AFCI Troubleshooting Card
[Pages:4]AFCI Troubleshooting Card
For both 1- and 2-pole breakers, LED indications will appear for 5 seconds each time the AFCI is turned "ON" and will display each time the beaker is reset for up to 30 days after the last trip. The last known trip condition can cleared by the following process: 1. Turn the AFCI to the "OFF" position. 2. Press and hold Push-to-Test (PTT) button(s). 3. Turn the AFCI to the "ON" position. 4. Release PTT button(s) within 3 seconds.
1-800-333-7421
LED 1 LED 2 Test button
LED 1 LED 2 LED 3 Test buttons
usa.afci
1-Pole CAFCI Circuit Breaker
LED indicators Last known
1
2
trip condition Troubleshooting
Off
Off
Overcurrent
Ensure current on the circuits does not exceed the current rating for the breaker.
On Off Arc fault
Check wiring for the parallel and series arc faults. Check devices for series arc faults. Use Intelli-Arc to assist and accelerate diagnosis.
Check wiring, switches, and receptacles for possible
On
On
Arc fault to ground leakage. Use Intelli-Arc or circuit tester
ground
to troubleshoot. Using safe electrical practices,
systematically identify the source of the ground fault.
2-Pole CAFCI Circuit Breaker
LED indicators Last known
1 2 3 trip condition Troubleshooting
Off Off Off Overcurrent
Ensure current on the circuits does not exceed the current rating for the breaker.
On
Off
Off
Arc fault (leg A)
Off
Off
On
Arc fault (leg B)
On
On
On
Arc fault to ground
Check wiring for the parallel and series arc faults. Check devices for series arc faults. Use Intelli-Arc to assist and accelerate diagnosis.
Check wiring, switches, and receptacles for possible ground leakage. Use Intelli-Arc or circuit tester to troubleshoot. Using safe electrical practices, systematically identify the source of the ground fault.
Tips and Tricks Route wires in strategic areas so homeowners and other trades are less likely to pierce through a wire. If possible, perform work after the other trades, i.e. HVAC and plumbing, have completed. Wire receptacles around the screw instead of backstabbing. Use properly maintained tools, i.e. sharp blades. Ensure a tight connection between light sockets and light bulb bases. Do not overload circuit with excessive amounts of electronics. Affirm furniture is not on or pushing against electrical wires. Watch for blackened plugs, very damaged wires, or noisy electronics. Electronics should be Underwriters Laboratories (UL) listed, or equivalent, and comply with part 15 of Federal Communications Commission (FCC) regulations. Protect electronics on surge protectors.
The PTT button is the only method recommended to verify the functionality of the AFCIs by National Electrical Manufacturers Association (NEMA) and UL.
Test AFCIs once per month to ensure proper working conditions.
RPMR-COMBO-0218
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- arc fault circuit interrupters frequently asked
- troubleshooting an enphase installation
- energybar 832 user guide neptune systems
- afci troubleshooting card
- electrical safety nfpa 70e
- basic troubleshooting instructions dge
- outlets not working strada electric
- maintenance how to s
- how to reset a breaker or gfi gfic loss power a
- psu electrical safety program
Related searches
- small engine troubleshooting guide
- free troubleshooting car problems
- troubleshooting car problems
- spectrum cable troubleshooting guide
- auto troubleshooting free questions
- car troubleshooting questions
- diesel engine troubleshooting pdf
- troubleshooting car alarm problems
- troubleshooting small honda gas engines
- troubleshooting electronic components pdf
- troubleshooting electronic circuits pdf
- electronics troubleshooting techniques pdf