Www.lcps.org
Understanding How to Read, Measure and Analyze DataSignificant Figures"Lesson 4: Measurement." Lesson 4: Measurement. N.p., n.d. Web. 20 Sept. 2013.IntroductionIf you have not had much experience in a lab, you are probably used to thinking of numbers as absolutes.? When a recipe calls for 3 eggs, you put in precisely 3 eggs, not 3.1 or 2.8.? If I ask how many fingers you have, you would answer "10", not "9.75" or "10.1". However, in the laboratory, most numbers are the result of measurements.? Any number resulting from measurement is not an absolute number, since it is only as exact as the measuring device can register.? For example, when you use a thermometer to measure air temperature, you cannot know what the absolute temperature is.? Instead, you can measure the air temperature to the nearest degree.? Using the thermometer below, for example, you might measure the temperature to be 66°F.? However, the absolute temperature might be 65.681290°F.We use significant figures to show how many of the digits in a number were measured and how many of them were just guessed or rounded off.? Significant figures are the digits in a number which are known precisely, plus one estimated digit.? In our temperature example, we are sure that the temperature is somewhere in the 60's, so the first "6" is a measured number and is a significant figure.? The second "6" is an estimate, so it is also a significant figure.? In our flow example from the last section, we were only sure of the initial "5".? All of the trailing zeroes are merely place-keepers which were not measured or estimated, so 500,000 has only one significant figure.?Rules for Significant FiguresRules:Examples (# of Significant Figures):All non-zero numbers are significant.?251313.494Zeroes between significant digits are significant3053420035If there is no decimal point, then trailing zeroes are not significant.?4702101If there is a decimal point, then all trailing zeroes are significant.41.00410.2If a number is less than one, then the first significant figure is the first non-zero digit after the decimal point.? 0.00910.010604Addition/Subtraction Problems: Your calculated value will have the same number of digits to the right of the decimal point as that of the least precise quantity.This is what your calculator spits out: 7.939 + 6.26 + 11.1 = 25.299 What is your final answer? __________Multiple/Division Problems: The number of sig figs in the final calculated value will be the same as that of the quantity with the fewest number of sig figs used in the calculation.This is what your calculator spits out: (27.2 x 15.63) / 1.846 = 230.3011918What is your final answer? __________Combined addition/subtraction and multiplication/division: First apply the rules for addition/subtraction, and then apply the rules for multiplication/division.Practice ProblemsProvide the number of significant figures (sig figs) in each of the following numbers:0.00000055 g _______(c) 1.6402 g _______(e) 16502 g _______3.40 x 103 mL _______(d) 1.020 L _______(f) 1020 L _______Perform the operation and report the answer with the correct number of significant figures (sig figs):(10.3) x (0.01345) = __________(b) (10.3) + (0.01345) = __________[(10.3) + (0.01345)] / [(10.3) x (0.01345)] = __________Accurate versus Precise Measurements"Accuracy and Precision." Accuracy and Precision. N.p., n.d. Web. 23 Sept. 2013: Is how close a measured value is to the actual (true) value.Precision: Is how close the measured values are to each other.Example of Precision and Accuracy:__________ Accuracy__________ Precision__________ Accuracy__________ Precision__________ Accuracy__________ PrecisionSo, if you are playing soccer and you always hit the left goal post instead of scoring, then you are not accurate, but you are precise!Bias (don't let precision fool you!)If you measure something several times and all values are close, they may all be wrong if there is a "Bias"Bias is a systematic (built-in) error which makes all measurements wrong by a certain amount.Examples of BiasThe scales read "1 kg" when there is nothing on themYou always measure your height wearing shoes with thick soles.A stopwatch that takes half a second to stop when clickedIn each case all measurements will be wrong by the same amount. That is bias.Degree of AccuracyAccuracy depends on the instrument you are measuring with. But as a general rule: The degree of accuracy is half a unit each side of the unit of measure Examples:If your instrument measures in "1"s then any value between 6? and 7? is measured as "7"If your instrument measures in "2"s then any value between 7 and 9 is measured as "8" ................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- https www municipalonlinepayments
- bcps org jobs
- lcps frontline oasys
- smartcu org sign on page
- aarp org membership card registration
- free org email accounts
- hackensackumc org pay bill
- get my transcripts org from college
- bcps org community volunteer info
- my access tgh org portal
- bcps org employee self service
- intranet florida hospital org employee