specific Gravity (H2O=1): 1.05
Vapor Density (Air=1): nil-NE Melting Point: NE
Vapor Pressure (mm Hg): 1 @ 20 C Evaporation Rate (Butyl acetate=1): nil-NE
Solubility in Water: Insoluble, material reacts to hardened mass for non-hazardous waste.
VOC: This product is VOC compliant for sale in California.
Appearance & Odor: Transparent water-white to straw colored liquid with stimulative odor.
Section 4 - FIRE AND EXPLOSION HAZARD DATA:
Flash Point (Method Used): 185 F (TCC) Flammable Limits: LEL: NE UEL: NE
Extinguishing Media: Flush with large amounts of water or dry chemical extinguisher.
Special Fire Fighting Procedures: Fumes may be irritating if not burning and require air supply with goggles while applying large amounts of water or dry chemical extinguisher.
Unusual Fire and Explosion Hazards: None. Combustible requiring the above procedures.
Section 5 - REACTIVITY DATA:
Stability: Stable XX Conditions to Avoid: Excessive heat above 176 F, moisture and alkalines. Stable up to 122 F. Store in a cool dry place.
Incompatibility (Materials to Avoid): Polymerized by water, alcohol, amines, alkaline materials and direct UV.
Hazardous Decomposition Products: Combustible by-products of carbon monoxide/dioxide.
Hazardous Polymerization: May Not Occur XX
Section 6 - HEALTH HAZARD DATA:
Route(s) of Entry: Inhalation: Yes Oral LD50 = > 5000 mg/kg (estimated)
Dermal LD50 = > 2000 mg/kg (estimated)
Health Hazards (Acute and Chronic):
Acute - Irritates eyes, mucous membranes.
Chronic - No residual effects of acute properties.
MATERIAL SAFETY DATA SHEET Super Glue Revision #9 Page 2 of 2
Carcinogenicity: NTP: No IARC Monographs: No OSHA Regulated: No
First Aid Procedures:
Eye contact - Tearing from eye irritation. Remove to fresh air. Flush areas of contact with water.
Adhesive will disassociate from eye/eyelids over time, usually within several hours. Temporary weeping of eyes/double vision may be experienced until clearance is achieved.
Skin contact - Immerse bonded areas in warm, soapy water. Peel or roll skin apart. Remove cured adhesive with several applications of warm, soapy water. Prolonged or repeated contact at elevated levels may cause dermatitis in sensitive individuals.
Inhalation - Irritation of mucous membranes/coughing. Remove to fresh air. Prolonged or repeated exposure at elevated levels may produce allergic reactions with asthma-like symptoms in sensitive individuals.
Ingestion - Lips may become stuck together: apply copious amounts of warm water & encourage wetting/pressure from saliva inside mouth. Peel or roll (do not pull) lips apart. It is almost impossible to swallow cyanoacrylate as adhesive solidifies upon contact with saliva & may adhere to inside of mouth. Saliva will lift adhesive in 1-2 days, avoid swallowing adhesive after detachment.
Medical Conditions Generally Aggravated by Exposure: Pre-existing skin, eye and respiratory
disorders may be aggravated by exposure.
Section 7 - PRECAUTIONS FOR SAFE HANDLING AND USE:
Steps to Be taken in Case Material is Released or Spilled: Polymerize with water. Solid material may be scraped from surface.
Waste Disposal Method: Incinerate solid combustible waste or dump as chemical waste according to local, state and federal regulations.
Precautions to Be Taken in Handling and Storing: Avoid contact with clothing as contact can cause burn. Avoid moisture, direct UV-sunlight and do not store above 25 C. Keep containers closed tightly when not in use. Ideal storage: 5-10 C.
Other Precautions: Avoid breathing vapor, contact with eyes/skin. Allow product to reach room temperature before use.
Section 8 - CONTROL MEASURES:
Respiratory Protection (Specify Type): A NIOSH-approved organic vapor canister may be used to maintain vapor concentration below TLV.
Ventilation: Local Exhaust: To maintain vapor concentration below TLV.
Mechanical (General): Large amounts used to 0.2ppm.
Protective Clothing or Equipment: Safety glasses with side shield, Vinyl (polyethylene) non-sticking gloves, rubber apron to protect clothing.
Work/Hygienic Practices: Soap and water helps remove adhesive from skin.
Section 9 - OTHER: Super Glue - Not regulated for transportation.
NE = Not established
The data contained herein is based upon information that Pacer Technology believes to be reliable.
Users of this product have the responsibility to determine the suitability of use and to adopt all necessary precautions to ensure the safety and protection of property and persons involved in said use. All statements or suggestions are made without warranty, express or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof.
MATERIAL SAFETY DATA SHEET
03/03/08
Rev 1
Section 1: For Chemical Emergency Only:
PACER TECHNOLOGY In the US & Canada (800) 424-9300
9420 Santa Anita Avenue Int'l & Wash DC (COLLECT) (703) 527-3887
Rancho Cucamonga, CA 91730 Telephone for Information: (909) 987-0550
PRODUCT IDENTIFICATION: HAZARD RATING 1
Z-Poxy 5 Minute Quick Shot Epoxy - Resin - Part A (PT36) 2 x 0
Section 2 - HAZARDOUS INGREDIENTS INFORMATION:
Hazardous Components OSHA ACGIH OTHER %
(Common Names, CAS Number) PEL TLV LIMITS OPTION
Bisphenol A/Epichlorohydrin: based epoxy resin* (25068-38-6) NE NE NE 60-100%
* This product is an epoxy resin produced by the condensation reaction of Epichlorohydrin and Bisphenol-A. These raw materials are consumed in the process. Residual levels of Epichlorohydrin are controlled to 1ppm, max., in the product.
Section 3 - PHYSICAL/CHEMICAL CHARACTERISTICS:
Boiling Point: >500F Specific Gravity (H2O=1): 1.17
Vapor Density (Air=1): NA Melting Point: NE
Vapor Pressure (mm Hg): 0.03 @ 77F Evaporation Rate (Butyl Acetate = 1): NA
Solubility in Water: Negligible.
Appearance & Odor: Light yellow colored viscous liquid.
Section 4 - FIRE AND EXPLOSION HAZARD DATA:
Flash Point (Method Used): 480F (PMCC) Flammable Limits: LEL: NE UEL: NE
Extinguishing Media: Water fog, foam, dry chemical or carbon dioxide.
Special Fire Fighting Procedures: Material will not burn unless preheated. Do not enter confined fire space without full bunker gear (helmet/face shield, bunker coat, gloves & rubber boats). Use positive pressure NIOSH-approved self-contained breathing apparatus. Cool fire exposed containers with water.
Unusual Fire and Explosion Hazards: Heating of resin above 300F in presence of air may cause slow oxidative decomposition. Above 500F polymerization may occur. Some curing agents, e.g. aliphatic amines can produce exothermic reactions which in large masses can cause runaway polymerization & charring of reactants. Fumes & vapors from these thermal & chemical decompositions vary widely in composition/toxicity. DO NOT BREATHE FUMES. Unidentified fumes & vapors may be toxic.
Section 5 - REACTIVITY DATA:
Stability: Stable XX Conditions to Avoid: Keep away from open flames & high temperatures.
Incompatibility (Materials to Avoid): Strong oxidizing agents, strong Lewis or mineral acids, strong mineral & organic bases, esp. primary & secondary aliphatic amines.
Hazardous Decomposition Products: Carbon monoxide, aldehydes, acids & other organic substances may be formed during combustion (>500F) temperature degradation.
Hazardous Polymerization: May Occur __ May Not Occur XX (Avoid heating >300F).
Section 6 - HEALTH HAZARD DATA:
Route(s) of Entry: Inhalation: YES Skin: YES Ingestion: YES
Health Hazards (Acute and Chronic):
Product moderately irritating to eyes, skin; contact with product at elevated temperatures can result in thermal burns; may cause skin sensitization; low order of acute oral toxicity noted; unlikely to be inhalation hazard due to low volatility.
Carcinogenicity: NTP: No IARC Monographs: No OSHA Regulated: No
Signs and Symptoms of Exposure & First Aid Procedures:
Eye contact - irritation: flush eyes with copious amounts of water for 15 min. while holding eyes open. Get medical attention immediately.
Skin contact - irritation/rash: remove contaminated clothing and wash with soap/water. Get medical attention if symptoms persist (contaminated leather articles i.e. shoes should be disposed of as contaminated waste). NOTE: hot product burns require immediate medical attention.
Inhalation - Remove to fresh air and provide oxygen if breathing is difficult. Get medical attention.
Ingestion - Do not induce vomiting. In general, no treatment, unless large amount is ingested, however, get medical advice.
NOTE TO PHYSICIAN: Emesis induction is normally not necessary in high viscosity, low volatility products, e.g. neat epoxy resins.
Medical Conditions Generally Aggravated by Exposure: Pre-existing eye/skin disorders or lung allergies.
Section 7 - PRECAUTIONS FOR SAFE HANDLING AND USE:
Steps to Be taken in Case Material is Released or Spilled: Product may burn although not readily ignitable. Use cautious judgment when cleaning up large spills, respirator and protective equipment as appropriate. Dike and contain material. Soak up residue with absorbent (clay, sand) materials and dispose of properly.
Waste Disposal Method: If product becomes waste, not considered hazardous waste by RCRA criteria (40 CFR 261). Dispose of according to federal, state and local regulations.
Precautions to Be Taken in Handling and Storing: Store in cool, dry place away from open flames and high temperatures.
Other Precautions: Empty containers may contain product residues & should be disposed of properly.
Section 8 - CONTROL MEASURES:
Respiratory Protection (Specify Type): Organic vapor respirator in areas with poor ventilation.
Ventilation: Local Exhaust: Good Mechanical (General): As needed.
Protective Clothing or Equipment: Safety glasses/goggles with side shields, chemically resistant gloves and other protective equipment to avoid direct contact.
Work/Hygienic Practices: Avoid contact with eyes or skin. Use in well ventilated area. Wash hands with soap and water after product use. Launder contaminated clothing before reuse and disposed of leather articles as contaminated waste.
NA = Not applicable
NE = Not established
The data contained herein is based upon information that Pacer Technology believes to be reliable.
Users of this product have the responsibility to determine the suitability of use and to adopt all necessary precautions to ensure the safety and protection of property and persons involved in said use. All statements or suggestions are made without warranty, express or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof.
MATERIAL SAFETY DATA SHEET
03/03/08
Rev. 1
Section 1: HAZARD RATING For Chemical Emergency Only:
PACER TECHNOLOGY 1 In the US & Canada (800) 424-9300
9420 Santa Anita Avenue 2 X 1 Int'l & Wash DC (COLLECT) (703) 527-3887
Rancho Cucamonga, CA 91730 Telephone for Information: (909) 987-0550
PRODUCT IDENTIFICATION: Z-Poxy 5 Min. Quick Shot Epoxy - Hardener - Part B
(PT36)
Section 2: HAZARDOUS INGREDIENTS INFORMATION:
Hazardous Components OSHA ACGIH OTHER %
(Common Names, CAS Number) PEL TLV LIMITS OPTION
Proprietary Mercaptan Polymer NE NE 60-100
Tertiary Amine (90-72-2) NE NE 1-5
Note: Proprietary Mercaptan Polymer does not contain any ingredients subject to the reporting requirements of Section 313, Title III, part 372.
Section 3 - PHYSICAL/CHEMICAL CHARACTERISTICS:
Boiling Point: NE Specific Gravity (H2O=1): 1.13
Vapor Density (Air=1): NE Melting Point: NE
Vapor Pressure (mm Hg): NE Evaporation Rate (Butyl acetate = 1): NE
Solubility in Water: Slightly soluble.
Appearance & Odor: Light colored transparent syrup with mild sulfur odor.
Section 4 - FIRE AND EXPLOSION HAZARD DATA:
Flash Point (Method): 300 F (TCC) Flammable Limits: LEL: NE UEL: NE
Extinguishing Media: Water spray, carbon dioxide, foam or dry chemical.
Special Fire Fighting Procedures: Cool exposed containers with water spray. Wear self-contained breathing apparatus in confined areas.
Unusual Fire and Explosion Hazards: None known.
Section 5 - REACTIVITY DATA:
Stability: Stable XX Conditions to Avoid: Storage near large masses of epoxy resins.
Incompatibility (Materials to Avoid): Strong oxidants, amines especially when hot.
Hazardous Decomposition Products: Carbon monoxide/dioxide, hydrogen sulfide and oxides of sulfur.
Hazardous Polymerization: May Occur __ May Not Occur XX
Section 6 - HEALTH HAZARD DATA:
Route(s) of Entry: Inhalation: Yes Skin: Yes Ingestion: Yes
Health Hazards (Acute and Chronic):
Acute - irritates skin, eye & respiratory tract.
Chronic - May aggravate pre-existing skin/eye/lung conditions.
Carcinogenicity: NTP: No IARC Monographs: No OSHA Regulated: No
Signs and Symptoms of Exposure & First Aid Procedures:
Eye contact - Irritation: immediately flush eye with copious amounts of water for 15 minutes. Get medical attention.
Skin contact - Irritation upon direct contact. Remove contaminated clothing and wash affected areas with soap and water.
Inhalation - Remove to fresh air. Administer oxygen if available.
Ingestion - Do not induce vomiting. Keep airway clear if vomiting occurs.
Medical Conditions Generally Aggravated by Exposure: Pre-existing skin/eye/lung conditions.
Section 7 - PRECAUTIONS FOR SAFE HANDLING AND USE:
Steps to Be taken in Case Material is Released or Spilled: Stop leaks & contain spill. Soak up with absorbent material for disposal in proper container, wearing adequate protective clothing/respiratory protection.
Waste Disposal Method: In chemical landfill or incinerate in accordance with federal, state or local regulations.
Precautions to Be Taken in Handling and Storing: Do not store near epoxy resin, protect containers to avoid leaks and spills.
Other Precautions: CAUTION - May cause irritation. Avoid direct contact or breathing of mist or vapor. Use with adequate ventilation and use respiratory protection where mist or vapor may be generated. For industrial use only, keep containers closed when not in use.
Section 8 - CONTROL MEASURES:
Respiratory Protection (Specify Type): Organic vapor respirator to avoid inhalation of mist or vapor.
Ventilation: Local Exhaust: Good Mechanical (General): As needed.
Protective Clothing or Equipment: Safety glasses/goggles with side shields, rubber gloves, chemical resistant shoes and protective clothing to avoid direct contact.
Work/Hygienic Practices: Avoid direct contact or breathing of mist or vapor. Use with adequate ventilation. Wash hands with soap and water after use. Launder contaminated clothing before reuse. Do not take internally.
NE = Not established
The data contained herein is based upon information that Pacer Technology believes to be reliable.
Users of this product have the responsibility to determine the suitability of use and to adopt all necessary precautions to ensure the safety and protection of property and persons involved in said use. All statements or suggestions are made without warranty, express or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof.
MATERIAL SAFETY DATA SHEET
03/03/08
Revision #3
Section 1 For Chemical Emergency Only:
PACER TECHNOLOGY HAZARD RATING In the US & Canada (800) 424-9300
9420 Santa Anita Avenue 1 Int'l & Wash DC (COLLECT) (703) 527-3887
Rancho Cucamonga, CA 91730 2 x 0 Telephone for Information: (909) 987-0550
PRODUCT IDENTIFICATION: Z-Poxy 30 Minute Formula - Resin - Part A
Section 2 - HAZARDOUS INGREDIENTS INFORMATION:
Hazardous Components OSHA ACGIH OTHER %
(Common Names, CAS Number) PEL TLV LIMITS OPTION
Bisphenol A/Epichlorohydrin: based epoxy resin* (25068-38-6) NE NE NE 60-100%
* This product is an epoxy resin produced by the condensation reaction of Epichlorohydrin and
Bisphenol-A. These raw materials are consumed in the process. Residual levels of Epichlorohydrin are controlled to 1ppm, max, in the product.
Section 3 - PHYSICAL/CHEMICAL CHARACTERISTICS:
Boiling Point: >500F Specific Gravity (H2O=1): 1.17
Vapor Density (Air=1): NA Melting Point: NE
Vapor Pressure (mm Hg): 0.03 @ 77F Evaporation Rate (Butyl Acetate = 1): NA
Solubility in Water: Negligible.
Appearance & Odor: Light yellow colored viscous liquid.
Section 4 - FIRE AND EXPLOSION HAZARD DATA:
Flash Point (Method Used): 480F (PMCC) Flammable Limits: LEL: NE UEL: NE
Extinguishing Media: Water fog, foam, dry chemical or carbon dioxide.
Special Fire Fighting Procedures: Material will not burn unless preheated. Do not enter confined fire space without full bunker gear (helmet/face shield, bunker coat, gloves & rubber boats). Use positive pressure NIOSH-approved self-contained breathing apparatus. Cool fire exposed containers with water.
Unusual Fire and Explosion Hazards: Heating of resin above 300F in presence of air may cause slow oxidative decomposition. Above 500F polymerization may occur. Some curing agents, e.g. aliphatic amines can produce exothermic reactions which in large masses can cause runaway polymerization & charring of reactants. Fumes & vapors from these thermal & chemical decompositions vary widely in composition/toxicity. DO NOT BREATHE FUMES. Unidentified fumes & vapors may be toxic.
Section 5 - REACTIVITY DATA:
Stability: Stable XX Conditions to Avoid: Keep away from open flames & high temperatures.
Incompatibility (Materials to Avoid): Strong oxidizing agents, strong Lewis or mineral acids, strong mineral & organic bases, esp. primary & secondary aliphatic amines.
Hazardous Decomposition Products: Carbon monoxide, aldehydes, acids & other organic substances may be formed during combustion (>500F) temperature degradation.
Hazardous Polymerization: May Occur __ May Not Occur XX (Avoid heating >300F).
Section 6 - HEALTH HAZARD DATA:
Route(s) of Entry: Inhalation: YES Skin: YES Ingestion: YES
Health Hazards (Acute and Chronic):
Product moderately irritating to eyes, skin; contact with product at elevated temperatures can result in thermal burns; may cause skin sensitization; low order of acute oral toxicity noted; unlikely to be inhalation hazard due to low volatility.
Carcinogenicity: NTP: No IARC Monographs: No OSHA Regulated: No
First Aid Procedures:
Eye contact - irritation: flush eyes with copious amounts of water for 15 min. while holding eyes open. Get medical attention immediately.
Skin contact - irritation/rash: remove contaminated clothing and wash with soap/water. Get medical attention if symptoms persist (contaminated leather articles i.e. shoes should be disposed of as contaminated waste). NOTE: hot product burns require immediate medical attention.
Inhalation - Remove to fresh air and provide oxygen if breathing is difficult. Get medical attention.
Ingestion - Do not induce vomiting. In general, no treatment unless large amount is ingested, however, get medical advice.
NOTE TO PHYSICIAN: Emesis induction is normally not necessary in high viscosity, low volatility products, e.g. neat epoxy resins.
Medical Conditions Generally Aggravated by Exposure: Pre-existing eye/skin disorders or lung allergies.
Section 7 - PRECAUTIONS FOR SAFE HANDLING AND USE:
Steps to Be taken in Case Material is Released or Spilled: Product may burn although not readily ignitable. Use cautious judgment when cleaning up large spills. Respirator and protective equipment as appropriate. Dike and contain material. Soak up residue with absorbent (clay, sand) materials and dispose of properly.
Waste Disposal Method: If product becomes waste, not considered hazardous waste by RCRA criteria (40 CFR 261). Dispose of according to federal, state and local regulations.
Precautions to Be Taken in Handling and Storing: Store in cool, dry place away from open flames and high temperatures.
Other Precautions: Empty containers may contain product residues & should be disposed of properly.
Section 8 - CONTROL MEASURES:
Respiratory Protection (Specify Type): Organic vapor respirator in areas with poor ventilation.
Ventilation: Local Exhaust: Good Mechanical (General): As needed.
Protective Clothing or Equipment: Safety glasses/goggles with side shields, chemically resistant gloves and other protective equipment to avoid direct contact.
Work/Hygienic Practices: Avoid contact with eyes or skin. Use in well ventilated area. Wash hands with soap and water after product use. Launder contaminated clothing before reuse and disposed of leather articles as contaminated waste.
Section 9 - OTHER: Not restricted for transportation
NA = Not applicable
NE = Not established
The data contained herein is based upon information that Pacer Technology believes to be reliable. Users of this product have the responsibility to determine the suitability of use and to adopt all necessary precautions to ensure the safety and protection of property and persons involved in said use. All statements or suggestion are made without warranty, express or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof.
MATERIAL SAFETY DATA SHEET
03/03/08
Revision #5
Section 1.For Chemical Emergency Only:
PACER TECHNOLOGY HAZARD RATING In the US & Canada (800) 424-9300
9420 Santa Anita Avenue 1 Int'l & Wash DC (COLLECT) (703) 527-3887
Rancho Cucamonga, CA 91730 3 x 1 Telephone for Information: (909) 987-0550
PRODUCT IDENTIFICATION: Z-Poxy 30 Minute Formula - Hardener - Part B
Section 2 - HAZARDOUS INGREDIENTS INFORMATION:
Hazardous Components OSHA ACGIH OTHER %
(Common Names, CAS Number) PEL TLV LIMITS OPTION
Proprietary Mercaptan Polymer NE NE NE 60-100
Tertiary Amine (90-72-2) NE NE NE 5-10
Tris (Dimethyl Aminomethy) Phenol Trihexoate NE NE NE 1-5
+ This ingredient is subject to the reporting requirements of Section 313 of Title III of the Superfund
Amendments & Reauthorization Act of 1986 (SARA) and 40 CFR 372.
Section 3 - PHYSICAL/CHEMICAL CHARACTERISTICS:
Boiling Point: NE Specific Gravity (H2O=1): 1.13
Vapor Density (Air=1): NE Melting Point: NA
Vapor Pressure (mm Hg): NE Evaporation Rate (Butyl acetate = 1): NE
Solubility in Water: Slightly soluble.
Appearance & Odor: Viscous water white to light yellow liquid with mercaptan odor.
Section 4 - FIRE AND EXPLOSION HAZARD DATA:
Flash Point (Method): 300 F (TCC) Flammable Limits: LEL: NE UEL: NE
Extinguishing Media: Water spray, carbon dioxide, foam or dry chemical.
Special Fire Fighting Procedures: Cool exposed containers with water spray. Wear self-contained breathing apparatus in confined areas.
Unusual Fire and Explosion Hazards: None known.
Section 5 - REACTIVITY DATA:
Stability: Stable XX Conditions to Avoid: Storage near large masses of epoxy resins.
Incompatibility (Materials to Avoid): Strong oxidants, amines especially when hot.
Hazardous Decomposition Products: Carbon monoxide/dioxide, hydrogen sulfide and oxides of sulfur.
Hazardous Polymerization: May occur __ May Not Occur XX
Section 6 - HEALTH HAZARD DATA:
Route(s) of Entry: Inhalation: Yes Skin: Yes Ingestion: Yes
Health Hazards (Acute and Chronic):
Acute - irritates skin, eye & respiratory tract.
Chronic - May aggravate pre-existing skin/eye/lung conditions.
Carcinogenicity: NTP: No IARC Monographs: No OSHA Regulated: No
First Aid Procedures:
Eye contact - Irritation: immediately flush eye with copious amounts of water for 15 minutes. Get medical attention.
Skin contact - Irritation upon direct contact, remove contaminated clothing and wash affected areas with soap and water.
Inhalation - Remove to fresh air. Administer oxygen if available.
Ingestion - Do not induce vomiting. Keep airway clear if vomiting occurs.
Medical Conditions Generally Aggravated by Exposure: Pre-existing skin/eye/lung conditions.
Section 7 - PRECAUTIONS FOR SAFE HANDLING AND USE:
Steps to be taken in Case Material is Released or Spilled: Stop leaks & contain spill. Soak up with absorbent material for disposal in proper container, wearing adequate protective clothing/respiratory protection.
Waste Disposal Method: In chemical landfill or incinerate in accordance with federal, state or local regulations.
Precautions to Be Taken in Handling and Storing: Do not store near epoxy resin, protect containers to avoid leaks and spills.
Other Precautions: CAUTION - May cause irritation. Avoid direct contact or breathing of mist or vapor. Use with adequate ventilation and use respiratory protection where mist or vapor may be generated. For industrial use only. Keep containers closed when not in use.
Section 8 - CONTROL MEASURES:
Respiratory Protection (Specify Type): Organic vapor respirator to avoid inhalation of mist or vapor.
Ventilation: Local Exhaust: Good Mechanical (General): As needed.
Protective Clothing or Equipment: Safety glasses/goggles with side shields, rubber gloves, chemical resistant shoes and protective clothing to avoid direct contact.
Work/Hygienic Practices: Avoid direct contact or breathing of mist or vapor. Use with adequate ventilation. Wash hands with soap and water after use. Launder contaminated clothing before reuse.
Do not take internally.
Section 9 - OTHER: Not restricted for transportation
NE = Not established
The data contained herein is based upon information that Pacer Technology believes to be reliable.
Users of this product have the responsibility to determine the suitability of use and to adopt all necessary precautions to ensure the safety and protection of property and persons involved in said use. All statements or suggestions are made without warranty, express or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof.
MATERIAL SAFETY DATA SHEET
Kwik Epoxy Steel Resin VC-6
J-B Weld Company
P.O. Box 483
1130 Como Street
Sulphur Springs, TX 75482
Tel: (903) 885-7696
Fax: (903) 885-5911
SECTION I - IDENTIFICATION OF PRODUCT
PRODUCT NAME: J B WELD KWIK EPOXY STEEL RESIN - VC-6 PART A
PRODUCT CODE: (48009), 48149, 48151, 48177, 48190
REFERENCE: Resin Solution
SCHEDULE B NUMBER: 3506.91.0000
SECTION II - HAZARDOUS INGREDIENTS
INGREDIENTS WGT% CAS # TLV/PEL
Calcium Carbonate 40-50% 1317-65-3 ACGIH TLV: 10 mg/m3
OSHA: PEL 15 mppcf
Iron Powder 10-20% 65997-19-5 ACGIH TLV: 15 mg/m3
OSHA: PEL 15 mppcf
Epoxy Resin 30-40% 25068-38-6 N/E
Aromatic Hydrocarbons 1-5 % 64742-94-5 N/E
SECTION III - PHYSICAL DATA
APPEARANCE: Dark gray or black smooth paste
SPECIFIC GRAVITY: 1.80
VAPOR PRESSURE (mmHG): N/Av
BOILING POINT: N/E
VAPOR DENSITY (Air = 1): >1
EVAPORATION RATE (Ethyl Ether = 1): Slower than Ethyl Ether
VOLATILES BY WEIGHT: N/D
SOLUBILITY IN WATER: Not soluble
VOC: Grams/Liter = Nil
Lbs/Gallon = Nil
SECTION IV - FIRE AND EXPLOSION DATA
FLASH POINT: >200®F/93®C Seta Flash Closed cup
LOWER FLAMMABLE LIMIT %: N/E
UPPER FLAMMABLE LIMIT %: N/E
FIRE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES: Fight like a fuel oil fire. Cool fire exposed containers with water spray. Firefighter should wear OSHA/NIOSH approved self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARD: Closed containers exposed to high temperatures, such as fire conditions may rupture.
SECTION V - HEALTH HAZARD/TOXICOLOGICAL PROPERTIES
OVEREXPOSURE EFFECTS:
ACUTE EFFECTS:
EYES: Contact with eyes can cause severe irritation, possible irreparable eye damage.
SKIN: Contact with skin can cause irritation, (minor itching, burning and/or redness), Dermatitis,
defatting may be readily absorbed through the skin.
INHALATION: Inhalation of vapors can cause nasal and respiratory irritation, dizziness, weakness, fatigue, nausea, headache, possible unconsciousness and/or asphyxiation. Aspiration of material into lungs may result in chemical pneumonitis which can be fatal.
INGESTION: Ingestion can cause gastrointestinal irritation, nausea, vomiting, diarrhea.
CHRONIC EFFECTS:
Overexposure to this material has apparently been known to cause the following effects in lab animals: lung damage and/or allergic reaction
CARCINOGEN: YES _____ NO __X__
TERATOGEN: YES _____ NO __X__
MUTAGEN: YES _____ NO __X__
ROUTES OF EXPOSURE: skin, inhalation
FIRST AID:
INHALATION: If inhaled, remove victim from exposure to a well-ventilated area. Make them comfortably warm, but not hot. Use oxygen or artificial respiration as required. Consult a physician.
SKIN: For skin contact, wash promptly with soap and excess water.
EYES: For eye contact, flush promptly with excess water for at least fifteen minutes. Consult a physician.
INGESTION: If ingested, do not induce vomiting. Give victim a glass of water. Call a physician immediately.
SECTION V I - REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Open flames, sparks, and heat.
INCOMPATIBILITY MATERIALS TO AVOID: Strong acids, alkalis, oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Dioxide, Carbon Monoxide and Carbon.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION VII - SPILL AND DISPOSAL PROCEDURE
SPILLS, LEAK OR RELEASE: Ventilate area. Remove all possible sources of ignition. Avoid prolonged breathing of vapor. Contain spill with inert absorbent.
WASTE DISPOSAL: Dispose of in accordance with local, state, and federal regulations.
SECTION VIII - PROTECTION INFORMATION
RESPIRATORY PROTECTION: If component TLV limits are exceeded, use NIOSH/MSHA approved respirator to remove vapors. Use an air-supplied respirator if necessary. With general ventilation, does not require a respirator.
VENTILATION: Use adequate ventilation in volume and pattern to keep TLV/PEL below recommended levels.
Explosion-proof ventilation may be necessary.
PROTECTIVE GLOVES: To prevent prolonged exposure use rubber gloves; solvents may be absorbed through the skin
EYE PROTECTION: Safety Glasses or goggles with splash guards or side shields.
OTHER PROTECTIVE EQUIPMENT: Wear protective clothing as required to prevent skin contact.
SECTION IX - HANDLING AND STORAGE PRECAUTIONS
STORAGE AND HANDLING: Use with adequate ventilation. Avoid contact with eyes and skin. Avoid breathing vapors. Do not store the product above 100®F/38®C. Do not flame, cut, braze weld or melt empty containers. Keep the product away from heat, open flame, and other sources of ignition. Avoid contact with strong acids, alkalis and oxidizers.
SECTION X - ADDITIONAL INFORMATION
SHIPPING INFORMATION: Please comply with DOT regulations in USA
HMIS RATING: Health 2 4 = Extreme
Fire 1 3 = High
Reactivity 1 2 = Moderate
1 = Slight
0 = Insignificant
Personal Protection - See Section VIII
CALIFORNIA PROPOSITION 65:
Trace amounts of epichlorohydrin, a chemical known to the State of California to cause cancer, is present in this product. However, given the low level and application of this product, typical uses do not constitute a significant risk under the standard.
SECTION 313 SUPPLIER NOTIFICATION:
This product contains the following toxic chemicals subject to the reporting requirements of the Emergency
Planning and Community Right-To-Know Act of 1986 and 40 CFR 372:
CHEMICAL NAME CAS % BY WGT
N/Ap
THIS INFORMATION MUST BE INCLUDED IN ALL MSDS THAT ARE COPIED AND DISTRIBUTED FOR THIS CHEMICAL
ABBREVIATIONS
IARC = International Agency for Research on Cancer
ACGIH = American Conference of Governmental Industrial Hygienists
NIOSH = National Institute of Occupational Safety and Health
TLV = Threshold Limit Value
PEL = Permissible Emission Level
DOT = Department of Transportation
NTP = National Toxicology Program
N/AV = Not Available
N/AP = Not Applicable
N/E = Not Established
N/D = Not Determined
PREPARED FOR: J-B Weld Company
P.O. Box 483
1130 Como Street
Sulphur Springs, TX 75482
Tel: (903) 885-7696
Fax: (903) 885-5911
REVIEWED ON May 17, 2004
SUPERSEDES March 1, 2003
REVISION Format
The information in the Material Safety Data Sheet has been compiled from our experience and from data presented in various technical publications. It is the user’s responsibility to determine the suitability of this information for the adoption of the safety precautions as may be necessary. We reserve the right to revise
Material Safety Data Sheets from time to time as new technical information becomes available. The user has the responsibility to contact the Company to make sure that the MSDS is the latest one issued.
MATERIAL SAFETY DATA SHEET
Kwik Epoxy Steel VC-6 Hardener – Part B
J-B Weld Company
P.O. Box 483
1130 Como Street
Sulphur Springs, TX 75482
Tel: (903) 885-7696
Fax: (903) 885-5911
SECTION I - IDENTIFICATION OF PRODUCT
PRODUCT NAME: J B WELD KWIK EPOXY STEEL HARDENER - PART B
PRODUCT CODE: (48094), 48148, 48150, 48178, 48191
REFERENCE: Epoxy Steel Hardener
SCHEDULE B NUMBER: 3214.10.0090
SECTION II - HAZARDOUS INGREDIENTS
INGREDIENTS WGT% CAS # TLV/PEL
Calcium Carbonate 5-10% 1317-65-3 ACGIH TWA 10 mg/m3
471-34-1 OSHA PEL 15 mppcf
Non-fibrous Talc 15-25% 14807-96-6 ACGIH TWA 2 mg/m3
OSHA PEL 20 mppcf
Barium Sulfate 35-45% 7727-43-7 ACGIH TWA 10 mg/m3
OSHA 15 mg/m3 Total dust
OSHA 15 mg/m3 Respirable dust
Alkyl Phenol 1-5 % 25154-52-3 N/E
Mercaptan terminated polymer 20-30% Trade Secret NE
2,4,6 [(Dimethylamino)methyl] phenol 1-5 % 90-72-2 N/E
Amorphous Silica 1-5 % 112945-52-5 ACGIH TWA 10 mg/m3
5 mg/m3 (respirable)
SECTION III - PHYSICAL DATA
APPEARANCE: White paste
SPECIFIC GRAVITY: 1.87
VAPOR PRESSURE (mmHG): N/Av
BOILING POINT: N/E
VAPOR DENSITY: Heavier than air
EVAPORATION RATE (Ethyl Ether = 1): Slower than Ethyl Ether
VOLATILES BY WEIGHT: Nil
SOLUBILITY IN WATER: Not soluble
VOC: Grams/Liter = 4
Lbs/Gallon = 0.03
SECTION IV - FIRE AND EXPLOSION DATA
FLASH POINT: >200°F/93°C Seta Flash Closed cup
LOWER FLAMMABLE LIMIT %: N/E
UPPER FLAMMABLE LIMIT %: N/E
FIRE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES: Fight like a fuel oil fire. Cool fire exposed containers with water
spray. Firefighter should wear OSHA/NIOSH approved self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARD: Closed containers exposed to high temperatures, such as fire conditions may rupture.
SECTION V - HEALTH HAZARD/TOXICOLOGICAL PROPERTIES
OVEREXPOSURE EFFECTS:
ACUTE EFFECTS:
EYES: Contact with eyes can cause severe irritation, possible irreparable eye damage.
SKIN: Contact with skin can cause irritation, (minor itching, burning and/or redness), Dermatitis,
defatting may be readily absorbed through the skin.
INHALATION: Inhalation of vapors can cause nasal and respiratory irritation, dizziness, weakness, fatigue, nausea, headache, possible unconsciousness and/or asphyxiation. Aspiration of material into lungs may result in chemical pneumonitis which can be fatal.
INGESTION: Ingestion can cause gastrointestinal irritation, nausea, vomiting, diarrhea.
CHRONIC EFFECTS:
Overexposure to this material has apparently been known to cause the following effects in lab animals: lung damage and/or allergic reaction
CARCINOGEN: YES _____ NO __X__
TERATOGEN: YES _____ NO __X__
MUTAGEN: YES _____ NO __X__
ROUTES OF EXPOSURE: skin, inhalation
FIRST AID:
INHALATION: If inhaled, remove victim from exposure to a well-ventilated area. Make them comfortably warm, but not hot. Use oxygen or artificial respiration as required. Consult a physician.
SKIN: For skin contact, wash promptly with soap and excess water.
EYES: For eye contact, flush promptly with excess water for at least fifteen minutes. Consult a physician.
INGESTION: If ingested, do not induce vomiting. Give victim a glass of water. Call a physician immediately.
SECTION V I - REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Open flames, and heat.
INCOMPATIBILITY MATERIALS TO AVOID: Strong acids, alkalis, oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Dioxide, Carbon Monoxide and Carbon.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION VII - SPILL AND DISPOSAL PROCEDURE
SPILLS, LEAK OR RELEASE: Ventilate area. Remove all possible sources of ignition. Avoid prolonged breathing of vapor. Contain spill with inert absorbent.
WASTE DISPOSAL: Dispose of in accordance with local, state, and federal regulations.
SECTION VIII - PROTECTION INFORMATION
RESPIRATORY PROTECTION: If component TLV limits are exceeded, use NIOSH/MSHA approved respirator to remove vapors. Use an air-supplied respirator if necessary. With general ventilation, does not require a respirator.
VENTILATION: Use adequate ventilation in volume and pattern to keep TLV/PEL below recommended levels.
Explosion-proof ventilation may be necessary.
PROTECTIVE GLOVES: To prevent prolonged exposure use rubber gloves; solvents may be absorbed through the skin
EYE PROTECTION: Safety Glasses or goggles with splash guards or side shields.
OTHER PROTECTIVE EQUIPMENT: Wear protective clothing as required to prevent skin contact.
SECTION IX - HANDLING AND STORAGE PRECAUTIONS
STORAGE AND HANDLING: Use with adequate ventilation. Avoid contact with eyes and skin. Avoid breathing vapors. Do not store the product above 100°F/38°C. Do not flame, cut, braze weld or melt empty containers. Keep the product away from heat, open flame, and other sources of ignition. Avoid contact with strong acids, alkalis and oxidizers.
SECTION X - ADDITIONAL INFORMATION
SHIPPING INFORMATION: Please comply with DOT regulations in USA
HMIS RATING: Health 2 4 = Extreme
Fire 2 3 = High
Reactivity 2 2 = Moderate
1 = Slight
0 = Insignificant
Personal Protection - See Section VIII
CALIFORNIA PROPOSITION 65:
Trace amounts of some chemicals known to the State of California to cause cancer, birth defects or other reproductive harm may be present in this product.
SECTION 313 SUPPLIER NOTIFICATIONS:
This product contains the following toxic chemicals subject to the reporting requirements of the Emergency
Planning and Community Right-To-Know Act of 1986 and 40 CFR 372:
CHEMICAL NAME CAS % BY WGT
N/Ap
THIS INFORMATION MUST BE INCLUDED IN ALL MSDS THAT ARE COPIED AND DISTRIBUTED FOR THIS CHEMICAL
ABBREVIATIONS
IARC = International Agency for Research on Cancer
ACGIH = American Conference of Governmental Industrial Hygienists
NIOSH = National Institute of Occupational Safety and Health
TLV = Threshold Limit Value
PEL = Permissible Emission Level
DOT = Department of Transportation
NTP = National Toxicology Program
N/AV = Not Available
N/AP = Not Applicable
N/E = Not Established
N/D = Not Determined
PREPARED BY:
J-B Weld Company
P.O. Box 483
1130 Como Street
Sulphur Springs, TX 75482
Tel: (903) 885-7696
Fax: (903) 885-5911
REVIEWED ON May 17, 2004
SUPERSEDES March 1, 2003
REVISION Format
The information in the Material Safety Data Sheet has been compiled from our experience and from data presented in various technical publications. It is the user’s responsibility to determine the suitability of this information for the adoption of the safety precautions as may be necessary. We reserve the right to revise
Material Safety Data Sheets from time to time as new technical information becomes available. The user has the responsibility to contact the Company to make sure that the MSDS is the latest one issued.
MATERIAL SAFETY DATA SHEET
EPOXY STEEL HARDENER
J-B Weld Company
P.O. Box 483
1130 Como Street
Sulphur Springs, TX 75482
Tel: (903) 885-7696
Fax: (903) 885-5911
SECTION I - IDENTIFICATION OF PRODUCT
PRODUCT NAME: J B WELD EPOXY STEEL HARDENER
PRODUCT CODE: (48008), 48105, 48155, 48171
SYNONYM/CROSS REFERENCE: Epoxy Hardener
SCHEDULE B NUMBER: 3506.91.0000-3
SECTION II - HAZARDOUS INGREDIENTS
INGREDIENTS WGT% CAS # TLV/PEL
Calcium Carbonate 30-40% 1317-65-3 ACGIH TWA 10 mg/m3
OSHA PEL 15 mppcf
Barium Sulfate 20-30% 7727-43-7 ACGIH TWA 10 mg/m3
OSHA PEL 2 mppcf
Magnesium Silicate 5-10% 14807-96-6 ACGIH TWA 2 mg/m3
OSHA PEL 20 mppcf
Titanium Dioxide 1-5% 13463-67-7 ACGIH TWA 10 mg/m3
OSHA PEL 20 mg/m3
Zinc Sulfide 0-5% 1314-98-3 ACGIH TLV 10 mg/m3
Furfuryl Alcohol 1-5% 98-00-0 ACGIH TWA 10 ppm
Polyamide Resin 15-25% 68410-23-1 N/E
Aminophenols 1-5 % Mixture N/E
SECTION III - PHYSICAL DATA
APPEARANCE: White Paste
SPECIFIC GRAVITY: 1.78
VAPOR PRESSURE (mmHG): N/Av
BOILING POINT: N/Av
VAPOR DENSITY: Heavier than air
EVAPORATION RATE (Ethyl Ether = 1): Slower than Ethyl Ether
VOLATILES BY WEIGHT: Nil
SOLUBILITY IN WATER: Not Soluble
VOC: Grams/Liter = 72
Lbs/Gallon = 0.6
SECTION IV - FIRE AND EXPLOSION DATA
FLASH POINT: .>200°F/93°C Seta Flash Closed cup
LOWER FLAMMABLE LIMIT %: N/E
UPPER FLAMMABLE LIMIT %: N/E
FIRE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES: Fight like a fuel oil fire. Cool fire exposed containers with water spray. Firefighter should wear OSHA/NIOSH approved self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARD: Closed containers exposed to high temperatures, such as fire conditions may rupture.
SECTION V - HEALTH HAZARD/TOXICOLOGICAL PROPERTIES
OVEREXPOSURE EFFECTS:
ACUTE EFFECTS:
EYES: Contact with eyes can cause severe irritation, redness, tearing, blurred vision, and/or swelling. May cause eye damage.
SKIN: Contact with skin can cause irritation, (minor itching, burning and/or redness), Dermatitis, defatting may be readily absorbed through the skin.
INHALATION: Inhalation of vapors can cause nasal and respiratory irritation, dizziness, weakness, fatigue, nausea, headache, possible unconsciousness and/or asphyxiation. Aspiration of material into lungs may result in chemical pneumonitis which can be fatal.
INGESTION: Ingestion can cause gastrointestinal irritation, nausea, vomiting, diarrhea.
CHRONIC EFFECTS:
Overexposure to this material has apparently been known to cause the following effects in lab animals: Eye damage, skin damage.
CARCINOGEN: YES _____ NO __X__
TERATOGEN: YES _____ NO __X__
MUTAGEN: YES _____ NO __X__
PRIMARY ROUTES OF EXPOSURE: Skin, inhalation
FIRST AID:
INHALATION: If inhaled, remove victim from exposure to a well-ventilated area. Make them comfortably warm, but not hot. Use oxygen or artificial respiration as required. Consult a physician.
SKIN: For skin contact, wash promptly with soap and excess water.
EYES: For eye contact, flush promptly with excess water for at least fifteen minutes. Consult a physician.
INGESTION: If ingested, do not induce vomiting. Give victim a glass of water. Call a physician immediately.
SECTION V I - REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Open flames, sparks, heat, electrical and static discharge.
INCOMPATIBILITY MATERIALS TO AVOID: Strong acids, alkalis, oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Dioxide, Carbon Monoxide and Carbon.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION VII - SPILL AND DISPOSAL PROCEDURE
SPILLS, LEAK OR RELEASE: Ventilate area. Remove all possible sources of ignition. Avoid prolonged breathing of vapor. Contain spill with inert absorbent.
WASTE DISPOSAL: Dispose of in accordance with local, state, and federal regulations.
SECTION VIII - PROTECTION INFORMATION
RESPIRATORY PROTECTION: If component TLV limits are exceeded, use NIOSH/MSHA approved respirator to remove vapors. Use an air-supplied respirator if necessary.
VENTILATION: Use adequate ventilation in volume and pattern to keep TLV/PEL below recommended levels.
Explosion-proof ventilation may be necessary.
PROTECTIVE GLOVES: To prevent prolonged exposure use rubber gloves; solvents may be absorbed through the skin
EYE PROTECTION: Safety Glasses or goggles with splash guards or side shields.
OTHER PROTECTIVE EQUIPMENT: Wear protective clothing as required to prevent skin contact.
SECTION IX - HANDLING AND STORAGE PRECAUTIONS
STORAGE AND HANDLING: Use with adequate ventilation. Avoid contact with eyes and skin. Avoid breathing vapors. Do not store the product above 100°F/38°C. Do not flame, cut, braze weld or melt empty containers. Keep the product away from heat, open flame, and other sources of ignition. Avoid contact with strong acids, alkalis and oxidizers.
SECTION X - ADDITIONAL INFORMATION
SHIPPING INFORMATION: Please comply with DOT regulations in USA
HMIS RATING: Health 2 4 = Extreme
Fire 1 3 = High
Reactivity 1 2 = Moderate
1 = Slight
0 = Insignificant
Personal Protection - See Section VIII
CALIFORNIA PROPOSITION 65:
Trace amounts of some chemicals known to the State of California to cause cancer, birth defects
or other reproductive harm may be present in this product.
SECTION 313 SUPPLIER NOTIFICATION:
This product contains the following toxic chemicals subject to the reporting requirements of the Emergency
Planning and Community Right-To-Know Act of 1986 and 40 CFR 372:
CHEMICAL NAME CAS % BY WGT
NOT APPLICABLE
THIS INFORMATION MUST BE INCLUDED IN ALL MSDS THAT ARE COPIED AND DISTRIBUTED FOR THIS CHEMICAL
ABBREVIATIONS
IARC = International Agency for Research on Cancer
ACGIH = American Conference of Governmental Industrial Hygienists
NIOSH = National Institute of Occupational Safety and Health
TLV = Threshold Limit Value
PEL = Permissible Emission Level
DOT = Department of Transportation
NTP = National Toxicology Program
N/AV = Not Available
N/AP = Not Applicable
N/E = Not Established
N/D = Not Determined
PREPARED FOR:
J-B Weld Company
P.O. Box 483
1130 Como Street
Sulphur Springs, TX 75482
Tel: (903) 885-7696
Fax: (903) 885-5911
REVIEWED ON May 17, 2004
SUPERSEDES June 23, 2003
REVISION Format
The information in the Material Safety Data Sheet has been compiled from our experience and from data presented in various technical publications. It is the user’s responsibility to determine the suitability of this information for the adoption of the safety precautions as may be necessary. We reserve the right to revise
Material Safety Data Sheets from time to time as new technical information becomes available. The user has the responsibility to contact the Company to make sure that the MSDS is the latest one issued.
MATERIAL SAFETY DATA SHEET
Page 1 Epoxy Steel Resin
J-B Weld Company
P.O. Box 483
1130 Como Street
Sulphur Springs, TX 75482
Tel: (903) 885-7696
Fax: (903) 885-5911
SECTION I - IDENTIFICATION OF PRODUCT
PRODUCT NAME: JB WELD - EPOXY STEEL RESIN
PRODUCT CODE: (48009), 48102, 48153, 48170
SYNONYM/CROSS REFERENCE: Resin Solution
SCHEDULE B NUMBER: 3506.91.0000
SECTION II - HAZARDOUS INGREDIENTS
INGREDIENTS WGT% CAS # TLV/PEL
Calcium Carbonate 40-50% 1317-65-3 ACGIH: TWA 10 mg/m3
OSHA: PEL 15 mppcf
Iron Powder 10-20% 65997-19-5 ACGIH TLV 15 mg/m3
OSHA: PEL 15 mppcf
Epoxy Resin 30-40% 25068-38-6 N/E
Aromatic Hydrocarbons 1-5 % 64742-94-5 N/E
SECTION III - PHYSICAL DATA
APPEARANCE: Dark gray or black smooth paste
SPECIFIC GRAVITY: 1.80
VAPOR PRESSURE (mmHG): N/Av
BOILING POINT: N/E
VAPOR DENSITY: Heavier than air
EVAPORATION RATE (Ethyl Ether = 1): Slower than Ethyl Ether
VOLATILES BY WEIGHT: N/D
SOLUBILITY IN WATER: Not Soluble
VOC: Grams/Liter = Nil
Lbs/Gallon = Nil
SECTION IV - FIRE AND EXPLOSION DATA
FLASH POINT: >200°F/ 93°C Seta Flash Closed cup
LOWER FLAMMABLE LIMIT %: N/E
UPPER FLAMMABLE LIMIT %: N/E
FIRE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES: Fight like a fuel oil fire. Cool fire exposed containers with water spray. Firefighter should wear OSHA/NIOSH approved self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARD: Closed containers exposed to high temperatures, such as fire conditions may rupture.
SECTION V - HEALTH HAZARD/TOXICOLOGICAL PROPERTIES
OVEREXPOSURE EFFECTS:
ACUTE EFFECTS:
EYES: Contact with eyes can cause irritation, redness, tearing, blurred vision, and/or swelling.
SKIN: Contact with skin can cause irritation, (minor itching, burning and/or redness), Dermatitis,
defatting may be readily absorbed through the skin.
INHALATION: Inhalation of vapors can cause nasal and respiratory irritation, dizziness, weakness, fatigue, nausea, headache, possible unconsciousness and/or asphyxiation. Aspiration of material into lungs may result in chemical pneumonitis which can be fatal.
INGESTION: Ingestion can cause gastrointestinal irritation, nausea, vomiting, diarrhea.
CHRONIC EFFECTS:
Overexposure to this material has apparently been known to cause the following effects in lab animals: skin sensitization, respiratory system irritation.
CARCINOGEN: YES _____ NO __X__
TERATOGEN: YES _____ NO __X__
MUTAGEN: YES _____ NO __X__
PRIMARY ROUTES OF EXPOSURE: skin, inhalation, eyes
FIRST AID:
INHALATION: If inhaled, remove victim from exposure to a well-ventilated area. Make them comfortably warm, but not hot. Use oxygen or artificial respiration as required. Consult a physician.
SKIN: For skin contact, wash promptly with soap and excess water.
EYES: For eye contact, flush promptly with excess water for at least fifteen minutes. Consult a physician.
INGESTION: If ingested, do not induce vomiting. Give victim a glass of water. Call a physician immediately.
SECTION V I - REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Open flames & heat. .
INCOMPATIBILITY MATERIALS TO AVOID: Strong acids, alkalis, oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Dioxide, Carbon Monoxide and Carbon.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION VII - SPILL AND DISPOSAL PROCEDURE
SPILLS, LEAK OR RELEASE: Ventilate area. Remove all possible sources of ignition. Avoid prolonged breathing of vapor. Contain spill with inert absorbent.
WASTE DISPOSAL: Dispose of in accordance with local, state, and federal regulations.
SECTION VIII - PROTECTION INFORMATION
RESPIRATORY PROTECTION: If component TLV limits are exceeded, use NIOSH/MSHA approved respirator to remove vapors. Use an air-supplied respirator if necessary. With general ventilation, does not require a respirator.
VENTILATION: Use adequate ventilation in volume and pattern to keep TLV/PEL below recommended levels.
PROTECTIVE GLOVES: To prevent prolonged exposure use rubber gloves; solvents may be absorbed through the skin
EYE PROTECTION: Safety Glasses or goggles with splash guards or side shields.
OTHER PROTECTIVE EQUIPMENT: Wear protective clothing as required to prevent skin contact.
SECTION IX - HANDLING AND STORAGE PRECAUTIONS
STORAGE AND HANDLING: Use with adequate ventilation. Avoid contact with eyes and skin. Avoid breathing vapors. Do not store the product above 100®F/38®C. Do not flame, cut, braze weld or melt empty containers. Keep the product away from heat, open flame, and other sources of ignition. Avoid contact with strong acids, alkalis and oxidizers.
SECTION X - ADDITIONAL INFORMATION
SHIPPING INFORMATION: Please comply with DOT regulations in USA
HMIS RATING: Health 2 4 = Extreme
Fire 1 3 = High
Reactivity 1 2 = Moderate
1 = Slight
0 = Insignificant
Personal Protection - See Section VIII
CALIFORNIA PROPOSITION 65:
Trace amounts of epichlorohydrin, a chemical known to the State of California to cause cancer, are present in this product. However, given the low level and application of this product, typical uses do not constitute a significant risk under the standard.
SECTION 313 SUPPLIER NOTIFICATION:
This product contains the following toxic chemicals subject to the reporting requirements of the Emergency
Planning and Community Right-To-Know Act of 1986 and 40 CFR 372:
CHEMICAL NAME CAS % BY WGT
Not Applicable
THIS INFORMATION MUST BE INCLUDED IN ALL MSDS THAT ARE COPIED AND DISTRIBUTED FOR THIS CHEMICAL
ABBREVIATIONS
IARC = International Agency for Research on Cancer
ACGIH = American Conference of Governmental Industrial Hygienists
NIOSH = National Institute of Occupational Safety and Health
TLV = Threshold Limit Value
PEL = Permissible Emission Level
DOT = Department of Transportation
NTP = National Toxicology Program
N/AV = Not Available
N/AP = Not Applicable
N/E = Not Established
N/D = Not Determined
PREPARED FOR: J-B Weld Company
P.O. Box 483
1130 Como Street
Sulphur Springs, TX 75482
Tel: (903) 885-7696
Fax: (903) 885-5911
REVIEWED ON May 17, 2004
SUPERSEDES March 1, 2003
REVISION Format
The information in the Material Safety Data Sheet has been compiled from our experience and from data presented in various technical publications. It is the user’s responsibility to determine the suitability of this information for the adoption of the safety precautions as may be necessary. We reserve the right to revise
Material Safety Data Sheets from time to time as new technical information becomes available. The user has the responsibility to contact the Company to make sure that the MSDS is the latest one issued.
M A T E R I A L S A F E T Y D A T A S H E E T
2.1 VOC HI SOLIDS ACRYLIC LACQUER - GRAY Page: 1
2/26/2008
PRODUCT NAME: 2.1 VOC HI SOLIDS ACRYLIC LACQUER - GRAY HMIS CODES: H F R P
5 STAR Part Number: FS-5400C-G 2*3 0 G
SECTION I - MANUFACTURER IDENTIFICATION\
MANUFACTURED FOR : ABI/Autobody Brands International
A division of IAMG/International Autobody Marketing Group
ADDRESS : 9419 E. SAN SALVADOR DR. SUITE 104
SCOTTSDALE, AZ 85258
EMERGENCY PHONE : (800)424-9300 (24 hrs.) DATE PRINTED : 2/26/2008
INFORMATION PHONE : 1-87-REFINISH PREPARER NAME: MSDS Coordinator
SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP PERCENT
------------------------------------------------------------------------------------------------------------------------
ACETONE 67-64-1 185 68 F 48.34
ACGIH TLV STEL: 750 ppm
ACGIH TLV TWA: 500 ppm
OSHA VPEL TWA: 750 ppm
OSHA VPEL STEL: 1000 ppm
p-chloro-a,a,a-trifluorotoluene 98-56-6 N/A N/A 5%-15%
ACGIH TLV: 2.5 mg/m3 TWA AS FLUORIDES
OSHA PEL: 2.5 mg/m3 TWA AS FLUORIDES
NIOSH: 2.5 mg/m3 TWA AS FLUORIDES
talc 14807-96-6 N/A 0%-10%
ACGIH TLV: 2 mg/m3 TWA RESPIRABLE DUST
OSHA PEL: 20 mppcf
NITROCELLULOSE 9004-70-0 N/D N/D 5.08
magnesite dust 546-93-0 N/A N/A 0%-10%
OSHA PEL: 15 mg/m3 (TOTAL DUST)
OSHA PEL: 5 mg/m3 (RESPIRABLE DUST)
ACGIH TLV: 10 mg/m3 (TOTAL DUST)
NIOSH: 10 mg/m3 TWA (TOTAL DUST)
NIOSH: 5 mg/m3 TWA (RESPIRABLE DUST)
titanium dioxide 13463-67-7 N/A 0%-10%
OSHA PEL: 10 mg/m3 TWA (TOTAL DUST)
ISOPROPYL ALCOHOL 67-63-0 32 68 F 2.18
OSHA PEL: 400 ppm TWA
ACGIH TLV: 400 ppm TWA
ACGIH TLV: 500 ppm STEL
OSHA PEL: 500 ppm
OSHA STEL: 500 ppm
* di-n-butylphthalate 84-74-2 0.8 302 F 1.94
* XYLENES 1330-20-7 5.10 68 F 1.26
ACGIH TWA 100 ppm
ACGIH STEL 150 ppm
OSHA TWA 100 ppm
OSHA STEL 150 ppm
ETHYL BENZENE 100-41-4 5.1 68 F .26
OSHA PEL: 100 ppm TWA
ACGIH TVL: 100 ppm TWA
PHOSPHORIC ACID 7664-38-2 0.03 68 F .21
OSHA PEL: 1.000 mg/m3 TWA
ACGIH TLV: 1.000 mg/m3 TWA
ACGIH TLV: 3.000 mg/m3 STEL
TOLUENE 108-88-3 22 68 F .16
ACGIH TLV: 150 ppm STEL (SKIN)
ACGIH TLV: 50 ppm TWA (SKIN)
OSHA VPEL: 150 ppm STEL
OSHA VPEL: 100 ppm TWA
SILICA, QUARTZ 14808-60-7 N/A N/A .1493
OSHA PEL: 30 mg/m3 TOTAL DUST
OSHA PEL: 10 mg/m3 RESPIRABLE DUST
ACGIH TLV: 0.1 mg/m3 TWA RESPIRABLE DUST
pseudocumene 95-63-6 1.58 68 F .02
ACGIH TLV: 25 ppm TWA
OSHA PEL: 25 ppm TWA
NIOSH: 25 ppm TWA
NIOSH: 125 mg/m3 TWA
SILICA, CRISTOBALITE 14464-46-1 N/A N/A .001
OSHA PEL: 0.05 mg/m3 RESPIRABLE DUST
ACGIH TLV: 0.05 mg/m3 TWA RESPIRABLE DUST
* Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372.
N/A
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
BOILING RANGE: 133 F - 377.6 F SPECIFIC GRAVITY (H2O=1): 1.06
VAPOR DENSITY: Heavier than air EVAPORATION RATE: Slower than ether
V.O.C. grams/liter: 195.29 V.O.C. lbs./gal.: 1.63
SOLUBILITY IN WATER: Insoluble SOLIDS BY VOLUME: 19.217
APPEARANCE AND ODOR: Opaque liquid with an organic solvent odor.
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: -4.0 F METHOD USED: TAGCC
FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: 0.90 UPPER: 12.8
EXTINGUISHING MEDIA: Foam, Carbon Dioxide, Dry Chemical, Water Fog
SPECIAL FIREFIGHTING PROCEDURES
Full protective equipment, including self contained breathing apparatus, is recommended. Water from fog nozzles may be used to cool closed containers to prevent pressure build up.
UNUSUAL FIRE AND EXPLOSION HAZARDS
When heated above flashpoint, emits flammable vapors which, when mixed with air, can burn or become explosive. Fine mists or sprays may be flammable below the flash point.
SECTION V - REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID
Avoid all sources of ignition
INCOMPATIBILITY (MATERIALS TO AVOID)
Strong oxidizing materials
HAZARDOUS DECOMPOSITION OR BYPRODUCTS
May produce hazardous fumes when heated to decomposition. Fumes may contain Carbon Monoxide and Carbon Dioxide.
HAZARDOUS POLYMERIZATION: Will not occur
SECTION VI - HEALTH HAZARD DATA
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
May cause nose and throat irritation. Repeated and prolonged exposure to organic solvents may lead to permanent brain and nervous system damage. Eye watering, headaches, nausea, dizziness, and loss of coordination are signs that solvent levels are too high.
Individuals with breathing problems must not be exposed to this product. If affected by inhalation, remove to fresh air.
If breathing difficulty persists, consult a physician.
SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
May cause irritation or burning of the eyes. Repeated and prolonged skin contact may cause skin irritation or dermatitis. In case of eye contact, immediately flush eyes with plenty of water for at least 15 minutes; call a physician. In case of skin contact, wash with soap and water. If irritation occurs, contact a physician.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Gastrointestinal distress. In the unlikely event of ingestion, call a physician immediately and have the names of all ingredients available.
HEALTH HAZARDS (ACUTE AND CHRONIC)
ACUTE- Dizziness, irritation of the respiratory tract, weakness, nausea, or possible narcosis or even asphyxiation. May be accompanied by coughing or labored breathing.
CHRONIC- Reports have linked organic solvents with brain and nervous system damage. Misuse of this product by deliberately concentrating and inhaling the contents may be harmful or fatal.
CARCINOGENICITY: NTP CARCINOGEN: Yes IARC MONOGRAPHS: Yes
PROPOSITION 65 STATEMENT: WARNING! This product contains a chemical or chemicals known to the state of California to cause cancer and/or birth defects or other reproductive harm.
OSHA REGULATED: Yes
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
Do not use this product if you have chronic lung or breathing problems.
EMERGENCY AND FIRST AID PROCEDURES
If ingestion, or any type of overexposure or symptoms of overexposure occur during the use of this product, contact a poison control center, emergency room or physician immediately; have material safety data sheet available.
SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Remove all sources of ignition (sparks, flames, and hot surfaces). Avoid breathing vapors. Ventilate area. Remove with inert absorbent and non-sparking tools.
WASTE DISPOSAL METHOD
Dispose in accordance with state , federal and local regulations. Do not incinerate closed containers.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Keep containers tightly closed in a cool, dry, well ventilated area away from all possible ignition sources. Store large
quanaties of material in buildings designed for the storage of flammable liquids.
OTHER PRECAUTIONS
Employees should be trained in safety measures that should be taken when using this product.
SECTION VIII - CONTROL MEASURES
RESPIRATORY PROTECTION
Avoid breathing vapors or spray mist. Wear a properly fitted respirator approved by NIOSH/MSHA (TC-23c) for use with paints during application and until all vapors are exhausted. In confined areas, or where continuous spray operations are typical, or proper respirator fit is not possible, wear a positive-pressure supplied air respirator (TC-19c). In all cases follow respirator manufactures directions for respirator use. Do not allow anyone without protection into the painting area.
VENTILATION
Provide sufficient ventilation to keep contaminates below applicable OSHA requirements.
PROTECTIVE GLOVES
Neoprene gloves impervious to organic solvents are recommended.
EYE PROTECTION
Use safety eyewear designed to protect against liquid splash.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT
Impervious coveralls are recommended.
WORK/HYGIENIC PRACTICES
Eye wash and safety showers in the work place are recommended. Wash hands before eating and smoking.
SECTION IX - DISCLAIMER
The information contained in this material safety data sheet is information from our suppliers and other sources. It is believed to be reliable. This data is not to be taken as a warranty or representation for which this company assumes legal responsibility.
DIMENSION® PRO NR Acrylic Enamel D6/W
Continued IV-93
Material Safety Data Sheet
2006
Section 1 -- Product and Company Identification
PRODUCT NUMBER HMIS CODES
Health 2*
D6/W Flammability 3
Reactivity 0
PRODUCT NAME
DIMENSION® PRO NR Acrylic Enamel, All Colors
MANUFACTURER'S NAME EMERGENCY TELEPHONE NO.
WESTERN AUTOMOTIVE FINISHES (216) 566-2917
101 Prospect Avenue N.W.
Cleveland, OH 44115
DATE OF PREPARATION INFORMATION TELEPHONE NO.
14-NOV-06 (216) 566-2902
Section 2 -- Composition/Information on Ingredients
% by WT CAS No. INGREDIENT UNITS VAPOR PRESSURE
1-5 64742-88-7 Mineral Spirits
ACGIH TLV 100 ppm 2 mm
OSHA PEL 100 ppm
0-2 108-88-3 Toluene
ACGIH TLV 50 ppm (Skin) 22 mm
OSHA PEL 100 ppm (Skin)
OSHA PEL 150 ppm (Skin) STEL
4-5 100-41-4 Ethylbenzene
ACGIH TLV 100 ppm 7.1 mm
ACGIH TLV 125 ppm STEL
OSHA PEL 100 ppm
OSHA PEL 125 ppm STEL
20-30 1330-20-7 Xylene
ACGIH TLV 100 ppm 5.9 mm
ACGIH TLV 150 ppm STEL
OSHA PEL 100 ppm
OSHA PEL 150 ppm STEL
1-2 111-76-2 2-Butoxyethanol
ACGIH TLV 20 ppm 0.88 mm
OSHA PEL 25 ppm
5-10 67-64-1 Acetone
ACGIH TLV 500 ppm 180 mm
ACGIH TLV 750 ppm STEL
OSHA PEL 1000 ppm
0.5-1 107-87-9 Methyl n-Propyl Ketone
ACGIH TLV 200 ppm 27.8 mm
ACGIH TLV 250 ppm STEL
OSHA PEL 200 ppm
OSHA PEL 250 ppm STEL
2-10 123-86-4 n-Butyl Acetate
ACGIH TLV 150 ppm 10 mm
ACGIH TLV 200 ppm STEL
OSHA PEL 150 ppm
OSHA PEL 200 ppm STEL
0.5-2 112-07-2 2-Butoxyethyl Acetate
ACGIH TLV Not Available 1 mm
OSHA PEL Not Available
0-5 Proprietary Coated Mica
ACGIH TLV 3 mg/m3 as Dust
OSHA PEL 3 mg/m3 as Dust
0-26 13463-67-7 Titanium Dioxide
ACGIH TLV 10 mg/m3 as Dust
OSHA PEL 10 mg/m3 Total Dust
OSHA PEL 5 mg/m3 Respirable Fraction
0-1 1333-86-4 Carbon Black
ACGIH TLV 3.5 mg/m3
OSHA PEL 3.5 mg/m3
0-10 8007-18-9 Nickel Antimony Titanate
ACGIH TLV 0.5 mg/m3
OSHA PEL 0.5 mg/m3
-------------------------------------
0.9 maximum Antimony (as Sb)
CERTAIN COLORS CONTAIN LEAD AND CHROMIUM (see PRODUCT LABEL)
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- about this project uk open government network
- investigative research publi records and publicly
- creative services inc specializing in corporate
- law websites
- characteristics united states courts
- cosrocs it is rocket science
- public records notes ibiblio
- human resources employment law
- project georgia judicial gateway georgia judicial