1.1.5.Ab Circuit Theory : Simulation
Activity 1.1.5b Circuit Theory: SimulationIntroductionAs much fun as it is to analyze circuits by hand, the process becomes tedious as circuits grow in size and complexity. This is where Circuit Design Software (CDS) comes to the rescue. As the name implies, the CDS is a software tool that can be used to enter and simulate analog and digital circuit designs. As with most computer applications, the CDS handles the mundane and repetitive tasks associated with analyzing circuits, allowing the designer (you) to concentrate on producing quality and creative designs. In this activity you will gain experience using the Circuit Design Software to analyze simple analog circuits. In future activities we will use the CDS to analyze digital circuits as well. The circuits analyzed are some of the same circuits that were analyzed by hand in Activity 1.2.2. Thus, the theoretical and simulation results can be compared.Series CircuitParallel CircuitEquipment CalculatorCircuit Design Software (CDS)ProcedureShown below is the schematic for a simple series circuit. Analyze this circuit to determine its total current and the voltage across each of the two resistors. To make these measurements, add an ammeter and two voltmeters. The second schematic shown is the original circuit with the added meters. Calculated Values: VR1=3.74VVR2=7.99V IT=17mV Using the CDS, enter and simulate this circuit. Measure and record the circuit’s total current and the voltage across each of the resistors. Measured Values: Using the CDS, analyze the circuit shown below to determine IT, VR1, VR2, & VR3. Add the appropriate ammeters and voltmeters. Be sure to put your answer in proper engineering notation and use the correct units. This circuit was analyzed by hand in Activity 1.2.2. How do these measured values compare to the previously calculated values? If they do not match, review your circuit, your calculations, and make any necessary corrections.They Match Perfectly.Using the CDS, analyze the circuit shown below to determine IT, VR1, VR2, VR3, & VR4.Do the measured values compare to your previously calculated values in Activity 1.2.2? The Values Where very close.Using the CDS, analyze the circuit shown below to determine IT, IR1, IR2, & IR3. Do the measured values compare to your previously calculated values in Activity 1.2.2?The Values Where very close. Using the CDS, analyze the circuit shown below to determine IT, IR1, IR2, IR3, & IR4. Do the measured values compare to your previously calculate values in Activity 1.2.2?The Values Where very close. ConclusionIt should be obvious that using a CDS to analyze circuits is far easier than performing the calculations by hand. Yet, being able to perform these calculations by hand is still an important skill for a circuit designer. Why?The Computer will not always be there for you to use and knowing them by hand helps you calculate anything you want even without a computer.Using the results from step (3) of the procedure, verify Kirchhoff’s Voltage Law.SeriesVT= V1+V2+V3….Using the results from step (5) of the procedure, verify Kirchhoff’s Current Law.ParallelVT=V1=V2=V3=…. ................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- how to calculate safety distances stability technology inc
- circuits worksheet
- circuits phet lab
- activity 1 2 3 circuit theory simulation
- activity 2 1 4 aoi logic analysis hines james home
- 1 1 circuit theory simulation
- spirit 2 university of nebraska lincoln
- activity 1 2 4 circuit calculation
- calculators in circuit analysis ed thelen
- 1 1 5 a circuit theory hand calculations
Related searches
- electronic devices and circuit theory pdf
- 1 1 5 ratio chart
- circuit theory equations
- 1 1 5 a circuit theory hand calculations answer
- minecraft pocket edition 1 1 5 apk
- 1 or 3 2 0 5 374 374 168 1 1 default username and password
- 1 or 3 2 0 5 711 711 168 1 1 default username and password
- 1 or 3 2 0 5 693 693 168 1 1 default username and password
- 1 or 3 2 0 5 593 593 or 2dvchrbu 168 1 1 default username and password
- 1 or 3 2 0 5 910 910 168 1 1 default username and password
- 1 or 3 2 0 5 364 364 168 1 1 admin username and password
- 192 1 or 3 2 0 5 33 33 1 1 default username and password