Instructions For Completing Experiment Document Worksheets
[pic]
Hardware Requirements Document (HRD)
for
Visuomotor and Orientation Investigation on
Long-duration Astronauts (VOILA)
CCB CONTROL
|PROJECT DOCUMENT APPROVAL SHEET |
|document number |DATE |NO. OF | |
|ls-XXXXX |TBD |PAGES | TBD |
|TITLE: |
| |
| |
|Hardware Requirements Document (HRD) |
|for |
|VOILA |
|aPPROVED: |EB/Elizabeth Bauer |
| |Technical Manager |
|approved: |NT3/V. Watkins |
| |GFE Assurance Branch |
|approved: |EA2/L. Bromley |
| |Project Management Office |
|approved: |EB/James LeBlanc |
| |Division Chief |
|approved: |SM3/D. Baumann |
| |HRF Experiment Support Manager |
|DATE |PREPARED BY |CHANGE APPROVALS |CHANGE |
| | | |NUMBER |
| | | | |
jsc form 604 (rev jul 81) nasa-jsc
|Report Number LS-71099 |Date 11/20/01 |
| |
|Hardware Requirements Document (HRD) |
| |
|for |
|VOILA |
|Prepared by: | | |
| |Larry Walters |Date |
| |System Engineer | |
|Approved: | | |
| |Ara Kulhanjian |Date |
| |Project Manager | |
|Approved: | | |
| |Don Kilbourn |Date |
| |Manager, S&PA Department | |
|Approved: |Jerry McDonald | |
| |HRF Hardware Development Section Manager |Date |
| |
|Prepared By: |
|Lockheed Martin Engineering and Sciences |
|Houston, Texas |
|for |
|National Aeronautics and Space Administration |
|Johnson Space Center |
|REVISION/CHANGE APPROVALS |
| |Change | |Approved by: |
|Date |Number |Prepared by |Unit Manager |SR&QA Manager |Projects Manager |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
Lockheed Martin Space Operations (March 1999)
|document number |DOCUMENT CHANGE/ |page 1 OF 1 |
|ls-XXXXX |REVISION LOG | |
|CHANGE/ |DATE |DESCRIPTION OF CHANGE |PAGES |
|REVISION | | |AFFECTED |
|Basic |TBD |Baseline Issue – Reference CCBD: | All |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
|Altered pages must be typed and distributed for insertion. |
jsc form 278 (rev APR 81) nasa-jsc
Preface
This Hardware Requirements Document (HRD) defines the minimum set of requirements for the VOILA hardware to be placed on the International Space Station (ISS) and mounted within the HRF Rack. This document is under the control of the HRF Configuration Control Board (CCB).
___________________________________
HRF CCB Chair DATE
CONTENTS
Section Page
1.0 SCOPE 1-1
1.1 GUIDELINES FOR COMPLETION OF THE HARDWARE REQUIREMENTS DOCUMENT TEMPLATE 1-Error! Bookmark not defined.
2.0 APPLICABLE DOCUMENTS 2-1
2.1 DOCUMENTS 2-1
2.2 ORDER OF PRECEDENCE 2-4
3.0 SYSTEM REQUIREMENTS 3-1
3.1 ITEM DEFINITION 3-1
3.2 CHARACTERISTICS 3-10
3.2.1 Performance Characteristics 3-10
3.2.1.1 Functional Performance Characteristics 3-10
3.2.2 Physical Characteristics 3-13
3.2.2.1 Mass and Center of Gravity Properties 3-13
3.2.2.1.1 HRF Rack Mounted Standard Interface Rack (SIR) Drawer Center-of-Gravity Constraints 3-14
3.2.2.2 Envelope 3-Error! Bookmark not defined.
3.2.2.2.1 Stowed Envelope 3-Error! Bookmark not defined.
3.2.2.2.2 Deployed Envelope 3-15
3.2.2.2.2.1 On-Orbit Payload Protrusions 3-15
3.2.2.2.2.1.1 On-Orbit Permanent Protrusions 3-16
3.2.2.2.2.1.2 On-Orbit Semi-Permanent Protrusions 3-17
3.2.2.2.2.1.3 On-Orbit Temporary Protrusions 3-18
3.2.2.2.2.1.4 On-Orbit Momentary Protrusions 3-19
3.2.2.2.2.2 Deployed Envelope Dimensions 3-19
3.2.3 Reliability, Quality and Non-Conformance Reporting 3-19
3.2.3.1 Failure Propagation 3-20
3.2.3.2 Useful Life 3-20
3.2.3.2.1 Operational Life (Cycles) 3-21
3.2.3.2.2 Shelf Life 3-21
3.2.3.2.3 Limited Life 3-21
3.2.4 Maintainability 3-21
3.2.4.1 Logistics and Maintenance 3-22
3.2.4.1.1 Payload In-Flight Maintenance 3-22
3.2.4.1.2 Maintenance 3-22
3.2.5 Environmental Conditions 3-22
3.2.5.1 On-Orbit Environmental Conditions 3-22
CONTENTS (Cont’d)
Section Page
3.2.5.1.1 On-Orbit Internal Environments 3-22
3.2.5.1.1.1 Pressure 3-22
3.2.5.1.1.2 Temperature 3-22
3.2.5.1.1.3 Humidity 3-23
3.2.5.1.2 Use of Cabin Atmosphere 3-23
3.2.5.1.2.1 Active Air Exchange 3-23
3.2.5.1.2.2 Oxygen Consumption 3-23
3.2.5.1.2.3 Chemical Releases 3-23
3.2.5.1.2.4 Cabin Air Heat Leak 3-23
3.2.5.1.3 Ionizing Radiation Requirements 3-23
3.2.5.1.3.1 Instrument Contained or Generated Ionizing Radiation 3-23
3.2.5.1.3.2 Ionizing Radiation Dose 3-23
3.2.5.1.3.3 Single Event Effect (SEE) Ionizing Radiation 3-23
3.2.5.1.4 Additional Environmental Conditions 3-24
3.2.5.1.5 Pressure Rate of Change 3-27
3.2.5.1.6 Microgravity 3-28
3.2.5.2 Acoustic Emission Limits 3-29
3.2.5.2.1 Continuous Noise Limits 3-29
3.2.5.2.2 Intermittent Noise Limits 3-30
3.2.5.3 Lighting Design 3-31
3.2.5.4 Front Panel Surface Temperature 3-32
3.2.6 Transportability 3-32
3.2.6.1 Launch and Landing 3-32
3.2.7 Operational Interface Requirements 3-33
3.2.7.1 Mechanical Interface Requirements 3-33
3.2.7.1.1 Connector Physical Mate 3-33
3.2.7.1.2 HRF Rack to SIR Drawer Structural Interface Requirements 3-33
3.2.7.1.2.1 Dimensional Tolerances 3-34
3.2.7.1.2.2 SIR Drawer Structural/ Mechanical Interfaces 3-35
3.2.7.1.2.3 Reserved 3-35
3.2.7.1.2.4 HRF Rack Seat Track Interfaces 3-35
3.2.7.2 Electrical Power Interface Requirements 3-35
3.2.7.2.1 HRF Rack Power Output Connectors 3-35
3.2.7.2.1.1 SIR Drawer Power Connectors 3-35
3.2.7.2.1.2 Rack Connector Panel J1 Power Connector 3-36
3.2.7.2.2 Voltage Characteristics 3-36
3.2.7.2.2.1 Steady-State Operating Voltage Envelope 3-36
3.2.7.2.2.2 Transient Operating Voltage Envelope 3-36
CONTENTS (Cont’d)
Section Page
3.2.7.2.2.3 Ripple Voltage/Noise Characteristics 3-36
3.2.7.2.3 Maximum Current Limit 3-39
3.2.7.2.4 Reverse Current 3-40
3.2.7.2.5 Reverse Energy 3-40
3.2.7.2.6 Capacitive Loads 3-40
3.2.7.2.7 Electromagnetic Compatibility (EMC) 3-40
3.2.7.2.7.1 Electrical Grounding 3-40
3.2.7.2.7.2 Electrical Bonding 3-40
3.2.7.2.7.3 Electromagnetic Interference 3-41
3.2.7.2.8 Electrostatic Discharge 3-42
3.2.7.2.9 Corona 3-42
3.2.7.2.10 Cable/Wire Design and Control Requirements 3-42
3.2.7.2.10.1 Wire Derating 3-42
3.2.7.2.10.2 Exclusive Power Feeds 3-42
3.2.7.2.11 Loss of Power 3-43
3.2.7.2.12 Alternating Current Magnetic Fields 3-43
3.2.7.2.13 Direct Current Magnetic Fields 3-43
3.2.7.3 Command and Data Handling Interface Requirements 3-43
3.2.7.3.1 HRF Rack Data Connectors 3-43
3.2.7.3.1.1 SIR Drawer Data Connectors 3-43
3.2.7.3.1.2 HRF Rack Connector Panel J2 Data Connector 3-46
3.2.7.3.2 HRF Ethernet Interfaces 3-46
3.2.7.3.3 HRF TIA/EIA-422 Interfaces 3-46
3.2.7.3.4 HRF Bi-Directional Discretes Interfaces 3-46
3.2.7.3.5 HRF Analog Interfaces 3-46
3.2.7.3.6 HRF Software Requirements. 3-46
3.2.7.3.7 Reserved 3-59
3.2.7.3.8 Reserved 3-59
3.2.7.3.9 Reserved 3-59
3.2.7.3.10 Medium Rate Data Link 3-59
3.2.7.3.10.1 Data Transmissions 3-Error! Bookmark not defined.
3.2.7.3.10.2 Consultative Committee for Space Data Systems (CCSDS) Data 3-Error! Bookmark not defined.
3.2.7.3.10.2.1 CCSDS Data Packets 3-Error! Bookmark not defined.
3.2.7.3.10.2.1.1 CCSDS Primary Header 3-Error! Bookmark not defined.
3.2.7.3.10.2.1.2 CCSDS Secondary Header 3-Error! Bookmark not defined.
3.2.7.3.10.2.2 CCSDS Data Field 3-Error! Bookmark not defined.
3.2.7.3.10.2.3 CCSDS Application Process Identification Field 3-Error! Bookmark not defined.
CONTENTS (Cont’d)
Section Page
3.2.7.4 Payload National Television Standards Committee (NTSC) Video Interface Requirements 3-59
3.2.7.4.1 HRF Rack Video Connectors 3-Error! Bookmark not defined.
3.2.7.4.1.1 SIR Drawer Video Interface 3-Error! Bookmark not defined.
3.2.7.4.1.2 Rack Connector Panel Interface 3-Error! Bookmark not defined.
3.2.7.4.2 HRF Rack Video Interface Characteristics 3-Error! Bookmark not defined.
3.2.7.5 Thermal Control Interface Requirements 3-59
3.2.7.5.1 HRF Rack Provided Internal Thermal Control System (ITCS) Moderate Temperature Loop (MTL) Interface 3-59
3.2.7.5.1.1 HRF Rack MTL Interface Connectors 3-Error! Bookmark not defined.
3.2.7.5.1.2 ITCS Fluid Use and Charging 3-Error! Bookmark not defined.
3.2.7.5.1.3 Reserved 3-Error! Bookmark not defined.
3.2.7.5.1.4 Coolant Maximum Design Pressure 3-Error! Bookmark not defined.
3.2.7.5.1.5 Payload Coolant Quantity 3-Error! Bookmark not defined.
3.2.7.5.1.6 Fail Safe Design 3-Error! Bookmark not defined.
3.2.7.5.1.7 Leakage 3-Error! Bookmark not defined.
3.2.7.5.1.8 Quick-Disconnect Air Inclusion 3-Error! Bookmark not defined.
3.2.7.5.2 HRF Rack Heat Exchanger to SIR Drawer Interface 3-59
3.2.7.5.2.1 Reserved 3-59
3.2.7.5.2.2 HRF Rack Mounted SIR Drawer Cooling Fans 3-60
3.2.7.6 Vacuum System Requirements 3-61
3.2.7.6.1 HRF Rack Vacuum Interface Connectors 3-Error! Bookmark not defined.
3.2.7.6.2 VES Requirements 3-Error! Bookmark not defined.
3.2.7.6.2.1 Input Pressure Limit 3-Error! Bookmark not defined.
3.2.7.6.2.2 Input Temperature Limit 3-Error! Bookmark not defined.
3.2.7.6.2.3 Input Dewpoint Limit 3-Error! Bookmark not defined.
3.2.7.6.2.4 Acceptable Exhaust Gases 3-Error! Bookmark not defined.
3.2.7.6.2.4.1 Acceptable Gases List 3-Error! Bookmark not defined.
3.2.7.6.2.5 External Contamination Control 3-Error! Bookmark not defined.
3.2.7.6.2.6 Incompatible Gases 3-Error! Bookmark not defined.
3.2.7.6.3 Vacuum Resource System Requirements 3-Error! Bookmark not defined.
3.2.7.6.3.1 Input Pressure Limit 3-Error! Bookmark not defined.
3.2.7.6.3.2 VRS Through-Put Limit 3-Error! Bookmark not defined.
3.2.7.6.3.3 Acceptable Gases 3-Error! Bookmark not defined.
3.2.7.7 Pressurized Gas Interface Requirements 3-61
3.2.7.7.1 Nitrogen Interface Requirements 3-Error! Bookmark not defined.
3.2.7.7.1.1 HRF Rack Nitrogen Interface Connectors 3-Error! Bookmark not defined.
3.2.7.7.1.2 Nitrogen Interface Control 3-Error! Bookmark not defined.
CONTENTS (Cont’d)
Section Page
3.2.7.7.1.3 Nitrogen Interface Maximum Design Pressure (MDP) 3-Error! Bookmark not defined.
3.2.7.7.1.4 Nitrogen Interface Temperature 3-Error! Bookmark not defined.
3.2.7.7.1.5 Nitrogen Leakage 3-Error! Bookmark not defined.
3.2.7.7.2 Pressurized Gas Systems 3-Error! Bookmark not defined.
3.2.7.7.3 Manual Valves 3-Error! Bookmark not defined.
3.2.7.8 Payload Support Services Interfaces Requirements 3-61
3.2.7.8.1 Potable Water 3-Error! Bookmark not defined.
3.2.7.8.1.1 ISS Potable Water Interface Connection 3-Error! Bookmark not defined.
3.2.7.8.1.2 Potable Water Interface Pressure 3-Error! Bookmark not defined.
3.2.7.8.1.3 Potable Water Use 3-Error! Bookmark not defined.
3.2.7.8.2 Fluid System Servicer 3-Error! Bookmark not defined.
3.2.7.9 Fire Protection Interface Requirements 3-61
3.2.7.9.1 Fire Prevention 3-62
3.2.7.9.2 Payload Monitoring and Detection Requirements 3-62
3.2.7.9.2.1 Parameter Monitoring 3-62
3.2.7.9.2.1.1 Parameter Monitoring Use 3-Error! Bookmark not defined.
3.2.7.9.2.1.2 Parameter Monitoring Response in Subrack 3-Error! Bookmark not defined.
3.2.7.9.3 Fire Suppression 3-62
3.2.7.9.3.1 Portable Fire Extinguisher 3-62
3.2.7.9.3.2 Fire Suppression Access Port Accessibility 3-62
3.2.7.9.3.3 Fire Suppressant Distribution 3-64
3.2.7.9.4 Labeling 3-64
3.2.7.10 Other Interface Requirements 3-64
3.3 DESIGN AND CONSTRUCTION 3-66
3.3.1 Materials, Processes, and Parts 3-66
3.3.1.1 Materials and Processes 3-66
3.3.1.1.1 Materials and Parts Use and Selection 3-66
3.3.1.1.1.1 Russian Materials Usage Agreement 3-66
3.3.1.1.2 Commercial Parts 3-66
3.3.1.1.3 Fluids 3-66
3.3.1.1.4 Cleanliness 3-66
3.3.1.1.5 Fungus Resistant Material 3-66
3.3.1.2 Sharp Edges and Corner Protection 3-66
3.3.1.3 Holes 3-67
3.3.1.4 Latches 3-67
3.3.1.5 Screws and Bolts 3-67
3.3.1.6 Securing Pins 3-67
3.3.1.7 Levers, Cranks, Hooks and Controls 3-67
CONTENTS (Cont’d)
Section Page
3.3.1.8 Burrs 3-67
3.3.1.9 Locking Wires 3-67
3.3.2 Nameplates and Product Marking 3-67
3.3.2.1 Equipment Identification 3-67
3.3.3 Workmanship 3-68
3.3.4 Interchangeability 3-68
3.3.5 Safety Requirements 3-68
3.3.5.1 Electrical Safety 3-68
3.3.5.1.1 Safety-Critical Circuits Redundancy 3-68
3.3.5.1.2 EMI Susceptibility for Safety-Critical Circuits 3-68
3.3.5.1.3 Mating/Demating of Powered Connectors 3-68
3.3.5.1.4 Power Switches/Controls 3-68
3.3.5.1.5 Ground Fault Circuit Interrupters/Portable Equipment DC Sourcing Voltage 3-69
3.3.5.1.6 Portable Equipment/Power Cords 3-69
3.3.6 Human Engineering 3-69
3.3.6.1 Closures or Covers Design Requirements 3-69
3.3.6.2 Interior Color 3-69
3.3.6.2.1 Rack Mounted Equipment 3-69
3.3.6.2.2 Stowed/Deployable Equipment 3-69
3.3.6.2.3 Colors for Soft Goods 3-70
3.3.6.3 Full Size Range Accommodation 3-70
3.3.6.4 Operation and Control of Payload Equipment 3-70
3.3.6.5 Maintenance Operations 3-73
3.3.6.6 Adequate Clearance 3-73
3.3.6.7 Accessibility 3-73
3.3.6.8 One-Handed Operation 3-74
3.3.6.9 Continuous/Incidental Contact - High Temperature 3-74
3.3.6.10 Continuous/Incidental Contact - Low Temperature 3-74
3.3.6.11 Equipment Mounting 3-74
3.3.6.12 Drawers and Hinged Panels 3-74
3.3.6.13 Alignment 3-74
3.3.6.14 Slide-Out Stops 3-75
3.3.6.15 Push-Pull Force 3-75
3.3.6.16 Covers 3-75
3.3.6.17 Self-Supporting Covers 3-75
3.3.6.18 Accessibility 3-75
3.3.6.19 Ease of Disconnect 3-75
CONTENTS (Cont’d)
Section Page
3.3.6.20 Indication of Pressure/Flow 3-76
3.3.6.21 Self Locking 3-76
3.3.6.22 Connector Arrangement 3-76
3.3.6.23 Arc Containment 3-76
3.3.6.24 Connector Protection 3-76
3.3.6.25 Connector Shape 3-76
3.3.6.26 Fluid and Gas Line Connectors 3-76
3.3.6.27 Alignment Marks or Guide Pins 3-76
3.3.6.28 Coding 3-77
3.3.6.29 Pin Identification 3-77
3.3.6.30 Orientation 3-77
3.3.6.31 Hose/Cable Restraints 3-77
3.3.6.32 Non-Threaded Fasteners Status Indication 3-77
3.3.6.33 Mounting Bolt/Fastener Spacing 3-78
3.3.6.34 Multiple Fasteners 3-78
3.3.6.35 Captive Fasteners 3-78
3.3.6.36 Quick Release Fasteners 3-78
3.3.6.37 Threaded Fasteners 3-78
3.3.6.38 Over Center Latches 3-78
3.3.6.39 Winghead Fasteners 3-80
3.3.6.40 Fastener Head Type 3-80
3.3.6.41 One-Handed Actuation 3-80
3.3.6.42 DELETED 3-80
3.3.6.43 Access Holes 3-80
3.3.6.44 Controls Spacing Design Requirements 3-80
3.3.6.45 Accidental Activation 3-80
3.3.6.45.1 Protective Methods 3-82
3.3.6.45.2 Noninterference 3-82
3.3.6.45.3 Dead-Man Controls 3-82
3.3.6.45.4 Barrier Guards 3-83
3.3.6.45.5 Recessed Switch Protection 3-83
3.3.6.46 Position Indication 3-83
3.3.6.47 Hidden Controls 3-83
3.3.6.48 Hand Controllers 3-84
3.3.6.49 Valve Controls 3-84
3.3.6.50 Toggle Switches 3-84
3.3.6.51 Restraints and Mobility Aids 3-86
3.3.6.51.1 Stowage Drawer Contents Restraints 3-86
CONTENTS (Cont’d)
Section Page
3.3.6.51.2 Stowage and Equipment Drawers/Trays 3-86
3.3.6.51.3 Captive Parts 3-86
3.3.6.51.4 Handle and Grasp Area Design Requirements 3-86
3.3.6.51.4.1 Handles and Restraints 3-86
3.3.6.51.4.2 Handle Location/Front Access 3-87
3.3.6.51.4.3 Handle Dimensions 3-87
3.3.6.51.4.4 Non-Fixed Handles Design Requirements 3-87
3.3.6.52 Electrical Hazards 3-87
3.3.6.52.1 Mismatched 3-90
3.3.6.52.2 Overload Protection 3-90
3.3.6.52.2.1 Device Accessibility 3-90
3.3.6.52.2.2 Extractor -Type Fuse Holder 3-90
3.3.6.52.2.3 Overload Protection Location 3-90
3.3.6.52.2.4 Overload Protection Identification 3-91
3.3.6.52.2.5 Automatic Restart Protection 3-91
3.3.6.53 Audio Devices (Displays) 3-91
3.3.6.54 Egress 3-91
3.3.7 System Security 3-91
3.3.8 Design Requirements 3-91
3.3.8.1 Structural Design Requirements 3-91
3.3.8.1.1 On-orbit Loads 3-91
3.3.8.1.2 Safety Critical Structures Requirements 3-92
3.3.8.1.3 First Modal Frequency 3-92
3.3.8.1.4 Launch and Landing Loads 3-92
3.3.8.2 Electrical Power Consuming Equipment Design 3-94
3.3.8.2.1 Batteries 3-94
3.4 ACCEPTANCE AND QUALIFICATION REQUIREMENTS 3-94
3.4.1 Thermal Environment Compatibility 3-94
3.4.2 Vibration and Sine Sweep 3-94
3.4.3 Functional Acceptance 3-94
3.4.4 Electrical, Electronic and Electromechanical Parts Control, Selection and Burn-In 3-94
3.4.5 Flammability 3-95
3.4.6 Offgassing 3-95
3.4.7 Shock 3-95
3.4.8 Bench Handling 3-95
3.4.9 Payload Mass 3-95
3.4.10 Electromagnetic Compatibility 3-95
CONTENTS (Cont’d)
Section Page
3.4.11 Acoustic Noise 3-95
3.4.12 Safety Critical Structure Verification 3-96
3.4.12.1 Safety Critical Structure Dimensional Check 3-96
3.4.12.2 Safety Critical Structure Material Certification 3-96
3.4.13 Software Acceptance 3-96
3.4.14 Pre-Delivery Acceptance 3-96
3.4.15 Pre-Installation Acceptance 3-96
3.5 HRP PROGRAM REQUIREMENTS 3-96
3.5.1 Safety 3-96
3.5.2 Documentation Requirements 3-96
3.5.2.1 Acceptance Data Package (ADP) 3-96
3.5.2.1.1 ADP Statement in SOW 3-98
3.5.2.2 Additional Required Documentation 3-98
4.0 VERIFICATION PROVISIONS 4-1
4.1 GENERAL 4-1
4.2 FUNCTIONAL PERFORMANCE ACCEPTANCE TESTING 4-2
4.3 ACCEPTANCE AND QUALIFICATION VERIFICATION METHODS 4-2
4.3.1 Thermal Cycle Tests 4-2
4.3.1.1 Qualification Thermal Cycle Test 4-3
4.3.1.2 Acceptance Thermal Cycle Test 4-3
4.3.2 Vibration Tests 4-6
4.3.2.1 Sinusoidal Resonance Survey 4-6
4.3.2.2 Random Vibration Test 4-6
4.3.2.2.1 Qualification Vibration Analysis 4-7
4.3.2.2.2 Qualification for Acceptance Vibration Test 4-7
4.3.2.2.3 Acceptance Vibration Test 4-7
4.3.3 Functional Testing 4-8
4.3.4 Electrical, Electronic, and Electromechanical Parts Control, Selection, and Burn-In 4-8
4.3.5 Flammability 4-9
4.3.6 Offgassing 4-9
4.3.7 Shock Test 4-9
4.3.8 Bench Handling 4-10
4.3.9 Payload Mass 4-10
4.3.10 Electromagnetic Compatibility 4-10
4.3.11 Acoustic Noise 4-10
CONTENTS (Cont’d)
Section Page
4.3.12 Safety Critical Structure Verification 4-10
4.3.12.1 Safety Critical Structure Dimensional Check 4-10
4.3.12.2 Safety Critical Structure Material Certification 4-10
4.3.13 Software Acceptance 4-10
4.3.14 Pre-Delivery Acceptance 4-10
4.3.15 Pre-Installation Acceptance (PIA) 4-11
5.0 PREPARATION FOR SHIPMENT 5-1
5.1 GENERAL 5-1
5.2 PACKING, HANDLING AND TRANSPORTATION 5-1
5.3 PRESERVATION AND PACKING 5-1
5.4 MARKING FOR SHIPMENT 5-1
5.5 NASA CRITICAL SPACE ITEM LABEL 5-2
6.0 NOTES 6-1
6.1 DEFINITIONS 6-1
APPENDIX A RESERVED A-1
APPENDIX B ISS PRESSURIZED PAYLOAD INTERFACE REQUIREMENTS DOCUMENT VERIFICATION MATRIX B-1
APPENDIX C FUNCTIONAL PERFORMANCE VERIFICATION MATRIX C-1
APPENDIX D ACCEPTANCE AND QUALIFICATION TEST APPLICABILITY MATRICES D-1
APPENDIX E JHB 8080.5 DESIGN GUIDANCE MATRIX E-1
LIST OF TABLES
Table Page
3.1-1 EQUIPMENT ITEMS 3-1
3.1-2 [HARDWARE DESIGNATION] SOFTWARE 3-3
3.2.2.1-1 STOWAGE UNIT WEIGHT ALLOWANCE 3-Error! Bookmark not defined.
3.2.2.1.1-1 HRF SIR DRAWER CENTER-OF-GRAVITY CONSTRAINTS 3-14
3.2.2.2.1-1 STOWAGE UNIT VOLUME ALLOWANCE 3-Error! Bookmark not defined.
3.2.5.1.4-1 ENVIRONMENTAL CONDITIONS ON ISS 3-25
3.2.5.1.5-1 ISS PRESSURE RATE OF CHANGE 3-27
3.2.5.1.5-2 MPLM PRESSURE RATE OF CHANGE 3-27
3.2.5.1.5-3 ORBITER MIDDECK PRESSURE RATE OF CHANGE 3-27
3.2.5.2.1-1 CONTINUOUS NOISE LIMITS 3-30
3.2.5.2.2-1 INTERMITTENT NOISE LIMITS 3-31
3.2.5.3-1 SURFACE INTERIOR COLORS AND PAINTS 3-32
3.2.5.3-2 PAYLOAD REQUIRED ILLUMINATION LEVELS 3-Error! Bookmark not defined.
3.2.7.1.2.1-1 DIMENSIONAL TOLERANCES 3-34
3.2.7.2.1.1-1 SIR DRAWER POWER CONNECTOR PIN ASSIGNMENTS 3-36
3.2.7.2.1.2-1 RACK CONNECTOR PANEL J1 POWER CONNECTOR PIN ASSIGNMENTS 3-Error! Bookmark not defined.
3.2.7.2.7.3-1 RS03PL 3-41
3.2.7.3.1.1-1 HRF SIR DRAWER DATA CONNECTOR PIN ASSIGNMENTS 3-44
3.2.7.3.1.2-1 HRF RACK CONNECTOR PANEL J2 DATA CONNECTOR PIN ASSIGNMENTS 3-Error! Bookmark not defined.
3.3.5.1.5-1 LET-GO CURRENT PROFILE THRESHOLD VERSUS FREQUENCY 3-Error! Bookmark not defined.
3.3.6.52-1 LET-GO CURRENT PROFILE, THRESHOLD VERSUS FREQUENCY 3-89
3.3.8.1.1-1 CREW-INDUCED LOADS 3-92
3.3.8.1.4-1 RANDOM VIBRATION CRITERIA FOR HRF RACK POST MOUNTED EQUIPMENT WEIGHING 100 POUNDS OR LESS IN THE MPLM 3-93
3.3.8.1.4-2 RANDOM VIBRATION CRITERIA FOR HRF RACK POST MOUNTED EQUIPMENT WEIGHING MORE THAN 100 POUNDS IN THE MPLM 3-93
3.3.8.1.4-3 HRF RACK MOUNTED EQUIPMENT LOAD FACTORS (EQUIPMENT FREQUENCY 35 HZ) 3-93
4.3.2.2.2-1 QUALIFICATION FOR ACCEPTANCE VIBRATION TEST LEVELS 4-7
4.3.2.2.3-1 ACCEPTANCE VIBRATION TEST LEVELS 4-8
LIST OF TABLES (Cont’d)
Table Page
D-1 ACCEPTANCE AND QUALIFICATION TEST APPLICABILITY MATRIX D-1
D-2 NON-CRITICAL HARDWARE QUALIFICATION TEST REQUIREMENTS D-3
D-3 NON-CRITICAL HARDWARE ACCEPTANCE TEST REQUIREMENTS D-4
LIST OF FIGURES
Figure Page
3.2.2.2.2.1.2-1 SIR and ISIS Drawer Handles Protrusion Envelope 3-17
3.2.2.2.2.1.2-2 On-Orbit Semi-Permanent Protrusions Envelope 3-18
3.2.2.2.2.1.3-1 On-Orbit Temporary Protrusions Envelope 3-19
3.2.5.1.1.3-1 ISS Temperature/Humidity Envelope 3-Error! Bookmark not defined.
3.2.5.1.4-1 Operating Limits of the ISS Atmospheric Total Pressure, Nitrogen and Oxygen Partial Pressures 3-26
3.2.5.1.5-1 Manual Fire Suppression System Performance Characteristics 3-28
3.2.7.1.2-1 HRF Rack SIR Drawer Accommodations 3-34
3.2.7.2.1.1-1 SIR Drawer Power Connector Part Number M83733/2RA018 3-35
3.2.7.2.1.2-1 Rack Connector Panel J1 Power Connector Part Number MS27468T17F6SN 3-Error! Bookmark not defined.
3.2.7.2.2.3-1 HRF Rack Power Output Ripple Voltage Spectrum 3-38
3.2.7.2.3-1 HRF Rack Power Output Trip Curves 3-39
3.2.7.3.1.1-1 HRF SIR Drawer Data Connector Part Number M83733/2RA131 3-43
3.2.7.3.1.2-1 HRF Rack Connector Panel J2 Data Connector Part Number MS27468T15F35S 3-Error! Bookmark not defined.
3.2.7.5.1.1-1 HRF Rack/Instrument Moderate Temperature Loop Interface 3-Error! Bookmark not defined.
3.2.7.6.1-1 HRF Rack VES and VRS Interface Connectors 3-Error! Bookmark not defined.
3.2.7.7.1.1-1 HRF Rack Nitrogen Interface Connectors 3-Error! Bookmark not defined.
3.2.7.9.3.2-1 Manual Fire Suppression Hardware Envelope 3-63
3.2.7.9.3.2-2 Closed Volume PFE Nozzle 3-64
3.3.6.4-1 Arm, Hand and Thumb/Finger Strength (5th Percentile Male Data) 3-71
3.3.6.4-2 Leg Strength at Various Knee and Thigh Angles (5th Percentile Male Data) 3-72
3.3.6.4-3 Torque Strength 3-72
3.3.6.5-1 Maximal Static Push Forces 3-Error! Bookmark not defined.
3.3.6.5-2 Male Grip Strength as a Function of the Separation Between Grip Elements 3-Error! Bookmark not defined.
3.3.6.7-1 Minimum Sizes for Access Openings for Fingers 3-73
3.3.6.33-1 Minimal Clearance for Tool-Operated Fasteners 3-79
3.3.6.44-1 Control Spacing Requirements for Ungloved Operation 3-81
3.3.6.45.4-1 Rotary Switch Guard 3-83
3.3.6.49-1 Valve Handle - Central Pivot Type 3-Error! Bookmark not defined.
3.3.6.49-2 Valve Handle - Lever Type 3-Error! Bookmark not defined.
3.3.6.50-1 Toggle Switches 3-85
3.3.6.51.4.3-1 Minimum IVA Handle Dimensions for IVA Applications 3-88
4.3.1.1-1 Qualification Thermal Cycling 4-4
4.3.1.2-1 Acceptance Thermal Cycling 4-5
ACRONYMS AND ABBREVIATIONS
|AC |Alternating Current |
|ADP |Acceptance Data Package |
|A |Ampere |
|ANSI |American National Standards Institute |
|APID |Application Process Identification |
|APM |Attached Pressurized Module |
|ASC |Aisle Stowage Container |
|ATT |Acceptance Thermal Test |
|ATV |Automated Transfer Vehicle |
|AVT |Acceptance Vibration Testing |
| | |
|C&DH |Command and Data Handling |
|CAM |Centrifuge Accommodation Module |
|CCB |Configuration Control Board |
|CCSDS |Consultative Committee for Space Data Systems |
|CFU |Colony Forming Units |
|CG |Center of Gravity |
|CI |Cargo Integration |
|CIL |Critical Items List |
|cm |centimeters |
|COTS |Commercial Off-the-Shelf |
|CTBE |Cargo Transfer Bag Equivalent |
| | |
|dB |Decibels |
|dBA |Acoustic Decibel Level |
|DC |Direct Current |
|DGCS |Display and Graphics Commonality Standards |
|dia |diameter |
|DR |Discrepancy Report |
|DRDs |Data Requirements Documents |
| | |
|EEE |Electrical, Electronic, and Electromechanical |
|EIA |Electronic Industry Association |
|EMC |Electromagnetic Compatibility |
|EMI |Electromagnetic Interference |
|EPCE |Electrical Power Consuming Equipment |
|ESD |Electrostatic Discharge |
|EVA |Extravehicular Activity |
|EXPRESS |EXpedite the PRocessing of Experiments to Space Station |
| | |
|fc |footcandle |
|FIAR |Failure Investigation Analysis Report |
ACRONYMS AND ABBREVIATIONS (Cont’d)
|FMEA |Failure Modes and Effects Analysis |
|FPD |Flight Projects Division |
|FSS |Fluid System Servicer |
|ft |feet |
| | |
|g |Gravity |
|GFCI |Ground Fault Circuit Interrupter |
|GHz |Gigahertz |
|GIDEP |Government and Industry Data Exchange Program |
|GPVP |Generic Payload Verification Plan |
|GSE |Ground Support Equipment |
| | |
|HR |Hazard Report |
|hr |Hour |
|HRD |Hardware Requirements Document |
|HRF |Human Research Facility |
|HRP |Human Research Program |
|Hz |Hertz |
| | |
|ICD |Interface Control Document |
|IDD |Interface Definition Document |
|IEEE |Institute of Electrical and Electronic Engineers |
|IMS |Inventory Management System |
|IMV |Intermodule Ventilation |
|in |inch |
|ISIS |International Subrack Interface Standards |
|ISPR |International Standard Payload Rack |
|ISS |International Space Station |
|ITCS |Internal Thermal Control System |
|IVA |Intravehicular Activity |
| | |
|JEM |Japanese Experiment Module |
|JSC |Johnson Space Center |
| | |
|kg |Kilogram |
|kHz |Kilohertz |
|kPa |KiloPascal |
|KSC |Kennedy Space Center |
| | |
|lb |pound |
|lbf |pounds force |
|lbm |Pounds Mass |
| | |
ACRONYMS AND ABBREVIATIONS (Cont’d)
|m/s |Meters Per Second |
|mA |Milliamperes |
|max |Maximum |
|MDM |Multiplexer-Demultiplexer Module |
|MDP |Maximum Design Pressure |
|MHz |Megahertz |
|MIL-ER |Military Established Reliability |
|min |minimum |
|min |minute |
|ML |milliliter |
|mm |millimeter |
|mm Hg |Millimeters of Mercury |
|MOTS |Modified Off-the-Shelf |
|MPLM |Mini Pressurized Logistics Module |
|MRDL |Medium Rate Data Link |
|ms |Milliseconds |
|MSFC |Marshall Space Flight Center |
|MTL |Moderate Temperature Loop |
|MUA |Material Usage Agreement |
| | |
|N |Newton (metric force measurement) |
|N/A |Not Applicable |
|N2 |Nitrogen |
|Nm |Nanometer |
|NASA |National Aeronautics and Space Administration |
|NASDA |National Space Development Agency of Japan |
|NSTS |National Space Transportation System (Do not use—use SSP) |
|NTSC |National Television Standards Committee |
| | |
|O2 |Oxygen |
|Oct |Octave |
|ORU |Orbital Replacement Unit |
| | |
|P/L |Payload |
|Pa |Pascal |
|PDA |Pre-Delivery Acceptance |
|PFE |Portable Fire Extinguisher |
|PHTR |Packaging, Handling, and Transportation Records |
|PIA |Payload Integration Agreement |
|PPC |Point-to-Point Communication |
|PRD |Program Requirements Document |
|psi |pounds per square inch |
|psia |pounds per square inch absolute |
|psig |pounds per square inch |
ACRONYMS AND ABBREVIATIONS (Cont’d)
|PSRP |Payload Safety Review Panel |
|PU |Panel Unit |
|PUL |Portable Utility Light |
| | |
|QAVT |Qualification for Acceptance Vibration Testing |
|QTT |Qualification Thermal Test |
|QVA |Qualification Vibration Analysis |
| | |
|Rad |Radiation Absorbed Dose |
|RIC |Rack Interface Controller |
|RMA |Reliability, Maintainability and Availability |
|rms |Root Mean Square |
|RSP |Resupply Stowage Platform |
|RSR |Resupply Stowage Rack |
| | |
|SD |Standard Deviation |
|SE&I |Systems Engineering and Integration |
|sec |second |
|SEE |Single Event Effect |
|SIR |Standard Interface Rack |
|SLPM |Standard Liter per Minute |
|SOW |Statement of Work |
|SPIP |Station Program Implementation Plan |
|SPL |Sound Pressure Level |
|SSPC |Solid State Power Controller |
| | |
|TBD |To Be Determined |
|TBR |To Be Resolved |
|TIA |Telecommunications Industry Association |
|TM |Technical Memo |
|TPS |Task Performance Sheet |
| | |
|UIP |Utility Interface Panel |
|UOP |Utility Outlet Panel |
|USL |United States Lab |
| | |
|V |Volts |
|VC-S |Visibly Clean - Sensitive |
|Vdc |Volts Direct Current |
|VDS |Verification Data Sheet |
|VES |Vacuum Exhaust System |
|VIPER drawer |VOILA Integrated Processor Electronics Rack drawer |
|VOILA |Visuomotor and Orientation Investigation on Long-duration Astronauts |
|VRS |Vacuum Resource System |
ACRONYMS AND ABBREVIATIONS (Cont’d)
|VVS |Vacuum Vent System |
| | |
|WGS |Waste Gas System |
|WS2 |HRF Workstation 2 |
|WSTF |White Sands Test Facility |
| | |
|ºC |Degrees Celsius |
|ºF |Degrees Fahrenheit |
| | |
|( |pi |
|(sec |Microsecond |
1.0 SCOPE
This specification defines the Human Research Facility (HRF) program requirements for Visuomotor and Orientation Investigation on Long-duration Astronauts (VOILA). The VOILA is a subrack payload that will be installed in an HRF rack and will use cameras mounted in the ISS module aisleway to record crew motion when exposed to visual stimulus.
The primary governing document for the requirements levied in this document is LS-71000, Program Requirements Document for the Human Research Facility.
The requirements in Sections 3, 4 and 5 of this document consist of a minimum set of constraints for the VOILA hardware and software.
The HRF Project Office is the controlling authority for this document. The HRF Configuration Control Board (CCB) or a delegated authority must approve any deviations from the requirements of this document.
2.0 APPLICABLE DOCUMENTS
The following applicable documents of the exact issue shown herein form a part of this specification to the extent specified herein. If a revision level or date is not cited, the latest version of the document should be used.
All specifications, standards, exhibits, drawings or other documents referenced in this specification are hereby incorporated as cited in the text of this document. Any updated revisions to documents specified herein shall be reviewed to determine the impact to the design. Changes to the design or this document shall only be made upon the direction of the HRF CCB.
2.1 Documents
|Document Number |Revision |Document Title |
|FED-STD-595 |Rev. B |Colors Used in Government Procurement |
| |12/89 | |
|JPG 5335.3 |Basic |Lyndon B. Johnson Space Center Quality Management System (QMS) |
|LS-60077 |TBR |Standard Interface Rack Specification |
|LS-71000 |Rev. B |Program Requirements Document for the Human Research Facility |
|LS-71011 |TBR |Acoustic Noise Control & Analysis Plan for Human Research Facility|
| | |Payloads and Racks |
|LS-71014 |TBR |Mass Properties Control Plan Human Research Facility Payload and |
| | |Racks |
|LS-71016 |TBR |Electromagnetic Compatibility Control Plan for the Human Research |
| | |Facility |
|LS-71020 |Rev. B Chg 1 |Software Development Plan for the Human Research Facility |
| |TBR | |
|MIL-PRF-19500 |Rev. M |Performance Specification Semiconductor Devices, General |
| |10/99 |Specification for |
|MIL-STD-810 |Rev. E |Environmental Test Methods and Engineering Guidelines |
| |7/95 | |
|MIL-STD-1686 |Rev. C |Electrostatic Discharge Control Program for Protection of |
| |10/95 |Electrical and Electronic Parts, Assemblies and Equipment |
| | |(Excluding Electrically Initiated Explosive Devices) |
|NASA TM 102179 |6/91 |Selection of Wires and Circuit Protective Devices for STS Orbiter |
| | |Vehicle Payload Electrical Circuits |
|NSTS/ISS 13830 |Rev. C, |Payload Safety Review and Data Submittal Requirements for Payloads|
| |Ch. 1 |Using the Space Shuttle and International Space Shuttle |
| |2/99 | |
|NSTS-1700.7 |Rev. B, Ch. 11 |Safety Policy and Requirements For Payloads Using the Space |
| |5/01 |Transportation System |
|NSTS-1700.7B |Basic, Ch. 4 |Safety Policy and Requirements For Payloads Using the |
|ISS ADDENDUM |8/02 |International Space Station |
|NSTS/ISS 18798 |Rev. B, Ch. 7 |Interpretations of NSTS/ISS Payload Safety Requirements |
| |2/00 | |
|NSTS-21000-IDD-MDK |Rev. B Chg 15 |Shuttle/Payload Interface Definition Document for Middeck |
| |10/02 |Accommodations |
|SN-C-0005 |Rev. D Chg 6 |Space Shuttle Contamination Control Requirements |
| |7/98 | |
|SP-T-0023 |Rev. C |Specification, Environmental Acceptance Testing |
| |05/01 | |
|SSP 30233 |Rev. F |Space Station Requirements for Materials and Processes |
| |7/99 | |
|SSP 30237 |Rev. F Chg 20 |Space Station Electromagnetic Emission and Susceptibility |
| |3/02 |Requirements |
|SSP 30240 |Rev. D |Space Station Grounding Requirements |
| |12/02 | |
|SSP 30242 |Rev. F |Space Station Cable/Wire Design and Control Requirements for |
| |12/02 |Electromagnetic Compatibility |
|SSP 30243 |Rev. G |Space Station Requirements for Electromagnetic Compatibility |
| |12/02 | |
|SSP 30245 |Rev. E, Ch. 16 |Space Station Electrical Bonding Requirements |
| |10/01 | |
|SSP 30312 |Rev. H, |Electrical, Electronic, and Electromechanical (EEE) and Mechanical|
| |Ch. 2 |Parts Management and Implementation Plan for Space Station Program|
| |11/02 | |
|SSP 30512 |Rev. C |Space Station Ionizing Radiation Design Environment |
| |9/94 | |
|SSP 30695 |Rev. A |Acceptance Data Package Requirements Specification |
| |01/95 | |
|SSP 41017 |Rev. F |Rack to Mini Pressurized Logistics Module Interface Control |
| |1/02 |Document (ICD) Part 1 |
|SSP 41175-2 |Rev. G |Software Interface Control Document (ICD) Part 1 Station |
| |2/03 |Management and Control to International Space Station Book 2, |
| | |General Software Interface Requirements |
|SSP 50005 |Rev. C, |International Space Station Flight Crew Integration Standard |
| |Ch. 8 |(NASA-STD-3000/T) |
| |9/01 | |
|SSP 50007 |Rev. B, |Space Station Inventory Management System Label Specification |
| |Ch. 2 | |
| |9/01 | |
|SSP 50008 |Rev. C |International Space Station Interior Color Scheme |
| |7/01 | |
|SSP 50313 |Draft |Display and Graphics Commonality Standard Document |
|SSP 50467 |Baseline |ISS Cargo Stowage Technical Manual: Pressurized Volume |
| |11/00 | |
|SSP 52005 |Rev. C |Payload Flight Equipment Requirements and Guidelines for |
| |12/01 |Safety-Critical Structures |
|SSP 52050 |Rev. E |Software Interface Control Document Part 1, International Standard|
| |1/03 |Payload Rack to International Space Station |
|SSP 57000 |Rev. E |Pressurized Payloads Interface Requirements Document |
| |11/00 | |
|SSP 57001 |Rev. C |Pressurized Payloads Hardware Interface Control Document Template |
| |10/00 | |
|SSQ 25002 |Rev. B 1/02 |Supplemental list of Qualified Electrical, Electronic, and |
| | |Electromechanical (EEE) Parts, Manufacturers, and Laboratories |
| | |(QEPM&L) |
2.2 Order of Precedence
In the event of a conflict between the text of this specification and references cited herein, the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.
3.0 SYSTEM REQUIREMENTS
3.1 Item Definition
The following items of VOILA will be designed and certified under this requirements document for use on International Space Station (ISS) as a part of the HRF program. The HRF Rack hardware used with this hardware is certified under separate documentation that is maintained by the appropriate program(s).
Table 3.1-1 lists the equipment items covered by this document, including the stowage kits that will be used to transport the items and contain the items on-orbit.
TABLE 3.1-1. EQUIPMENT ITEMS
|ITEM NAME |PART NUMBER |CLASS |QUANTITY |NOTES |
|VOILA INTEGRATED |SEG46119702-301 |I |3 |QUALIFICATION/TRAINER, FLIGHT, |
|PROCESSOR ELECTRONICS | | | |FLIGHT BACKUP |
|RACK (VIPER) DRAWER | | | |Electronics provided by PI |
| | | | |Chassis & integration provided |
| | | | |by NASA |
|Head Mounted Display |85-10100 |I |2 |Flight, Flight Backup |
|(HMD) | | | |Provided by PI |
|Headphones |85-41000 |I |2 |Flight, Flight Backup |
| | | | |Provided by PI |
|Subject Input Device |85-40600 |I |2 |Flight, Flight Backup |
|(SID) | | | |Provided by PI |
|Paddle |85-40500 |I |2 |Flight, Flight Backup |
| | | | |Provided by PI |
|Hand Switch |85-40530.01 |I |2 |Flight, Flight Backup |
| | | | |Provided by PI |
|Optical Tracker Camera |85-20100 |I |3 |Flight pair, Flight Backup |
|Bar | | | |single |
| | | | |Provided by PI |
|Chest Pack Interconnect|85-40400 |I |2 |Flight, Flight Backup |
|Box | | | |Provided by PI |
|Subject Restraint |SJG46119738-301 |I |2 |Flight, Flight Backup |
|System (SRS) Vest | | | |Provided by NASA |
|Subject Microphone |85-41100 |I |2 |Flight, Flight Backup |
| | | | |Provided by PI |
|Torso Marker Plate |85-40900 |I |1 |Flight only |
| | | | |Provided by PI |
|Spring Reel Assembly |SEG46119710-301 |I |4 |Flight pair, Flight Backup pair|
| | | | |Provided by NASA |
|SRS Platform |85-40301 |I |1 |Flight only |
| | | | |Provided by PI |
|SRS Quasi-free Float |85-40326 |I |1 |Flight only |
|Attachment | | | |Provided by PI |
|Subject Surveillance |85-41200 |I |2 |Flight, Flight Backup Provided |
|Camera | | | |by PI |
|W1, HRF to VIPER Data |85-40801 |I |1 |Flight only |
|Cable | | | |Provided by PI |
|W3, CODA to VIPER Cable|85-40803 |I |1 |Flight only |
| | | | |Provided by PI |
|W4, CODA to VIPER Cable|85-40804 |I |1 |Flight only |
| | | | |Provided by PI |
|W5, Platform to VIPER |85-40805 |I |1 |Flight only |
|Cable | | | |Provided by PI |
|W6, VIPER to Chest Pack|85-40806 |I |1 |Flight only |
|Cable | | | |Provided by PI |
|W7, Chest Pack to Torso|85-40807 |I |1 |Flight only |
|Cable | | | |Provided by PI |
|W8, Chest Pack to |85-40808 |I |1 |Flight only |
|Paddle | | | |Provided by PI |
|W9, Chest Pack to SID |85-40809 |I |1 |Flight only |
| | | | |Provided by PI |
|Head Mounted Display |85-10100 |III |2 |BDC, Training |
|(HMD) | | | |Provided by PI |
|Headphones |85-41000 |III |1 |BDC, Training |
| | | | |Provided by PI |
|Subject Input Device |85-40600 |III |1 |BDC, Training |
|(SID) | | | |Provided by PI |
|Paddle |85-40500 |III |1 |BDC, Training |
| | | | |Provided by PI |
|Hand Switch |85-40530.01 |III |1 |BDC, Training |
| | | | |Provided by PI |
|Optical Tracker Camera |85-20100 |III |2 |BDC, Training |
|Bar | | | |Provided by PI |
|Chest Pack Interconnect|85-40400 |III |1 |BDC, Training |
|Box | | | |Provided by PI |
|Subject Restraint |SJG46119738-301 |III |1 |BDC, Training |
|System (SRS) Vest | | | |Provided by NASA |
|Subject Microphone |85-41100 |III |1 |BDC, Training |
| | | | |Provided by PI |
|Torso Marker Plate |85-40900 |III |1 |BDC, Training Provided by PI |
|Spring Reel Assembly |SED46116446-301 |III |2 |BDC, Training |
| | | | |Provided by NASA |
|SRS Platform |85-40301 |III |1 |BDC, Training |
| | | | |Provided by PI |
|SRS Quasi-free Float |85-40326 |III |1 |BDC, Training |
|Attachment | | | |Provided by PI |
|Subject Surveillance |85-41200 |III |1 |BDC, Training Provided by PI |
|Camera | | | | |
|W1, HRF to VIPER Data |85-40801 |III |1 |BDC, Training |
|Cable | | | |Provided by PI |
|W3, CODA to VIPER Cable|85-40803 |III |1 |BDC, Training |
| | | | |Provided by PI |
|W4, CODA to VIPER Cable|85-40804 |III |1 |BDC, Training |
| | | | |Provided by PI |
|W5, Platform to VIPER |85-40805 |III |1 |BDC, Training |
|Cable | | | |Provided by PI |
|W6, VIPER to Chest Pack|85-40806 |III |1 |BDC, Training |
|Cable | | | |Provided by PI |
|W7, Chest Pack to Torso|85-40807 |III |1 |BDC, Training |
|Cable | | | |Provided by PI |
|W8, Chest Pack to |85-40808 |III |1 |BDC, Training |
|Paddle | | | |Provided by PI |
|W9, Chest Pack to SID |85-40809 |III |1 |BDC, Training |
| | | | |Provided by PI |
Table 3.1-2 lists the software items covered by this document.
Table 3.1-2. VOILA Software
|PROGRAM NAME |PART NUMBER |NOTES |
|VOILA SOFTWARE |TBD | |
3.1.1 Experiment Description
3.1.1.1 Experiment Overview
VOILA will extend, simplify, and merge two sensory motor and performance experiments originally developed for the 1998 STS-90 Neurolab mission. The two components retain separate numbers (E085/E507) on ISS, but are performed together. The experiments use the HRF Workstation 2 as “science kiosk” to perform short (typically 30 minute long) tests to study the role of visual, vestibular, and haptic cues on spatial orientation and motor behavior. The experiment utilizes virtual environment generation accessories first developed for the Neurolab as a tool to study these processes during and after long duration (3-6 month) orbital flight. Restrained and free-floating subjects wear a wide field of view, color stereo head mounded display. Protocols are based on 1-G paradigms, require little set-up time, and can be selected and performed by an astronaut in an automated fashion using Session Manager software. Pre-flight, in-flight, and post-flight performances of each protocol are planned on each ISS increment.
The Specific Objectives are to determine the effects of microgravity on:
1) The influence of scene symmetry, rotation, haptic cues, and expected orientation on static and dynamic self tilt (Virtual Tilting and Tumbling Room Protocols);
2) the onset of x-axis illusory linear self-motion without haptic cues (Linear Vection Protocol);
3) the effect of perceived orientation on visual object recognition and shape recognition (Object Recognition Protocols);
4) whether information used in grasping remembered objects is stored in head fixed, body fixed, or exocentric reference frames (Virtual Grasping Protocol); and
5) how the timing of catching movements depends on anticipation of downward acceleration (Virtual Catching Protocol).
The general hypothesis is that mental processes involved in self-orientation, object perception and motor control will be fundamentally altered in microgravity environments, as evidenced by visual reorientation, inversion, and proprioceptive illusions frequently reported in-orbit by astronauts. These experiments on self-orientation, linear vection, object perception and motor control will help to characterize the contribution of gravity to the mechanisms underlying these activities.
3.1.1.2 Operational Overview
In each session, based on the amount of crew time available, the Session Manager program suggests one or more of 5 different visual perception protocols and one or more of 4 different visuomotor tasks. In-flight protocols are performed in up to 3 possible conditions: quasi-free floating, lightly restrained, and/or with constant-force springs (simulated gravity).
Visual Perception
Protocol 1: Tilted Room. Subject indicates perceived vertical while viewing a series of tilted scenes.
Protocol 2: Tumbling Room. Subject indicates vection magnitude and surface identity while viewing rotating scenes.
Protocol 3: Linear Vection. Subject indicates vection onset and magnitude while viewing a moving corridor scene.
Protocol 4: Figures. Subject indicates which complex 2D figure seems most familiar.
Protocol 5: Shading. Subject indicates which shaded circle seems most convex.
Visuomotor Coordination
Protocol 6: Grasping. Upright. Subjects align the hand with an object oriented in 3D space.
Protocol 7: Grasping. Head Tilt. Subjects repeat Protocol 6 with 30( head tilt.
Protocol 8: Pointing. Subjects perform rapid point-to-point movements with the dominant hand.
Protocol 9: Interception. Subjects intercept a flying ball with the dominant hand.
The following protocols will only be performed pre-flight and post-flight:
Protocol 10: Tilted Bed. Subject aligns the bed to their subjective horizontal in a dark room.
Protocol 11: Luminous Line. Subjects align a luminous line to their subjective vertical meridian in a dark room.
Protocol 12: Tilted grasping. Subjects perform Protocol 6 while seated in a chair inclined by 30( in the frontal plane.
3.1.1.3 Hardware Overview
The VOILA experiment depicted in figure 3.1.1.3-1 will utilize the Human Research Facility Workstation 2 (WS2), which is a rack-mounted computer drawer located in HRF Rack 1 and Rack 2. The VOILA experiment will use the following components of the WS2:
1. The graphics accelerator cards in the WS2 are used to render virtual environments on the Head Mounted Display for the experiment protocols.
2. The WS2 sound card is used to record the subject’s audio notes.
3. The WS2 data acquisition card is used to capture acceleration data from the Paddle for the Interception protocol.
4. The USB ports of the WS2 are used to operate the head and body tracking system, the SID, and the Video Surveillance Camera.
5. The VOILA software will reside and operate on the WS2 hard drive.
The VOILA experiment also utilizes the HRF Flat Screen Display and the Workstation Keyboard to operate the VOILA Session Manager software and the HRF Common Software on the WS2.
VOILA uses the 4 PU VIPER Drawer to interface its peripherals to the HRF WS2. The PI-provided electronics are housed in a NASA-provided chassis. The electrical components include power converters, head and body tracker control boxes, USB-to-serial converter, and USB hub. The 4PU VIPER Drawer will be located in HRF Rack 1 or Rack 2, near the WS2. It receives 28 VDC power from the HRF rack, and is cooled by the HRF common fan.
The head and body tracker system is built from COTS components. It consists of two major systems: (1) an inertial tracking system based on the Intersense IS300 Pro tracking system and (2) an optical tracking system based on the Charnwood Dynamics CODA camera system. The inertial tracking system uses 1-4 inertial cubes containing linear accelerometers and angular rate sensors to detect orientation and position information. Inertial cubes are mounted on the HMD, on the Paddle, and in the Chest Pack. The optical tracking system provides a second source of position and orientation information by tracking a set of infrared LED markers with cameras. The infrared LED markers are mounted on the HMD, the Paddle, and the Chest Pack. Three cameras are mounted into each Optical Tracker Camera Bar, and two bars are used to track all of the sensors. The Optical Tracker Camera Bars are mounted into the seat track at opposite ends of the module such that the subject wearing the infrared LED markers is in between them. The information from the inertial and the optical systems are combined, resulting in an accurate determination of the objects’ position and orientation in space. The VIPER Drawer contains the CODA “Hub”, which controls the cameras and infrared LED markers, and Intersense control box, which integrates the information.
The Subject Restraint System (SRS) is composed of four parts which are used to restrain the subjects in certain postures, prevent them from drifting into other equipment, and provide haptic feedback for certain protocols. The four parts of the Subject Restraint System are the SRS Vest, the SRS Platform, the SRS Spring Reel Assemblies, and the SRS Quasi-free Float Attachment.
The SRS Vest is an adjustable vest worn by the subject. The vest has attachment points for the SRS Spring Reel Assemblies along its waist, and for the SRS Quasi-free Float Attachment on the front and back of the Vest near the wearer’s center of gravity. A number of adjustment straps on the Vest allow the subject to distribute the force from the SRS spring coils onto the waist and shoulders. The Vest has an attachment point for the Chest Pack, and attachment points for temporary stowage of the SID, the Hand Switch, and the Paddle. The Vest has an attachment point for a Torso Marker Plate, which is a metal plate with infrared LED sensors attached to track the subject’s upper torso.
The SRS Platform is an adjustable aluminum platform that mounts onto the seat tracks. A set of infrared LED markers is mounted on the Platform to provide a stationary reference frame for the optical tracking system. Subjects will stand on the SRS Platform when using the SRS Spring Reel Assemblies to simulate gravity in the Room and Vection protocols. It can be folded into a chair for the seated position, and unfolded into a bed for the supine position during the Grasping and Interception protocols. It has removable padding for comfort and wide Velcro straps for restraint.
The SRS Spring Reel Assemblies are two constant force springs that provide 30-40 lbs each of downward force to simulate the haptic sensations of gravity on the subject’s feet. One end of each spring is mounted into a slot on the SRS platform. The other end of each spring is attached to the bottom of the SRS Vest. The Spring Reel Assemblies were originally designed and used for the Neurolab E136 experiments.
The SRS Quasi-free Float Attachment is a pole, approximately 1 meter in length, which has an attachment point on one end that fits into a seat track. The other end has a swivel joint and a quick-release attachment point for the SRS vest. The swivel joint allows the subject to drift rotationally somewhat while “free-floating” but prevents them from drifting into other equipment or out of the head/body tracker’s working volume. The joint can also be locked to prevent large rotational motion.
The Chest Pack Interconnect Box is a connection box that is worn on the front of the SRS Vest. It has connections for devices that are used by the subject or mounted on the SRS Vest. It connects with the VIPER Drawer through one cable that provides power and data channels. The SID, paddle, HMD microphone, and a set of infrared LED markers on the SRS vest will connect into the Chest Pack Interconnect Box. The Chest Pack Interconnect Box will contain an inertial cube and have infrared LED markers mounted on its exterior.
The Head Mounted Display (HMD) is worn on the subject’s head and provides a stereoscopic display to the wearer. It is a modified Kaiser ProView80 LCD-based stereoscopic display with a large field of view (64 degrees horizontal x 48 degrees vertical). The HMDs used in the Neurolab E136 experiments are upgraded with lower power LCD displays, higher contrast units, and stronger space flight quality plastic frames. One inertial cube and several infrared LED markers will be mounted on the outer casing of the HMD. The HMD will connect to the front panel of the VIPER Drawer with two cables.
The Subject Microphone is a modified COTS computer microphone, used for subject voice recording. The Subject Microphone will be mounted to the HMD or the SRS Vest for hands-free operation.
The Headphones are modified COTS noise cancellation headphones. They will be worn with the HMD to suppress audio directionality cues.
The Subject Input Device (SID) is a modified COTS gamepad with two joysticks and several buttons. The SID will connect to the Chest Pack Interconnect Box. It will have an attachment point on the SRS Vest for temporary stowage. Subjects will respond to stimuli presented in the Room, Vection, Figures, and Shading protocols using the SID.
The Paddle is a custom-made interface device, consisting of a handle that can be gripped with either hand. In the dominant hand, the Paddle is used to measure hand movement, position and orientation during the Grasping and Interception protocols. The Paddle contains one inertial cube and a linear accelerometer to detect motion onsets. A set of infrared LED markers is mounted on the exterior. The Paddle is connected to the Chest Pack Interconnect Box through a single Y-cable that it shares with the Hand Switch.
The LPPA tilt chair
The Hand Switch is a modified COTS device with a single button that can be operated with either hand. During the Grasping and Interception protocols, it is held in the hand opposite the Paddle, and the button is pressed to trigger the beginning of a trial. The Hand Switch is connected to the Chest Pack Interconnect Box through a single Y-cable that it shares with the Paddle.
The Subject Surveillance Camera is a modified COTS device used to capture still images of the subject performing the experiment. It will be mounted to the wall or ceiling of the module with a seat track attachment.
[pic]
Figure 3.1.1.3-1 - VOILA hardware block diagram
3.2 Characteristics
3.2.1 Performance Characteristics
3.2.1.1 Functional Performance Characteristics
3.2.1.1.1 Audio/Video Outputs
A. VOILA shall provide stereoscopic video outputs via a head-mounted display.
B. VOILA shall provide the following:
1. identical monoaural outputs via left and right headphone speakers
2. module ambient noise as measured from a single area microphone.
2 Measurement Ranges
VOILA shall measure the following parameters within the following ranges:
A. module ambient noise 1-150 dB
B. subject voice 1-150 dB
C. joystick inputs
D. hand-held pushbutton inputs
E. subject head position 0-200 cm in three orthogonal axes
F. subject head orientation 0-359 degrees in three orthogonal axes
G. subject torso position 0-200 cm in three orthogonal axes
H. subject torso orientation 0-359 degrees in three orthogonal axes
I. restraint platform position 0-200 cm in three orthogonal axes
J. restraint platform orientation 0-359 degrees in three orthogonal axes
K. paddle position 0-200 cm in three orthogonal axes
L. paddle orientation 0-359 degrees in three orthogonal axes
M. paddle acceleration +/- 100 cm/s2
N subject surveillance photos
3.2.1.1.3 Measurement Accuracies
VOILA shall measure the following parameters with the following accuracies:
A. module ambient noise +/- 0 dB
B. subject voice +/- 0 dB
C. subject head position +/- 0.2 cm
D. subject head orientation +/- 0.1 deg
E. subject torso position +/- 0.2 cm
F. subject torso orientation +/- 0.15 deg
G. restraint platform position +/- 0.2 cm
H. restraint platform orientation +/- 0.15 deg
I. paddle position +/- 0.2 m
J. paddle orientation +/- 0.15 deg
K. paddle acceleration +/- 0.1 cm/s2
3.2.1.1.4 Measurement Frequencies
VOILA shall measure the following parameters at the following frequencies:
A. module ambient noise analog
B. subject voice analog
C. joystick inputs TBD
D. hand-held pushbutton inputs TBD
E. subject head position 60 Hz
F. subject head orientation 60 Hz
G. subject torso position 60 Hz
H. subject torso orientation 60 Hz
I. restraint platform position 60 Hz
J. restraint platform orientation 60 Hz
K. paddle position 60 Hz
L. paddle orientation 60 Hz
M. paddle acceleration 500 Hz
N. subject surveillance photos TBD
3.2.1.1.5 Physical Boundaries for Measurement Performance Characteristics
VOILA shall meet 3.2.1.1.2, 3.2.1.1.3, and 3.2.1.1.4 position and orientation measurements within a 2 meter x 2 meter x 2 meter cube.
3.2.1.1.6 Data Storage Frequencies
VOILA shall store the following with the following frequencies:
A. module ambient noise analog
B. subject voice analog
C. joystick inputs TBD Hz
D. hand-held pushbutton inputs TBD Hz
E. subject head position 60 Hz
F. subject head orientation 60 Hz
G. subject torso position 60 Hz
H. subject torso orientation 60 Hz
I. restraint platform position 60 Hz
J. restraint platform orientation 60 Hz
K. paddle position 60 Hz
L. paddle orientation 60 Hz
M. paddle acceleration 500 Hz
N. subject surveillance photos TBD
3.2.1.1.7 Data Storage Capacity
VOILA shall store parameters per 3.2.1.1.6 for:
A. durations of 30 minutes per session.
B. TBD sessions.
3.2.1.1.8 Data Storage – Return Logistics
VOILA data storage media shall be removable/replacable.
3.2.1.1.9 Data Downlink
VOILA shall downlink parameters stored per 3.2.1.1.6 via the HRF Workstation 2.
3.2.1.1.10 Software Update Uplink
VOILA shall uplink software updates for HRF Workstation 2 based VOILA experiment software.
3.2.1.1.11 Design
A. VOILA Head Mounted Display HMD shall be operable by subjects wearing eyeglasses.
B. VOILA shall allow the subject to make software menu selections.
C. VOILA subject input devices shall be operable via either hand.
D. VOILA equipment not worn or held by the subject shall mount to the ISS Seat Track.
E. VOILA shall provide a 35.0 lb +/- 1.0 lb load originating from the subject restraint platform to the subject with adjustable load distribution between the subject hips and shoulders. This requirement is only applicable when the subject is in the standing posture.
F. VOILA shall provide a quasi-free float attach structure which allows the subject rotational freedom about the subject attach point as acceptable to the Principal Investigator.
G. The VOILA quasi-free float attach structure shall be 1 meter +/- 0.1 meter.
H. VOILA shall provide a Subject Restraint Platform which:
1. provides a subject foot plate.
2. can be adjusted on-orbit to provide a subject seat with backrest and subject restraints.
3. can be adjusted on-orbit to provide a supine/prone plate with subject restraints.
3.2.2 Physical Characteristics
1 Mass and Center of Gravity Properties
1 VOILA Drawer Mass
The VOILA drawer mass shall be less than 64 pounds per set of slide guides, or a total of 64 pounds (29.03 kg).
2 VOILA Ancillary Hardware Mass
VOILA hardware to be stowed outside of the VOILA main housing shall meet the weight limitations of each M02 Bag, 200 lbf, when stowed as defined in section 3.2.2.2.1.B.
3.2.2.1.3 VOILA Drawer Center-of-Gravity Constraints
HRF rack mounted SIR drawer instruments shall meet the center of gravity constraints specified in Table 3.2.2.1.1-1, HRF SIR Drawer Center-of-Gravity Constraints. (LS-71000, Section 6.2.1.2.4)
3.2.2.2 Envelope
1. Stowed Envelope
A. VOILA’s main housing will consist of a single 4PU SIR drawer.
B. VOILA hardware to be stowed outside of the VOILA main housing shall fit within one M02 Transfer Bag, 34.25 in (W) x 20.5 in (D) x 19.5 in (H), in the VOILA stowed configuration. (NOTE: The VOILA platform (standing/supine) will be stowed outside the stowage bag.)
TABLE 3.2.2.1.1-1. HRF SIR DRAWER CENTER-OF-GRAVITY CONSTRAINTS
|DRAWER CONFIGURATION |X (IN) |X (IN) |Y (IN) |Y (IN) |Z (IN) |Z (IN) |
| |MIN. |MAX. |MIN. |MAX. |MIN. |MAX. |
|SINGLE SLIDE DRAWER (4 PU) |-1.75 |+1.75 |+7.99 |+12.00 |-0.63 |+0.87 |
|DOUBLE SLIDE DRAWER (8 PU) |-2.20 |+2.20 |+10.24 |+14.00 |+1.675 |+3.975 |
|TRIPLE SLIDE DRAWER (12 PU) |-1.50 |+1.50 |+9.74 |+13.00 |+6.37 |+8.87 |
|NOTE: CENTER OF GRAVITY ENVELOPE IS MEASURED FROM THE DRAWER COORDINATE SYSTEM AS DEFINED BELOW. THE GEOMETRIC CENTER FOR “Z” |
|AXIS IS MEASURED FROM THE CENTERLINE OF THE BOTTOM-MOST RAIL TOWARD THE TOP OF THE DRAWER. TOTAL MAXIMUM INTEGRATED MASS |
|(INCLUDING DRAWER, CONTENTS AND SLIDES) ON ANY ONE SET OF SLIDES IS LIMITED TO 64 POUNDS. MULTIPLE-SLIDE DRAWERS ARE TO EVENLY |
|DISTRIBUTE LOADING BETWEEN THE SETS OF SLIDES. |
| |
|[pic] |
| |
3.2.2.2.2 Deployed Envelope
3.2.2.2.2.1 On-Orbit Payload Protrusions
Definitions for on-orbit permanent protrusions, on-orbit semi-permanent protrusions, on-orbit temporary protrusions, on-orbit momentary protrusions, and protrusions for on-orbit keep alive payloads can be found in Section 6.1, Definitions. The requirements in Section 3.2.2.2.2.1 apply to installation and operation activities, but not to maintenance activities.
NOTE: The on-orbit protrusion requirements in this section are applicable to when the payload is on-orbit and do not apply to other phases of the transportation of the payload (e.g., launch, landing, Mini Pressurized Logistics Module (MPLM) installation). (LS-71000, Section 6.2.1.1.5)
A. On-orbit protrusions, excluding momentary protrusions, shall not extend laterally across the edges of the rack or pass between racks. (LS-71000, Section 6.2.1.1.5.A)
B. The integrated rack hardware, excluding momentary protrusions, shall not prevent attachment of Reliability, Maintainability and Availability (RMA) on any seat track attach holes. (LS-71000, Section 6.2.1.1.5.B)
Constraints which may be associated with payload protrusions include:
• removal of the protrusion during rack installation, translation, and crew translation
• removal of the protrusion if RMA is installed on the rack
• removal of the protrusion to prevent interference with microgravity operations
• removal or powering off of the rack if the protrusion blocks Portable Fire Extinguisher (PFE) access or the fire indicator
• may limit the rack location (e.g., Protrusion located in the floor and the ceiling are limited to a total of no more than 12 inches.)
• may limit operation of the payload
As is indicated by the constraints above, protrusions have a negative impact on crew operations and are to be minimized. (LS-71000, Section 6.2.1.1.5)
3.2.2.2.2.1.1 On-Orbit Permanent Protrusions
Not applicable to VOILA.
3.2.2.2.2.1.2 On-Orbit Semi-Permanent Protrusions
A. SIR and International Subrack Interface Standard (ISIS) drawer handles shall remain within the envelope shown in Figure 3.2.2.2.2.1.2-1. (LS-71000, Section 6.2.1.1.5.2.A) Note: VOILA will take exception to this requirement.
B. Other on-orbit semi-permanent protrusions shall be limited to no more than 500 square inches within the envelope shown in Figure 3.2.2.2.2.1.2-2. (LS-71000, Section 6.2.1.1.5.2.B) Note: VOILA will take exception to this requirement.
NOTE: The sum of the on-orbit semi-permanent protrusions and the on-orbit protrusion for keep alive payloads is limited to no more than 500 square inches. (LS-71000, Section 6.2.1.1.5.2.B)
NOTE: The SIR and ISIS drawer handles are not included in the 500 square inch limit. (LS-71000, Section 6.2.1.1.5.2.B)
C. All on-orbit semi-permanent protrusions shall be designed to be removable by the crew with hand operations and/or standard Intravehicular Activity (IVA) tools. (LS-71000, Section 6.2.1.1.5.2.C)
[pic]
Figure 3.2.2.2.2.1.2-1. SIR and ISIS Drawer Handles Protrusion Envelope
[pic]
3. All sections mentioned in figure refer to the applicable section of SSP57000E.
Figure 3.2.2.2.2.1.2-2. On-Orbit Semi-Permanent Protrusions Envelope
3.2.2.2.2.1.3 On-Orbit Temporary Protrusions
A. On-orbit temporary protrusions shall remain within the envelope shown in Figure 3.2.2.2.2.1.3-1. (LS-71000, Section 6.2.1.1.5.3.A) Note: VOILA will take exception to this requirement.
B. The combination of all on-orbit temporary protrusions for the integrated rack shall be designed such that they can be eliminated or returned to their stowed configuration by the crew with hand operations and/or standard IVA tools within 10 minutes. (LS-71000, Section 6.2.1.1.5.3.B)
NOTE: Integrated racks must provide stowage for on-orbit temporary protrusions within their stowage allocation. (LS-71000, Section 6.2.1.1.5.3)
NOTE: On-orbit temporary protrusions for payloads located in the floor or ceiling are limited to 6 inches each or a total of 12 inches for both floor and ceiling. (LS-71000, Section 6.2.1.1.5.3)
[pic]
4. All sections mentioned in figure refer to the applicable section of SSP57000E.
Figure 3.2.2.2.2.1.3-1. On-Orbit Temporary Protrusions Envelope
3.2.2.2.2.1.4 On-Orbit Momentary Protrusions
Not applicable to VOILA.
2 Deployed Envelope Dimensions
There are no requirements for deployed envelope dimensions beyond those documented in section 3.2.2.2.2.1.
3.2.3 Reliability, Quality and Non-Conformance Reporting
A. Not applicable to VOILA.
B. Quality
1. Quality Assurance for VOILA hardware developments, handling, or testing at JSC shall be implemented in accordance with JPG 5335.3, “JSC Quality Manual”. (LS-71000, Section 7.3.1)
2. Quality Assurance for VOILA hardware developments, handling, or testing at MIT shall be implemented in accordance with the following contract: . (LS-71000, Section 7.3.1)
C. Non-Conformance Reporting
1. For flight hardware produced under a contract or subcontract at a site other than JSC, non-conformance reporting requirements shall be specified in the Statement of Work (SOW) Data Requirements List, and Data Requirements Documents (DRDs) shall be used to identify the submittal and data requirements. (LS-71000, Section 7.3.2.1)
2. For flight hardware developed at JSC, non-conformance reporting shall be in accordance with JPG 5335.3 and the applicable technical division plan. (LS-71000, Section 7.3.2.2)
3. Non-conformances, which meet the Level 1 Problem Reporting and Corrective Action criteria for payloads as defined in SSP 30223, shall be reported in accordance with SSP 30223. (LS-71000, Section 7.3.2.3)
4. Software non-conformance reporting shall be in accordance with LS-71020-1, “Software Development Plan for the Human Research Facility.” (LS-71000, Section 7.3.2.4)
3.2.3.1 Failure Propagation
The design shall preclude propagation of failures from the payload to the environment outside the payload. (NSTS 1700.7B, Section 206)
3.2.3.2 Useful Life
VOILA hardware shall be designed for a 10 year utilization. (LS-71000, Section 7.2.1)
3.2.3.2.1 Operational Life (Cycles)
Operational life applies to any hardware that deteriorates with the accumulation of operating time and/or cycles and thus requires periodic replacement or refurbishment to maintain acceptable operating characteristics. Operational life includes the usage during flight, ground testing and pre-launch operations. All components of VOILA shall have an operational life limit of 10 years, except those identified as having limited life, see Section 3.2.3.2.3.
3.2.3.2.2 Shelf Life
Shelf life is defined as that period of time during which the components of a system can be stored under controlled conditions and put into service without replacement of parts (beyond servicing and installation of consumables). Shelf life items shall be identified and tracked on a list that is maintained as a part of the hardware acceptance data pack.
3.2.3.2.3 Limited Life
Limited life is defined as the life of a component, subassembly, or assembly that expires prior to the stated useful life in Section 3.2.3.2.1. Limited life items or materials, such as soft goods, shall be identified and the number of operation cycles shall be determined. Limited life items shall be tracked on a limited life list that is maintained as a part of the hardware acceptance data pack.
3.2.4 Maintainability
A. Not applicable to VOILA.
B. Not applicable to VOILA.
C. Not applicable to VOILA.
D. Electrical connectors and cable installations shall permit disconnection and reconnection without damage to wiring connectors. (LS-71000, Section 6.4.4.3.2C)
E. Not applicable to VOILA.
F. Not applicable to VOILA.
G. The capture elements, including grids, screens, or filter surfaces shall be accessible for replacement or cleaning without dispersion of the trapped materials. (LS-71000, Section 6.4.3.1.2B)
3.2.4.1 Logistics and Maintenance
3.2.4.1.1 Payload In-Flight Maintenance
Not applicable to VOILA.
3.2.4.1.2 Maintenance
3.2.5 Environmental Conditions
3.2.5.1 On-Orbit Environmental Conditions
3.2.5.1.1 On-Orbit Internal Environments
3.2.5.1.1.1 Pressure
VOILA shall be safe when exposed to pressures of 0 to 104.8 kPa (0 to 15.2 psia). (LS-71000, Section 6.2.9.1.1)
3.2.5.1.1.2 Temperature
VOILA shall be safe when exposed to the temperatures of 10 to 46 oC (50 to 115 oF). (LS-71000, Section 6.2.9.1.2)
3.2.5.1.1.3 Humidity
Not applicable to VOILA.
3.2.5.1.2 Use of Cabin Atmosphere
3.2.5.1.2.1 Active Air Exchange
Not applicable to VOILA.
3.2.5.1.2.2 Oxygen Consumption
Not applicable to VOILA.
3.2.5.1.2.3 Chemical Releases
Chemical releases to the cabin air shall be in accordance with Paragraphs 209.1a and 209.1b in NSTS 1700.7, ISS Addendum. (LS-71000, Section 6.2.9.2.3)
3.2.5.1.2.4 Cabin Air Heat Leak
Cabin air heat rejection is defined by the ISS program at the module level only. Instrument cabin air heat leak must be coordinated with HRF SE&I. (LS-71000, Section 6.2.5.4)
3.2.5.1.3 Ionizing Radiation Requirements
3.2.5.1.3.1 Instrument Contained or Generated Ionizing Radiation
Equipment containing or using radioactive materials or that generate ionizing radiation shall comply with NSTS 1700.7, ISS Addendum, Paragraph 212.1. (LS-71000, Section 6.2.9.3.1)
3.2.5.1.3.2 Ionizing Radiation Dose
Instruments should expect a total dose (including trapped protons and electrons) of 30 Rads (Si) per year of ionizing radiation. A review of the dose estimates in the ISS (SAIC-TN-9550) may show ionizing radiation exposure to be different than 30 Rads (Si) per year, if the intended location of the rack in the ISS is known. (LS-71000, Section 6.2.9.3.2)
NOTE: This is a testing guideline and is not a verifiable requirement.
3.2.5.1.3.3 Single Event Effect (SEE) Ionizing Radiation
VOILA shall be designed not to produce an unsafe condition or one that could cause damage to equipment external to VOILA as a result of exposure to SEE ionizing radiation assuming exposure levels specified in SSP 30512, Paragraph 3.2.1, with a shielding thickness of 25.4 mm (1000 mils). (LS-71000, Section 6.2.9.3.3)
3.2.5.1.4 Additional Environmental Conditions
The environmental information provided in Table 3.2.5.1.4-1, Environmental Conditions on ISS, and Figure 3.2.5.1.4-1, Operating Limits of the ISS Atmospheric Total Pressure, Nitrogen and Oxygen Partial Pressures, is for design and analysis purposes. (LS-71000, Section 6.2.9.4)
TABLE 3.2.5.1.4-1. ENVIRONMENTAL CONDITIONS ON ISS
|ENVIRONMENTAL CONDITIONS |VALUE |
|ATMOSPHERIC CONDITIONS ON ISS | |
|PRESSURE EXTREMES |0 TO 104.8 KPA (0 TO 15.2 PSIA) |
|NORMAL OPERATING PRESSURE |SEE FIGURE 3.2.5.1.4-1 |
|OXYGEN PARTIAL PRESSURE |SEE FIGURE 3.2.5.1.4-1 |
|NITROGEN PARTIAL PRESSURE |SEE FIGURE 3.2.5.1.4-1 |
|DEWPOINT |4.4 TO 15.6 (C (40 TO 60 (F) REF. FIGURE 3.2.5.1.1.3-1 |
|PERCENT RELATIVE HUMIDITY |25 TO 75 % REF. FIGURE 3.2.5.1.1.3-1 |
|CARBON DIOXIDE PARTIAL PRESSURE DURING NORMAL OPERATIONS WITH 6 |24-HR AVERAGE EXPOSURE 5.3 MM HG |
|CREWMEMBERS PLUS ANIMALS |PEAK EXPOSURE 7.6 MM HG |
|CARBON DIOXIDE PARTIAL PRESSURE DURING CREW CHANGEOUT WITH 11 |24-HR AVERAGE EXPOSURE 7.6 MM HG |
|CREWMEMBERS PLUS ANIMALS |PEAK EXPOSURE 10 MM HG |
|CABIN AIR TEMPERATURE IN USL, JEM, APM AND CAM |17 TO 28 (C (63 TO 82 (F) |
|CABIN AIR TEMPERATURE IN NODE 1 |17 TO 31 (C (63 TO 87 (F) |
|AIR VELOCITY (NOMINAL) |0.051 TO 0.203 M/S (10 TO 40 FT/MIN) |
|AIRBORNE MICROBES |LESS THAN 1000 CFU/M3 |
|ATMOSPHERE PARTICULATE LEVEL |AVERAGE LESS THAN 100,000 PARTICLES/FT3 FOR PARTICLES LESS THAN 0.5 MICRONS |
| |IN SIZE |
|MPLM AIR TEMPERATURES |PASSIVE FLIGHTS |ACTIVE FLIGHTS |
|PRE-LAUNCH |15 TO 24 (C (59 TO 75.2 (F) |14 TO 30 (C (57.2 TO 86 (F) |
|LAUNCH/ASCENT |14 TO 24 (C (57.2 TO 75.2 (F) |20 TO 30 (C (68 TO 86 (F) |
|ON-ORBIT (CARGO BAY + DEPLOYMENT) |24 TO 44 (C (75.2 TO 111.2 (F) |16 TO 46 (C (60.8 TO 114.8 (F) |
|ON-ORBIT (ON-STATION) |23 TO 45 (C (73.4 TO 113 (F) |16 TO 43 (C (60.8 TO 109.4 (F) |
|ON-ORBIT (RETRIEVAL + CARGO BAY) |17 TO 44 (C (62.6 TO 111.2 (F) |11 TO 45 (C (51.8 TO 113 (F) |
|DESCENT/LANDING |13 TO 43 (C (55.4 TO 109.4 (F) |10 TO 42 (C (50 TO 107.6 (F) |
|POST-LANDING |13 TO 43 (C (55.4 TO 109.4 (F) |10 TO 42 (C (50 TO 107.6 (F) |
|FERRY FLIGHT |15.5 TO 30 (C (59.9 TO 86 (F) |15.5 TO 30 (C (59.9 TO 86 (F) |
|MPLM MAXIMUM DEWPOINT TEMPERATURES | | |
|PRE-LAUNCH |13.8 (C (56.8 (F) |12.5 (C (54.5 (F) |
|LAUNCH/ASCENT |13.8 (C (56.8 (F) |12.5 (C (54.5 (F) |
|ON-ORBIT (CARGO BAY +DEPLOYMENT) |13.8 (C (56.8 (F) |12.5 (C (54.5 (F) |
|ON-ORBIT (ON STATION) |15.5 (C (60 (F) |15.5 (C (60 (F) |
|ON-ORBIT (RETRIEVAL +CARGO BAY) |10 (C (50 (F) |10 (C (50 (F) |
|DESCENT/LANDING |10 (C (50 (F) |10 (C (50 (F) |
|POST LANDING |10 (C (50 (F) |10 (C (50 (F) |
|FERRY FLIGHT |15.5 (C (60 (F) |15.5 (C (60 (F) |
|THERMAL CONDITIONS | |
|USL MODULE WALL TEMPERATURE |13 (C TO 43 (C (55 (F TO 109 (F) |
|JEM MODULE WALL TEMPERATURE |13 (C TO 45 (C (55 (F TO 113 (F) (TBR) |
|APM MODULE WALL TEMPERATURE |13 (C TO 43 (C (55 (F TO 109 (F) (TBR) |
|CAM MODULE WALL TEMPERATURE |13 (C TO 43 (C (55 (F TO 109 (F) (TBR) |
|OTHER INTEGRATED PAYLOAD RACKS |FRONT SURFACE LESS THAN 37 (C (98.6 (F) |
|*MICROGRAVITY | |
|QUASI-STEADY STATE ENVIRONMENT |SEE SSP 57000 FIGURES 3.9.4 AND TABLE 3.9.4 |
|VIBRO-ACCOUSTIC ENVIRONMENT |SEE SSP 57000 FIGURE 3.9.4 |
|GENERAL ILLUMINATION |108 LUX (10 FC) MEASURED 30 INCHES FROM THE FLOOR IN THE CENTER OF THE AISLE |
[pic]
Figure 3.2.5.1.4-1. Operating Limits of the ISS Atmospheric Total Pressure,
Nitrogen and Oxygen Partial Pressures
3.2.5.1.5 Pressure Rate of Change
A. VOILA shall maintain positive margins of safety for the on-orbit depress/repress rates in Table 3.2.5.1.5-1. (LS-71000, Section 6.2.1.1.6B)
Table 3.2.5.1.5-1. ISS Pressure Rate of Change
|DEPRESSURIZATION |878 PA/SEC (7.64 PSI/MINUTE) |
|REPRESSURIZATION |230 PA/SEC (2.0 PSI/MINUTE) |
B. VOILA shall maintain positive margins of safety for maximum depressurization and repressurization rates for the carrier(s) in which it will be transported. (LS-71000, Section 6.2.1.1.6B)
1. VOILA shall maintain positive margins of safety for maximum depressurization and repressurization rates for the MPLM documented in Table 3.2.5.1.5-2. (Derived from LS-71000, Section 6.2.1.1.6A)
Table 3.2.5.1.5-2. MPLM Pressure Rate of Change
|DEPRESSURIZATION |890 PA/SEC (7.75 PSI/MINUTE) |
|REPRESSURIZATION |800 PA/SEC (6.96 PSI/MINUTE) |
2. VOILA shall maintain positive margins of safety for maximum depressurization and repressurization rates for the Orbiter Middeck documented in Table 3.2.5.1.5-3. (LS-71000, Section 6.3.1.2A)
Table 3.2.5.1.5-3. Orbiter Middeck Pressure
Rate of Change
|DEPRESSURIZATION/REPRESSURIZATION |1031 PA/SEC (9.0 PSI/MINUTE) |
C. VOILA shall maintain positive margins of safety when exposed to the PFE discharge rate given in Figure 3.2.5.1.5-1. (LS-71000, Section 6.2.1.1.6C)
D. Not applicable to VOILA.
[pic]
Figure 3.2.5.1.5-1. Manual Fire Suppression System Performance Characteristics
3.2.5.1.6 Microgravity
Microgravity requirements have not been determined by the ISS Program.
A. Quasi-Steady Requirements
TBD (LS-71000, Section 6.2.1.1.7A)
B. Vibratory Requirements
TBD (LS-71000, Section 6.2.1.1.7B)
C. Transient Requirements
TBD (LS-71000, Section 6.2.1.1.7C)
3.2.5.2 Acoustic Emission Limits
3.2.5.2.1 Continuous Noise Limits
A. Integrated Racks Whose Sub-Rack Equipment Will Not Be Changed Out
Not applicable to VOILA.
B. Integrated Racks Whose Sub-Rack Equipment Will Be Changed Out
The Continuous Noise Source (see Glossary of Terms) for an integrated rack (including any supporting adjunct active portable equipment operated outside the integrated rack that is within or interfacing with the crew habitable volume) whose sub-rack equipment will be changed out on-orbit shall not, except in those cases when the rack meets the Intermittent Noise Source requirements specified in Section 3.2.5.2.2, exceed the limits specified in Table 3.2.5.2.1-1 for all octave bands (NC-40 equivalent) when the equipment is operating in the loudest expected configuration and mode of operation that can occur on orbit under nominal crew, or hardware operation circumstances, during integrated rack setup operations, or during nominal operations where doors/panels are opened or removed. (LS-71000, Section 6.4.3.3.1B)
NOTE: These acoustic requirements do not apply during failure or maintenance operations. (LS-71000, Section 6.4.3.3.1)
C. Independently Operated Equipment
Not applicable to VOILA.
Table 3.2.5.2.1-1. Continuous Noise Limits
|RACK NOISE LIMITS MEASURED AT 0.6 METERS DISTANCE FROM THE TEST ARTICLE |
|FREQUENCY BAND |INTEGRATED RACK SOUND PRESSURE LEVEL |
|(HZ) |(SPL) |
|63 |64 |
|125 |56 |
|250 |50 |
|500 |45 |
|1000 |41 |
|2000 |39 |
|4000 |38 |
|8000 |37 |
3.2.5.2.2 Intermittent Noise Limits
A. The Integrated rack (including any supporting adjunct active portable equipment operated outside the integrated rack that is within or interfacing with the crew habitable volume) Intermittent Noise Source (See Glossary of Terms) shall not exceed the Total Rack A-weighted Sound Pressure Level (SPL) Limits during the Maximum Rack Noise Duration as specified in Table 3.2.5.2.2-1 when the equipment is operating in the loudest expected configuration and mode of operation that can occur on orbit under any planned operations. (LS-71000, Section 6.4.3.3.2A)
NOTE: These acoustic requirements do not apply during failure or maintenance operations. (LS-71000, Section 6.4.3.3.2)
B. The Rack Noise Duration is the total time that the rack produces intermittent noise above the NC-40 limit during a 24 hour time period. This duration is the governing factor in determining the allowable Intermittent Noise Limits. Regardless of the number of separate sources and varying durations within a rack, this cumulative duration shall be used to determine the A-weighted SPL limit in column B. (LS-71000, Section 6.4.3.3.2B)
TABLE 3.2.5.2.2-1. INTERMITTENT NOISE LIMITS
|RACK NOISE LIMITS MEASURED |
|AT 0.6 METERS DISTANCE FROM THE TEST ARTICLE |
|MAXIMUM RACK NOISE DURATION |TOTAL RACK A - WEIGHTED SPL (DBA) |
|8 HOURS |49 |
|7 HOURS |50 |
|6 HOURS |51 |
|5 HOURS |52 |
|4 HOURS |54 |
|3 HOURS |57 |
|2 HOURS |60 |
|1 HOUR |65 |
|30 MINUTES |69 |
|15 MINUTES |72 |
|5 MINUTES |76 |
|2 MINUTES |78 |
|1 MINUTE |79 |
|NOT ALLOWED |80 |
3.2.5.3 Lighting Design
The general illumination of the space station in the aisle will be a minimum of 108 lux (10 foot candles) of white light. This illumination will be sufficient for ordinary payload operations performed in the aisle (e.g., examining dials or panels, reading procedures, transcription, tabulation, etc.).
Payloads will meet the following requirements:
A. Payload work surface specularity shall not exceed 20 percent. Paints listed in Table 3.2.5.3-1 meet this requirement. (LS-71000, Section 6.4.3.4A)
B. Not applicable to VOILA.
C. Not applicable to VOILA.
D. Not applicable to VOILA.
E. Not applicable to VOILA.
TABLE 3.2.5.3-1. SURFACE INTERIOR COLORS AND PAINTS
|HARDWARE DESCRIPTION |COLOR |FINISH |PAINT SPECIFICATION PER |
| | | |FED-STD-595 |
|EQUIPMENT RACK UTILITY PANEL RECESS |WHITE |SEMIGLOSS |27925 |
|EQUIPMENT RACK UTILITY PANEL TEXT CHARACTERS |BLACK |LUSTERLESS |37038 |
|ISPR UTILITY PANEL RECESS |WHITE |SEMIGLOSS |27925 |
|ISPR UTILITY PANEL RECESS TEXT CHARACTERS |BLACK |LUSTERLESS |37038 |
|FUNCTIONAL UNIT UTILITY PANEL RECESS (AS APPLICABLE) |WHITE |SEMIGLOSS |27925 |
|FUNCTIONAL UNIT UTILITY PANEL RECESS TEXT CHARACTERS |BLACK |LUSTERLESS |37038 |
|RACK FRONT AISLE EXTENSIONS |OFF-WHITE |SEMIGLOSS |27722 |
|OVERHEAD RACK FACE PLATES |OFF-WHITE |SEMIGLOSS |27722 |
|PORT RACK FACE PLATES |OFF-WHITE |SEMIGLOSS |27722 |
|STARBOARD RACK FACE PLATES |OFF-WHITE |SEMIGLOSS |27722 |
|DECK RACK FACE PLATES |OFF-WHITE |SEMIGLOSS |27722 |
|OVERHEAD RACK UTILITY PANEL CLOSEOUTS |OFF-WHITE |SEMIGLOSS |27722 |
|PORT RACK UTILITY PANEL CLOSEOUTS |OFF-WHITE |SEMIGLOSS |27722 |
|STARBOARD RACK UTILITY PANEL CLOSEOUTS |OFF-WHITE |SEMIGLOSS |27722 |
|DECK RACK UTILITY PANEL CLOSEOUTS |OFF-WHITE |SEMIGLOSS |27722 |
|STOWAGE TRAYS |OFF-WHITE |SEMIGLOSS |27722 |
|STOWAGE TRAY HANDLE STRAPS (ANY LOCATION) |BLUE MATERIAL |SEMIGLOSS |25102 OR EQUIV. |
|COMMON SEAT TRACK INTERFACE |CLEAR (ANODIZED) |SEMIGLOSS |NONE |
|GLOVEBOX (ALUMINUM OR PLASTIC) |MEDIUM GRAY |GLOSS |16329 OR 16373 |
|GLOVEBOX (ALUMINUM) |WHITE |GLOSS |17925 |
|GLOVEBOX (ALUMINUM OR PLASTIC) |OFF-WHITE |GLOSS |17722 |
|GLOVEBOX (ALUMINUM) |TAN |GLOSS |10475 |
|EXPRESS PROGRAM RACK UTILITY PANELS |OFF-WHITE |GLOSS |17875 |
3.2.5.4 Front Panel Surface Temperature
VOILA shall be designed such that the average front surface temperature is less than 37 °C (98.6 °F) with a maximum temperature limit not to exceed 49 °C (120 °F). (LS-71000, Section 6.2.5.3)
3.2.6 Transportability
3.2.6.1 Launch and Landing
VOILA shall be transportable to and from orbit via the Shuttle middeck and the EXPRESS Transportation Rack.
3.2.7 Operational Interface Requirements
3.2.7.1 Mechanical Interface Requirements
3.2.7.1.1 Connector Physical Mate
Not applicable to VOILA.
3.2.7.1.2 HRF Rack to SIR Drawer Structural Interface Requirements
HRF rack SIR drawer accommodations are shown in Figure 3.2.7.1.2-1. (LS-71000, Section 6.2.1.2)
[pic]
NOTE: SIR drawer accommodations viewed from front of the HRF rack.
Figure 3.2.7.1.2-1. HRF Rack SIR Drawer Accommodations
3.2.7.1.2.1 Dimensional Tolerances
HRF rack mounted SIR drawer dimensional tolerances shall be in accordance with Table 3.2.7.1.2.1-1. (LS-71000, Section 6.2.1.2.1)
TABLE 3.2.7.1.2.1-1. DIMENSIONAL TOLERANCES
|ENGLISH DIMENSION |TOLERANCE |
|X.XX |±0.030 |
|X.XXX |±0.010 |
|Xº |±1º |
3.2.7.1.2.2 SIR Drawer Structural/ Mechanical Interfaces
HRF rack mounted SIR drawers shall meet the structural mechanical interfaces as defined in LS-60077, Standard Interface Rack Specification. (LS-71000, Section 6.2.1.2.2)
3.2.7.1.2.3 Reserved
3.2.7.1.2.4 HRF Rack Seat Track Interfaces
VOILA hardware interfacing with the ISS seat track shall meet ISS seat track dimensional requirements.
3.2.7.2 Electrical Power Interface Requirements
Electrical requirements in this section are defined for instrument interfaces to the HRF rack 28 volt power outputs at HRF rack connector bars and rack connector panel. For the purposes of this section, compatibility means to remain safe and to provide operational functions within the range of accuracy specified for the instrument. (LS-71000, Section 6.2.2)
3.2.7.2.1 HRF Rack Power Output Connectors
3.2.7.2.1.1 SIR Drawer Power Connectors
SIR drawer instruments that receive electrical power from HRF rack connector bar interfaces shall connect to and be compatible with blind mate connector part number M83733/2RA018 with pin assignments as shown Figure 3.2.7.2.1.1-1 and Table 3.2.7.2.1.1-1. (LS-71000, Section 6.2.2.1.1)
[pic]
Figure 3.2.7.2.1.1-1. SIR Drawer Power Connector
Part Number M83733/2RA018
TABLE 3.2.7.2.1.1-1. SIR DRAWER POWER CONNECTOR PIN ASSIGNMENTS
|PIN |TYPE |FUNCTION |NOTE |
|1 |CORE |+28 VDC SUPPLY |0 TO 20 AMPERES |
|2 |CORE |+28 VDC RETURN | |
|3 | |NOT USED | |
|4 | |NOT USED | |
|5 | |NOT USED | |
|6 | |NOT USED | |
|7 | |NOT USED | |
|8 | |NOT USED | |
|9 | |NOT USED | |
|10 | |NOT USED | |
|11 | |NOT USED | |
|12 |CORE |CHASSIS GROUND | |
|13 | |NOT USED | |
|14 | |NOT USED | |
|15 | |NOT USED | |
|16 | |NOT USED | |
|17 | |NOT USED | |
|18 | |NOT USED | |
3.2.7.2.1.2 Rack Connector Panel J1 Power Connector
Not applicable to VOILA.
3.2.7.2.2 Voltage Characteristics
3.2.7.2.2.1 Steady-State Operating Voltage Envelope
HRF rack dependent instruments shall be compatible with steady-state voltages within the range of +25.5 volts to + 29.5 volts. (LS-71000, Section 6.2.2.2.1)
3.2.7.2.2.2 Transient Operating Voltage Envelope
HRF rack dependent instruments shall be compatible with transient voltages within the range of +23.5 volts to + 30.5 volts for 60 ms. (LS-71000, Section 6.2.2.2.2)
3.2.7.2.2.3 Ripple Voltage/Noise Characteristics
A. HRF rack dependent instruments shall be compatible with a 1 volt peak to peak ripple in supply voltages within the ranges specified for steady-state and transient voltage envelopes. (LS-71000, Section 6.2.2.2.3A)
B. HRF rack dependent instruments shall be compatible with the ripple voltage spectrum shown in Figure 3.2.7.2.2.3-1. (LS-71000, Section 6.2.2.2.3B)
[pic]
Figure 3.2.7.2.2.3-1. HRF Rack Power Output Ripple Voltage Spectrum
3.2.7.2.3 Maximum Current Limit
HRF rack dependent instruments shall be compatible with the maximum current provided for the selected current rating (5A, 10A, 15A, 20A) shown in Figure 3.2.7.2.3-1. (LS-71000, Section 6.2.2.3)
[pic]
NOTES:
1) Current limit region shown above is defined for a capacitor load charge. In a direct short condition the actual trip time is 1/2 of the values shown.
2) For a progressive short in which the change in current has a slow rise time, an absolute maximum current limit of 2.5 times the normal current limit is provided. The time to trip for this condition is dictated by the I2 x t trip limit.
3) Final current limit is obtained with in 100 (secs. and the initial current limit is a maximum of 2 times the final.
4) The current limit is 39.0A +/-20%.
5) The trip values for the long-duration portion of the trip curves are a nominal 120% of range. (LS-71000, Section 6.2.2.3)
Figure 3.2.7.2.3-1. HRF Rack Power Output Trip Curves
3.2.7.2.4 Reverse Current
HRF rack dependent instrument reverse current shall not exceed the following values at each 28 V power interface:
A. 600A pulse with a duration less than 10 (s.
B. 450A peak with a duration less than 1 ms.
C. 2A continuous.
(LS-71000, Section 6.2.2.4)
3.2.7.2.5 Reverse Energy
HRF rack dependent instrument reverse energy shall not exceed 4 Joules at HRF rack 28 V power interfaces. (LS-71000, Section 6.2.2.5)
3.2.7.2.6 Capacitive Loads
HRF rack dependent instrument capacitive loads shall not exceed 50 microFarad per Ampere of rated output current at SIR drawer and rack connector panel power interfaces. (LS-71000, Section 6.2.2.6)
3.2.7.2.7 Electromagnetic Compatibility (EMC)
VOILA shall meet the payload provider applicable requirements of SSP 30243, Paragraphs 3.1 and 3.6.2. (LS-71000, Section 6.2.2.8)
3.2.7.2.7.1 Electrical Grounding
VOILA hardware connected to Interface B or Interface C shall meet all requirements specified in Section 3 of SSP 30240. (LS-71000, Section 6.2.2.8.1)
NOTE: HRF mandates that grounding isolation requirements which are applicable at the rack level are also applicable at the subrack and rack dependent hardware levels for quality assurance purposes.
3.2.7.2.7.2 Electrical Bonding
Electrical bonding of the VOILA shall be in accordance with Class H ans Class S in SSP 30245 and NSTS 1700.7, ISS Addendum, Sections 213 and 220. (LS-71000, Section 6.2.2.8.2)
3.2.7.2.7.3 Electromagnetic Interference
A. VOILA shall meet all EMI requirements of SSP 30237. (LS-71000, Section 6.2.2.8.4)
NOTE: The alternative use of RS03 stated below applies to radiated susceptibility requirements only. (LS-71000, Section 6.2.2.8.4)
B. Alternately, the payload Electrical Power Consuming Equipment (EPCE) may choose to accept a minimal increase of EMI risk with a somewhat less stringent Electric Field Radiated Susceptibility (RS03) requirement on equipment considered to be non-safety critical to the vehicle and crew. The tailored RS03 requirement, shown in Table 3.2.7.2.7.3-1 below, will hereafter be denoted RS03PL. (LS-71000, Section 6.2.2.8.4)
table 3.2.7.2.7.3-1. RS03PL
|FREQUENCY |RS03PL LIMIT (V/M) |
|14 KHZ - 400 MHZ |5 |
|400 MHZ - 450 MHZ |30 |
|450 MHZ - 1 GHZ |5 |
|1 GHZ - 5 GHZ |25 |
|5 GHZ - 6 GHZ |60 |
|6 GHZ - 10 GHZ |20 |
|13.7 GHZ - 15.2 GHZ |25 |
Comments:
1. The less stringent RS03PL limit was developed to envelope the electric fields generated by ISS transmitters and ground-based radars tasked to perform space surveillance and tracking. Ground-based radars that are not tasked to track the ISS and search radars that could momentarily sweep over the ISS are not enveloped by the relaxed RS03PL. For most scientific payloads, the minimal increase of EMI risk for the reduced limits is acceptable. The RS03PL limit does not account for module electric field shielding effectiveness that could theoretically reduce the limits even more. Although shielding effectiveness exists, it is highly dependent on the EPCE location within the module with respect to ISS windows. (LS-71000, Section 6.2.2.8.4)
2. The conducted susceptibility requirements CS01, CS02 and CS06 are also used as the local stability requirements in SSP 57000 Paragraph 3.2.2.10. (LS-71000, Section 6.2.2.8.4)
3.2.7.2.8 Electrostatic Discharge
A. Unpowered VOILA EPCE shall not be damaged by Electrostatic Discharge (ESD) equal to or less than 4000 V to the case or any pin on external connectors. (LS-71000, Section 6.2.2.9)
B. VOILA EPCE that may be damaged by ESD between 4000 V and 15,000 V shall have a label affixed to the case in a location clearly visible in the installed position. (LS-71000, Section 6.2.2.9)
C. Labeling of VOILA EPCE susceptible to ESD up to 15,000 V shall be in accordance with MIL-STD-1686. (LS-71000, Section 6.2.2.9)
NOTE: These voltages are the result of charges that may be accumulated and discharged from ground personnel or crewmembers during equipment installation or removal. (LS-71000, Section 6.2.2.9)
3.2.7.2.9 Corona
Not applicable to VOILA.
3.2.7.2.10 Cable/Wire Design and Control Requirements
Cabling between the VOILA and Interface B or Interface C shall meet all Cable and Wire requirements of SSP 30242. (LS-71000, Section 6.2.2.8.3)
3.2.7.2.10.1 Wire Derating
A. Circuit element derating criteria for instruments connected to HRF rack 28 volt power outlets shall be per NASA Technical Memo (TM) 102179 as interpreted by NSTS 18798, TA-92-038. (LS-71000, Section 6.2.2.7.1A).
B. Circuit element derating shall be based on the maximum trip current for a 20 A Solid State Power Controller (SSPC) as specified in Figure 3.2.7.2.3-1. (LS-71000, Section 6.2.2.7.1B)
3.2.7.2.10.2 Exclusive Power Feeds
Cabling shall not occur between Interface C connected EPCE with Interface B; and/or Interface B with Interface C. (LS-71000, Section 6.2.2.7.2)
3.2.7.2.11 Loss of Power
VOILA shall fail safe in the event of a total or partial loss of power, regardless of the availability of Auxiliary power in accordance with NSTS 1700.7, ISS Addendum. (LS-71000, Section 6.2.2.7.3)
3.2.7.2.12 Alternating Current Magnetic Fields
The generated Alternating Current (AC) magnetic fields, measured at a distance of 7 centimeters (cm) from the generating equipment, shall not exceed 140 dB above 1 picotesla for a frequency at 30 Hz, then falling 26.5 dB per decade to 3.5 KHz and 85 dB for frequencies ranging from 3.5 kHz to 50 kHz. (LS-71000, Section 6.2.2.10)
3.2.7.2.13 Direct Current Magnetic Fields
The generated Direct Current (DC) magnetic fields shall not exceed 170 dB picotesla at a distance of 7 cm from the generating equipment. This applies to electromagnetic and permanent magnetic devices. (LS-71000, Section 6.2.2.11)
3.2.7.3 Command and Data Handling Interface Requirements
3.2.7.3.1 HRF Rack Data Connectors
3.2.7.3.1.1 SIR Drawer Data Connectors
HRF rack dependent instruments requiring HRF rack data services at SIR drawer connector bar locations shall connect to blind mate connector part number M83733/2RA131, with pin assignments shown in Figure 3.2.7.3.1.1-1 and Table 3.2.7.3.1.1-1. (LS-71000, Section 6.2.3.1.1)
[pic]
Figure 3.2.7.3.1.1-1. HRF SIR Drawer Data Connector
Part Number M83733/2RA131
TABLE 3.2.7.3.1.1-1. HRF SIR DRAWER DATA
CONNECTOR PIN ASSIGNMENTS
|PIN |INTERFACE |FUNCTION |
|1-3 |NOT USED | |
|4 |DISCRETE 1 (+) |HIGH BI-DIRECTIONAL |
|5 |DISCRETE 2 (+) |HIGH BI-DIRECTIONAL |
|6-8 |NOT USED | |
|9 |CONTINUITY DISCRETE (+) | |
|10-12 |NOT USED | |
|13 |DISCRETE 1 (-) |LOW BI-DIRECTIONAL |
|14 |DISCRETE 2 (-) |LOW BI-DIRECTIONAL |
|15-23 |NOT USED | |
|24 |ANALOG 1 (+) |HIGH |
|25-32 |NOT USED | |
|33 |DISCRETE (SHIELD) |SHIELD |
|34-43 |NOT USED | |
|44 |ANALOG 1 (-) |LOW |
|45-46 |NOT USED | |
|47 |RS170 (+) |VIDEO 1 FROM DRAWER HIGH |
|48-50 |NOT USED | |
|51 |PPC BUS 01 (+) (DAISY-CHAIN) |HIGH |
|52-56 |NOT USED | |
|57 |RS170 (SHIELD) |VIDEO 1 FROM DRAWER SHIELD |
|58-60 |NOT USED | |
|61 |PPC BUS 01 (-) (DAISY-CHAIN) |LOW |
|62 |PPC BUS 02 (-) (DAISY-CHAIN) |LOW |
|63-66 |NOT USED | |
|67 |TIA/EIA RS-422 TX (+) |LINER TX HIGH |
|68 |RS170 (-) |VIDEO 1 FROM DRAWER LOW |
|69-70 |NOT USED | |
|71 |PPC BUS 01 (SHIELD) (DAISY-CHAIN) |SHIELD |
|72 |NOT USED | |
|73 |PPC BUS 02 (SHIELD) (DAISY CHAIN) |SHIELD |
|74 |NOT USED | |
|75 |ANALOG (SHIELD) |SHIELD |
|76 |NOT USED | |
TABLE 3.2.7.3.1.1-1. HRF SIR DRAWER DATA
CONNECTOR PIN ASSIGNMENTS (CONT’D)
|Pin |Interface |Function |
|77 |TIA/EIA RS-422 TX (shield) |Liner TX Shield |
|78 |TIA/EIA RS-422 RX (+) |Liner RX High |
|79-82 |Not used | |
|83 |PPC Bus 02 (+) (Daisy chain) |High |
|84-87 |Not used | |
|88 |TIA/EIA RS-422 TX (-) |Liner TX Low |
|89 |TIA/EIA RS-422 RX (shield) |Liner RX Shield |
|90-91 |Not used | |
|92 |PPC Bus 03 (shield) (Transformer-coupled bus) |Shield |
|93 |PPC Bus 03 (+) (Transformer-coupled bus) |High |
|94-98 |Not used | |
|99 |TIA/EIA RS-422 RX (-) |Liner RX Low |
|100-102 |Not used | |
|103 |PPC Bus 03 (-) (Transformer-coupled bus) |Low |
|104 |Not used | |
|105 |Ethernet RX (+) |Liner Hub Receive + |
|106-112 |Not used | |
|113 |PPC Bus 04 (+) (Transformer-coupled bus) |High |
|114 |PPC Bus 04 (shield) (Transformer-coupled bus) |Shield |
|115 |Not used | |
|116 |Ethernet RX (-) |Liner Hub Receive - |
|117 |Not used | |
|118 |Ethernet TX (shield) |Liner Hub Transmit shield |
|119-120 |Not used | |
|121 |Continuity Discrete (-) | |
|122-123 |Not used | |
|124 |PPC Bus 04 (-) (Transformer-coupled bus) |Low |
|125 |Not used | |
|126 |Ethernet RX (shield) |Liner Hub Receive shield |
|127 |Not used | |
|128 |Ethernet TX (+) |Liner Hub Transmit high |
|129 |Ethernet TX (-) |Liner Hub Transmit low |
|130-131 |Not used | |
3.2.7.3.1.2 HRF Rack Connector Panel J2 Data Connector
Not applicable to VOILA.
3.2.7.3.2 HRF Ethernet Interfaces
Not applicable to VOILA.
3.2.7.3.3 HRF TIA/EIA-422 Interfaces
Not applicable to VOILA.
3.2.7.3.4 HRF Bi-Directional Discretes Interfaces
Not applicable to VOILA.
3.2.7.3.5 HRF Analog Interfaces
Rack dependent instruments that require differential analog interfaces at the rack connector panel or at SIR drawer connector bars shall be compatible with signal characteristics of -5 Vdc to +5 Vdc with a selectable sampling rate of 1, 10 or 100 Hz. (LS-71000, Section 6.2.3.5)
3.2.7.3.6 HRF Software Requirements
This section contains the software requirements for the Computer Software Configuration Items (CSCIs) associated with the VOILA experiment. Each software requirement shall be traceable back to a functional requirement in this HRD. The requirements traceability matrix is shown in Table 3.2.7.3.6-1 below. The requirements allocation matrix is shown in Table 3.2.7.3.6-2. The verification process for each requirement is listed in the Certification Matrix (Appendix C). The type, category, and operational modes required shall be identified for each CSCI.
TABLE 3.2.7.3.6-1 requirements traceability matrix
|HRD REQUIREMENT IDENTIFIER |CSCI REQUIREMENTS |
|3.2.1.1.1 A |3.2.7.3.6.5.1 A, 3.2.7.3.6.6.1 A |
|3.2.1.1.2 A |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 B |3.2.7.3.6.4.1 K, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 C |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 D |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 E |3.2.7.3.6.4.1 N, 3.2.7.3.6.4.1 O, 3.2.7.3.6.4.1 P, |
| |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 F |3.2.7.3.6.4.1 N, 3.2.7.3.6.4.1 O, 3.2.7.3.6.4.1 P, |
| |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 G |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 H |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 I |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 J |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 K |3.2.7.3.6.4.1 P, 3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, |
| |3.2.7.3.6.6.1 H |
|3.2.1.1.2 L |3.2.7.3.6.4.1 P, 3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, |
| |3.2.7.3.6.6.1 H |
|3.2.1.1.2 M |3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.2 N |3.2.7.3.6.4.1 M, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 A |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 B |3.2.7.3.6.4.1 K, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 C |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 D |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 E |3.2.7.3.6.4.1 N, 3.2.7.3.6.4.1 O, 3.2.7.3.6.4.1 P, |
| |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 F |3.2.7.3.6.4.1 N, 3.2.7.3.6.4.1 O, 3.2.7.3.6.4.1 P, |
| |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 G |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 H |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 I |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 J |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 K |3.2.7.3.6.4.1 P, 3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, |
| |3.2.7.3.6.6.1 H |
|3.2.1.1.3 L |3.2.7.3.6.4.1 P, 3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, |
| |3.2.7.3.6.6.1 H |
|3.2.1.1.3 M |3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.3 N |3.2.7.3.6.4.1 M, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 A |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 B |3.2.7.3.6.4.1 K, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 C |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 D |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 E |3.2.7.3.6.4.1 N, 3.2.7.3.6.4.1 O, 3.2.7.3.6.4.1 P, |
| |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 F |3.2.7.3.6.4.1 N, 3.2.7.3.6.4.1 O, 3.2.7.3.6.4.1 P, |
| |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 G |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 H |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 I |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 J |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 K |3.2.7.3.6.4.1 P, 3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, |
| |3.2.7.3.6.6.1 H |
|3.2.1.1.4 L |3.2.7.3.6.4.1 P, 3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, |
| |3.2.7.3.6.6.1 H |
|3.2.1.1.4 M |3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.4 N |3.2.7.3.6.4.1 M, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 A |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 B |3.2.7.3.6.4.1 K, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 C |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 D |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 E |3.2.7.3.6.4.1 N, 3.2.7.3.6.4.1 O, 3.2.7.3.6.4.1 P, |
| |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 F |3.2.7.3.6.4.1 N, 3.2.7.3.6.4.1 O, 3.2.7.3.6.4.1 P, |
| |3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 G |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 H |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 I |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 J |3.2.7.3.6.4.1 P, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 K |3.2.7.3.6.4.1 P, 3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, |
| |3.2.7.3.6.6.1 H |
|3.2.1.1.6 L |3.2.7.3.6.4.1 P, 3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, |
| |3.2.7.3.6.6.1 H |
|3.2.1.1.6 M |3.2.7.3.6.4.1 Q, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.6 N |3.2.7.3.6.4.1 M, 3.2.7.3.6.5.1 G, 3.2.7.3.6.6.1 H |
|3.2.1.1.11 B |3.2.7.3.6.5.1 D |
TABLE 3.2.7.3.6-2 requirements allocation matrix
|CSCI REQUIREMENTS |HRD REQUIREMENT IDENTIFIER |
|3.2.7.3.6.4.1 B |3.2.1.1.11 B |
|3.2.7.3.6.4.1 K |3.2.1.1.2 B, 3.2.1.1.3 B, 3.2.1.1.4 B, 3.2.1.1.6 B |
|3.2.7.3.6.4.1 M |3.2.1.1.2 N, 3.2.1.1.3 N, 3.2.1.1.4 N, 3.2.1.1.6 N |
|3.2.7.3.6.4.1 N |3.2.1.1.2 E, 3.2.1.1.2 F, 3.2.1.1.3 E, 3.2.1.1.3 F, |
| |3.2.1.1.4 E, 3.2.1.1.4 F, 3.2.1.1.6 E, 3.2.1.1.6 F |
|3.2.7.3.6.4.1 O |3.2.1.1.2 E, 3.2.1.1.2 F, 3.2.1.1.3 E, 3.2.1.1.3 F, |
| |3.2.1.1.4 E, 3.2.1.1.4 F, 3.2.1.1.6 E, 3.2.1.1.6 F |
|3.2.7.3.6.4.1 P |3.2.1.1.2 E, 3.2.1.1.2 F, 3.2.1.1.2 G, 3.2.1.1.2 H, |
| |3.2.1.1.2 I, 3.2.1.1.2 J, 3.2.1.1.2 K, 3.2.1.1.2 L, |
| |3.2.1.1.3 E, 3.2.1.1.3 F, 3.2.1.1.3 G, 3.2.1.1.3 H, |
| |3.2.1.1.3 I, 3.2.1.1.3 J, 3.2.1.1.3 K, 3.2.1.1.3 L, |
| |3.2.1.1.4 E, 3.2.1.1.4 F, 3.2.1.1.4 G, 3.2.1.1.4 H, |
| |3.2.1.1.4 I, 3.2.1.1.4 J, 3.2.1.1.4 K, 3.2.1.1.4 L, |
| |3.2.1.1.6 E, 3.2.1.1.6 F, 3.2.1.1.6 G, 3.2.1.1.6 H, |
| |3.2.1.1.6 I, 3.2.1.1.6 J, 3.2.1.1.6 K, 3.2.1.1.6 L |
|3.2.7.3.6.4.1 Q |3.2.1.1.2 K, 3.2.1.1.2 L, 3.2.1.1.2 M, 3.2.1.1.3 K, |
| |3.2.1.1.3 L, 3.2.1.1.3 M, 3.2.1.1.4 K, 3.2.1.1.4 L, |
| |3.2.1.1.4 M, 3.2.1.1.6 K, 3.2.1.1.6 L, 3.2.1.1.6 M |
|3.2.7.3.6.5.1 A |3.2.1.1.1 A |
|3.2.7.3.6.5.1 D |3.2.1.1.11 B |
|3.2.7.3.6.5.1 G |3.2.1.1.2, 3.2.1.1.3, 3.2.1.1.4, 3.2.1.1.6 |
|3.2.7.3.6.6.1 A |3.2.1.1.1 A |
|3.2.7.3.6.6.1 E |3.2.1.1.11 B |
|3.2.7.3.6.6.1 H |3.2.1.1.2, 3.2.1.1.3, 3.2.1.1.4, 3.2.1.1.6 |
3.2.7.3.6.1 Definitions
Please refer to the Software Development Plan for the Human Research Facility (LS-71020) for definitions of the Software Type, Software Category, and Configuration Item terms.
3.2.7.3.6.2 Modes
Ground Mode – The Ground Mode is the mode in which the software operates during baseline data collection. Twelve protocols will be performed during baseline data collection.
Flight Mode- The Flight Mode is the mode in which the software operates during flight. Nine protocols will be performed during flight.
3.2.7.3.6.3 Notes
None.
3.2.7.3.6.4 Session Manager CSCI
The Session Manager CSCI is flight software, which resides on the HRF Workstation 2. The software is provided by the Principal Investigator.
The Session Manager manages crew identification and setup information, and allows a subject to select from an automated list of experiment protocols, or to select a single experiment protocol. It launches the appropriate Experiment Manager to perform the selected protocol. The Session Manager arranges for experiment data downlinking through HRF Common Software. It also provides explanation and help about the VOILA experiment. The Session Manager provides hardware adjustment functions for the Web Surveillance Camera, Optical Tracker Camera Bar, Paddle, and tracking hardware on the Head Mounted Display.
3.2.7.3.6.4.1 CSCI Functional and Performance Requirements
Listed below are the functional and performance requirements specific to the Session Manager.
A. The Session Manager shall operate on the HRF Flat Screen Display.
Note: It is not necessary for the Session Manager menus to be clearly readable in the head mounted display.
B. The Session Manager menus shall be navigable with the HRF Workstation 2 keyboard.
C. The Session Manager shall require the subject to enter crew identification.
D. The Session Manager shall require the subject to enter or correct the date.
E. The Session Manager shall recommend a session protocol, physical set up, and test procedure according to a preplanned sequence of experimental trials.
F. The Session Manager shall allow the subject to choose a specific protocol to execute.
G. The Session Manager shall launch the Experiment Manager that corresponds with the selected protocol.
H. The Session Manager shall launch only one Experiment Manager protocol at a time.
I. The Session Manager shall display the number and type of protocols completed by the current subject.
J. The Session Manager shall allow the subject to enter written comments with the HRF Workstation 2 keyboard.
K. The Session Manager shall allow the subject to enter recorded voice comments with the microphone.
L. The Session Manager shall allow the subject to adjust the headphone volume.
M. The Session Manager shall allow the subject to configure and control the Subject Surveillance Camera.
N. The Session Manager shall allow the subject to configure, calibrate, and test the function of the infrared LED markers mounted on the Head Mounted Display.
O. The Session Manager shall allow the subject to configure, calibrate, and test the function of the inertial cube mounted on the Head Mounted Display.
P. The Session Manager shall allow the subject to configure, calibrate, and test the function of the Optical Tracker Camera Bar.
Q. The Session Manager shall allow the subject to configure, calibrate, and test the function of the Paddle.
3.2.7.3.6.4.2 CSCI External Interface Requirements
Listed below are the external interface software requirements for the Session Manager.
A. The Session Manager will interface with HRF Common Software. This external interface shall be used to initiate the execution of the Session Manager. The interface is defined in the Interface Design Document (IDD) for the HRF Common Software (LS-71062-8).
B. The Session Manager will interface with HRF Common Software. This external interface shall be used to place files on the downlink list. The interface is defined in the Interface Design Document for the HRF Common Software (LS-71062-8).
C. The Session Manager will interface with the E085 Experiment Manager. This external interface shall be used to initiate the execution of the E085 Experiment Manager. The interface is defined in the Interface Control Document for the VOILA Session Manager (VSM).
D. The Session Manager will interface with the E507 Experiment Manager. This external interface shall be used to initiate the execution of the E507 Experiment Manager. The interface is defined in the Interface Control Document for the VOILA Session Manager (VSM).
3.2.7.3.6.4.2.1 Word/Byte Notations, Types and Data Transmissions
3.2.7.3.6.4.2.1.1 Word/Byte Notations
The Session Manager shall use the word/byte notations as specified in paragraph 3.1.1, Notations in SSP 52050. (LS-71000, Section 6.1.3.1.1)
3.2.7.3.6.4.2.1.2 Data Types
The Session Manager shall use the data types as specified in paragraph 3.2.1 and subsections, Data Formats in SSP 52050. (LS-71000, Section 6.1.3.1.2)
3.2.7.3.6.4.2.1.3 Service Requests
The Session Manager shall request services in accordance with LS-71062-8, Interface Definition Document for the HRF Common Software (LS-71000, Section 6.1.3.3.1.5).
3.2.7.3.6.4.3 CSCI Internal Interface Requirements
The Session Manager internal interfaces are defined by the Principal Investigator.
3.2.7.3.6.4.4 CSCI Internal Data Requirements
The Session Manager internal data requirements are defined by the Principal Investigator.
3.2.7.3.6.4.5 CSCI Adaptation Requirements
There are no CSCI adaptation requirements for the Session Manager.
3.2.7.3.6.4.6 Software Safety Requirements
The Session Manager CSCI shall not be used to hold, store, or process any safety critical parameters or commands.
3.2.7.3.6.4.7 Data Privacy Requirements
There are no CSCI data privacy requirements for the Session Manager.
3.2.7.3.6.4.8 CSCI Environment Requirements
A. The Session Manager shall execute in the environment described in the HRF Workstation 2 Interface Definition Document, LS-71042-14-4A.
B. The Session Manager shall utilize a maximum amount of 25 MB of disk space.
C. The Session Manager shall utilize a maximum amount of 8 MB of Random Access Memory (RAM).
3.2.7.3.6.4.9 Software Quality Factors
The Session Manager executable shall generate consistent results given the same initialization data.
3.2.7.3.6.4.10 Design and Implementation Constraints
The HRF HCI Design Guide (LS-71130) should be considered when designing displays for the Session Manager.
User interface software associated with the Session Manager will comply with the Display and Graphics Commonality Standards (DGCS) (SSP 50313, ).
3.2.7.3.6.4.11 Precedence and Criticality of Requirements
All requirements are equally weighted and are not listed in any order of precedence or criticality.
3.2.7.3.6.5 E085 Experiment Manager CSCI
The E085 Experiment Manager CSCI is flight software, which resides on the HRF Workstation 2. The software is provided by the Principal Investigator.
The E085 Experiment Manager is launched by the Session Manager. It displays the visual stimuli for the E085 experiment protocols and interacts with the Subject Input Device and the tracking hardware on the Head Mounted Display. It instructs the subject on when and how to make responses, and records these responses during the protocol. Upon completion of the protocol, the E085 Experiment Manager returns control to the Session Manager.
3.2.7.3.6.5.1 CSCI Functional and Performance Requirements
Listed below are the functional and performance requirements specific to the E085 Experiment Manager.
A. The E085 Experiment Manager shall be viewable in the left eye and the right eye of the Head Mounted Display.
B. The E085 Experiment Manager shall render the visual images that make up the Tilted Room, Tumbling Room, Linear Vection, Figures, and Shading protocols in flight mode and in ground mode.
C. The E085 Experiment Manager shall change the WS2 screen resolution to the appropriate resolution and color depth for the experiment protocol.
D. The E085 Experiment Manager menus shall be navigable with the Subject Input Device.
E. The E085 Experiment Manager scene shall respond to subject hand movements while the subject is holding the Subject Input Device.
F. The E085 Experiment Manager scene shall respond to subject head movements while the subject is wearing the head mounted display.
G. The E085 Experiment Manager shall log experiment data collected during the current protocol.
3.2.7.3.6.5.2 CSCI External Interface Requirements
Listed below are the external interface software requirements for the E085 Experiment Manager.
The E085 Experiment Manager will interface with the Session Manager. This external interface shall be used to initiate the execution of the E085 Experiment Manager. The interface is defined in the Interface Control Document for the VOILA Session Manager (VSM).
3.2.7.3.6.5.2.1 Word/Byte Notations, Types and Data Transmissions
3.2.7.3.6.5.2.1.1 Word/Byte Notations
The E085 Experiment Manager shall use the word/byte notations as specified in paragraph 3.1.1, Notations in SSP 52050. (LS-71000, Section 6.1.3.1.1)
3.2.7.3.6.5.2.1.2 Data Types
The E085 Experiment Manager shall use the data types as specified in paragraph 3.2.1 and subsections, Data Formats in SSP 52050. (LS-71000, Section 6.1.3.1.2)
3.2.7.3.6.5.2.1.3 Service Requests
The E085 Experiment Manager shall request services in accordance with LS-71062-8, Interface Definition Document for the HRF Common Software (LS-71000, Section 6.1.3.3.1.5).
3.2.7.3.6.5.3 CSCI Internal Interface Requirements
The E085 Experiment Manager internal interfaces are defined by the Principal Investigator.
3.2.7.3.6.5.4 CSCI Internal Data Requirements
The E085 Experiment Manager internal data requirements are defined by the Principal Investigator.
3.2.7.3.6.5.5 CSCI Adaptation Requirements
There are no CSCI adaptation requirements for the E085 Experiment Manager.
3.2.7.3.6.5.6 Software Safety Requirements
The E085 Experiment Manager CSCI shall not be used to hold, store, or process any safety critical parameters or commands.
3.2.7.3.6.5.7 Data Privacy Requirements
There are no CSCI data privacy requirements for the E085 Experiment Manager.
3.2.7.3.6.5.8 CSCI Environment Requirements
A. The E085 Experiment Manager shall execute in the environment described in the HRF Workstation 2 Interface Definition Document, LS-71042-14-4A.
B. The E085 Experiment Manager shall utilize a maximum amount of 25 MB of disk space.
C. The E085 Experiment Manager shall utilize a maximum amount of 8 MB of Random Access Memory (RAM).
3.2.7.3.6.5.9 Software Quality Factors
The E085 Experiment Manager executable shall generate consistent results given the same initialization data.
3.2.7.3.6.5.10 Design and Implementation Constraints
The HRF HCI Design Guide (LS-71130) should be considered when designing displays for the E085 Experiment Manager.
User interface software associated with the E085 Experiment Manager will comply with the Display and Graphics Commonality Standards (DGCS) (SSP 50313, ).
3.2.7.3.6.5.11 Precedence and Criticality of Requirements
All requirements are equally weighted and are not listed in any order of precedence or criticality.
3.2.7.3.6.6 E507 Experiment Manager CSCI
The E507 Experiment Manager CSCI is flight software, which resides on the HRF Workstation 2. The software is provided by the Principal Investigator.
The E507 Experiment Manager is launched by the Session Manager. It displays the visual stimuli for the E507 experiment protocols and interacts with the Paddle, the Hand Switch and the tracking hardware on the Head Mounted Display. It instructs the subject on when and how to make responses, and records these responses during the protocol. Upon completion of the protocol, the E507 Experiment Manager returns control to the Session Manager.
3.2.7.3.6.6.1 CSCI Functional and Performance Requirements
Listed below are the functional and performance requirements specific to the E507 Experiment Manager.
A. The E507 Experiment Manager shall be viewable in the left eye and the right eye of the Head Mounted Display.
B. The E507 Experiment Manager shall render the visual images that make up the Upright Grasping, Grasping with Head Tilt, Pointing, Interception, and Tilted Grasping protocols in ground mode.
C. The E507 Experiment Manager shall render the visual images that make up the Upright Grasping, Grasping with Head Tilt, Pointing, and Interception protocols in flight mode.
D. The E507 Experiment Manager shall change the WS2 screen resolution to the appropriate resolution and color depth for the experiment protocol.
E. The E507 Experiment Manager scene shall respond to subject hand movements while the subject is holding the Hand Switch.
F. The E507 Experiment Manager scene shall respond to subject hand movements while the subject is holding the Paddle.
G. The E507 Experiment Manager scene shall respond to subject head movements while the subject is wearing the head mounted display.
H. The E507 Experiment Manager shall log experiment data collected during the current protocol.
3.2.7.3.6.6.2 CSCI External Interface Requirements
Listed below are the external interface software requirements for the E507 Experiment Manager.
The E507 Experiment Manager will interface with the Session Manager. This external interface shall be used to initiate the execution of the E507 Experiment Manager. The interface is defined in the Interface Control Document for the VOILA Session Manager (VSM).
3.2.7.3.6.6.2.1 Word/Byte Notations, Types and Data Transmissions
3.2.7.3.6.6.2.1.1 Word/Byte Notations
The E507 Experiment Manager shall use the word/byte notations as specified in paragraph 3.1.1, Notations in SSP 52050. (LS-71000, Section 6.1.3.1.1)
3.2.7.3.6.6.2.1.2 Data Types
The E507 Experiment Manager shall use the data types as specified in paragraph 3.2.1 and subsections, Data Formats in SSP 52050. (LS-71000, Section 6.1.3.1.2)
3.2.7.3.6.6.2.1.3 Service Requests
The E507 Experiment Manager shall request services in accordance with LS-71062-8, Interface Definition Document for the HRF Common Software (LS-71000, Section 6.1.3.3.1.5).
3.2.7.3.6.6.3 CSCI Internal Interface Requirements
The E507 Experiment Manager internal interfaces are defined by the Principal Investigator.
3.2.7.3.6.6.4 CSCI Internal Data Requirements
The E507 Experiment Manager internal data requirements are defined by the Principal Investigator.
3.2.7.3.6.6.5 CSCI Adaptation Requirements
There are no CSCI adaptation requirements for the E507 Experiment Manager.
3.2.7.3.6.6.6 Software Safety Requirements
The E507 Experiment Manager CSCI shall not be used to hold, store, or process any safety critical parameters or commands.
3.2.7.3.6.6.7 Data Privacy Requirements
There are no CSCI data privacy requirements for the E507 Experiment Manager.
3.2.7.3.6.6.8 CSCI Environment Requirements
A. The E507 Experiment Manager shall execute in the environment described in the HRF Workstation 2 Interface Definition Document, LS-71042-14-4A.
B. The E507 Experiment Manager shall utilize a maximum amount of 25 MB of disk space.
C. The E507 Experiment Manager shall utilize a maximum amount of 8 MB of Random Access Memory (RAM).
3.2.7.3.6.6.9 Software Quality Factors
The E507 Experiment Manager executable shall generate consistent results given the same initialization data.
3.2.7.3.6.6.10 Design and Implementation Constraints
The HRF HCI Design Guide (LS-71130) should be considered when designing displays for the E507 Experiment Manager.
User interface software associated with the E507 Experiment Manager will comply with the Display and Graphics Commonality Standards (DGCS) (SSP 50313, ).
3.2.7.3.6.6.11 Precedence and Criticality of Requirements
All requirements are equally weighted and are not listed in any order of precedence or criticality.
3.2.7.3.7 Reserved
3.2.7.3.8 Reserved
3.2.7.3.9 Reserved
3.2.7.3.10 Medium Rate Data Link
Not applicable to VOILA.
3.2.7.4 Payload National Television Standards Committee (NTSC) Video Interface Requirements
Not applicable to VOILA.
3.2.7.5 Thermal Control Interface Requirements
3.2.7.5.1 HRF Rack Provided Internal Thermal Control System (ITCS) Moderate Temperature Loop (MTL) Interface
Not applicable to VOILA.
3.2.7.5.2 HRF Rack Heat Exchanger to SIR Drawer Interface
HRF racks provide one air-to-fluid heat exchanger at each 4 PU SIR drawer interface. (LS-71000, Section 6.2.5.2)
3.2.7.5.2.1 Reserved
3.2.7.5.2.2 HRF Rack Mounted SIR Drawer Cooling Fans
A. Fan Hardware
SIR drawer instruments mounted in HRF racks shall use a HRF common fan, part number SEG46116060-701, defined in National Aeronautics and Space Administration (NASA)/JSC drawing SEG 46116060. This drawing identifies the fan, mounting information, leadwire length, connector and pinout requirements. (LS-71000, Section 6.2.5.2.2A)
B. Fan Location
The fan shall be located on the inside of the payload drawer in the rear right hand side (as viewed from the front of the rack). (LS-71000, Section 6.2.5.2.2B)
C. Vibration Isolation
The fan shall be mounted with a Vibration Isolation Gasket between the fan and chassis. Reference NASA/JSC drawing SDG 46116118 for an example of an approved vibration absorbing gasket. (LS-71000, Section 6.2.5.2.2C)
D. Fan Mounting
The fan mounting shall be such that the fan can be IVA replaceable. This design is the responsibility of the hardware developer. Reference NASA/JSC drawing SEG 46116120 for an approved IVA replaceable fan design. (LS-71000, Section 6.2.5.2.2D)
E. Fan Operating Voltage
Fans shall operate within a voltage range of 28 +0.5/-2.0 Vdc. (LS-71000, Section 6.2.5.2.2E)
F. Fan Speed Controller
The hardware developer shall control the common fan at the lowest speed required to provide sufficient cooling air (32 (C inlet air temperature) to their instrument. This speed shall be determined by thermal analysis and HRF Systems Engineering and Integration. It is the hardware developer’s responsibility for the design of a fan speed controller if one is deemed necessary. Reference NASA/JSC drawing SEG46115961 for an approved fan speed controller. (LS-71000, Section 6.2.5.2.2F)
NOTE: A fan-to-heat exchanger close-out gasket between the Payload Drawer and the Rack Connector bar will be provided by the rack integrator and installed onto the rack connector bar. (LS-71000, Section 6.2.5.2.2 Note)
3.2.7.6 Vacuum System Requirements
Not applicable to VOILA.
3.2.7.7 Pressurized Gas Interface Requirements
Not applicable to VOILA.
3.2.7.8 Payload Support Services Interfaces Requirements
Not applicable to VOILA.
3.2.7.9 Fire Protection Interface Requirements
NOTE: HRF dependent instruments that have forced air circulation and are mounted in SIR drawer locations within the HRF rack are monitored by the HRF rack smoke detector. The ISS PFE is capable of extinguishing fires within these instrument volumes when discharged into the HRF rack PFE access port. These instruments do not require additional smoke detectors or PFE access ports. (LS-71000, Section 6.2.10)
NOTE: Fire detection requirements for instruments operated outside of the rack have not been defined by ISS. Fire detection methodology for instruments operated outside of rack volumes must be approved by the Program Safety Review Panel (PSRP). Fire suppression requirements in this section apply for instruments operated outside of the rack volume that have forced air flow. (LS-71000, Section 6.2.10)
3.2.7.9.1 Fire Prevention
VOILA shall meet the fire prevention requirements specified in NSTS 1700.7B, ISS Addendum, Paragraph 220.10a. (LS-71000, Section 6.2.10.1)
3.2.7.9.2 Payload Monitoring and Detection Requirements
NOTE: The ISS monitors and detects fire events within payloads containing potential fire sources by using a station approved rack smoke detector. For payload volumes that contain a potential fire source but do not exchange air with the rack smoke detector because there is no forced air circulation, or for metabolic or science isolation purposes, parameter monitoring can be used as an alternative. Use of parameter monitoring will be presented to and approved by the PSRP during the phased safety reviews. Volumes containing no potential fire sources do not require detection capabilities. Small aisle mounted equipment (laptop computers, etc.) may not require detection capabilities. Safety monitoring and detection requirements are specified in NSTS 1700.7B, ISS Addendum, Paragraph 220.10b. (LS-71000, Section 6.1.10.2)
3.2.7.9.2.1 Parameter Monitoring
Not applicable to VOILA.
3.2.7.9.3 Fire Suppression
NOTE: Each separate HRF rack and subrack equipment volume, which contains a potential fire source will require fire suppression capabilities. Determination of potential fire sources will be presented to and approved by the PSRP during the phased safety reviews. Safety fire suppression requirements are specified in NSTS 1700.7B, ISS Addendum, paragraph 220.10c. [SSP 57000E, paragraph 3.10.3]
3.2.7.9.3.1 Portable Fire Extinguisher
Not applicable to VOILA.
3.2.7.9.3.2 Fire Suppression Access Port Accessibility
VOILA shall accommodate the PFE nozzle and bottle specified in Figures 3.2.7.9.3.2-1 and 3.2.7.4.2.2-2 so the PFE nozzle can interface to the PFE port. (LS-71000, Section 6.2.10.3)
[pic]
Figure 3.2.7.9.3.2-1. Manual Fire Suppression Hardware Envelope
[pic]
Figure 3.2.7.9.3.2-2. Closed Volume PFE Nozzle
3.2.7.9.3.3 Fire Suppressant Distribution
The internal layout of VOILA shall allow ISS PFE fire suppressant to be distributed its entire internal volume, lowering the Oxygen concentration to or below 10.5% by volume at any point within the enclosure within one minute. (LS-71000, Section 6.2.10.4)
NOTE: The position of VOILA components near the PFE Access Port should not prevent fire suppressant to be discharged into the volume the PFE Access Port serves. PFE discharge characteristics are specified in Figure 3.2.5.1.5-1 and PFE closed volume nozzle dimensions are specified in Figure 3.2.7.9.3.2-2. (LS-71000, Section 6.2.10.4 Note)
3.2.7.9.4 Labeling
Not applicable to VOILA.
3.2.7.10 Other Interface Requirements
3.2.7.10.1 Lightning
VOILA shall meet the lightning induced environment requirement in paragraph 3.2.8.1 of SSP 30243. (SSP 57000, Section 3.2.4.9)
3.2.7.10.2 Rack Requirements – Pivot Keep Out Zone
VOILA shall comply with the keepout zone for rack pivot mechanism as defined in SSP 41017 Part 1, paragraph 3.2.1.1.2. (SSP 57000, Section 3.1.1.4E)
3.3 Design and Construction
3.3.1 Materials, Processes, and Parts
3.3.1.1 Materials and Processes
3.3.1.1.1 Materials and Parts Use and Selection
VOILA shall use materials and parts that meet the materials requirements specified in NSTS 1700.7B, ISS Addendum, Section 209. (LS-71000, Section 6.2.11.1)
3.3.1.1.1.1 Russian Materials Usage Agreement
A. Materials shall comply with the “Agreement on the Safe Utilization of Materials in Cargos to be Delivered to ISS by Any Vehicle and Transferred to ISS for Stowage and/or Operation” dated 6/22/2000.
B. Fiberglass cloth tape shall not be used in HRF payloads that may be carried into the ISS Russian segment. (Materials and Processes Technology Branch)
3.3.1.1.2 Commercial Parts
Commercial off the Shelf (COTS) parts used in VOILA shall meet the materials requirements specified in NSTS 1700.7B, ISS Addendum, Section 209. (LS-71000, Section 6.2.11.2)
3.3.1.1.3 Fluids
Not applicable to VOILA.
3.3.1.1.4 Cleanliness
VOILA shall conform to Visibly Clean - Sensitive (VC-S) requirements as specified in SN-C-0005. (LS-71000, Section 6.2.11.4)
3.3.1.1.5 Fungus Resistant Material
HRF rack dependent instruments that are intended to remain on-orbit for more than one year shall use fungus resistant materials according to the requirements specified in SSP 30233, Paragraph 4.2.10. (LS-71000, Section 6.2.11.5)
3.3.1.2 Sharp Edges and Corner Protection
VOILA design shall protect crewmembers from sharp edges and corners during all crew operations in accordance with NSTS 1700.7, ISS Addendum, Paragraph 222.1. (LS-71000, Section 6.4.9.2)
3.3.1.3 Holes
Holes that are round or slotted in the range of 10.0 to 25.0 mm (0.4 to 1.0 in) shall be covered. (LS-71000, Section 6.4.9.3)
3.3.1.4 Latches
Latches that pivot, retract, or flex so that a gap of less than 35 mm (1.4 in) exists shall be designed to prevent entrapment of a crewmember’s appendage. (LS-71000, Section 6.4.9.4)
3.3.1.5 Screws and Bolts
Threaded ends of screws and bolts accessible by the crew and extending more than 3.0 mm (0.12 in) shall be capped to protect against sharp threads. (LS-71000, Section 6.4.9.5)
3.3.1.6 Securing Pins
Securing pins shall be designed to prevent their inadvertently backing out above the handhold surface. (LS-71000, Section 6.4.9.6)
3.3.1.7 Levers, Cranks, Hooks and Controls
Levers, cranks, hooks and controls shall not be located where they can pinch, snag, or cut the crewmembers or their clothing. (LS-71000, Section 6.4.9.7)
3.3.1.8 Burrs
Exposed surfaces shall be free of burrs. (LS-71000, Section 6.4.9.8)
3.3.1.9 Locking Wires
A. Not applicable to VOILA.
B. Not applicable to VOILA.
C. Safety wire shall not be used on any on-orbit fasteners. [Payload Safety Review Panel]
3.3.2 Nameplates and Product Marking
3.3.2.1 Equipment Identification
Integrated racks, all (installed in the rack or separately) sub-rack elements, loose equipment, stowage trays, consumables, ORUs, crew accessible connectors and cables, switches, indicators, and controls shall be labeled. Labels are markings of any form [including Inventory Management System (IMS) bar codes] such as decals and placards, which can be adhered, “silk screened,” engraved, or otherwise applied directly onto the hardware. Appendix C of SSP 57000 provides instructions for label and decal design and approval. (LS-71000, Section 6.4.7)
3.3.3 Workmanship
A. Workmanship for VOILA hardware developments at JSC shall be in accordance with approved NASA and industry recognized standards. (LS-71000, Section 7.3.1)
B. Workmanship for VOILA hardware developments at MIT shall be implemented in accordance with the following contract:. (LS-71000, Section 7.3.1)
3.3.4 Interchangeability
3.3.5 Safety Requirements
3.3.5.1 Electrical Safety
HRF rack dependent instruments shall meet the electrical safety requirements as defined in NSTS 1700.7B, ISS Addendum. (LS-71000, Section 6.2.2.14)
3.3.5.1.1 Safety-Critical Circuits Redundancy
Not applicable to VOILA.
3.3.5.1.2 EMI Susceptibility for Safety-Critical Circuits
Not applicable to VOILA.
3.3.5.1.3 Mating/Demating of Powered Connectors
A. VOILA shall comply with the requirements for mating/demating of powered connectors specified in NSTS 18798, MA2-97-093. (LS-71000, Section 6.2.2.14.1.1)
B. VOILA shall comply with the requirements for mating/demating of powered connectors specified in NSTS 18798, MA2-99-170. (Note: Compliance with MA2-99-170 is currently required by the PSRP, but SSP 57000 has not been updated to reflect this change.)
NOTE: The HRF rack or UOP can provide one verifiable upstream inhibit which removes voltage from the UIP and UOP connectors. The module design will provide the verification of the inhibit status at the time the inhibit is inserted. (Derived from LS-71000, Section 6.2.2.14.1.1)
3.3.5.1.4 Power Switches/Controls
Not applicable to VOILA.
3.3.5.1.5 Ground Fault Circuit Interrupters/Portable Equipment DC Sourcing Voltage
Not applicable to VOILA.
3.3.5.1.6 Portable Equipment/Power Cords
A. Non-battery powered portable equipment shall incorporate a three-wire power cord. A three wire power cord consists of a (+) supply lead, a (-) return lead and a safety (green) wire; one end of the safety (green) wire is connected to the portable VOILA chassis (and all exposed conductive surfaces) and the other end is connected to structure of the utility outlet (Payload provided outlet, UOP device, etc.) or through the GFCI interface if GFCI is used. A system of double insulation or its equivalent, when approved by NASA, may be used without a ground wire. (LS-71000, Section 6.2.2.17A)
B. Not applicable to VOILA.
NOTE: The SUP power outlet in the APM does not provide AC protection. (LS-71000, Section 6.2.2.17)
3.3.6 Human Engineering
3.3.6.1 Closures or Covers Design Requirements
Closures or covers shall be provided for any area of the payload that is not designed for routine cleaning. (LS-71000, Section 6.4.3.1.1)
3.3.6.2 Interior Color
3.3.6.2.1 Rack Mounted Equipment
A. SSP 50008, Rev. A, page 3-4, Table 3.2.7.1, applies to HRF rack mounted hardware. Front panels for active and stowage drawers meant for installation in HRF racks shall be off-white, specification #27722 as given in FED-STD-595B, “Federal Standard Colors Used in Government Procurement.” (LS-71000, Section 6.4.3.5.1)
B. The finish shall be semi-gloss. (LS-71000, Section 6.4.3.5.1)
C. SIR drawer panel handle latches are not subject to requirements 3.3.6.2.1 A and B and shall be finished in accordance with the engineering drawings for the panel handle latches. (LS-71000, Section 6.4.3.5.1)
3.3.6.2.2 Stowed/Deployable Equipment
The colors and finishes for stowed and deployable equipment, even if it is normally attached to the rack during use shall be as specified below:
A. COTS equipment that is not repackaged by HRF engineers shall be finished as delivered by the manufacturer. (LS-71000, Section 6.4.3.5.2A)
B. Items that are repackaged by HRF engineers shall be finished using anodic film per MIL-A-8625, Type II, Class 2, Dyed Turquoise. Reference FED-STD-595, Color Specification 15187. (LS-71000, Section 6.4.3.5.2B)
3.3.6.2.3 Colors for Soft Goods
Human factors engineering will provide guidance in the appropriate colors for soft goods, in cooperation with the lead engineers, who will provide data on the available color choices for the specified materials. (LS-71000, Section 6.4.3.5.3)
3.3.6.3 Full Size Range Accommodation
All payload workstations and hardware having crew nominal operations and planned maintenance shall be sized to meet the functional reach limits for the 5th percentile Japanese female and yet shall not constrict or confine the body envelope for the 95th percentile American male as specified in SSP 50005, Section 3. (LS-71000, Section 6.4.2.3)
3.3.6.4 Operation and Control of Payload Equipment
A. Grip Strength
To remove, replace and operate payload hardware, grip strength required shall be less than 254 N (57 lbf). (LS-71000, Section 6.4.1.1A)
B. Linear Forces
Linear forces required to operate or control payload hardware or equipment shall be less than the strength values for the 5th percentile female, defined as 50% of the strength values shown in Figure 3.3.6.4-1 and 60% of the strength values shown in Figure 3.3.6.4-2. (LS-71000, Section 6.4.1.1B)
C. Torque
Torque required to operate or control payload hardware or equipment shall be less than the strength values for the 5th percentile female, defined as 60% of the calculated 5th percentile male capability shown in Figure 3.3.6.4-3. (LS-71000, Section 6.4.1.1C)
[pic]
|Arm Strength (N) |
|(1) |(2) |(3) |(4) |(5) |(6) |(7) |
|Degree of elbow |Pull |Push |Up |Down |In |Out |
|flexion (rad) |
| |(8) |(9) |(10) |
| |Hand Grip | | |
| |L |R |Thumb-finger grip (Palmer) |Thumb-finger grip (tips) |
|Momentary hold |250 |260 |60 |60 |
|Sustained hold |145 |155 |35 |35 |
| *Elbow angle shown in radians |
|**L = Left, R = Right |
|Arm strength (lb) |
|(1) |(2) |(3) |(4) |(5) |(6) |(7) |
|Degree of elbow |Pull |Push |Up |Down |In |Out |
|flexion (deg) |
| |(8) |(9) |(10) |
| |Hand Grip | | |
| |L |R |Thumb-finger grip (Palmer) |Thumb-finger grip (tips) |
|Momentary hold |56 |59 |13 |13 |
|Sustained hold |33 |35 |8 |8 |
|*Left; R = Right |
Figure 3.3.6.4-1. Arm, Hand and Thumb/Finger Strength (5th Percentile Male Data)
[pic]
Figure 3.3.6.4-2. Leg Strength at Various Knee and Thigh Angles (5th Percentile Male Data)
[pic]
Figure 3.3.6.4-3. Torque Strength
3.3.6.5 Maintenance Operations
Not applicable to VOILA.
3.3.6.6 Adequate Clearance
The payloads shall provide clearance for the crew to perform installation, operations and maintenance tasks, including clearance for hand access, tools and equipment used in these tasks. (LS-71000, Section 6.4.2.1)
3.3.6.7 Accessibility
A. Payload hardware shall be geometrically arranged to provide physical and visual access for all payload installation, operations, and maintenance tasks. Payload ORUs should be removable along a straight path until they have cleared the surrounding structure. (LS-71000, Section 6.4.2.2A)
B. IVA clearances for finger access shall be provided as given in Figure 3.3.6.7-1. (LS-71000, Section 6.4.2.2B)
|Minimal finger-access to first joint |
|Push button access: Bare hand: 32 mm dia (1.26 in.) |[pic] |
|Thermal gloved hand: 38 mm dia (1.5 in.) | |
|Two finger twist access: Bare hand: object plus 50 mm (1.97 in.) | |
|Thermal gloved hand: object plus 65 mm (2.56 in.) | |
Figure 3.3.6.7-1. Minimum Sizes for Access Openings for Fingers
3.3.6.8 One-Handed Operation
Cleaning equipment and supplies shall be designed for one-handed operation or use. (LS-71000, Section 6.4.3.1.3)
3.3.6.9 Continuous/Incidental Contact - High Temperature
When payload surfaces whose temperature exceeds 49 °C (120 °F), which are subject to continuous or incidental contact, are exposed to crewmember’s bare skin contact, protective equipment shall be provided to the crew and warning labels shall be provided at the surface site. This also applies to surfaces not normally exposed to the cabin in accordance with the NASA IVA Touch Temperature Safety interpretation letter JSC, MA2-95-048. (LS-71000, Section 6.4.3.2.1)
3.3.6.10 Continuous/Incidental Contact - Low Temperature
Not applicable to VOILA.
3.3.6.11 Equipment Mounting
Equipment items used during nominal operations and planned maintenance shall be designed, labeled, or marked to protect against improper installation. (LS-71000, Section 6.4.4.2.1)
3.3.6.12 Drawers and Hinged Panels
Not applicable to VOILA.
3.3.6.13 Alignment
Payload hardware having blind mate connectors shall provide guide pins or their equivalent to assist in alignment of hardware during installation. (LS-71000, Section 6.4.4.2.3)
3.3.6.14 Slide-Out Stops
Limit stops shall be provided on slide or pivot mounted sub-rack hardware, which is required to be pulled out of its installed positions. (LS-71000, Section 6.4.4.2.4)
3.3.6.15 Push-Pull Force
Payload hardware mounted into a capture-type receptacle that requires a push-pull action shall require a force less than 156 N (35 lbf) to install or remove. (LS-71000, Section 6.4.4.2.5)
3.3.6.16 Covers
Where physical access is required, one of the following practices shall be followed, with the order of preference given.
A. Provide a sliding or hinged cap or door where debris, moisture, or other foreign materials might otherwise create a problem. (LS-71000, Section 6.4.4.2.6.1A)
B. Provide a quick-opening cover plate if a cap will not meet stress requirements. (LS-71000, Section 6.4.4.2.6.1B)
3.3.6.17 Self-Supporting Covers
All access covers that are not completely removable shall be self-supporting in the open position. (LS-71000, Section 6.4.4.2.6.2)
3.3.6.18 Accessibility
It shall be possible to mate/demate individual connectors without having to remove or mate/demate other connectors during nominal operations. (LS-71000, Section 6.4.4.3.2A)
3.3.6.19 Ease of Disconnect
A. Electrical connectors, which are mated/demated during nominal operations shall require no more than two turns to disconnect. (LS-71000, Section 6.4.4.3.3A)
B. Not applicable to VOILA.
3.3.6.20 Indication of Pressure/Flow
Not applicable to VOILA.
3.3.6.21 Self Locking
Payload electrical connectors shall provide a self-locking feature. (LS-71000, Section 6.4.4.3.5)
3.3.6.22 Connector Arrangement
A. Space between connectors and adjacent obstructions shall be a minimum of 25 mm (1 inch) for IVA access. (LS-71000, Section 6.4.4.3.6A)
B. Connectors in a single row or staggered rows which are removed sequentially by the crew IVA shall provide 25 mm (1 inch) of clearance from other connectors and/or adjacent obstructions for 270 degrees of sweep around each connector beginning at the start of its removal/replacement sequence. (LS-71000, Section 6.4.4.3.6B)
3.3.6.23 Arc Containment
Electrical connector plugs shall be designed to confine/isolate the mate/demate electrical arcs or sparks. (LS-71000, Section 6.4.4.3.7)
3.3.6.24 Connector Protection
Protection shall be provided for all demated connectors against physical damage and contamination. (LS-71000, Section 6.4.4.3.8)
3.3.6.25 Connector Shape
Payload connectors shall use different connector shapes, sizes or keying to prevent mating connectors when lines differ in content. (LS-71000, Section 6.4.4.3.9)
3.3.6.26 Fluid and Gas Line Connectors
Not applicable to VOILA.
3.3.6.27 Alignment Marks or Guide Pins
Mating parts shall have alignment marks in a visible location during mating or guide pins (or their equivalent). (LS-71000, Section 6.4.4.3.11A)
3.3.6.28 Coding
A. Both halves of mating connectors shall display a code or identifier, which is unique to that connection. (LS-71000, Section 6.4.4.3.12A)
B. The labels or codes on connectors shall be located so they are visible when connected or disconnected. (LS-71000, Section 6.4.4.3.12B)
3.3.6.29 Pin Identification
Each pin shall be uniquely identifiable in each electrical plug and each electrical receptacle. At least every 10th pin must be labeled. (LS-71000, Section 6.4.4.3.13)
3.3.6.30 Orientation
Grouped plugs and receptacles shall be oriented so that the aligning pins or equivalent devices are in the same relative position. (LS-71000, Section 6.4.4.3.14)
3.3.6.31 Hose/Cable Restraints
A. Not applicable to VOILA.
B. Conductors, bundles, or cables shall be secured by means of clamps unless they are contained in wiring ducts or cable retractors. (LS-71000, Section 6.4.4.3.15B)
C. Cables should be bundled if multiple cables are running in the same direction and the bundling does not cause EMI. (LS-71000, Section 6.4.4.3.15C)
D. Loose cables (longer than 0.33 meters (1 foot) shall be restrained as follows (LS-71000, Section 6.4.4.3.15D):
|Length (m) |Restraint Pattern (% of length) tolerances +/- 10%) |
|0.33-1.00 |50 |
|1.00-2.00 |33,67 |
|2.00-3.00 |20, 40, 60, 80 |
|>3.00 |at least each 0.5 meters |
3.3.6.32 Non-Threaded Fasteners Status Indication
An indication of correct engagement (hooking, latch fastening, or proper positioning of interfacing parts) of non-threaded fasteners shall be provided. (LS-71000, Section 6.4.4.4.1)
3.3.6.33 Mounting Bolt/Fastener Spacing
Clearance around fasteners to permit fastener hand threading (if necessary) shall be a minimum of 0.5 inches for the entire circumference of the bolt head and a minimum of 1.5 inches over 180 degrees of the bolt head and provide the tool handle sweep as seen in Figure 3.3.6.33-1. Excepted are National Space Transportation System (NSTS) standard middeck lockers or payload-provided hardware with the static envelope dimensions (cross-section) as specified in Figures 3.4.2.1-1, 3.4.2.2-1 and 3.4.2.3-1 of NSTS-21000-IDD-MDK and other similar captive fastener arrangements. (LS-71000, Section 6.4.4.4.2)
3.3.6.34 Multiple Fasteners
When several fasteners are used on one item they shall be of identical type. (LS-71000, Section 6.4.4.4.3)
NOTE: Phillips or Torque-Set fasteners may be used where fastener installation is permanent relative to planned on-orbit operations or maintenance, or where tool-fastener interface failure can be corrected by replacement of the unit containing the affected fastener with a spare unit. (LS-71000, Section 6.4.4.4.3)
3.3.6.35 Captive Fasteners
All fasteners planned to be installed and/or removed on-orbit shall be captive when disengaged. (LS-71000, Section 6.4.4.4.4)
3.3.6.36 Quick Release Fasteners
A. Quick release fasteners shall require a maximum of one complete turn to operate (quarter - turn fasteners are preferred). (LS-71000, Section 6.4.4.4.5A)
B. Quick release fasteners shall be positive locking in open and closed positions. (LS-71000, Section 6.4.4.4.5B)
3.3.6.37 Threaded Fasteners
Only right handed threads shall be used. (LS-71000, Section 6.4.4.4.6)
3.3.6.38 Over Center Latches
Not applicable to VOILA.
|Opening dimensions |Task |
|[pic] |A 117 mm (4.6 in) |Using common screwdriver with freedom to turn |
| |B 107 mm (4.2 in) |hand through 180( |
|[pic] |A 133 mm (5.2 in) |Using pliers and similar tools |
| |B 115 mm (4.5 in) | |
|[pic] |A 155 mm (6.1 in) |Using T-handle wrench with freedom to turn |
| |B 135 mm (5.3 in) |wrench through 180( |
|[pic] |A 203 mm (8.0 in) |Using open-end wrench with freedom to turn |
| |B 135 mm (5.3 in) |wrench through 62( |
|[pic] |A 122 mm (4.8 in) |Using Allen-type wrench with freedom to turn |
| |B 155 mm (6.1 in) |wrench through 62( |
Figure 3.3.6.33-1. Minimal Clearance for Tool-Operated Fasteners
3.3.6.39 Winghead Fasteners
Not applicable to VOILA.
3.3.6.40 Fastener Head Type
A. Hex type external or internal grip or combination head fasteners shall be used where on-orbit crew actuation is planned, e.g., ORU replacement. (LS-71000, Section 6.4.4.4.9A)
B. If a smooth surface is required, flush or oval head internal hex grip fasteners shall be used for fastening. (LS-71000, Section 6.4.4.4.9B)
C. Slotted fasteners shall not be used to carry launch loads for hard-mounted equipment. Slotted fasteners are allowed in non-structural applications (e.g., computer data connectors, stowed commercial equipment). (LS-71000, Section 6.4.4.4.9C)
3.3.6.41 One-Handed Actuation
Fasteners planned to be removed or installed on-orbit shall be designed and placed so they can be mated/demated using either hand. (LS-71000, Section 6.4.4.4.10)
3.3.6.42 DELETED
3.3.6.43 Access Holes
Covers or shields through which mounting fasteners must pass for attachment to the basic chassis of the unit shall have holes for passage of the fastener without precise alignment (and hand or necessary tool if either is required to replace). (LS-71000, Section 6.4.4.4.12)
3.3.6.44 Controls Spacing Design Requirements
All spacing between controls and adjacent obstructions shall meet the minimum requirements as shown in Figure 3.3.6.44-1, Control Spacing Requirements for Ungloved Operation. (LS-71000, Section 6.4.5.1)
3.3.6.45 Accidental Activation
Requirements for reducing accidental actuation of controls are defined as follows:
[pic]
Figure 3.3.6.44-1. Control Spacing Requirements for Ungloved Operation
3.3.6.45.1 Protective Methods
Payloads shall provide protection against accidental control actuation using one or more of the protective methods listed in sub-paragraphs A through G below. Infrequently used controls (i.e., those used for calibration) should be separated from frequently used controls. Leverlock switches or switch covers are strongly recommended for switches related to mission success. Switch guards may not be sufficient to prevent accidental actuation. (LS-71000, Section 6.4.5.2.1)
NOTE: Displays and controls used only for maintenance and adjustments, which could disrupt normal operations if activated, should be protected during normal operations, e.g., by being located separately or guarded/covered.
A. Locate and orient the controls so that the operator is not likely to strike or move them accidentally in the normal sequence of control movements. (LS-71000, Section 6.4.5.2.1A)
B. Recess, shield, or otherwise surround the controls by physical barriers. The control shall be entirely contained within the envelope described by the recess or barrier. (LS-71000, Section 6.4.5.2.1B)
C. Cover or guard the controls. Safety or lock wire shall not be used. (LS-71000, Section 6.4.5.2.1C)
D. Cover guards when open shall not cover or obscure the protected control or adjacent controls. (LS-71000, Section 6.4.5.2.1D)
E. Provide the controls with interlocks so that extra movement (e.g., lifting switch out of a locked detent position) or the prior operation of a related or locking control is required. (LS-71000, Section 6.4.5.2.1E)
F. Provide the controls with resistance (i.e., viscous or coulomb friction, spring-loading, or inertia) so that definite or sustained effort is required for actuation. (LS-71000, Section 6.4.5.2.1F)
F. Provide the controls with a lock to prevent the control from passing through a position without delay when strict sequential actuation is necessary (i.e., the control moved only to the next position, then delayed). (LS-71000, Section 6.4.5.2.1G)
3.3.6.45.2 Noninterference
Payload provided protective devices shall not cover or obscure other displays or controls. (LS-71000, Section 6.4.5.2.2)
3.3.6.45.3 Dead-Man Controls
Dead-man controls are covered under NSTS 1700.7B, ISS Addendum Paragraphs 200.4a and 303.2. (LS-71000, Section 6.4.5.2.3)
3.3.6.45.4 Barrier Guards
Barrier guard spacing shall adhere to the requirements for use with the toggle switches, rotary switches, and thumbwheels as shown in Figures 3.3.6.44-1, Control Spacing Requirements for Ungloved Operation and 3.3.6.45.4-1, Rotary Switch Guard. (LS-71000, Section 6.4.5.2.4)
[pic]
Figure 3.3.6.45.4-1. Rotary Switch Guard
3.3.6.45.5 Recessed Switch Protection
Not applicable to VOILA.
3.3.6.46 Position Indication
When payload switch protective covers are used, control position shall be evident without requiring cover removal. (LS-71000, Section 6.4.5.2.7)
3.3.6.47 Hidden Controls
Not applicable to VOILA.
3.3.6.48 Hand Controllers
Hand controllers, excluding trackballs and mice, shall have a separate on/off control to prevent inadvertent actuation when the controller is not in use. (LS-71000, Section 6.4.5.2.9)
3.3.6.49 Valve Controls
Not applicable to VOILA.
3.3.6.50 Toggle Switches
Dimensions for a standard toggle switch shall conform to the values presented in Figure 3.3.6.50-1, Toggle Switches. (LS-71000, Section 6.4.5.4)
[pic]
| |Dimensions |Resistance |
| |L |D |Small |Large |
| |Arm Length |Control Tip |Switch |Switch |
|Minimum |13 mm |3 mm |2.8 N |2.8 N |
| |(1/2 in.) |(1/8 in.) |(10 oz) |(10 oz.) |
|Maximum |50 mm |25 mm |4.5 N |11 N |
| |(2 in.) |(1 in.) |(16 oz.) |(40 oz.) |
| |Displacement between positions |
| |A |
| |2 position |3 position |
|Minimum |30( |17( |
|Maximum |80( |40( |
|Desired | |25( |
| |Separation |
| |Single finger |S | |
| |operation |Single finger sequential operation |Simultaneous operation |
| | | |by different fingers |
| | |† | | |
|Minimum |19 mm |25 mm |13 mm |16 mm |
| |(3/4 in.) |(1 in.) |(1/2 in.) |(5/8 in.) |
|Optimum |50 mm |50 mm |25 mm |19 mm |
| |(2 in.) |(2 in.) |(1 in.) |(3/4 in.) |
|† Using a lever lock toggle switch |
Figure 3.3.6.50-1. Toggle Switches
3.3.6.51 Restraints and Mobility Aids
Payloads shall be designed such that all installation, operation and maintenance can be performed using standard crew restraints, mobility aids and interfaces as defined in SSP 30257:004. (LS-71000, Section 6.4.6)
3.3.6.51.1 Stowage Drawer Contents Restraints
Not applicable to VOILA.
3.3.6.51.2 Stowage and Equipment Drawers/Trays
Not applicable to VOILA.
3.3.6.51.3 Captive Parts
Payloads and payload equipment shall be designed in such a manner to ensure that all unrestrained parts (e.g., locking pins, knobs, handles, lens covers, access plates, or similar devices) that may be temporarily removed on orbit will be tethered or otherwise held captive. (LS-71000, Section 6.4.6.3)
3.3.6.51.4 Handle and Grasp Area Design Requirements
3.3.6.51.4.1 Handles and Restraints
All removable or portable items, which cannot be grasped with one hand, as per Table 3.3.6.51.4.1-1 [TBD, referenced table is not included in SSP 57000], shall be provided with handles or other suitable means of grasping, tethering, carrying and restraining. (LS-71000, Section 6.4.6.4.1)
3.3.6.51.4.2 Handle Location/Front Access
Handles and grasp areas shall be placed on the accessible surface of a payload item consistent with the removal direction. (LS-71000, Section 6.4.6.4.2)
3.3.6.51.4.3 Handle Dimensions
IVA handles for movable or portable units shall be designed in accordance with the minimum applicable dimensions in Figure 3.3.6.51.4.3-1. (LS-71000, Section 6.4.6.4.3)
3.3.6.51.4.4 Non-Fixed Handles Design Requirements
Not applicable to VOILA.
3.3.6.52 Electrical Hazards
Electrical equipment other than bioinstrumentation equipment will incorporate the following controls as specified below:
A. If the exposure condition is below the threshold for shock (i.e., below maximum leakage current and voltage requirements as defined within this section), no controls are required. Non-patient equipment with internal voltages not exceeding 30 volts rms or DC nominal (32 volts rms or DC maximum) will contain potentials below the threshold for electrical shock. (LS-71000, Section 6.4.9.1A)
B. If the exposure condition exceeds the threshold for shock, but is below the threshold of the let-go current profile (critical hazard) as defined in Table 3.3.6.52-1, two independent controls (e.g., a safety (green) wire, bonding, insulation, leakage current levels below maximum requirements) shall be provided such that no single failure, event, or environment can eliminate more than one control. (LS-71000, Section 6.4.9.1B)
| | |Dimensions in mm (in inches) |
|Illustration |Type of handle |(Bare hand) |
| | |X |Y |Z |
|[pic] | | | | |
| |Two-finger bar |32 |65 |75 |
| | |(1-1/4) |(2-1/2) |(3) |
| |One-hand bar |48 |111 |75 |
| | |(1-7/8) |(4-3/8) |(3) |
| |Two-hand bar |48 |215 |75 |
| | |(1-7/8) |(8-1/2) |(3) |
|[pic] | | | | |
| |T-bar |38 |100 |75 |
| | |(1-1/2) |(4) |(3) |
|[pic] | | | | |
| |J-bar |50 |100 |75 |
| | |(2) |(4) |(3) |
|[pic] | | | | |
| |Two-finger recess |32 |65 |75 |
| | |(1-1/4) |(2-1/2) |(3) |
| |One-hand recess |50 |110 |90 |
| | |(2) |(4-1/4) |(3-1/2) |
|[pic] | | | | |
| |Finger-tip recess |19 |— |13 |
| | |(3/4) | |(1/2) |
| |On-finger recess |32 |— |50 |
| | |(1-1/4) | |(2) |
|Curvature of handle Weight of item Minimum Diameter |
|or edge |
|(DOES NOT up to 6.8 kg (up to 15 lbs) D = 6 mm (1/4 in) Gripping efficiency is best |
|PRECLUDE 6.8 to 9.0 kg (15 to 20 lbs) D = 13 mm (1/2 in) if finger can curl around |
|USE OF OVAL 9.0 to 18 kg (20 to 40 lbs) D = 19 mm (3/4 in) handle or edge to any angle |
|HANDLES) Over 18 kg (over 40 lbs) D = 25 mm (1 in) of 2/3 π rad (120() or more |
|T-bar post T = 13 mm (1/2 in) |
Figure 3.3.6.51.4.3-1. Minimum IVA Handle Dimensions for IVA Applications
C. If the exposure condition exceeds both the threshold for shock and the threshold of the let-go current profile (catastrophic hazardous events) as defined in Table 3.3.6.52-1, three independent controls shall be provided such that no combination of two failures, events or environments can eliminate more than two controls. (LS-71000, Section 6.4.9.1C)
TABLE 3.3.6.52-1. LET-GO CURRENT PROFILE,
THRESHOLD VERSUS FREQUENCY
|FREQUENCY |MAXIMUM TOTAL PEAK CURRENT |
|(HERTZ) |(AC + DC COMPONENTS COMBINED) MILLIAMPERES |
|DC |40.0 |
|15 |8.5 |
|2000 |8.5 |
|3000 |13.5 |
|4000 |15.0 |
|5000 |16.5 |
|6000 |17.9 |
|7000 |19.4 |
|8000 |20.9 |
|9000 |22.5 |
|10000 |24.3 |
|50000 |24.3 |
|(BASED ON 99.5 PERCENTILE RANK OF ADULTS) |
D. If two dependent controls are provided, the physiological effect that a crew member experiences as a result of the combinations of the highest internal voltage applied to or generated within the equipment and the frequency and wave form associated with a worst case credible failure shall be below the threshold of the let-go current profile as defined in Table 3.3.6.52-1. (LS-71000, Section 6.4.9.1D)
E. If it cannot be demonstrated that the hazard meets the conditions of Paragraph A, B or C above, three independent hazard controls shall be provided such that no combination of two failures, events or environments can eliminate more than two controls. (LS-71000, Section 6.4.9.1E)
3.3.6.52.1 Mismatched
A. The design of electrical connectors shall make it impossible to inadvertently reverse a connection or mate the wrong connectors if a hazardous condition can be created. (LS-71000, Section 6.4.9.1.1A)
B. Payload and on-orbit support equipment, wire harnesses, and connectors shall be designed such that no blind connections or disconnections must be made during payload installation, operation, removal, or maintenance on orbit unless the design includes scoop proof connectors or other protective features (NSTS 1700.7B, ISS Addendum, Paragraph 221). (LS-71000, Section 6.4.9.1.1B)
C. For payload equipment, for which mismating or cross-connection may damage ISS-provided equipment, plugs, and receptacles (connectors), shall be selected and applied such that they cannot be mismatched or cross-connected in the intended system as well as adjacent systems. Although identification markings or labels are required, the use of identification alone is not sufficient to preclude mismating. (LS-71000, Section 6.4.9.1.1C)
D. For all other payload connections, combinations of identification, keying and clocking, and equipment test and checkout procedures shall be employed at the payload’s discretion to minimize equipment risk while maximizing on-orbit operability. (LS-71000, Section 6.4.9.1.1D)
3.3.6.52.2 Overload Protection
3.3.6.52.2.1 Device Accessibility
An overload protective device shall not be accessible without opening a door or cover, except that an operating handle or operating button of a circuit breaker, the cap of an extractor-type fuse holder, and similar parts may project outside the enclosure. (LS-71000, Section 6.4.9.1.2.1)
3.3.6.52.2.2 Extractor -Type Fuse Holder
Not applicable to VOILA.
3.3.6.52.2.3 Overload Protection Location
Overload protection (fuses and circuit breakers) intended to be manually replaced or physically reset on-orbit shall be located where they can be seen and replaced or reset without removing other components. (LS-71000, Section 6.4.9.1.2.3)
3.3.6.52.2.4 Overload Protection Identification
Not applicable to VOILA.
3.3.6.52.2.5 Automatic Restart Protection
Controls shall be employed that prevent automatic restarting after an overload-initiated shutdown. (LS-71000, Section 6.4.9.1.2.5)
3.3.6.53 Audio Devices (Displays)
Not applicable to VOILA.
3.3.6.54 Egress
All payload egress requirements shall be in accordance with NSTS 1700.7B, ISS Addendum, Paragraph 205. (LS-71000, Section 6.4.9.11)
3.3.7 System Security
3.3.8 Design Requirements
3.3.8.1 Structural Design Requirements
3.3.8.1.1 On-orbit Loads
A. VOILA shall provide positive margins of safety for on-orbit loads of 0.2 Gs acting in any direction. (LS-71000, Section 6.2.1.1.4A)
B Crew Induced Load Requirements
VOILA shall provide positive margins of safety when exposed to the crew induced loads defined in Table 3.3.8.1.1-1, Crew-Induced Loads. (LS-71000, Section 6.2.1.1.4B)
TABLE 3.3.8.1.1-1. CREW-INDUCED LOADS
|CREW SYSTEM OR STRUCTURE | | |DIRECTION OF LOAD |
| |TYPE OF LOAD |LOAD | |
|LEVERS, HANDLES, OPERATING |PUSH OR PULL CONCENTRATED ON |222.6 N (50 LBF), LIMIT |ANY DIRECTION |
|WHEELS, CONTROLS |MOST EXTREME EDGE | | |
|SMALL KNOBS |TWIST (TORSION) |14.9 N-M (11 FT-LBF), LIMIT |EITHER DIRECTION |
|EXPOSED UTILITY LINES |PUSH OR PULL |222.6 N (50 LBF) |ANY DIRECTION |
|(GAS, FLUID, AND VACUUM) | | | |
|RACK FRONT PANELS AND ANY |LOAD DISTRIBUTED OVER A 4 INCH|556.4 N (125 LBF), LIMIT |ANY DIRECTION |
|OTHER NORMALLY EXPOSED |BY 4 INCH AREA | | |
|EQUIPMENT | | | |
|LEGEND: |
|FT = FEET, M = METER, N = NEWTON, LBF = POUNDS FORCE |
3.3.8.1.2 Safety Critical Structures Requirements
VOILA shall be designed in accordance with the requirements specified in SSP 52005. (LS-71000, Section 6.2.1.1.1)
3.3.8.1.3 First Modal Frequency
SIR drawer instruments shall have a first modal frequency of not less than 35 Hz for launch and landing, based on rigidly mounting the instrument at the rack to SIR drawer instrument interface. (LS-71000, Section 6.2.1.1.2)
3.3.8.1.4 Launch and Landing Loads
A. For design and qualification purposes, SIR drawer instruments shall maintain positive margins of safety for the MPLM ascent random vibration environment as defined in Table 3.3.8.1.4-1, “Random Vibration Criteria for HRF Rack Post Mounted Equipment Weighing 100 Pounds or Less in the MPLM”, or Table 3.3.8.1.4-2, “Random Vibration Criteria for HRF Rack Post Mounted Equipment Weighing More Than 100 Pounds in the MPLM.” (LS-71000, Section 6.2.1.1.3A)
Note: This requirement is only applicable to the VOILA drawer.
B. SIR drawer instruments shall maintain positive margins of safety for the launch and landing conditions in the MPLM. For early design, the acceleration environment defined in Table 3.3.8.1.4-3, “HRF Rack Mounted Equipment Load Factors (Equipment Frequency 35 Hz)” will be used. These load factors will be superseded by load factors obtained through ISS-performed Coupled Loads Analysis as described in SSP 52005. (LS-71000, Section 6.2.1.1.3B)
TABLE 3.3.8.1.4-1. RANDOM VIBRATION CRITERIA FOR HRF RACK POST MOUNTED
EQUIPMENT WEIGHING 100 POUNDS OR LESS IN THE MPLM
|FREQUENCY |LEVEL |
| 20 HZ |0.005 G2/HZ |
| 20-70 HZ |+5.0 DB/OCT. |
| 70-200 HZ |0.04 G2/HZ |
| 200-2000 HZ |-3.9 DB/OCT. |
| 2000 HZ |0.002 G2/HZ |
| | |
|COMPOSITE |4.4 GRMS |
NOTE: CRITERIA IS THE SAME FOR ALL DIRECTIONS (X, Y, Z)
TABLE 3.3.8.1.4-2. RANDOM VIBRATION CRITERIA FOR HRF RACK POST MOUNTED
EQUIPMENT WEIGHING MORE THAN 100 POUNDS IN THE MPLM
|FREQUENCY |LEVEL |
| 20 HZ |0.002 G2/HZ |
| 20-70 HZ |+4.8 DB/OCT. |
| 70-150 HZ |0.015 G2/HZ |
| 150-2000 HZ |-3.7 DB/OCT. |
| 2000 HZ |0.0006 G2/HZ |
| | |
|COMPOSITE |2.4 GRMS |
NOTE: CRITERIA IS THE SAME FOR ALL DIRECTIONS (X, Y, Z)
TABLE 3.3.8.1.4-3. HRF RACK MOUNTED EQUIPMENT LOAD FACTORS
(EQUIPMENT FREQUENCY 35 Hz)
|LIFTOFF |X |Y |Z |
|(G) |(7.7 |(11.6 |(9.9 |
| | | | |
|LANDING |X |Y |Z |
|(G) |(5.4 |(7.7 |(8.8 |
NOTE: LOAD FACTORS APPLY CONCURRENTLY IN ALL POSSIBLE COMBINATIONS FOR EACH EVENT AND ARE SHOWN IN THE RACK COORDINATE SYSTEM DEFINED IN SSP 41017, PART 2, PARAGRAPH 3.1.3.
3.3.8.2 Electrical Power Consuming Equipment Design
3.3.8.2.1 Batteries
All battery systems shall meet the requirements of NSTS 1700.7, ISS addendum, Section 213.2. (Derived from LS-71000, Section 6.2.2.14)
3.4 ACCEPTANCE AND QUALIFICATION REQUIREMENTS
3.4.1 Thermal Environment Compatibility
A. VOILA shall operate nominally during exposure to 17 °C to 28 °C (63 °F to 82 °F).
B. VOILA shall operate nominally following exposure to 10 °C to 46 °C (50 °F to 115 °F).
3.4.2 Vibration and Sine Sweep
A. VOILA shall perform a sinusoidal resonance survey.
B. VOILA shall operate nominally following vibration at flight vibration loads.
C. VOILA shall operate nominally following vibration at workmanship loads.
3.4.3 Functional Acceptance
VOILA shall complete a functional test as outlined in a TPS. (LS-71000, Section 5.4.1.3.4)
3.4.4 Electrical, Electronic and Electromechanical Parts Control, Selection and Burn-In
A. Parts control shall be in accordance with SSP 30312, “Electrical, Electronic, and Electromechanical (EEE) and Mechanical Parts Management and Implementation Plan for Space Station Program.”
B. Parts selection for equipment shall be in accordance with:
1. SSP-30423, “Space Station Approved Electrical, Electronic and Electromechanical (EEE) Parts List.”
2. SSQ-25002, “Supplemental List of Qualified Electrical, Electronic, Electromechanical (EEE) Parts, Manufacturers and Laboratories (QEPM&L).”
3. Semiconductors shall be JANTXV in accordance with MIL-PRF-19500, “Performance Specification Semiconductor Devices, General Specification for.” Diodes shall have a metallurgical bond. Passive parts shall be at least the second highest level of appropriate Military Established Reliability (MIL-ER).
4. SSP-30512C, “Space Station Ionizing Radiation Design Environment.”
Where no alternative is available, nonmilitary parts, components and subassemblies may be used, but burn-in screening of these items shall be performed per 3.4.4C.
C. Burn-in screening shall be completed (100%) on all flight hardware (units).
3.4.5 Flammability
VOILA shall meet the flammability test requirements as described in 4.3.5.
3.4.6 Offgassing
VOILA shall meet the offgassing test requirements as described in 4.3.6.
3.4.7 Shock
Not applicable to VOILA.
3.4.8 Bench Handling
VOILA shall meet the requirements as described in 4.3.8.
3.4.9 Payload Mass
VOILA shall meet the payload mass control requirements as described in 4.3.9.
3.4.10 Electromagnetic Compatibility
VOILA shall meet the EMC control requirements as described in 4.3.10.
3.4.11 Acoustic Noise
VOILA shall meet the acoustic noise control requirements as described in 4.3.11.
3.4.12 Safety Critical Structure Verification
3.4.12.1 Safety Critical Structure Dimensional Check
Dimensions for all VOILA elements identified as safety critical structures shall comply with design dimensions.
3.4.12.2 Safety Critical Structure Material Certification
Material composition for all VOILA flight unit elements that are identified as safety critical structures shall be fabricated from the materials and alloys in the final design drawings, and shall be fabricated from materials approved by NASA-JSC.
3.4.13 Software Acceptance
VOILA software shall meet the software acceptance requirements as described in 4.3.13. (LS-71000, Section 5.4.1.3.1)
3.4.14 Pre-Delivery Acceptance
VOILA equipment shall meet the pre-delivery acceptance requirements as described in 4.3.14. (LS-71000, Section 5.4.1.3.2)
3.4.15 Pre-Installation Acceptance
VOILA shall meet the pre-installation acceptance requirements as described in 4.3.15. (LS-71000, Section 5.4.1.3.3)
3.5 HRP PROGRAM REQUIREMENTS
3.5.1 Safety
VOILA shall meet the applicable requirements of NSTS 1700.7, NSTS 1700.7 ISS Addendum, NSTS/ISS 18798, NSTS/ISS 13830, and KHB 1700.7.
3.5.2 Documentation Requirements
Documentation requirements VOILA shall be as specified in Appendix A of the PRD for HRF, LS-71000. Required items for submittal to NASA are summarized below for convenience.
3.5.2.1 Acceptance Data Package (ADP)
The contents of the ADP shall be based upon SSP 30695, Acceptance Data Package Requirements Specification but shall also include the following:
| | |Required for Project| |
|# |Document |Yes |No |Comments |
|1 |Engineering Drawings | | | |
|2 |Inventory of Serialized Components | | | |
|3 |Operating, Maintenance, and Handling | | | |
| |Procedures | | | |
|4 |“As run” Test Procedures, Data, and Reports | | | |
|5 |Safety Data | | | |
|6 |Structural Analyses | | | |
|7 |Radioactive Material Data | | | |
|8 |Calibration Data | | | |
1. Engineering Drawings: As-built engineering drawings shall be provided. The drawings shall include the top assembly drawing for each major component and any other drawings necessary to perform receiving inspection and any test or operation to be performed at the destination.
2. Inventory of Serialized Components: A list of “field replaceable” serialized components will be included in the ADP. The list will contain the component part number, component name and component serial number.
3. Operating, Maintenance, and Handling Procedures: Each delivered functional end item shall have a separate manual covering its maintenance, repair, and operation. The manual shall include, but not be limited to, the following (as applicable):
a. Operational instructions suitable to support operator training and containing a system description and general instructions for operating the equipment.
b. Any special handling, packing, transportation or storage procedures (i.e., must be stored/transported in a specific orientation, specific environmental conditions, etc.)
c. A list of special tools, support and facilities equipment and all other materials necessary to perform maintenance.
d. A schedule chart listing the time at which all maintenance is to be performed. This shall also include inspection for required repair, maintenance, or replacement of parts.
e. Conditions of environment in which maintenance is to be performed.
f. Detailed maintenance procedures that describe removal, disassembly, type of maintenance or repair, cleaning, reassemble and reinstallation of all parts or subassemblies. Also included shall be points of inspection and notes of caution.
g. Illustrated part breakdowns showing the details of the part being worked on.
h. Schematic and interconnecting wiring diagrams in sufficient detail to enable troubleshooting to be performed down to the replaceable subassembly or printed circuit board level.
i. Fault analysis will be provided to facilitate maintenance. The repair procedures shall be adequate for testing, checkout, disassembly, cleaning, inspection, repair, reassembly, adjustment, calibration and servicing of the equipment as applicable.
4. “As Run” Test Procedures and Reports: The original “as run” test procedures used for any of the testing required in this HRD, along with any associated data and test reports shall be included in the ADP. These procedures shall include quality approval, if applicable, as documented in the Quality Plan.
5. Safety Data: Copies of hazard reports and other safety data prepared or collected as a result of ground and/or flight safety requirements.
6. Structural Analyses: Copies of any structural analyses performed as specified in this HRD or required in the contract with NASA.
7. Radioactive Material Data: If the shipment contains any radioactive material, this section shall include copies of all required data on radioactive material.
8. Calibration Data: This section shall include any calibration or scaling data required to interpret the output signals from or measurements made using the equipment being shipped.
3.5.2.1.1 ADP Statement in SOW
The SOW for procured flight items shall contain a DRD specifying the above ADP contents.
3.5.2.2 Additional Required Documentation
4.0 VERIFICATION PROVISIONS
This section contains the required verification methods for ISS interface certification, science functional acceptance and program qualification and acceptance. Section 4.1 addresses definitions for terms used herein.
Appendix B contains the applicability matrix for ISS Pressurized Payload Interface Requirements Document requirements. The Verification Data Sheet addressing the appropriate method for ISS interface verification is also contained in Appendix B. If an alternate verification method is desired, the new verification method must be negotiated in the Unique Payload Verification Plan.
Section 4.2 contains the verification methods for science functional acceptance. Appendix C contains the applicability matrix for science functional requirements.
Section 4.3 contains the verification methods for program qualification and acceptance requirements. Appendix D contains the applicability matrices for acceptance and qualification requirements.
The responsibility for the performance of all verification activities is as specified in Appendices B, C and D. All testing described in Appendices B, C and D shall be documented via TPS (JSC Form 1225) per JSC Work Instruction NT1-CWI-001. Except as otherwise specified in the contract, providers may use their own or any other facility suitable for the performance of the verification requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the verifications set forth in this specification.
4.1 GENERAL
Equipment verification methods are defined as follows:
A. Inspection is a method that determines conformance to requirements by the review of drawings, data or by visual examination of the item using standard quality control methods, without the use of special laboratory procedures.
B. Analysis is a process used in lieu of, or in addition to, other methods to ensure compliance to specification requirements. The selected techniques may include, but not be limited to, engineering analysis, statistics and qualitative analysis, computer and hardware simulations, and analog modeling. Analysis may also include assessing the results of lower level qualification activity. Analysis may be used when it can be determined that (1) rigorous and accurate analysis is possible, (2) test is not cost effective, and (3) verification by inspection is not adequate.
Verification by similarity is the process of analyzing the specification criteria for hardware configuration and application for an article to determine if it is similar or identical in design, manufacturing process, and quality control to an existing article that has previously been qualified to equivalent or more stringent specification criteria. Special effort will be made to avoid duplication of previous tests from this or similar programs. If the previous application is considered to be similar, but not equal to or greater in severity, additional qualification tests shall concentrate on the areas of new or increased requirements.
C. Demonstration consists of a qualitative determination of the properties of a test article. This qualitative determination is made through observation, with or without special test equipment or instrumentation, which verifies characteristics such as human engineering features, services, access features, and transportability. Demonstration requirements are normally implemented within a test plan, operations plan, or test procedure.
D. Test is a method in which technical means, such as the use of special equipment, instrumentation, simulation techniques, and the application of established principles and procedures, are used for the evaluation of components, subsystems, and systems to determine compliance with requirements. Test shall be selected as the primary method when analytical techniques do not produce adequate results; failure modes exist which could compromise personnel safety, adversely affect flight systems or payload operation, or result in a loss of mission objectives; or for any components directly associated with Space Station and orbiter interfaces. The analysis of data derived from tests is an integral part of the test program, and should not be confused with analysis as defined above.
4.2 FUNCTIONAL PERFORMANCE ACCEPTANCE TESTING
The requirements herein describe specific test requirements for functional performance acceptance.
4.3 ACCEPTANCE AND QUALIFICATION VERIFICATION METHODS
The requirements herein describe specific test requirements for VOILA acceptance and qualification. Qualification testing shall only be performed if qualification articles exist for the hardware. If no qualification articles exist for the hardware, analysis may be used to qualify the hardware.
4.3.1 Thermal Cycle Tests
HRF payloads undergoing thermal cycle testing shall be functionally tested at each stable temperature and during transitions. The pass-fail criteria for the functional test and the definition of the functional test will be equipment unique and shall be defined in the test plan and test procedure. Functional tests shall be conducted on end items prior to, during, and after environmental exposure. (LS-71000, Section 5.4.1.1.6)
4.3.1.1 Qualification Thermal Cycle Test
The Qualification Thermal Cycle Test shall be conducted over a temperature range of 61.1 (C (110 (F) centered around the midpoint of the normal operating temperature as defined in Section 3.4.1.A. One cycle is defined as starting from normal operating temperature, increasing to the maximum high temperature, decreasing to the minimum low temperature and then returning to the normal operating temperature as depicted in Figure 4.3.1.1-1. The complete test is seven and one-half (7½) cycles with one-hour soaks at each extreme. The hardware shall be functionally tested during transitions and at the highest and lowest temperature extremes, consistent with the defined operating temperature range. The hardware shall not be functionally tested at temperatures in excess of the defined operating temperature range. Hardware shall be unpowered when outside the manufacturer’s operating limits. The specific profile shall be defined in the individual test plans. (LS-71000, Section 5.4.1.1.6.1)
4.3.1.2 Acceptance Thermal Cycle Test
An acceptance thermal test shall be performed on all flight and flight alternate hardware. The acceptance thermal cycle shall be conducted over a temperature range of 55.6 (C (100 (F) centered around the midpoint of the normal operating temperature as defined in section 3.4.1.A. One cycle is defined as starting from normal operating temperature, increasing to the maximum high temperature, decreasing to the minimum low temperature and then returning to the normal operating temperature as depicted in Figure 4.3.1.2-1. The complete test consists of one and one-half (1½) thermal cycles with one-hour soaks at each extreme. The hardware shall be functionally tested before and after the temperature test, at each transition, and at each stable temperature. The hardware shall not be functionally tested at temperatures in excess of the defined operating temperature range. Hardware shall be unpowered when outside the manufacturer’s operating limits. (LS-71000, Section 5.4.1.1.6.2)
[pic]
Figure 4.3.1.1-1. Qualification Thermal Cycling
[pic]
Figure 4.3.1.2-1. Acceptance Thermal Cycling
4.3.2 Vibration Tests
Sinusoidal Resonance Survey test levels are as described in Section 4.3.2.1. Qualification Vibration Analysis is as described in Section 4.3.2.2.1. Qualification for Acceptance Vibration Test levels are as described in Section 4.3.2.2.2. Acceptance Vibration Test levels are as described in Section 4.3.2.2.3.
4.3.2.1 Sinusoidal Resonance Survey
HRF rack mounted instruments shall be subjected to a sinusoidal resonance survey to determine the fundamental resonance frequencies of the test article. The survey shall be conducted at a sweep rate of one octave per minute in each of three orthogonal axes from 5 to 200 Hz, one sweep up and down, with an input not to exceed 0.25 g zero to peak. The equipment under test shall have an accelerometer mounted at an accessible hard point on the test item near or on the center of gravity of the test article. The output of this response accelerometer shall be monitored and not allow the hardware to experience more than 0.5 g peak. The input acceleration level shall be monitored by an accelerometer mounted as close as possible to the test fixture/hardware interface. (LS-71000, Section 5.4.1.1.2)
4.3.2.2 Random Vibration Test
Random vibration testing is required for all HRF rack mounted hardware. Random vibration testing is not required for hardware packed in vibration damping materials such as foam, or for hardware launched in soft stowage containers. Each HRF instrument subjected to vibration testing shall be functionally tested before and after vibration testing. Hardware expected to operate during launch shall be operating and functionally tested during vibration testing. The pass-fail criteria for the functional test and the definition of the functional test will be equipment unique and shall be defined in the test plan and test procedure for each element. (LS-71000, Section 5.4.1.1.3)
It is recommended that the hardware be hard mounted to the vibration test fixture in order to achieve a one-to-one transfer of the vibration levels shown in the following paragraphs. If the individual hardware flight mounting configuration is expected to result in amplification of flight vibration levels above the test levels defined in the following paragraphs, a test program should be developed that verifies the survivability of the hardware. (LS-71000, Section 5.4.1.1.3)
Requirements for qualification vibration testing are defined in SSP 52005. Requirements for acceptance vibration testing are defined in SP-T-0023. (LS-71000, Section 5.4.1.1.3)
4.3.2.2.1 Qualification Vibration Analysis
Qualification Vibration Analysis (QVA) certifies the design for launch in the MPLM. The QVA requirement is identical to Section 3.3.8.1.4.A. (LS-71000, Section 5.4.1.1.3.1)
4.3.2.2.2 Qualification for Acceptance Vibration Test
Qualification for Acceptance Vibration Testing (QAVT) determines the number of Acceptance Vibration Tests that may be run on flight units. QAVT shall be run on dedicated qualification test hardware only. The QAVT for HRF equipment shall be performed at a 7.93 g rms composite level over the frequency range and spectral density defined in Table 4.3.2.2.2-1. QAVT shall be conducted at 1.69 times the Acceptance Vibration Test levels. QAVT duration shall be the Acceptance Vibration Testing (AVT) duration multiplied by the number of AVTs for which the hardware is to be qualified. (LS-71000, Section 5.4.1.1.3.2)
Table 4.3.2.2.2-1. Qualification FOR Acceptance
vibration test levels
|FREQUENCY RANGE (HZ) |MINIMUM POWER SPECTRAL DENSITY (G2/HZ) |
|20 |0.017 |
|20 - 80 |3 DB/OCTAVE SLOPE |
|80 - 350 |0.067 |
|350 - 2000 |-3 DB/OCTAVE SLOPE |
|2000 |0.0118 |
|COMPOSITE |7.93 G RMS |
4.3.2.2.3 Acceptance Vibration Test
AVT is used to screen defects in workmanship that cannot be detected by inspection. AVT for VOILA shall be performed at a 6.1 g rms composite level over the frequency range and minimum AVT levels defined in Table 4.3.2.2.3-1. Vibration duration shall be a minimum of 60 seconds in each of three axes. Functional/continuity tests shall be conducted on components before, during, and after the AVT. (LS-71000 Section 5.4.1.1.3.3)
Table 4.3.2.2.3-1. Acceptance vibration test levels
|FREQUENCY RANGE (HZ) |MINIMUM POWER SPECTRAL DENSITY (G2/HZ) |
|20 |0.01 |
|20 - 80 |+3 DB/OCTAVE - SLOPE |
|80 - 350 |0.04 |
|350 - 2000 |-3 DB/OCTAVE - SLOPE |
|2000 |0.007 |
|COMPOSITE |6.1 G RMS |
4.3.3 Functional Testing
The scope and method of functional testing shall be negotiated between the hardware developer and the quality organization responsible for accepting the hardware. (LS-71000, Section 5.4.1.3.4)
4.3.4 Electrical, Electronic, and Electromechanical Parts Control, Selection, and Burn-In
A Compliance with 3.4.4.A is considered successful when it can be shown via analysis that the parts control process is compliant with 3.4.4.A. (LS-71000, Section 5.4.1.1.10)
B. Compliance with 3.4.4.B is considered successful when an analysis is provided which includes a risk assessment, electrical stress analysis, and data delivery on information such as designed/as-built EEE parts, list, construction history, Government and Industry Data Exchange Program (GIDEP) Alerts, part obsolescence, radiation susceptibility, and/or prior history. (LS-71000, Section 5.4.1.1.10)
C. The burn-in test may be accomplished at the component or assembly level, and is specified as:
• 72 hrs continuously at room ambient temperature while functioning
• 96 hrs continuously at a specified controlled temperature while functioning.
Full functional tests shall be performed on the experiment hardware before and after the burn-in test. Controlled temperature is defined as 15 (C below the maximum rating of the device with the lowest temperature rating in the article under test. (LS-71000, Section 5.4.1.1.10)
All flight assemblies utilizing non-military parts (as specified in Section 3.4.4) shall undergo burn-in testing. (LS-71000, Section 5.4.1.1.10)
4.3.5 Flammability
Payload materials shall be non-flammable or self-extinguishing per the test criteria of NASA-STD-6001, Test 1, Flammability, Odor, Offgassing, and Compatibility Requirements and Test Procedures for Materials in Environments that Support Combustion. The material shall be evaluated in the worst-case use environment at the worst-case use configuration. When the use of a nonflammable material is not possible, a Material Usage Agreement (MUA) or equivalent shall be submitted to the cognizant NASA center for disposition. If test data does not exist for a material, the experimenter may be asked to provide samples (see NASA-STD-6001, Chapter 4) to a NASA certified test facility Marshall Space Flight Center (MSFC) or White Sands Test Facility (WSTF) for flammability testing). (LS-71000, Section 5.4.1.1.8)
Materials transported or operated in the orbiter cabin, or operated in the ISS air lock during Extravehicular Activity (EVA) preparations, shall be tested and evaluated for flammability in the worst-case use environment of 30% oxygen and 10.2 psia. Materials used in all other habitable areas shall be tested and evaluated in the worst-case use environment of 24.1% oxygen and 15.2 psia. (LS-71000, Section 5.4.1.1.8)
4.3.6 Offgassing
All flight hardware located in habitable areas shall be subjected to test and meet the toxicity offgassing acceptance requirements of NASA-STD-6001, Test 7. (LS-71000, Section 5.4.1.1.9)
4.3.7 Shock Test
Not applicale to VOILA.
4.3.8 Bench Handling
A bench handling test shall be performed on the qualification unit for all stowed hardware. The bench handling test shall be conducted in accordance with MIL-STD-810, Section 516.4,I-3.8, Procedure VI with the following modifications: Number of actual drops depends upon hardware configuration and will be negotiated with JSC/NT prior to testing. Surfaces, corners, edges shall be identified in the test procedure. (LS-71000, Section 5.4.1.1.5)
4.3.9 Payload Mass
VOILA shall comply with LS-71014, Mass Properties Control Plan. (LS-71000, Section 5.4.1.1.1)
4.3.10 Electromagnetic Compatibility
VOILA shall comply with LS-71016, HRF EMI/EMC Control Plan. (LS-71000, Section 5.4.1.2.1)
4.3.11 Acoustic Noise
VOILA shall comply with LS-71011, Acoustic Noise Control and Analysis Plan for Human Research Facility Payloads and Racks. (LS-71000, Section 5.4.1.1.7)
4.3.12 Safety Critical Structure Verification
4.3.12.1 Safety Critical Structure Dimensional Check
VOILA elements identified as safety critical structures shall be verified to be in accordance with the final design drawing dimensional requirements. (LS-71000, Section 5.4.1.1.11.1)
4.3.12.2 Safety Critical Structure Material Certification
All structural elements that are identified as safety critical structure of each of the flight units shall have the components used in those safety critical structures certified to be fabricated from the materials and alloys identified in the final design drawing, and to be fabricated from materials approved by NASA-JSC. (LS-71000, Section 5.4.1.1.11.2)
4.3.13 Software Acceptance
Software shall be acceptance tested per LS-71020. (LS-71000, Section 5.4.1.3.1)
4.3.14 Pre-Delivery Acceptance
The responsible manufacturing parties shall perform a Pre-Delivery Acceptance (PDA) after the complete fabrication and assembly has been conducted for all Class I deliverable assemblies. This test shall include verification of software interface and operation. The PDA must be completed before hardware certification testing begins. It is a full functional test and inspection that validates that the hardware operates per the design requirements and that it is constructed per released engineering drawings. All PDA tests shall be approved by the hardware’s JSC technical monitor and JSC/NT3, as well as the contractor quality engineering (if applicable). The following are standard steps that each PDA test shall contain:
1. Conformance to Drawing. Verify that the hardware conforms to released engineering drawings.
2. No Sharp Edges. Inspect the hardware to verify that there are no sharp edges or corners present.
3. Proper Identifying Markings. Verify that the hardware has the proper part number and serial number (if applicable) on it.
4. Weight and Center of Gravity. Measurements shall be taken of the as-built configuration per Section 3.2.2.1 of this document.
5. Functional Testing. This is a full functional test and checks all interfaces.
(LS-71000, Section 5.4.1.3.2)
4.3.15 Pre-Installation Acceptance (PIA)
PIA testing occurs prior to installation in the HRF Rack.
1. Cleanliness. PIA tests shall include verification that surfaces are to the cleanliness level of Section 3.3.1.1.4 of this document.
2. Functional Testing. PIA functional testing checks rack interfaces prior to installation in the HRF Rack.
(LS-71000, Section 5.4.1.3.3)
5.0 PREPARATION FOR SHIPMENT
5.1 General
A. The methods of preservation, packaging, and packing used for shipment, together with necessary special control during transportation, shall adequately protect the article(s) from damage or degradation in reliability or performance as a result of the natural and induced environments encountered during transportation and subsequent indoor storage. (LS-71000, Section 9.1A)
B. To reduce program cost, prior to developing a newly designed container, every effort will be made by project participants to use container designs and/or containers available commercially or from Government inventories. If reusable containers are not available, a screening process should be initiated for container availability in the following priority: existing containers, commercial off-the-shelf containers and modified commercial off-the shelf containers. Shipping containers and protective devices will be designed for effective and economical manufacture, procurement and transportability. (LS-71000, Section 9.1B)
5.2 Packing, Handling and Transportation
A. Packaging, handling and transportation shall be in accordance with applicable requirements of NHB 6000.1C and referenced documents therein. (LS-71000, Section 9.2A)
B. Documented procedures and physical controls shall be established to ensure that the HRF rack and individual items of equipment will not be subjected to temperature, shock and humidity outside the non-operational limits during shipment. LS-71000, Section 9.2C)
C. VOILA shall be cleaned to the “Visibly Clean Level 1 (Sensitive)” as determined in JSC-SN-C-0005, Specification Contamination Control Requirements for the Shuttle Program. LS-71000, Section 9.2D)
5.3 Preservation and Packing
Preservation and packing shall be in accordance with approved Packaging, Handling and Transportation Records (PHTRs). (LS-71000, Section 9.3)
5.4 Marking for Shipment
Interior and exterior containers shall be marked and labeled in accordance with NHB 6000.1C including precautionary markings necessary to ensure safety of personnel and facilities, and to ensure safe handling, transport, and storage. Should the individual items of equipment contain any hazardous materials, markings shall also comply with applicable requirements governing packaging and labeling of hazard materials. Packages with reuse capability shall be identified with the words “Reusable Container - Do Not Destroy - Retain for Reuse.” NASA Critical Item Labels (Form 1368 series) shall be applied in accordance with NHB 6000.1C. (LS-71000, Section 9.4)
5.5 NASA Critical Space Item Label
The NASA Critical Space Item Labels Form 1368 shall be affixed to exterior and interior shipping containers in accordance with NHB 6000.1C. (LS-71000, Section 9.5A)
6.0 NOTES
This section contains information of a general or explanatory nature that may be helpful but is not mandatory.
6.1 Definitions
|Qualification Test |Test conducted as part of the certification program to demonstrate that the |
| |design and performance requirements can be realized under specified |
| |conditions. |
|Acceptance Test |Formal tests conducted to assure that the end item meets specified |
| |requirements. Acceptance tests include performance demonstrations and |
| |environmental exposures to screen out manufacturing defects, workmanship |
| |errors, incipient failures and other performance anomalies not readily |
| |detectable by normal inspection techniques or through ambient functional |
| |tests. |
|Active Air Exchange |Forced convection between two volumes. For example, forced convection |
| |between a subrack payload and the internal volume of an integrated rack, or |
| |forced convection between a subrack payload and cabin air. |
|Continuous Noise Source |A significant noise source that exists for a cumulative total of eight hours|
| |or more in any 24-hour period is considered to be a continuous noise source.|
|Intermittent Noise Source |A significant noise source that exists for a cumulative total of less than |
| |eight hours in a 24-hour period is considered to be an intermittent noise |
| |source. |
|On-Orbit Momentary Protrusions |Payload Obstructions that typically would protrude for a very short time or |
| |could be readily eliminated by the crew at any time. Momentary protrusions |
| |include only the following: drawer/door/cover replacement or closure. |
|On-Orbit Permanent Protrusion |A payload hardware item that is not ever intended to be removed. |
|On-Orbit Semi-Permanent Protrusion |A payload hardware item that is typically left in place, but can be removed |
| |by the crew with hand operations or standard IVA tools. Example: SIR and |
| |ISIS drawer handles, other equipment that does not interfere with crew |
| |restraints and mobility aids. |
|On-Orbit Temporary Protrusion |A payload item that is typically located in the aisle for experiment |
| |purposes only. These items should be returned to their stowed configuration|
| |when not being used. Example: Front panel mounted equipment. |
APPENDIX A
RESERVED
APPENDIX B
ISS PRESSURIZED PAYLOAD INTERFACE REQUIREMENTS
DOCUMENT VERIFICATION MATRIX
APPENDIX B
ISS PRESSURIZED PAYLOAD INTERFACE REQUIREMENTS DOCUMENT VERIFICATION MATRIX
|HRD |LS-71000 |SSP 57000 | | |Verification | | |
|Section |Section |Section |Requirement |Applicable |Method |Responsibility |Comments |
|3.2.2.2.2.1B |-- |3.1.1.7B |On-Orbit Payload Protrusions - Attachment of RMA |E |Per ICD |HRF |Equipment will attach to |
| | | | | | | |seat track when deployed |
|3.2.2.2.2.1.1 |-- |3.1.1.7.1 |On-Orbit Permanent Protrusions |N/A |N/A |N/A |No permanent protrusions |
|3.2.2.2.2.1.2A |-- |3.1.1.7.2A |On-Orbit Semi-Permanent Protrusions - SIR and ISIS |( |Per ICD |HRF | |
| | | |Drawer Handles | | | | |
|3.2.2.2.2.1.2B |-- |3.1.1.7.2B |On-Orbit Semi-Permanent Protrusions - Other |( |Per ICD |HRF | |
|3.2.2.2.2.1.2C |-- |3.1.1.7.2C |On-Orbit Semi-Permanent Protrusions - Removable |( |Per ICD |HRF | |
|3.2.2.2.2.1.3A |-- |3.1.1.7.3A |On-Orbit Temporary Protrusions - Envelope |E |Per ICD |HRF |Equipment will exceed the|
| | | | | | | |17 inch envelope when |
| | | | | | | |deployed |
|3.2.2.2.2.1.3B |-- |3.1.1.7.3B |On-Orbit Temporary Protrusions - Removal |( |Per ICD |HRF | |
|3.2.2.2.2.1.4 |-- |3.1.1.7.4 |On-Orbit Momentary Protrusions |N/A |N/A |N/A |No momentary protrusions |
|3.2.4A |6.4.4.2.6.3 |3.12.4.2.8.4 |Maintainability - Unique Tools |N/A |N/A |N/A |No unique tools |
|3.2.4B |6.4.4.3.1 |3.12.4.3.1 |Maintainability - One-handed Operation |N/A |N/A |N/A |No planned maintenance |
|3.2.4C |6.4.4.3.2B |3.12.4.3.2A2 |Maintainability - Connector Mate/Demate |N/A |N/A |N/A |No planned maintenance |
|3.2.4D |6.4.4.3.2C |3.12.4.3.2B |Maintainability - No Damage to Wiring Connectors |( |Per ICD |HRF | |
|APPENDIX B |
| |
|ISS PRESSURIZED PAYLOAD INTERFACE REQUIREMENTS DOCUMENT VERIFICATION MATRIX (Cont’d) |
|HRD |LS-71000 |SSP 57000 | | |Verification | | |
|Section |Section |Section |Requirement |Applicable |Method |Responsibility |Comments |
|3.2.4F |6.4.3.1.2A |3.12.3.1.2A |Maintainability - Built-in Control |N/A |N/A |N/A |No liquids or particulate |
| | | | | | | |matter |
|3.2.4G |6.4.3.1.2B |3.12.3.1.2B |Maintainability - Access to Filters for |( |Per ICD |HRF | |
| | | |Replacement/Cleaning | | | | |
|3.2.4.1.1 |6.4.10 |3.12.10 |Payload In-flight Maintenance |N/A |N/A |N/A |No planned maintenance |
|3.2.5.1.1.1 |6.2.9.1.1 |3.9.1.1 |Pressure |( |Per ICD |HRF | |
|3.2.5.1.1.2 |6.2.9.1.2 |3.9.1.2 |Temperature |( |Per ICD |HRF | |
|3.2.5.1.1.3 |6.2.9.1.3 |3.9.1.3 |Humidity |N/A |N/A |N/A |No cold sources |
|3.2.5.1.2.1 |6.2.9.2.1 |3.9.2.1A |Active Air Exchange |N/A |N/A |N/A |No air exchange with cabin |
|3.2.5.1.2.2 |6.2.9.2.2 |3.9.2.2 |Oxygen Consumption |N/A |N/A |N/A |No oxygen consumption |
|3.2.5.1.2.3 |6.2.9.2.3 |3.9.2.3 |Chemical Releases |( |Per ICD |HRF | |
|3.2.5.1.2.4 |6.2.5.4 |3.5.1.12 |Cabin Air Heat Leak |( |Per ICD |HRF | |
|3.2.5.1.3.1 |6.2.9.3.1 |3.9.3.1 |Instrument Contained or Generated Ionizing Radiation |( |Per ICD |HRF | |
|3.2.5.1.3.3 |6.2.9.3.3 |3.9.3.3 |Single Event Effect (SEE) Ionizing Radiation |( |Per ICD |HRF | |
|3.2.5.1.5A |6.2.1.1.6B |3.1.1.4B |Pressure Rate of Change - On-orbit |( |Per ICD |HRF | |
|3.2.5.1.5B1 |6.2.1.1.6A |3.1.1.2B |Pressure Rate of Change - MPLM |( |Per ICD |HRF | |
|3.2.5.1.5C |6.2.1.1.6C |3.1.1.4K |Pressure Rate of Change - PFE |( |Per ICD |HRF | |
|3.2.5.1.5D |6.2.1.1.6D |3.1.1.4M |Pressure Relief Device |N/A |N/A |N/A |No pressure relief devices |
|3.2.5.1.6A | |3.1.2.1 |Quasi-Steady Requirements |( |Per ICD |HRF | |
|3.2.5.1.6B | |3.1.2.2 |Vibratory Requirements |( |Per ICD |HRF | |
|3.2.5.1.6C | |3.1.2.3A |Transient Requirements |( |Per ICD |HRF | |
|3.2.5.1.6D | |3.1.2.3B |Transient Requirements |( |Per ICD |HRF | |
|3.2.5.2.1A |6.4.3.3.1A |3.12.3.3.1A |Continuous Noise Limits - Sub-Rack Equipment Not |N/A |N/A |N/A |Mutually exclusive with |
| | | |Changed Out | | | |3.2.5.2.1.B |
|3.2.5.2.1B |6.4.3.3.1B |3.12.3.3.1B |Continuous Noise Limits - Sub-Rack Equipment Changed |( |Per ICD |HRF | |
| | | |Out | | | | |
|3.2.5.2.1C |6.4.3.3.1C |3.12.3.3.1C |Continuous Noise Limits - Independently Operated |N/A |N/A |N/A |Not independently operated |
| | | |Equipment | | | | |
|3.2.5.2.2A |6.4.3.3.2A |3.12.3.3.2 |Intermittent Noise Limits - A-weighted SPL Limits |( |Per ICD |HRF | |
|3.2.5.2.2B |6.4.3.3.2B |3.12.3.3.2 |Intermittent Noise Limits - Cumulative Duration |( |Per ICD |HRF | |
|3.2.5.3A |6.4.3.4A |3.12.3.4A |Lighting Design - Specularity |( |Per ICD |HRF | |
|3.2.5.3B |6.4.3.4B |3.12.3.4B |Lighting Design - Levels |N/A |N/A |N/A |All tasks are in aisle, Not|
| | | | | | | |a glovebox, |
| | | | | | | |No fine tasks |
|3.2.5.3C |6.4.3.4C |3.12.3.4C |Lighting Design - Dimmable |N/A |N/A |N/A |No VOILA unique light |
| | | | | | | |sources |
|3.2.5.3D |6.4.3.4D |3.12.3.4D |Lighting Design - Brightness Ratio |N/A |N/A |N/A |Not a glove box |
|3.2.5.3E |6.4.3.4E |3.12.3.4E |Lighting Design - Utilize ISS PUL |N/A |N/A |N/A |PUL no longer available |
|3.2.5.4 |6.2.5.3 |3.5.1.11 |Instrument Surface Temperature |( |Per ICD |HRF | |
|3.2.7.1.1 |6.1.1.6.1 |3.1.1.6.1 |Connector Physical Mate |N/A |N/A |N/A |No direct ISS interface |
|3.2.7.2.7 |6.2.2.8 |3.2.4 |Electromagnetic Compatibility (EMC) |( |Per ICD |HRF | |
|3.2.7.2.7.1 |6.2.2.8.1 |3.2.4.1 |Electrical Grounding |( |Per ICD |HRF | |
|3.2.7.2.7.2 |6.2.2.8.2 |3.2.4.2 |Electrical Bonding |( |Per ICD |HRF | |
|3.2.7.2.7.3A |6.2.2.8.4 |3.2.4.4 |Electromagnetic Interference |( |Per ICD |HRF | |
|3.2.7.2.7.3B |6.2.2.8.4 |3.2.4.4 |Electromagnetic Interference - Alternative Use of |( |Per ICD |HRF | |
| | | |RS03PL | | | | |
|3.2.7.2.8A |6.2.2.9 |3.2.4.5 |ESD ( 4000V |( |Per ICD |HRF | |
|3.2.7.2.8B |6.2.2.9 |3.2.4.5 |ESD between 4000 V and 15000 V - Labeling EPCE |( |Per ICD |HRF | |
|3.2.7.2.8C |6.2.2.9 |3.2.4.5 |ESD Labeling |( |Per ICD |HRF | |
|3.2.7.2.9 |6.2.2.12 |3.2.4.8 |Corona |N/A |N/A |N/A |No internal voltages above |
| | | | | | | |190 VDC |
|3.2.7.2.10 |6.2.2.8.3 |3.2.4.3 |Cable/Wire Design and Control Requirements |( |Per ICD |HRF | |
|3.2.7.2.10.1A |6.2.2.7.1A |3.2.3.1B |Wire Derating - Instruments Connected to HRF Rack 28 |( |Per ICD |HRF | |
| | | |V Power Outlets | | | | |
|3.2.7.2.10.2 |6.2.2.7.2 |3.2.3.2B |Exclusive Power Feeds |( |Per ICD |HRF | |
|3.2.7.2.11 |6.2.2.7.3 |3.2.3.3 |Loss of Power |( |Per ICD |HRF | |
|3.2.7.2.12 |6.2.2.10 |3.2.4.6 |AC Magnetic Fields |( |Per ICD |HRF | |
|3.2.7.2.13 |6.2.2.11 |3.2.4.7 |DC Magnetic Fields |( |Per ICD |HRF | |
|3.2.7.3.10.1 |6.2.3.10.1 |3.3.2.3B |Data Transmissions |N/A |N/A |N/A |No direct ISS data |
| | | | | | | |interface |
|3.2.7.3.10.2A |6.2.3.10.2A |3.3.4.1A |CCSDS Data: Space to Ground |N/A |N/A |N/A |No direct ISS data |
| | | | | | | |interface |
|3.2.7.3.10.2B |6.2.3.10.2B |3.3.4.1B |CCSDS Data: Ground to Space |N/A |N/A |N/A |No direct ISS data |
| | | | | | | |interface |
|3.2.7.3.10.2C |6.2.3.10.2C |3.3.4.1C |CCSDS Data: Instrument to P/L MDM |N/A |N/A |N/A |No direct ISS data |
| | | | | | | |interface |
|3.2.7.3.10.2.1 |6.2.3.10.2.1 |3.3.4.1.1 |CCSDS Data Packets |N/A |N/A |N/A |No direct ISS data |
| | | | | | | |interface |
|3.2.7.3.10.2.1.1 |6.2.3.10.2.1.1 |3.3.4.1.1.1 |CCSDS Primary Header |N/A |N/A |N/A |No direct ISS data |
| | | | | | | |interface |
|3.2.7.3.10.2.1.2A |6.2.3.10.2.1.2A |3.3.4.1.1.2A |CCSDS Secondary Header - Location |N/A |N/A |N/A |No direct ISS data |
| | | | | | | |interface |
|3.2.7.3.10.2.1.2B |6.2.3.10.2.1.2B |3.3.4.1.1.2B |CCSDS Secondary Header - format |N/A |N/A |N/A |No direct ISS data |
| | | | | | | |interface |
|3.2.7.3.10.2.2 |6.2.3.10.2.2 |3.3.4.1.2 |CCSDS Data Field |N/A |N/A |N/A |No direct ISS data |
| | | | | | | |interface |
|3.2.7.5.1.2A |6.2.5.1.2A |3.5.1.2A |ITCS Fluid Use |N/A |N/A |N/A |No fluid interfaces |
|3.2.7.5.1.2B |6.2.5.1.2B |3.5.1.2B |Rack dependent Instrument Charging |N/A |N/A |N/A |No fluid interfaces |
|3.2.7.5.1.4 |6.2.5.1.4 |3.5.1.7A |Coolant Maximum Design Pressure |N/A |N/A |N/A |No fluid interfaces |
|3.2.7.5.1.5 |6.2.5.1.5 |3.5.1.16 |Payload Coolant Quantity |N/A |N/A |N/A |No fluid interfaces |
|3.2.7.5.1.6 |6.2.5.1.6 |3.5.1.8 |Fail Safe Design |N/A |N/A |N/A |No fluid interfaces |
|3.2.7.5.1.7 |6.2.5.1.7 |3.5.1.9 |Leakage |N/A |N/A |N/A |No fluid interfaces |
|3.2.7.5.1.8 |6.2.5.1.8 |3.5.1.10 |Quick-Disconnect Air Inclusion |N/A |N/A |N/A |No fluid interfaces |
|3.2.7.6.2.1A |6.2.6.2.1A |3.6.1.2A |VES Input Pressure Limit - Rack-to-Station Interface |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.1B |6.2.6.2.1B |3.6.1.2B |VES Input Pressure Limit - Maximum Design Pressure |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.1C |6.2.6.2.1C |3.6.1.2C |VES Input Pressure Limit - Two Failure Tolerance |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.2 |6.2.6.2.2 |3.6.1.3 |VES Input Temperature Limit |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.3 |6.2.6.2.3 |3.6.1.4 |VES Input Dewpoint Limit |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.4A |6.2.6.2.4A |3.6.1.5A |VES Acceptable Exhaust Gases - Compatibility |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.4B |6.2.6.2.4B |3.6.1.5B |VES Acceptable Exhaust Gases - Non-reactivity |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.4C |6.2.6.2.4C |3.6.1.5C |VES Acceptable Exhaust Gases - Gas Removal |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.4D |6.2.6.2.4D |3.6.1.5D |VES Acceptable Exhaust Gases - Particulate Removal |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.5 |6.2.6.2.5 |3.6.1.5.2 |VES External Contamination Control |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.6A |6.2.6.2.6A |3.6.1.5.3A |VES Incompatible Gases - Containment |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.2.6B |6.2.6.2.6B |3.6.1.5.3B |VES Incompatible Gases - Containment Hardware |N/A |N/A |N/A |No VES/WGS interface |
|3.2.7.6.3.1A |6.2.6.3.1A |3.6.2.2A |VRS Input Pressure Limit -Vented VRS Gases |N/A |N/A |N/A |No VRS/VVS interface |
|3.2.7.6.3.1B |6.2.6.3.1B |3.6.2.2B |VRS Input Pressure Limit - Maximum Design Pressure |N/A |N/A |N/A |No VRS/VVS interface |
|3.2.7.6.3.1C |6.2.6.3.1C |3.6.2.2C |VRS Input Pressure Limit - Two Failure Tolerance |N/A |N/A |N/A |No VRS/VVS interface |
|3.2.7.6.3.2 |6.2.6.3.2 |3.6.2.3 |VRS Through-Put Limit |N/A |N/A |N/A |No VRS/VVS interface |
|3.2.7.7.1.2 |6.2.7.1.2 |3.7.1.1 |Nitrogen Interface Control |N/A |N/A |N/A |No use of nitrogen |
|3.2.7.7.1.3 |6.2.7.1.3 |3.7.1.2 |Nitrogen Interface MDP |N/A |N/A |N/A |No use of nitrogen |
|3.2.7.7.1.4 |6.2.7.1.4 |3.7.1.3 |Nitrogen Interface Temperature |N/A |N/A |N/A |No use of nitrogen |
|3.2.7.7.1.5 |6.2.7.1.5 |3.7.1.4 |Nitrogen Leakage |N/A |N/A |N/A |No use of nitrogen |
|3.2.7.7.2 |6.2.7.2 |3.7.5 |Pressurized Gas Systems |N/A |N/A |N/A |No use of pressurized gas |
| | | | | | | |bottles |
|3.2.7.7.3 |6.2.7.3 |3.7.6 |Manual Valves |N/A |N/A |N/A |No pressure valves |
|3.2.7.8.1.1 |6.2.8.1.1 |3.8.1.1, |ISS Potable Water Interface Connection |N/A |N/A |N/A |No use of potable water |
| | |3.1.1.6.1 | | | | | |
|3.2.7.8.1.2 |6.2.8.1.2 |3.8.1.2 |Potable Water Interface Pressure |N/A |N/A |N/A |No use of potable water |
|3.2.7.8.1.3A |6.2.8.1.3A |3.8.1.3A |Potable Water Use - Not Returned to Cabin Air as |N/A |N/A |N/A |No use of potable water |
| | | |Humidity | | | | |
|3.2.7.8.1.3B |6.2.8.1.3B |3.8.1.3B |Potable Water Use - Total Use |N/A |N/A |N/A |No use of potable water |
|3.2.7.8.2 |6.2.8.2 |3.8.2 |Fluid System Servicer |N/A |N/A |N/A |No fluid interfaces |
|3.2.7.9.1 |6.2.10.1 |3.10.1 |Fire Prevention |( |Per ICD |HRF | |
|3.2.7.9.2.1.1 | |3.10.2.2.1 |Parameter Monitoring Use |N/A |N/A |N/A |Meets NSTS 22648 |
| | | | | | | |containment requirments |
| | | | | | | |Uses rack and cabin smoke |
| | | | | | | |detectors |
|3.2.7.9.2.1.2A | |3.10.2.2.2.1A |Parameter Monitoring in Subrack |N/A |N/A |N/A |Uses aisle smoke detector |
|3.2.7.9.2.1.2B | |3.10.2.2.2.1B |Parameter Monitoring in Subrack |N/A |N/A |N/A |Uses aisle smoke detector |
|3.2.7.9.3.1A |6.2.10.2A |3.10.3.1A |PFE - Small Access Port |N/A |N/A |N/A |No PFE access port required|
|3.2.7.9.3.1B |6.2.10.2B |3.10.3.1B |PFE - Large Access Port |N/A |N/A |N/A |No PFE access port required|
|3.2.7.9.3.2 |6.2.10.3 |3.10.3.2 |Fire Suppression Access Port Accessibility |( |Per ICD |HRF | |
|3.2.7.9.3.3 |6.2.10.4 |3.10.3.3 |Fire Suppressant Distribution |( |Per ICD |HRF | |
|3.2.7.9.4 |6.2.10.5 |3.10.4A |Labeling |N/A |N/A |N/A |Uses rack PFE port |
|3.2.7.10.1 | |3.2.4.9 |Lightning |( |Per ICD |HRF | |
|3.2.7.10.2 | |3.1.1.4E |Rack Requirements – Pivot Keep Out Zone |( |Per ICD |HRF | |
|3.3.1.1.1 |6.2.11.1 |3.11.1 |Materials and Parts use and Selection |( |Per ICD |HRF | |
|3.3.1.1.2 |6.2.11.2 |3.11.1.1 |Commercial Parts |( |Per ICD |HRF | |
|3.3.1.1.3A |6.2.11.3A |3.11.2A |Fluids - General Requirements |N/A |N/A |N/A |No ISS fluid system |
| | | | | | | |interface |
|3.3.1.1.3B |6.2.11.3B |3.11.2B |Fluids - Cleanliness Levels |N/A |N/A |N/A |No ISS fluid system |
| | | | | | | |interface |
|3.3.1.1.3C |6.2.11.3C |3.11.2C |Fluids - Instrument Internal Materials |N/A |N/A |N/A |No ISS fluid system |
| | | | | | | |interface |
|3.3.1.1.4 |6.2.11.4 |3.11.3 |Cleanliness |( |Per ICD |HRF | |
|3.3.1.1.5 |6.2.11.5 |3.11.4 |Fungus Resistant Material |( |Per ICD |HRF | |
|3.3.1.2 |6.4.9.2 |3.12.9.2 |Sharp Edges and Corner Protection |( |Per ICD |HRF | |
|3.3.1.3 |6.4.9.3 |3.12.9.3 |Holes |( |Per ICD |HRF | |
|3.3.1.4 |6.4.9.4 |3.12.9.4 |Latches |( |Per ICD |HRF | |
|3.3.1.5 |6.4.9.5 |3.12.9.5 |Screws and Bolts |( |Per ICD |HRF | |
|3.3.1.6 |6.4.9.6 |3.12.9.6 |Securing Pins |( |Per ICD |HRF | |
|3.3.1.7 |6.4.9.7 |3.12.9.7 |Levers, Cranks, Hooks, and Controls |( |Per ICD |HRF | |
|3.3.1.8 |6.4.9.8 |3.12.9.8 |Burrs |( |Per ICD |HRF | |
|3.3.1.9A |6.4.9.9A |3.12.9.9A |Locking Wires |N/A |N/A |N/A |No locking wires |
|3.3.1.9B |6.4.9.9B |3.12.9.9B |Locking Wires |N/A |N/A |N/A |No fracture critical |
| | | | | | | |devices |
|3.3.2.1 |6.4.7 |3.12.7 |Equipment Identification |( |Per ICD |HRF | |
|3.3.5.1 |6.2.2.14 |3.2.5.1.1 |Electrical Safety |( |Per ICD |HRF | |
|3.3.5.1.1 |6.2.2.14.1.2 |3.2.5.1.2 |Safety-Critical Circuits Redundancy |N/A |N/A |N/A |No safety critical circuits|
|3.3.5.1.2 |6.2.2.13 |3.2.4.10 |EMI Susceptibility for Safety-Critical Circuits |N/A |N/A |N/A |No safety critical circuits|
|3.3.5.1.3A |6.2.2.14.1.1 |3.2.5.1.1 |Mating/Demating of Powered Connectors |( |Per ICD |HRF | |
|3.3.5.1.4A |6.2.2.15A |3.2.5.3A |Power Switches/Controls - Open Supply Circuit |N/A |N/A |N/A |No power sources above 32 |
| | | |Conductors | | | |VDC |
|3.3.5.1.4B |6.2.2.15B |3.2.5.3B |Power Switches/Controls - Power-off |N/A |N/A |N/A |No power sources above 32 |
| | | |Markings/Indications | | | |VDC |
|3.3.5.1.4C |6.2.2.15C |3.2.5.3C |Power Switches/Controls - Supply Circuit not |N/A |N/A |N/A |No standby mode |
| | | |Completely Disconnected | | | | |
|3.3.5.1.5A |6.2.2.16A |3.2.5.4A |GFCI - Output Voltages ( 30 V rms |N/A |N/A |N/A |No portable outlet above 32|
| | | | | | | |VDC |
|3.3.5.1.5B |6.2.2.16B |3.2.5.4B |GFCI - DC Detection Independent of Safety Wire |N/A |N/A |N/A |No GFCI required in |
| | | | | | | |3.3.5.1.5A and 3.3.5.1.5D |
|3.3.5.1.5C |6.2.2.16C |3.2.5.4C |GFCI - AC Detection Dependent on Safety Wire |N/A |N/A |N/A |No GFCI required in |
| | | | | | | |3.3.5.1.5A and 3.3.5.1.5D |
|3.3.5.1.5D |6.2.2.16D |3.2.5.4D |GFCI - Equipment Generating Internal Voltages ( 30 V |N/A |N/A |N/A |No credible fault path |
| | | |rms | | | |through crew |
|3.3.5.1.5E |6.2.2.16E |3.2.5.4E |GFCI - Trip Current |N/A |N/A |N/A |No GFCI required in |
| | | | | | | |3.3.5.1.5A and 3.3.5.1.5D |
|3.3.5.1.5F |6.2.2.16F |3.2.5.4F |GFCI - Power Removal Time |N/A |N/A |N/A |No GFCI required in |
| | | | | | | |3.3.5.1.5A and 3.3.5.1.5D |
|3.3.5.1.5G |6.2.2.16G |3.2.5.4G |GFCI - On-Orbit Testing |N/A |N/A |N/A |No GFCI required in |
| | | | | | | |3.3.5.1.5A and 3.3.5.1.5D |
|3.3.5.1.6A |6.2.2.17A |3.2.5.5A |Portable Equipment/Power Cords - Non-battery Powered |( |Per ICD |HRF | |
| | | |Portable Equipment | | | | |
|3.3.5.1.6B |6.2.2.17B |3.2.5.5B |Portable Equipment/Power Cords - Fault Currents |N/A |N/A |N/A |No credible fault path |
| | | | | | | |through crew |
|3.3.6.1 |6.4.3.1.1 |3.12.3.1.1 |Closures or Covers Design Requirements |( |Per ICD |HRF | |
|3.3.6.3 |6.4.2.3 |3.12.2.3 |Full Size Range Accommodation |( |Per ICD |HRF | |
|3.3.6.4A |6.4.1.1A |3.12.1A1 |Grip Strength |( |Per ICD |HRF | |
|3.3.6.4B |6.4.1.1B |3.12.1A2 |Linear Forces |( |Per ICD |HRF | |
|3.3.6.4C |6.4.1.1C |3.12.1A3 |Torque |( |Per ICD |HRF | |
|3.3.6.5 |6.4.1.2 |3.12.1B |Maintenance Operations |N/A |N/A |N/A |No planned maintenance |
|3.3.6.6 |6.4.2.1 |3.12.2.1 |Adequate Clearance |( |Per ICD |HRF | |
|3.3.6.7A |6.4.2.2A |3.12.2.2A |Accessibility - Geometric Arrangement |( |Per ICD |HRF | |
|3.3.6.7B |6.4.2.2B |3.12.2.2B |Accessibility - Access Openings for Fingers |( |Per ICD |HRF | |
|3.3.6.8 |6.4.3.1.3 |3.12.3.1.5 |One-Handed Operation |( |Per ICD |HRF | |
|3.3.6.9 |6.4.3.2.1 |3.12.3.2.1 |Continuous/Incidental Contact - High Temperature |( |Per ICD |HRF | |
|3.3.6.10 |6.4.3.2.2 |3.12.3.2.2 |Continuous/Incidental Contact - Low Temperature |N/A |N/A |N/A |No cooling functions |
|3.3.6.11 |6.4.4.2.1 |3.12.4.2.1 |Equipment Mounting |( |Per ICD |HRF | |
|3.3.6.12A |6.4.4.2.2A |3.12.4.2.2 |Drawers and Hinged Panels - for routine checkout of |N/A |N/A |N/A |No planned maintenance |
| | | |P/L ORUs | | | | |
|3.3.6.12B |6.4.4.2.2B |3.12.4.2.2 |Drawers and Hinged Panels - remain open without |N/A |N/A |N/A |No planned maintenance |
| | | |manual support | | | | |
|3.3.6.13 |6.4.4.2.3 |3.12.4.2.5 |Alignment |( |Per ICD |HRF | |
|3.3.6.14 |6.4.4.2.4 |3.12.4.2.6 |Slide-Out Stops |( |Per ICD |HRF | |
|3.3.6.15 |6.4.4.2.5 |3.12.4.2.7 |Push-Pull Force |( |Per ICD |HRF | |
|3.3.6.16A |6.4.4.2.6.1A |3.12.4.2.8.1A |Covers - sliding or hinged cap or door |( |Per ICD |HRF | |
|3.3.6.16B |6.4.4.2.6.1B |3.12.4.2.8.1B |Covers - quick-opening cover plate |( |Per ICD |HRF | |
|3.3.6.17 |6.4.4.2.6.2 |3.12.4.2.8.2 |Self-Supporting Covers |( |Per ICD |HRF | |
|3.3.6.18 |6.4.4.3.2A |3.12.4.3.2A1 |Accessibility |( |Per ICD |HRF | |
|3.3.6.19A |6.4.4.3.3A |3.12.4.3.3A |Ease of Disconnect - Nominal Operations |( |Per ICD |HRF | |
|3.3.6.19B |6.4.4.3.3B |3.12.4.3.3B |Ease of Disconnect - ORU Replacement Operations |N/A |N/A |N/A |No planned ORU replacement |
|3.3.6.20 |6.4.4.3.4 |3.12.4.3.4 |Indication of Pressure/Flow |N/A |N/A |N/A |No liquid or gas lines |
|3.3.6.21 |6.4.4.3.5 |3.12.4.3.5 |Self Locking |( |Per ICD |HRF | |
|3.3.6.22A |6.4.4.3.6A |3.12.4.3.6A |Connector Arrangement - Space between Connectors and |( |Per ICD |HRF | |
| | | |Adjacent Obstructions | | | | |
|3.3.6.22B |6.4.4.3.6B |3.12.4.3.6B |Connector Arrangement - Space between Connectors in a|( |Per ICD |HRF | |
| | | |Row | | | | |
|3.3.6.23 |6.4.4.3.7 |3.12.4.3.7 |Arc Containment |( |Per ICD |HRF | |
|3.3.6.24 |6.4.4.3.8 |3.12.4.3.8 |Connector Protection |( |Per ICD |HRF | |
|3.3.6.25 |6.4.4.3.9 |3.12.4.3.9 |Connector Shape |( |Per ICD |HRF | |
|3.3.6.26 |6.4.4.3.10 |3.12.4.3.10 |Fluid and Gas Line Connectors |N/A |N/A |N/A |No fluid or gas lines |
|3.3.6.27 |6.4.4.3.11A |3.12.4.3.11A |Alignment Marks or Guide Pins |( |Per ICD |HRF | |
|3.3.6.28A |6.4.4.3.12A |3.12.4.3.12A |Coding - Unique to Connection |( |Per ICD |HRF | |
|3.3.6.28B |6.4.4.3.12B |3.12.4.3.12B |Coding - Visible |( |Per ICD |HRF | |
|3.3.6.29 |6.4.4.3.13 |3.12.4.3.13 |Pin Identification |( |Per ICD |HRF | |
|3.3.6.30 |6.4.4.3.14 |3.12.4.3.14 |Orientation |( |Per ICD |HRF | |
|3.3.6.31A |6.4.4.3.15A |3.12.4.3.15A |Hose/Cable Restraints - Loose Ends |N/A |N/A |N/A |Not a rack |
|3.3.6.31B |6.4.4.3.15B |3.12.4.3.15B |Hose/Cable Restraints - Clamps |( |Per ICD |HRF | |
|3.3.6.31D |6.4.4.3.15D |3.12.4.3.15D |Hose/Cable Restraints - Loose Cables |( |Per ICD |HRF | |
|3.3.6.32 |6.4.4.4.1 |3.12.4.4.1 |Non-Threaded Fasteners Status Indication |( |Per ICD |HRF | |
|3.3.6.33 |6.4.4.4.2 |3.12.4.4.2 |Mounting Bolt/Fastener Spacing |( |Per ICD |HRF | |
|3.3.6.34 |6.4.4.4.3 |3.12.4.4.4A |Multiple Fasteners |( |Per ICD |HRF | |
|3.3.6.35 |6.4.4.4.4 |3.12.4.4.5 |Captive Fasteners |( |Per ICD |HRF | |
|3.3.6.36A |6.4.4.4.5A |3.12.4.4.6A |Quick Release Fasteners - One turn max |( |Per ICD |HRF | |
|3.3.6.36B |6.4.4.4.5B |3.12.4.4.6B |Quick Release Fasteners - Positive Locking |( |Per ICD |HRF | |
|3.3.6.37 |6.4.4.4.6 |3.12.4.4.7 |Threaded Fasteners |( |Per ICD |HRF | |
|3.3.6.38A |6.4.4.4.7A |3.12.4.4.8A |Over Center Latches - Nonself-latching |N/A |N/A |N/A |No over center latches |
|3.3.6.38B |6.4.4.4.7B |3.12.4.4.8B |Over Center Latches - Latch Lock |N/A |N/A |N/A |No over center latches |
|3.3.6.38C |6.4.4.4.7C |3.12.4.4.8C |Over Center Latches - Latch Handles |N/A |N/A |N/A |No over center latches |
|3.3.6.39 |6.4.4.4.8 |3.12.4.4.9 |Winghead Fasteners |N/A |N/A |N/A |No winghead fasteners |
|3.3.6.40A |6.4.4.4.9A |3.12.4.4.11A |Fastener Head Type - On-Orbit Crew Actuation |( |Per ICD |HRF | |
|3.3.6.40B |6.4.4.4.9B |3.12.4.4.11B |Fastener Head Type - Smooth Surface |( |Per ICD |HRF | |
|3.3.6.40C |6.4.4.4.9C |3.12.4.4.11C |Fastener Head Type - Slotted Fasteners |( |Per ICD |HRF | |
|3.3.6.41 |6.4.4.4.10 |3.12.4.4.12 |One-Handed Actuation |( |Per ICD |HRF | |
|3.3.6.43 |6.4.4.4.12 |3.12.4.4.14 |Access Holes |( |Per ICD |HRF | |
|3.3.6.44 |6.4.5.1 |3.12.5.1 |Controls Spacing Design Requirements |( |Per ICD |HRF | |
|3.3.6.45.1 |6.4.5.2.1 |3.12.5.2.1 |Protective Methods |( |Per ICD |HRF | |
|3.3.6.45.2 |6.4.5.2.2 |3.12.5.2.2 |Noninterference |( |Per ICD |HRF | |
|3.3.6.45.4 |6.4.5.2.4 |3.12.5.2.4 |Barrier Guards |( |Per ICD |HRF | |
|3.3.6.45.5 |6.4.5.2.5 |3.12.5.2.5 |Recessed Switch Protection |N/A |N/A |N/A |No recessed switches |
|3.3.6.46 |6.4.5.2.7 |3.12.5.2.7 |Position Indication |( |Per ICD |HRF | |
|3.3.6.47 |6.4.5.2.8 |3.12.5.2.8 |Hidden Controls |N/A |N/A |N/A |No hidden controls |
|3.3.6.48 |6.4.5.2.9 |3.12.5.2.9 |Hand Controllers |( |Per ICD |HRF | |
|3.3.6.49A |6.4.5.3A |3.12.5.3A |Valve Controls - Low-Torque Valves |N/A |N/A |N/A |No valves |
|3.3.6.49B |6.4.5.3B |3.12.5.3B |Valve Controls - Intermediate-Torque Valves |N/A |N/A |N/A |No valves |
|3.3.6.49C |6.4.5.3C |3.12.5.3C |Valve Controls - High-Torque Valves |N/A |N/A |N/A |No valves |
|3.3.6.49D |6.4.5.3D |3.12.5.3D |Valve Controls - Handle Dimensions |N/A |N/A |N/A |No valves |
|3.3.6.49E |6.4.5.3E |3.12.5.3E |Valve Controls - Rotary Valve Controls |N/A |N/A |N/A |No valves |
|3.3.6.50 |6.4.5.4 |3.12.5.4 |Toggle Switches |( |Per ICD |HRF | |
|3.3.6.51 |6.4.6 |3.12.6 |Restraints and Mobility Aids |( |Per ICD |HRF | |
|3.3.6.51.1A |6.4.6.1A |3.12.6.1A |Stowage Drawer Contents - Restraints |N/A |N/A |N/A |ISS handles stowage |
|3.3.6.51.1B |6.4.6.1B |3.12.6.1B |Stowage Drawer Contents - Restraints |N/A |N/A |N/A |ISS handles stowage |
|3.3.6.51.1C |6.4.6.1C |3.12.6.1C |Stowage Drawer Contents - Restraints |N/A |N/A |N/A |ISS handles stowage |
|3.3.6.51.2A |6.4.6.2A |3.12.6.2A |Stowage and Equipment Drawers/Trays |N/A |N/A |N/A |ISS handles stowage |
|3.3.6.51.2B |6.4.6.2B |3.12.6.2B |Stowage and Equipment Drawers/Trays |N/A |N/A |N/A |ISS handles stowage |
|3.3.6.51.3 |6.4.6.3 |3.12.6.3 |Captive Parts |( |Per ICD |HRF | |
|3.3.6.51.4.1 |6.4.6.4.1 |3.12.6.4.1 |Handles and Restraints |( |Per ICD |HRF | |
|3.3.6.51.4.2 |6.4.6.4.2 |3.12.6.4.3 |Handle Location/Front Access |( |Per ICD |HRF | |
|3.3.6.51.4.3 |6.4.6.4.3 |3.12.6.4.4 |Handle Dimensions |( |Per ICD |HRF | |
|3.3.6.51.4.4A |6.4.6.4.4A |3.12.6.4.5A |Non-Fixed Handles Design Requirements - Stop Position|N/A |N/A |N/A |No non-fixed handles |
|3.3.6.51.4.4B |6.4.6.4.4B |3.12.6.4.5B |Non-Fixed Handles Design Requirements - One Hand Use |N/A |N/A |N/A |No non-fixed handles |
|3.3.6.51.4.4C |6.4.6.4.4C |3.12.6.4.5C |Non-Fixed Handles Design Requirements - |N/A |N/A |N/A |No non-fixed handles |
| | | |Locked/Unlocked Indication | | | | |
|3.3.6.52B |6.4.9.1B |3.12.9.1B |Electrical Hazards - Exposure hazard exceeds |( |Per ICD |HRF | |
| | | |threshold for shock | | | | |
|3.3.6.52C |6.4.9.1C |3.12.9.1C |Electrical Hazards - Exposure hazard exceeds |( |Per ICD |HRF | |
| | | |threshold for shock and threshold of let-go profile | | | | |
|3.3.6.52D |6.4.9.1D |3.12.9.1D |Electrical Hazards - Two dependent controls provided |( |Per ICD |HRF | |
|3.3.6.52E |6.4.9.1E |3.12.9.1E |Electrical Hazards - Three independent hazard |( |Per ICD |HRF | |
| | | |controls | | | | |
|3.3.6.52.1A |6.4.9.1.1A |3.12.9.1.1 |Mismatched - Reversed Connection |( |Per ICD |HRF | |
|3.3.6.52.1B |6.4.9.1.1B |3.12.9.1.1 |Mismatched - Blind Connections |( |Per ICD |HRF | |
|3.3.6.52.1C |6.4.9.1.1C |3.12.9.1.1 |Mismatched - Mismating |( |Per ICD |HRF | |
|3.3.6.52.1D |6.4.9.1.1D |3.12.9.1.1 |Mismatched - Minimizing Equipment Risk |( |Per ICD |HRF | |
|3.3.6.52.2.1 |6.4.9.1.2.1 |3.12.9.1.4.1 |Device Accessibility |( |Per ICD |HRF | |
|3.3.6.52.2.2 |6.4.9.1.2.2 |3.12.9.1.4.2 |Extractor-Type Fuse Holder |N/A |Per ICD |HRF |No fuses |
|3.3.6.52.2.3 |6.4.9.1.2.3 |3.12.9.1.4.3 |Overload Protection Location |( |Per ICD |HRF | |
|3.3.6.52.2.4 |6.4.9.1.2.4 |3.12.9.1.4.4 |Overload Protection Identification |N/A |Per ICD |HRF |No fuses |
|3.3.6.52.2.5 |6.4.9.1.2.5 |3.12.9.1.4.5 |Automatic Restart Protection |( |Per ICD |HRF | |
|3.3.6.53A |6.4.9.10A |3.12.9.10A |Audio Displays - False Alarms |N/A |N/A |N/A |No audio cues |
|3.3.6.53B |6.4.9.10C |3.12.9.10C |Audio Displays - Operability Testing |N/A |N/A |N/A |No audio cues |
|3.3.6.53C |6.4.9.10D |3.12.9.10D |Audio Displays - Manual Disable |N/A |N/A |N/A |No audio cues |
|3.3.6.54 |6.4.9.11 |3.12.9.12 |Egress |( |Per ICD |HRF | |
|3.3.8.1.1A |6.2.1.1.4A |3.1.1.3B |Structural Design Requirements - Positive Safety |( |Per ICD |HRF | |
| | | |Margins for On-orbit Loads | | | | |
|3.3.8.1.1B |6.2.1.1.4B |3.1.1.3D |Structural Design Requirements - Crew Induced Load |( |Per ICD |HRF | |
| | | |Requirements | | | | |
|3.3.8.1.2 |6.2.1.1.1 |3.1.1.5A |Safety Critical Structures Requirements |( |Per ICD |HRF | |
|3.3.8.1.4A |6.2.1.1.3A |3.1.1.3E |Launch and Landing Loads - Random Vibration |( |Per ICD |HRF |Only applicable to VOILA |
| | | | | | | |drawer |
|3.3.8.1.4B |6.2.1.1.3B |3.1.1.3F |Launch and Landing Loads - Load Factors |( |Per ICD |HRF | |
APPENDIX C
FUNCTIONAL PERFORMANCE VERIFICATION MATRIX
APPENDIX C
FUNCTIONAL PERFORMANCE VERIFICATION MATRIX
|HRD Section |LS-71000 |Requirement |Applicable |Verification Method |Comments |
| |Section | | | | |
|3.2.1.1.1.A | |Audio/Video Outputs |( |Test | |
|3.2.1.1.1.B.1 | |Audio/Video Outputs |( |Test | |
|3.2.1.1.1.B.2 | |Audio/Video Outputs |( |Test | |
|3.2.1.1.2.A | |Measurement Ranges |( |Test | |
|3.2.1.1.2.B | |Measurement Ranges |( |Test | |
|3.2.1.1.2.C | |Measurement Ranges |( |Test | |
|3.2.1.1.2.D | |Measurement Ranges |( |Test | |
|3.2.1.1.2.E | |Measurement Ranges |( |Test | |
|3.2.1.1.2.F | |Measurement Ranges |( |Test | |
|3.2.1.1.2.G | |Measurement Ranges |( |Test | |
|3.2.1.1.2.H | |Measurement Ranges |( |Test | |
|3.2.1.1.2.I | |Measurement Ranges |( |Test | |
|3.2.1.1.2.J | |Measurement Ranges |( |Test | |
|3.2.1.1.2.K | |Measurement Ranges |( |Test | |
|3.2.1.1.2.L | |Measurement Ranges |( |Test | |
|3.2.1.1.2.M | |Measurement Ranges |( |Test | |
|3.2.1.1.2.N | |Measurement Ranges |( |Test | |
|3.2.1.1.3.A | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.B | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.C | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.D | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.E | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.F | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.G | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.H | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.I | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.J | |Measurement Accuracies |( |Test | |
|3.2.1.1.3.K | |Measurement Accuracies |( |Test | |
|3.2.1.1.4.A | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.B | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.C | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.D | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.E | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.F | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.G | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.H | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.I | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.J | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.K | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.L | |Measurement Frequencies |( |Test | |
|3.2.1.1.4.M | |Measurement Frequencies |( |Test | |
|3.2.1.1.5 | |Physical Boundaries for Measurement Performance Characteristics |( |Test | |
|3.2.1.1.6.A | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.B | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.C | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.D | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.E | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.F | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.G | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.H | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.I | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.J | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.K | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.L | |Data Storage Frequencies |( |Test | |
|3.2.1.1.6.M | |Data Storage Frequencies |( |Test | |
|3.2.1.1.7.A | |Data Storage Capacity |( |Analysis | |
|3.2.1.1.7.B | |Data Storage Capacity |( |Analysis | |
|3.2.1.1.8 | |Data Storage – Return Logistics |( |Demonstration | |
|3.2.1.1.9 | |Data Downlink |( |Test | |
|3.2.1.1.10 | |Software Update Uplink |( |Test | |
|3.2.1.1.11.A | |Design |( |Demonstration | |
|3.2.1.1.11.B | |Design |( |Demonstration | |
|3.2.1.1.11.C | |Design |( |Demonstration | |
|3.2.1.1.11.D | |Design |( |Demonstration | |
|3.2.1.1.11.E | |Design |( |Test | |
|3.2.1.1.11.F | |Design |( |Certificate of | |
| | | | |Compliance | |
|3.2.1.1.11.G | |Design |( |Inspection | |
|3.2.1.1.11.H.1 | |Design |( |Inspection | |
|3.2.1.1.11.H.2 | |Design |( |Demonstration | |
|3.2.1.1.11.H.3 | |Design |( |Demonstration | |
|3.2.2.1.1 | |VOILA Drawer Mass |( |Test | |
|3.2.2.1.2 | |VOILA Ancillary Hardware Mass |( |Test | |
|3.2.2.1.3 |6.2.1.2.4 |VOILA Drawer Center of Gravity Constraints |( |Test |S683-34510 A |
|3.2.2.2.1.B | |Stowed Envelope and Mass |( |Inspection | |
|3.2.3A |7.2 |Reliability, Quality, and Non-Conformance Reporting |N/A |N/A |Applicable reliability requirements are |
| | | | | |documented in this SRD |
|3.2.3B1 |7.3.1 |Reliability, Quality, and Non-Conformance Reporting |( |Analysis | |
|3.2.3B2 |7.3.1 |Reliability, Quality, and Non-Conformance Reporting |( |Analysis | |
|3.2.3.C1 |7.3.2.1 |Reliability, Quality, and Non-Conformance Reporting |( |Document Review | |
|3.2.3.C2 |7.3.2.2 |Reliability, Quality, and Non-Conformance Reporting |( |Document Review | |
|3.2.3.C3 |7.3.2.3 |Reliability, Quality, and Non-Conformance Reporting |( |Document Review | |
|3.2.3.C4 |7.3.2.4 |Reliability, Quality, and Non-Conformance Reporting |( |Document Review | |
|3.2.3.1 | |Failure Propagation |( |Analysis | |
|3.2.3.2 |3.1.1 |Useful Life |( |Analysis | |
|3.2.3.2.1 | |Operational Life (Cycles) |( |Analysis | |
|3.2.3.2.2 | |Shelf Life |( |Analysis | |
|3.2.3.2.3 | |Limited Life |( |Document Review | |
|3.2.5.1.5B2 |6.3.1.2A |Pressure Rate of Change - Carrier (Orbiter) |( |Analysis | |
|3.2.6.1 |6.3.1.3 |Launch and Landing |( |Analysis | |
|3.2.7.1.2.1 |6.2.1.2.1 |Dimensional Tolerances |( |Inspection |S683-34510 A |
|3.2.7.1.2.2 |6.2.1.2.2 |SIR Drawer Structural/ Mechanical Interfaces |( |Inspection |S683-34510 A |
|3.2.7.1.2.4 | |HRF Rack Seat Track Interfaces |( |Fit Check | |
|3.2.7.2.1.1 |6.2.2.1.1 |SIR Drawer Power Connectors |( |Inspection |S683-34510 A |
|3.2.7.2.1.2 |6.2.2.1.2 |Rack Connector Panel J1 Power Connector |N/A | |S683-34510 A |
|3.2.7.2.2.1 |6.2.2.2.1 |Steady-State Operating Voltage |( |Test |S683-34510 A |
|APPENDIX C |
| |
|FUNCTIONAL PERFORMANCE VERIFICATION MATRIX (Cont’d) |
|HRD Section |LS-71000 |Requirement |Applicable |Verification Method |Comments |
| |Section | | | | |
|3.2.7.2.2.2 |6.2.2.2.2 |Transient Operating Voltage Envelope |( |Test |S683-34510 A |
|3.2.7.2.2.3A |6.2.2.2.3A |Ripple Voltage/Noise Characteristics - Peak to Peak |( |Test |S683-34510 A |
|3.2.7.2.2.3B |6.2.2.2.3B |Ripple Voltage/Noise Characteristics - Spectrum |( |Test |S683-34510 A |
|3.2.7.2.3 |6.2.2.3 |Maximum Current Limit |( |Test |S683-34510 A |
|3.2.7.2.4 |6.2.2.4 |Reverse Current |( |Test |S683-34510 A |
|3.2.7.2.5 |6.2.2.5 |Reverse Energy |( |Test |S683-34510 A |
|3.2.7.2.6 |6.2.2.6 |Capacitive Loads |( |Test |S683-34510 A |
|3.2.7.2.10.1B |6.2.2.7.1B |Wire Derating - Basis |( |Analysis |S683-34510 A |
|3.2.7.3.1.1 |6.2.3.1.1 |SIR Drawer Data Connectors |( |Inspection |S683-34510 A |
|3.2.7.3.1.2 |6.2.3.1.2 |HRF Rack Connector Panel J2 Connector |N/A | |S683-34510 A |
|3.2.7.3.2 |6.2.3.2 |HRF Ethernet Interfaces |N/A | |S683-34510 A |
|3.2.7.3.3 |6.2.3.3 |HRF TIA/EIA-422 Interfaces |N/A | |S683-34510 A |
|3.2.7.3.4 |6.2.3.4 |HRF Bi-Directional Discretes Interfaces |N/A | |S683-34510 A |
|3.2.7.3.5 |6.2.3.5 |HRF Analog Interfaces |( |Test | |
|3.2.7.4.1.1 |6.2.4.1.1 |SIR Drawer Video Interface |N/A | |S683-34510 A |
|3.2.7.3.6.4.1.A | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.B | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.C | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.D | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.E | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.F | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.G | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.H | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.I | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.J | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.K | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.L | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.M | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.N | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.O | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.P | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.1.Q | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.4.2.A | |CSCI External Interface Requirements |( | Test | |
|3.2.7.3.6.4.2.B | |CSCI External Interface Requirements |( | Test | |
|3.2.7.3.6.4.2.C | |CSCI External Interface Requirements |( | Test | |
|3.2.7.3.6.4.2.D | |CSCI External Interface Requirements |( | Test | |
|3.2.7.3.6.4.2.1.1 | |Word/Byte Notations |( |Analysis | |
|3.2.7.3.6.4.2.1.2 | |Data Types |( |Analysis | |
|3.2.7.3.6.4.2.1.3 | |Service Requests |( |Test | |
|3.2.7.3.6.4.6 | |Software Safety Requirements |( |Analysis | |
|3.2.7.3.6.4.8.A | |CSCI Environment Requirements |( |Test | |
|3.2.7.3.6.4.8.B | |CSCI Environment Requirements |( |Test | |
|3.2.7.3.6.4.8.C | |CSCI Environment Requirements |( |Test | |
|3.2.7.3.6.4.9 | |Software Quality Factors |( |Test | |
|3.2.7.3.6.5.1.A | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.5.1.B | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.5.1.C | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.5.1.D | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.5.1.E | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.5.1.F | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.5.1.G | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.5.2 | |CSCI External Interface Requirements |( |Test | |
|3.2.7.3.6.5.2.1.1 | |Word/Byte Notations |( |Analysis | |
|3.2.7.3.6.5.2.1.2 | |Data Types |( |Analysis | |
|3.2.7.3.6.5.2.1.3 | |Service Requests |( |Test | |
|3.2.7.3.6.5.6 | |Software Safety Requirements |( |Analysis | |
|3.2.7.3.6.5.8.A | |CSCI Environment Requirements |( |Test | |
|3.2.7.3.6.5.8.B | |CSCI Environment Requirements |( |Test | |
|3.2.7.3.6.5.8.C | |CSCI Environment Requirements |( |Test | |
|3.2.7.3.6.5.9 | |Software Quality Factors |( |Test | |
|3.2.7.3.6.6.1.A | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.6.1.B | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.6.1.C | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.6.1.D | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.6.1.E | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.6.1.F | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.6.1.G | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.6.1.H | |CSCI Functional and Performance Requirements |( |Test | |
|3.2.7.3.6.6.2 | |CSCI External Interface Requirements |( |Test | |
|3.2.7.3.6.6.2.1.1 | |Word/Byte Notations |( |Analysis | |
|3.2.7.3.6.6.2.1.2 | |Data Types |( |Analysis | |
|3.2.7.3.6.6.2.1.3 | |Service Requests |( |Test | |
|3.2.7.3.6.6.6 | |Software Safety Requirements |( |Analysis | |
|3.2.7.3.6.6.8.A | |CSCI Environment Requirements |( |Test | |
|3.2.7.3.6.6.8.B | |CSCI Environment Requirements |( |Test | |
|3.2.7.3.6.6.8.C | |CSCI Environment Requirements |( |Test | |
|3.2.7.3.6.6.9 | |Software Quality Factors |( |Test | |
|3.2.7.4.1.2 |6.2.4.1.2 |Rack Connector Panel Interface |N/A | |S683-34510 A |
|3.2.7.4.2 |6.2.4.2 |HRF Rack Video Interface Characteristics |N/A | |S683-34510 A |
|3.2.7.5.1.1 |6.2.5.1.1 |HRF Rack MTL Interface Connectors |N/A | | |
|3.2.7.5.2.2A |6.2.5.2.2A |Fan Hardware |( |Inspection |HRF ED-003 |
|3.2.7.5.2.2B |6.2.5.2.2B |Fan Location |( |Inspection |HRF ED-003 |
|3.2.7.5.2.2C |6.2.5.2.2C |Vibration Isolation |( |Inspection |HRF ED-003 |
|3.2.7.5.2.2D |6.2.5.2.2D |Fan Mounting |( |Analysis |HRF ED-003 |
|3.2.7.5.2.2E |6.2.5.2.2E |Fan Operating Voltage |( |Analysis |HRF ED-003 |
|3.2.7.5.2.2F |6.2.5.2.2F |Fan Speed Controller |( |Analysis |HRF ED-003 |
|3.2.7.6.1 |6.2.6.1 |HRF Vacuum Interface Connectors |N/A | |S683-34510 A |
|3.2.7.7.1.1 |6.2.7.1.1 |HRF Rack Nitrogen Interface Connectors |N/A | |S683-34510 A |
|3.3.1.1.1.1A | |Russian Materials Usage Agreement |( |Certificate of | |
| | | | |Compliance | |
|3.3.1.1.1.1B | |Russian Materials Usage Agreement |( |Certificate of | |
| | | | |Compliance | |
|3.3.1.9C | |Locking Wires |( |Certificate of |Payload Safety Review Panel |
| | | | |Compliance | |
|3.3.3.A |7.3.1 |Workmanship |( |Certificate of | |
| | | | |Compliance | |
|3.3.3.B |7.3.1 |Workmanship |( |Certificate of | |
| | | | |Compliance | |
|3.3.5.1.3B | |Mating/Demating of Powered Connectors |( |Safety Package | |
|3.3.6.2.1A |6.4.3.5.1 |Interior Color - Rack Mounted Equipment - Front Panel Color |( |Inspection |HRF ED-001A |
|3.3.6.2.1B |6.4.3.5.1 |Interior Color - Rack Mounted Equipment - Front Panel Finish |( |Inspection |HRF ED-001A |
|3.3.6.2.1C |6.4.3.5.1 |Interior Color - Rack Mounted Equipment - Latches |( |Inspection |HRF ED-001A |
|3.3.6.2.2A |6.4.3.5.2A |Interior Color - Stowed/Deployable Equipment - COTS |( |Inspection |HRF ED-001A |
|3.3.6.2.2B |6.4.3.5.2B |Interior Color - Stowed/Deployable Equipment - Repackaged |( |Inspection |HRF ED-001A |
|3.3.6.2.3 |6.4.3.5.3 |Soft Goods - Color |( |Inspection |HRF ED-001A |
|3.3.8.1.3 |6.2.1.1.2 |First Modal Frequency |( |Test |Derived from SSP 57000, Section 3.1.1.4D |
|3.3.8.2.1 |6.2.2.14 |Batteries |( |Safety Package |Derived from LS-71000, Section 6.2.2.14 |
NOTE: Fill in rows for Section 3.2.7.3.6 per LS-71020 Appendix A.
APPENDIX D
ACCEPTANCE AND QUALIFICATION TEST APPLICABILITY MATRICES
APPENDIX D
TABLE D-1. ACCEPTANCE AND QUALIFICATION TEST APPLICABILITY MATRIX
|HRD SECTION |HRD VERIFICATION |LS-71000 SECTION |REQUIREMENT |APPLICABLE |COMMENTS |
| |SECTION | | | | |
|3.4.1A |4.3.1.1, 4.3.1.2 |5.4.1.1.6.1 and |Thermal Environment Compatibility |( | |
| | |5.4.1.1.6.2 | | | |
|3.4.1B |4.3.1.1, 4.3.1.2 |5.4.1.1.6.1 and |Thermal Environment Compatibility |( | |
| | |5.4.1.1.6.2 | | | |
|3.4.2A |4.3.2.1 |5.4.1.1.2 |Vibration and Sine Sweep |( | |
|3.4.2B |4.3.2.2.1 |5.4.1.1.3.1 |Vibration and Sine Sweep |( | |
|3.4.2C |4.3.2.2.2, 4.3.2.2.3 |5.4.1.1.3.2 and |Vibration and Sine Sweep |( | |
| | |5.4.1.1.3.3 | | | |
|3.4.3 |4.3.3 |5.4.1.3.4 |Functional Acceptance |( | |
|3.4.4 |4.3.4 |5.4.1.1.10 |EEE Parts Control, Selection, and Burn-in |( | |
|3.4.5 |4.3.5 |5.4.1.1.8 |Flammability |( | |
|3.4.6 |4.3.6 |5.4.1.1.9 |Offgassing |( | |
|3.4.7 |4.3.7 |5.4.1.1.4 |Shock |N/A |Transport will be accomplished via |
| | | | | |pacakaging designed to protect |
| | | | | |hardware from excessive shocks rather |
| | | | | |than via a Rack |
|3.4.8 |4.3.8 |5.4.1.1.5 |Bench Handling |( | |
|3.4.9 |4.3.9 |5.4.1.1.1 |Payload Mass |( | |
|3.4.10 |4.3.10 |5.4.1.2.1 |Electromagnetic Compatibility |( | |
TABLE D-1. ACCEPTANCE AND QUALIFICATION TEST APPLICABILITY MATRIX (Cont’d)
|HRD SECTION |HRD VERIFICATION |LS-71000 SECTION |REQUIREMENT |APPLICABLE |COMMENTS |
| |SECTION | | | | |
|3.4.11 |4.3.11 |5.4.1.1.7 |Acoustic Noise |( | |
|3.4.12.1 |4.3.12.1 |5.4.1.1.11.1 |Safety Critical Structure Dimensional Check |( | |
|3.4.12.2 |4.3.12.2 |5.4.1.1.11.2 |Safety Critical Structure Material Certification |( | |
|3.4.13 |4.3.13 |5.4.1.3.1 |Software Acceptance |N/A | |
|3.4.14 |4.3.14 |5.4.1.3.2 |Pre-Delivery Acceptance |( | |
|3.4.15 |4.3.15 |5.4.1.3.3 |Pre-Installation |( | |
TABLE D-2. Non-Critical Hardware Qualification Test Requirements
| | | | | | |SUBJECT RESTRAINT SYSTEM (SRS) | | | |
|COMPONENT |Tracker |VIPER |Chestpack |Cable Set1 |HMD |Restraint Platform |Restraint |Torso Marker |Restraint |
|Type Test |Camera |drawer | | | | |Pole |Plate |Spring |
COMPONENT
Type Test |Tracker Camera |VIPER drawer |Chestpack |Cable Set1 |HMD |Restraint Platform |Restraint Pole |Torso Marker Plate |Restraint Spring |Vest |Joystick |Paddle/ Pushbutton |Subject Camera | |Thermal Cycling 1½ Cycles |( |( |( | |( | | |( | | |( |( |( | |Acceptance Vibration |( |( |( | |E | | | | | |( |( |( | |Functional |( |( |( |( |( |( |( |( |( |( |( |( |( | |Burn-in (72 hr) |( |( |( | |( |( | |( | | |( |( |( | |Safety Critical Structure – Dimensional Check | |( | | | | | | | | | | | | |Safety Critical Structure – Materials Cert | |( | | | | | | | | | | | | |Software Acceptance * |( |( |( |( |( |( | |( | | |( |( |( | |Pre-Delivery Acceptance Functional |( |( |( |( |( |( |( |( |( |( |( |( |( | |
* Lists hardware need to perform software acceptance test.
1 CABLES: W1, VIPER to R2WS cable
W3, VIPER-CODA cable
W4, VIPER-CODA cable
W5, VIPER-SRS platform cable
W6, VIPER-Chest Pack cable
W7, Chest Pack to Torso marker plate cable
W8, Chest Pack to Paddle cable
W9, Chest Pack to SID cable
-----------------------
10 A
15 A
5 A
(10 Hz, 0.35 V rms)
5 Amps
20 A
10 Amps
15 Amps
20 Amps
March 2003
Lyndon B. Johnson Space Center
Houston, Texas 77058
National Aeronautics and
Space Administration
LS-XXXX
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- example quality assurance quality control plan
- tools for all your teaching needs
- aircrewman air combat training continuum
- specifications for two 2 31 cu
- access washington home
- instructions for completing experiment document worksheets
- colorado space grant consortium
- hondata k pro ecu upgrade
- 2003 small off road engine staff report
Related searches
- nature medicine instructions for authors
- cane walking instructions for patients
- email instructions for beginners
- scientific reports instructions for authors
- zicam instructions for use
- nature instructions for authors
- yahoo email instructions for beginners
- nature journal instructions for authors
- tablet instructions for dummies
- instructions for schedule d irs
- instructions for schedule a
- nature communications instructions for authors