LAYOUT DRAFTING & PATTERN MAKING
[Pages:121]Layout Drafting & Pattern Making for Insulators
_________________________________
LAYOUT DRAFTING & PATTERN MAKING
FOR HEAT & FROST INSULATORS
Hans Siebert
APPRENTICE WORK BOOK
& JOURNEYMAN REVIEW MANUAL
Hans Siebert-2000
_________________________________
Page 1
Layout Drafting & Pattern Making for Insulators
Preface
This book has been prepared as a text for use in Heat and Frost Insulator apprenticeship classes. It explains basic methods of drawing patterns for developing sheet metal and other types of protective covers commonly produced for wrap over insulation. The book does not attempt to teach field work-practices or any application methods used in the trade. Learning how to crimp, bead, seam, rivet and apply materials is best accomplished on the job, not from studying a book. However, for the limited purpose of pattern development, this book meets every requirement of an apprenticeship textbook and is, in addition, also well adapted for reference use by journeymen, foremen, and pre-fabrication workers engaged in the designing and/or laying out patterns.
The instructions are easy to follow with numerous practical problems that can be completed straightforwardly and worked without elaborate collections of tools or equipment. The subject-matter deals with common trade problems and the specific methods of presenting the assignments are the result of many years of teaching in apprenticeship classes as well as practical experience gained in the asbestos worker trade.
The format of the book assumes sequential completion of tasks, especially regarding the preparatory work of practicing drawing principles. For the novice, later work in the book assumes knowledge gained in prior effort. For students with prior knowledge many of the projects can be completed without a drawn-out effort on the study of groundwork.
The descriptions are clear and well organized and step-by-step. They stimulate the student to think and reason on his or her own volition as well as simplify the instructor's participation. The work is so planned that the student can work through assignments without arduous direction and tedious supervision. Numerous illustrative problems are distributed throughout the text. The selected assignments and examples are representative of the kind of problems a worker faces on the job and they serve to enable the mechanic to apply knowledge to new-fangled and uncommon situations.
Finally, no new material is to be found in this book. Although, I have drawn all illustrations myself, the described projects have been scraped together from various sources in the building trades, including from manuscripts and books used in the asbestos workers, sheet metal workers and ironworkers trades. Additionally, ideas for the projects have been collected from apprenticeship programs throughout the industry. Any and all such contributions are thankfully acknowledged.
Hans Siebert October 2000
Page 2
Layout Drafting & Pattern Making for Insulators
Table of Contents
Drawing Principles
Equipment, Tools, Preparations
5
Practice Problems in Drawing
Bisect Straight Line
8
Erect Perpendiculars
9
Erect Perpendiculars (Method 2)
10
Erect Perpendiculars (Method 3)
11
Draw Parallel Line
12
Circle Properties
13
Draw Tangent
14
Bisect Angle
15
Draw Equilateral Triangle
16
Copy an Angle
17
Copy a Triangle
18
Copy an Irregular Figure
19
Construct a Square with Side Given
20
Construct a Pentagon (Method 1)
21
Construct a Pentagon (Method 2)
22
Construct a Hexagon
23
Construct an Octagon (Method 1)
24
Construct an Octagon (Method 2)
25
Construct an Octagon (Method 3)
26
Draw a Circle Through Points
27
Find Center of Circle
28
Describe Segment of Circle
29
Inscribe Triangle into Circle
30
Inscribe Circle into Triangle
31
Draw an Ellipse
32
Draw an Approximate Ellipse
33
Draw an Approximate Ellipse (Method 2)
34
Draw an Ellipse by Intersecting Lines
35
Draw an Egg-shaped Oval
36
Draw an Ellipse with Pencil and Thread
37
Draw a Parabola
38
Draw a Hyperbola
39
Draw a Spiral
40
Draw a Helix
41
Divide a Straight Line into Equal Parts (Method 1)
42
Divide a Straight Line into Equal Parts (Method 2)
43
Continued
Page 3
Layout Drafting & Pattern Making for Insulators
Practice Problems in Pattern Development
Introduction to Developments Closed Box Open Box Square Prism Tetrahedron Octahedron Dodecahedron Icosahedron Dovetail Seam Metal Over Tees (Field Method) Non-reducing Tee Layout 90-Degree Bend Gores for Bends (Field Method) Gores for Bends (Development Method) Gores for Bends (Analytical Method) Non-reducing Lateral at any Angle Reducing Tee at 90 Degrees Reducing Lateral at any Angle Cone Truncated Cone (Transition) Spheres Lunes for Spheres (Head Gores) Lunes for Spherical Tank Head Cylindrical Tank with Rounded Head (Analytical Method) Rounded Head Lunes (Shortcut Method) Round Taper (Off Center) Round Taper (One Side Straight) 35-Degree Conical End Cap Square to Square Square to Round Butterfly Layout
Table of Decimal to Fraction Conversions
Table of Natural Trigonometric Functions
Practice Problems for Advanced Studies
44 45 46 47 48 49 50 51 52 53 55 57 59 64 65 73 75 77 79 81 83 84 86 88 91 92 93 94 95 97 99
100
101
103-121
Page 4
Layout Drafting & Pattern Making for Insulators
Geometric Construction
DRAWING PRINCIPLES
DRAWING EQUIPMENT
Equipment. The following list comprises the equipment required for a course in sheet-metal pattern drafting: Drawing board, 24" x 30", T-square, 30"; 45 ? triangle, 10"; 30? x 60? triangle, 10"; architect's scale, 12"; 4H drawing pencil; pencil erasing rubber; thumb tacks; detail paper; also a set of drawing instruments consisting of the following items: 5" dividers, 5 1/2" compasses, 3" bow spacers, 3" bow pencil, ruling pen, bow pen and irregular curves.
Paper. The paper generally used for sheet-metal pattern drafting is known as brown detail paper. However, for finished drawings, white craft paper is more suitable. It can be bought of almost any width, in large or small rolls, and is sold by the yard or pound. The paper should be of medium thickness, very strong and tough, because a shop drawing is likely to be subjected to considerable rough usage.
Pencils. For working drawings, full size details, etc., on craft paper, a 4H pencil is quite satisfactory. For developing miter patterns in which the greatest accuracy is required, a 5H pencil is generally used. The accuracy of drawings depends, in a great measure, upon the manner in which the pencils are sharpened. To sharpen the pencil, remove the wood from both ends by means of a sharp knife, exposing about 3/8" of lead. One end should then be sharpened to a round point, and the other to a chisel point or a wedge-shaped end. This operation should be done with a fine file or pencil sharpener. For example, a strip of No. 0 sandpaper, 4" long and 3/4" wide, glued to a thin strip of wood, is quite serviceable. The chisel end of the pencil is used for drawing straight lines, and the conical point for free-hand sketching and marking dimensions. A soft pencil should never be used for drawing, because it becomes dull after drawing just a few lines. Soft pencils make it difficult to draw fine, sharp lines and to keep the paper clean.
Preparation of the Paper. The paper is fastened to the board with thumb-tacks. Care must be taken to have it lie perfectly flat on the board, so that it will create no wrinkles. To do this, proceed as follows: Place the long edge of the paper parallel with the long edge of the board, the paper being within about three inches of the lower and left-hand edge of the board. Insert a thumb-tack in the upper right-hand
Page 5
Layout Drafting & Pattern Making for Insulators
corner and press it in until it is flush with the surface of the paper. Next, place the left hand on the paper near the upper right-hand corner; then slide the hand toward the lower left-hand corner, removing all wrinkles, and insert a thumb tack as before. Lay the left hand on the middle of the sheet and slide it toward the upper left-hand corner; holding it there, press in the third tack. Slide the hand from the center of the paper toward the lower right-hand corner, and insert the fourth tack. This completes the operation.
PRACTICAL GEOMETRY In presenting this subject to the student, no attempt has been made to give a complete course in geometry. Rather, the selected problems are chosen to be of the greatest assistance to the pattern draftsman. They are composed of examples that are used in every-day practice and are arranged in a logical order.
Practical geometry is the science of geometry adapted to practical purposes. Theoretical demonstrations have been omitted. Every student, whose aim it is to become a proficient pattern draftsman, should have a fair knowledge of the subject. The problems on these pages should be carefully studied and worked with great accuracy, as the technical skill acquired in the use of the drawing instruments will be of great value in later work.
Geometrical Problems When the problems herein given have been carefully studied, draw each problem, completing each step in the construction before proceeding to the next. All lines should be as sharp and fine to be consistent with clearness.
It is best to work the assignments in a sequential order because some of the later projects assume knowledge of skills, that have been mastered in preceding attempts.
In the geometrical figures, except for occasional deviations, the given and required lines are shown in full heavy lines, and the construction in full light lines. The drawings on the instruction sheets do not always exactly reflect the specified dimensions, however, the distances within a drawing are proportional to them. This is due to the fact that drawings, manipulated on the sheets by a word processor, have been adjusted to conform to space limitations. Nevertheless, the assignments, when drawn, should reflect the exact dimensions stated in the problems.
Preparation of Plates. The size of paper recommended for the problems of this course is 15" x 20". The size of each plate is to be 14" x 18", having a border-line all around 1/2" from the edge of the plate, leaving the space inside of the border line 13" x 17".
Page 6
Layout Drafting & Pattern Making for Insulators
Divide the plate into two equal parts by means of a horizontal line. Using the scale, divide the length of plate into three equal parts, as shown by the vertical lines. This divides the drawing plate into six rectangular spaces. The problems should be drawn as near the center of each space as possible. See the following example in Fig. 0:
D g
f
A
e
75 46
1
3
C
h
n
o
m
B
12
10 9
11
8
2
E
C
m
D
5
5
4 3
4 3
4
3
2
2
n
1
A
2
3
4
5
1
B
B
D
1 A2
A'
5
6
C
8 B 7
6
D 1
2
A
C
3
4
C
5 E
3
2
4
E
1
A
B
4 1
F C
E D
A
3
G
2
B
HS2000
Fig. 0 EXAMPLE OF COMPLETED SET OF DRAWINGS
Page 7
Layout Drafting & Pattern Making for Insulators
Practice Problems in Drawing
N 2
1O A 2
1 M
FIG. 1
HS2000
Fig. 1. To bisect a straight line MN, or the arc of a circle MON. Let MN 3-1/4 inches long be the given line, which it is required to bisect. With centers M and N, and any radius greater than one-half of MN, describe the arcs 1 and 2. Through the points of intersection of these arcs draw a line, and the points of intersection with the given line MN, and the arc MON, shown by OA will give the required points.
Page 8
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- drafting a business plan sample
- letter drafting samples
- letter drafting format
- drafting letters to avoid
- letter drafting in english
- drafting a professional letter
- drafting letter guide
- contract drafting sample
- drafting lettering guidelines
- drafting lettering font
- contract drafting training
- sheet metal pattern layout methods