Florida Building
Florida Supplement to the 2012 IBC
Chapters 1-35 (Excluding HVHZ and Florida Specific Chapter 4 Requirements)
PRE-GLITCH CORRECTION VERSION
Note 1: Throughout the document, change International Building Code to Florida Building Code, Building; change the ICC Electrical Code to Chapter 27 of the Florida Building Code, Building; change the International Energy Conservation Code to the Florida Building Code, Energy Conservation; change the International Existing Building Code to Florida Building Code, Existing Building; change the International Fire code to Florida Fire Prevention Code; change International Fuel Gas Code to Florida Building Code, Fuel Gas; change the International Mechanical Code to Florida Building Code, Mechanical; change the International Plumbing Code to Florida Building Code, Plumbing; change the International Residential Code to Florida Building Code, Residential.
Chapter 1 – Scope and Administration
Section 101 – General
Change Section 101 to read as follows:
101.1 Title. These regulations shall be known as the Florida Building Code, hereinafter referred to as “this code.”
101.2 Scope. (No Change)
Exceptions:
1. Detached one- and two-family dwellings and multiple single-family dwellings and multiple single-family dwellings (town houses) not more than three stories above grade plane in height with a separate means of egress and their accessory structures shall comply with the International Residential Code Florida Building Code, Residential.
2. Existing buildings undergoing repair, alterations or additions and change of occupancy shall comply with Chapter 34 of this code.
101.2.1 Appendices. (No Change)
101.3 Intent. (No Change)
101.4 Referenced codes. The other codes listed in Sections 101.4.1 through 101.4.6 8 and referenced elsewhere in this code shall be considered part of the requirements of this code to the prescribed extent of each such reference.
101.4.1-101.4.3 (No Change)
101.4.4 Property maintenance. The provisions of the International Property Maintenance Code shall apply to existing structures and premises; equipment and facilities; light, ventilation, space heating, sanitation, life and fire safety hazards; responsibilities of owners, operators and occupants; and occupancy of existing premises and structures. Reserved.
101.4.5 Fire prevention. The provisions of the International Fire Code For provisions related to fire prevention, refer to the Florida Fire Prevention Code. The Florida Fire Prevention Code shall apply to matters affecting or relating to structures, processes and premises from the hazard of fire and explosion arising from the storage, handling or use of structures, materials or devices; from conditions hazardous to life, property or public welfare in the occupancy of structures or premises; and from the construction, extension, repair, alteration or removal of fire suppression, automatic sprinkler systems and alarm systems or fire hazards in the structure or on the premises from occupancy or operation.
101.4.6 (No Change)
101.4.7 Accessibility. For provisions related to accessibility, refer to the Florida Building Code, Accessibility.
101.4.8 Manufactured buildings. For additional administrative and special code requirements, see section 458, Florida Building Code, Building, and Rule 61-41 F.A.C.
(Mod CA4952 – R2 / AM)
Section 102 – Applicability
Add Section 102.1.1 to read as follows:
102.1.1 The Florida Building Code does not apply to, and no code enforcement action shall be brought with respect to, zoning requirements, land use requirements and owner specifications or programmatic requirements which do not pertain to and govern the design, construction, erection, alteration, modification, repair or demolition of public or private buildings, structures or facilities or to programmatic requirements that do not pertain to enforcement of the Florida Building Code. Additionally, a local code enforcement agency may not administer or enforce the Florida Building Code, Building to prevent the siting of any publicly owned facility, including, but not limited to, correctional facilities, juvenile justice facilities, or state universities, community colleges, or public education facilities, as provided by law.
(Mod CA4986 / AS)
Section 102 – Applicability
Change Section 102 to read as follows:
102.2 Other Laws. Building. The provisions of this code shall not be deemed to nullify any provisions of local, state or federal law. The provisions of the Florida Building Code shall apply to the construction, erection, alteration, modification, repair, equipment, use and occupancy, location, maintenance, removal and demolition of every public and private building, structure or facility or floating residential structure, or any appurtenances connected or attached to such buildings, structures or facilities. Additions, alterations, repairs and changes of use or occupancy group in all buildings and structures shall comply with the provisions provided in Chapter 34 of this code. The following buildings, structures and facilities are exempt from the Florida Building Code as provided by law, and any further exemptions shall be as determined by the legislature and provided by law:
(a) Building and structures specifically regulated and preempted by the federal government.
(b) Railroads and ancillary facilities associated with the railroad.
(c) Nonresidential farm buildings on farms.
(d) Temporary buildings or sheds used exclusively for construction purposes.
(e) Mobile or modular structures used as temporary offices, except that the provisions of Part II (Section 553.501-553.513, Florida Statutes) relating to accessibility by persons with disabilities shall apply to such mobile or modular structures.
(f) Those structures or facilities of electric utilities, as defined in Section 366.02, Florida Statutes, which are directly involved in the generation, transmission, or distribution of electricity.
(g) Temporary sets, assemblies, or structures used in commercial motion picture or television production, or any sound-recording equipment used in such production, on or off the premises.
(h) Chickees constructed by the Miccosukee Tribe of Indians of Florida or the Seminole Tribe of Florida. As used in this paragraph, the term “chickee” means an open-sided wooden hut that has a thatched roof of palm or palmetto or other traditional materials, and that does not incorporate any electrical, plumbing, or other nonwood features.
(i) Family mausoleums not exceeding 250 square feet in area which are prefabricated and assembled on site or preassembled and delivered on site and have walls, roofs, and a floor constructed of granite, marble, or reinforced concrete.
(j) Temporary housing provided by the Department of Corrections to any prisoner in the state correctional system.
(k) A building or structure having less than 1,000 square feet which is constructed and owned by a natural person for hunting and which is repaired or reconstructed to the same dimension and condition as existed on January 1, 2011, if the building or structure:
1. Is not rented or leased or used as a principal residence;
2. Is not located within the 100-year floodplain according to the Federal Emergency Management Agency’s current Flood Insurance Rate Map; and
3. Is not connected to an off-site electric power or water supply.
102.2.1 – 102.2.6. Add to read as follows:
102.2.1 In addition to the requirements of Section 553.79 and 553.80, Florida Statutes, facilities subject to the provisions of Chapter 395, Florida Statutes, and Part II of Chapter 400, Florida Statutes, shall have facility plans reviewed and construction surveyed by the state agency authorized to do so under the requirements of Chapter 395, Florida Statutes, and Part II of Chapter 400, Florida Statutes, and the certification requirements of the federal government.
102.2.2 Residential buildings or structures moved into or within a county or municipality shall not be required to be brought into compliance with the state minimum building code in force at the time the building or structure is moved, provided:
1. The building or structure is structurally sound and in occupiable condition for its intended use;
2. The occupancy use classification for the building or structure is not changed as a result of the move;
3. The building is not substantially remodeled;
4. Current fire code requirements for ingress and egress are met;
5. Electrical, gas and plumbing systems meet the codes in force at the time of construction and are operational and safe for reconnection; and
6. Foundation plans are sealed by a professional engineer or architect licensed to practice in this state, if required by the Florida Building Code, Building for all residential buildings or structures of the same occupancy class.
102.2.3 The building official shall apply the same standard to a moved residential building or structure as that applied to the remodeling of any comparable residential building or structure to determine whether the moved structure is substantially remodeled. The cost of the foundation on which the moved building or structure is placed shall not be included in the cost of remodeling for purposes of determining whether a moved building or structure has been substantially remodeled.
102.2.4 This section does not apply to the jurisdiction and authority of the Department of Agriculture and Consumer Services to inspect amusement rides or the Department of Financial Services to inspect state-owned buildings and boilers.
102.2.5 Each enforcement district shall be governed by a board, the composition of which shall be determined by the affected localities.
1. At its own option, each enforcement district or local enforcement agency may adopt rules granting to the owner of a single-family residence one or more exemptions from the Florida Building Code relating to:
a. Addition, alteration, or repairs performed by the property owner upon his or her own property, provided any addition or alteration shall not exceed 1,000 square feet or the square footage of the primary structure, whichever is less.
b. Addition, alteration, or repairs by a nonowner within a specific cost limitation set by rule, provided the total cost shall not exceed $5,000 within any 12-month period.
c. Building and inspection fees.
2. However, the exemptions under subparagraph 1 do not apply to single-family residences that are located in mapped flood hazard areas, as defined in the code, unless the enforcement district or local enforcement agency has determined that the work, which is otherwise exempt, does not constitute a substantial improvement, including the repair of substantial damage, of such single-family residences.
3. Each code exemption, as defined in sub-subparagraphs 1a, 1b, and 1c shall be certified to the local board 10 days prior to implementation and shall only be effective in the territorial jurisdiction of the enforcement district or local enforcement agency implementing it.
102.2.6 This section does not apply to swings and other playground equipment accessory to a one- or two-family dwelling.
Exception: Electrical service to such playground equipment shall be in accordance with Chapter 27 of this code.
(Mod CA4988 – R1 / AM)
Section 102 – Applicability
Change Section 102.5 to read as follows:
102.5 Partial invalidity. In the event that any part or provision of this code is held to be illegal or void, this shall not have the effect of making void or illegal any of the other parts or provisions. Reserved.
(Mod CA4992 – R1 / AM)
Section 102 – Applicability
Change Section 102.6 to read as follows:
102.6 Existing structures. The legal occupancy of any structure existing on the date of adoption of this code shall be permitted to continue without change, except as is specifically covered in this code, the International Property Maintenance Code or the International Fire Code, the Florida Fire Prevention Code, or as is deemed necessary by the building official for the general safety and welfare of the occupants and the public.
(Mod CA4994 – R1 / AM)
Section 102 – Applicability
Change Section 102.7 to read as follows:
102.7 Relocation of manufactured buildings.
(1) Relocation of an existing manufactured building does not constitute an alteration.
(2) A relocated building shall comply with wind speed requirements of the new location, using the appropriate wind speed map. If the existing building was manufactured in compliance with the Standard Building Code (prior to March 1, 2002), the wind speed map of the Standard Building Code shall be applicable. If the existing building was manufactured in compliance with the Florida Building Code (after March 1, 2002), the wind speed map of the Florida Building Code shall be applicable.
(3) A relocated building shall comply with the flood hazard area requirements of the new location, if applicable.
(Mod SP 5254 / AS)
Section 102 – Applicability
Add Section 102.8 to read as follows:
102.8 Existing mechanical equipment. An agency or local government may not require that existing mechanical equipment on the surface of a roof be installed in compliance with the requirements of the Florida Building Code until the equipment is required to be removed or replaced.
(Mod CA 4997 – R1 / AM)
Section 103 – Department of Building Safety
Change Section 103 to read as follows:
SECTION 103
DEPARTMENT OF BUILDING SAFETY
RESERVED
103.1 Creation of enforcement agency.
The Department of Building Safety is hereby created and the official in charge thereof shall be known as the building official.
103.2 Appointment.
The building official shall be appointed by the chief appointing authority of the jurisdiction.
103.3 Deputies.
In accordance with the prescribed procedures of this jurisdiction and with the concurrence of the appointing authority, the building official shall have the authority to appoint a deputy building official, the related technical officers, inspectors, plan examiners and other employees. Such employees shall have powers as delegated by the building official. For the maintenance of existing properties, see the International Property Maintenance Code.
(Mod CA4991- R1 / AM)
Section 104 - Duties and Powers of Building Official
Change Section 103 to read as follows:
104.1 General. The building official is hereby authorized and directed to enforce the provisions of this code. The building official shall have the authority to render interpretations of this code and to adopt policies and procedures in order to clarify the application of its provisions. Such interpretations, policies and procedures shall be in compliance with the intent and purpose of this code. Such policies and procedures shall not have the effect of waiving requirements specifically provided for in this code. Reserved.
104.2 Applications and permits. The building official shall receive applications, review construction documents and issue permits for the erection, and alteration, demolition and moving of buildings and structures, inspect the premises for which such permits have been issued and enforce compliance with the provisions of this code. Reserved.
104.3 Notices and orders. The building official shall issue all necessary notices or orders to ensure compliance with this code. Reserved.
104.4 Inspections. The building official shall make all of the required inspections, or the building official shall have the authority to accept reports of inspection by approved agencies or individuals. Reports of such inspections shall be in writing and be certified by a responsible officer of such approved agency or by the responsible individual. The building official is authorized to engage such expert opinion as deemed necessary to report upon unusual technical issues that arise, subject to the approval of the appointing authority. Reserved.
104.5 Identification. The building official shall carry proper identification when inspecting structures or premises in the performance of duties under this code. Reserved.
104.6 Right of entry. Where it is necessary to make an inspection to enforce the provisions of this code, or where the building official has reasonable cause to believe that there exists in a structure or upon a premises a condition which is contrary to or in violation of this code which makes the structure or premises unsafe, dangerous or hazardous, the building official is authorized to enter the structure or premises at reasonable times to inspect or to perform the duties imposed by this code, provided that if such structure or premises be occupied that credentials be presented to the occupant and entry requested. If such structure or premises is unoccupied, the building official shall first make a reasonable effort to locate the owner or other person having charge or control of the structure or premises and request entry. If entry is refused, the building official shall have recourse to the remedies provided by law to secure entry. Reserved.
104.7 Department records. The building official shall keep official records of applications received, permits and certificates issued, fees collected, reports of inspections, and notices and orders issued. Such records shall be retained in the official records for the period required for retention of public records. Reserved.
104.8 Liability. The building official, member of the board of appeals or employee charged with the enforcement of this code, while acting for the jurisdiction in good faith and without malice in the discharge of the duties required by this code or other pertinent law or ordinance, shall not thereby be rendered liable personally and is hereby relieved from personal liability for any damage accruing to persons or property as a result of any act or by reason of an act or omission in the discharge of official duties. Any suit instituted against an officer or employee because of an act performed by that officer or employee in the lawful discharge of duties and under the provisions of this code shall be defended by legal representative of the jurisdiction until the final termination of the proceedings. The building official or any subordinate shall not be liable for cost in any action, suit or proceeding that is instituted in pursuance of the provisions of this code. Reserved.
104.9 Approved materials and equipment. (No change)
104.10 Modifications. Wherever there are practical difficulties involved in carrying out the provisions of this code, the building official shall have the authority to grant modifications for individual cases, upon application of the owner or owner’s representative, provided the building official shall first find that special individual reason makes the strict letter of this code impractical and the modification is in compliance with the intent and purpose of this code and that such modification does not lessen health, accessibility, life and fire safety, or structural requirements. The details of action granting modifications shall be recorded and entered in the files of the department of building safety. Reserved.
104.10.1 Flood hazard areas. The building official shall not grant modifications to any provision required in flood hazard areas as established by Section 1612.3 unless a determination has been made that:
1. A showing of good and sufficient cause that the unique characteristics of the size, configuration or topography of the site render the elevation standards of Section 1612 inappropriate.
2. A determination that failure to grant the variance would result in exceptional hardship by rendering the lot undevelopable.
3. A determination that the granting of a variance will not result in increased flood heights, additional threats to public safety, extraordinary public expense, cause fraud on or victimization of the public, or conflict with existing laws or ordinances.
4. A determination that the variance is the minimum necessary to afford relief, considering the flood hazard.
5. Submission to the applicant of written notice specifying the difference between the design flood elevation and the elevation to which the building is to be built, stating that the cost of flood insurance will be commensurate with the increased risk resulting from the reduced floor elevation, and stating that construction below the design flood elevation increases risks to life and property. Reserved.
104.11 Alternative materials, design and methods of construction and equipment. (No change)
(Mod CA4998 – R1 / AM)
Section 105 – Permits
Change Section 105.1 to read as follows:
105.1 Required. Any owner or authorized agent who intends to construct, enlarge, alter, repair, move, demolish, or change the occupancy of a building or structure, or to erect, install, enlarge, alter, repair, remove, convert or replace any impact resistant coverings, electrical, gas, mechanical or plumbing system, the installation of which is regulated by this code, or to cause any such work to be done, shall first make application to the building official and obtain the required permit.
(Mod CA5634 / AS)
Section 105 – Permits
Change Section 105.1.1 to read as follows:
105.1.1 Annual facility permit. In lieu of an individual permit for each alteration to an already approved existing electrical, gas, mechanical, or plumbing or interior nonstructural office system(s) installation, the building official is authorized to issue an annual permit upon application therefor to any person, firm or corporation regularly employing one or more qualified tradepersons in the building, structure or on the premises owned or operated by the applicant for the permit. for any occupancy to facilitate routine or emergency service, repair, refurbishing, minor renovations of service systems or manufacturing equipment installations/relocations. The building official shall be notified of major changes and shall retain the right to make inspections at the facility site as deemed necessary. An annual facility permit shall be assessed with an annual fee and shall be valid for one year from date of issuance. A separate permit shall be obtained for each facility and for each construction trade, as applicable. The permit application shall contain a general description of the parameters of work intended to be performed during the year.
Add Section 105.1.3 to read as follows:
105.1.3 Food permit. As per Section 500.12, Florida Statutes, a food permit from the Department of Agriculture and Consumer Services is required of any person who operates a food establishment or retail store.
Change Section 105.2 to read as follows:
105.2 Work exempt from permit. (No Change)
Building:
1. One-story detached accessory structures used as tool and storage sheds, playhouses and similar uses, provided the floor area is not greater than 120 square feet (11 m2).
2. Fences not over 7 feet (2134 mm) high.
3. Oil derricks.
4. Retaining walls that are not over 4 feet (1219 mm) in height measured from the bottom of the footing to the top of the wall, unless supporting a surcharge or impounding Class I, II or IIIA liquids.
5. Water tanks supported directly on grade if the capacity is not greater than 5,000 gallons (18 925 L) and the ratio of height to diameter or width is not greater than 2:1.
6. Sidewalks and driveways not more than 30 inches (762 mm) above adjacent grade, and not over any basement or story below and are not part of an accessible route.
7. Painting, papering, tiling, carpeting, cabinets, counter tops and similar finish work.
8. Temporary motion picture, television and theater stage sets and scenery.
9. Prefabricated swimming pools accessory to a Group R-3 occupancy that are less than 24 inches (610 mm) deep, are not greater than 5,000 gallons (18 925 L) and are installed entirely above ground.
10. Shade cloth structures constructed for nursery or agricultural purposes, not including service systems.
11. Swings and other playground equipment accessory to detached one- and two-family dwellings.
12. Window awnings in Group R-3 and U occupancies, supported by an exterior wall that do not project more than 54 inches (1372 mm) from the exterior wall and do not require additional support.
13. Nonfixed and movable fixtures, cases, racks, counters and partitions not over 5 feet 9 inches (1753 mm) in height.
Electrical:
Repairs and maintenance: Minor repair work, including the replacement of lamps or the connection of approved portable electrical equipment to approved permanently installed receptacles.
Radio and television transmitting stations: The provisions of this code shall not apply to electrical equipment used for radio and television transmissions, but do apply to equipment and wiring for a power supply and the installations of towers and antennas.
Temporary testing systems: A permit shall not be required for the installation of any temporary system required for the testing or servicing of electrical equipment or apparatus.
Gas: (No Change)
Mechanical:
1. – 7. (No Change)
8. The installation, replacement, removal or metering of any load management control device.
Plumbing: (No Change)
Change Section 105.2.2 to read as follows:
105.2.2 Repairs. Minor repairs. Ordinary minor repairs may be made with the approval of the building official without a permit, provided the repairs do Application or notice to the building official is not required for ordinary repairs to structures, replacement of lamps or the connection of approved portable electrical equipment to approved permanently installed receptacles. Such repairs shall not include the cutting away of any wall, partition or portion thereof, the removal or cutting of any structural beam or load-bearing support, or the removal or change of any required means of egress, or rearrangement of parts of a structure affecting the egress requirements; additionally, ordinary minor repairs shall not include addition to, alteration of, replacement or relocation of any standpipe, water supply, sewer, drainage, drain leader, gas, soil, waste, vent or similar piping, electric wiring systems or mechanical equipment or other work affecting public health or general safety, and such repairs shall not violate any of the provisions of the technical codes.
Change Section 105.3 to read as follows:
105.3 Application for permit. To obtain a permit, the applicant shall first file an application therefor in writing on a form furnished by the department of building safety building department for that purpose. Such application shall:
1. Identify and describe the work to be covered by the permit for which application is made.
2. Describe the land on which the proposed work is to be done by legal description, street address or similar description that will readily identify and definitely locate the proposed building or work.
3. Indicate the use and occupancy for which the proposed work is intended.
4. Be accompanied by construction documents and other information as required in Section 107.
5. State the valuation of the proposed work.
6. Be signed by the applicant, or the applicant’s authorized agent.
7. Give such other data and information as required by the building official.
Permit application forms shall be in the format prescribed by a local administrative board, if applicable, and must comply with the requirements of Section 713.135(5) and (6), Florida Statutes.
Each application shall be inscribed with the date of application, and the code in effect as of that date. For a building permit for which an application is submitted prior to the effective date of the Florida Building Code, the state minimum building code in effect in the permitting jurisdiction on the date of the application governs the permitted work for the life of the permit and any extension granted to the permit.
105.3.1 Action on application. The building official shall examine or cause to be examined applications for permits and amendments thereto within a reasonable time after filing. If the application or the construction documents do not conform to the requirements of pertinent laws, the building official shall reject such application in writing, stating the reasons therefor. If the building official is satisfied that the proposed work conforms to the requirements of this code and laws and ordinances applicable thereto, the building official shall issue a permit therefor as soon as practicable. When authorized through contractual agreement with a school board, in acting on applications for permits, the building official shall give first priority to any applications for the construction of, or addition or renovation to, any school or educational facility.
105.3.1.1 If a state university, Florida college or public school district elects to use a local government’s code enforcement offices, fees charged by counties and municipalities for enforcement of the Florida Building Code on buildings, structures, and facilities of state universities, state colleges, and public school districts shall not be more than the actual labor and administrative costs incurred for plans review and inspections to ensure compliance with the code.
105.3.1.2 No permit may be issued for any building construction, erection, alteration, modification, repair, or addition unless the applicant for such permit provides to the enforcing agency which issues the permit any of the following documents which apply to the construction for which the permit is to be issued and which shall be prepared by or under the direction of an engineer registered under Chapter 471, Florida Statutes:
1. Plumbing documents for any new building or addition which requires a plumbing system with more than 250 fixture units or which costs more than $125,000.
2. Fire sprinkler documents for any new building or addition which includes a fire sprinkler system which contains 50 or more sprinkler heads. Personnel as authorized by chapter 633 Florida Statutes, may design a fire sprinkler system of 49 or fewer heads and may design the alteration of an existing fire sprinkler system if the alteration consists of the relocation, addition or deletion of not more than 49 heads, notwithstanding the size of the existing fire sprinkler system.
3. Heating, ventilation, and air-conditioning documents for any new building or addition which requires more than a 15-ton-per-system capacity which is designed to accommodate 100 or more persons or for which the system costs more than $125,000. This paragraph does not include any document for the replacement or repair of an existing system in which the work does not require altering a structural part of the building or for work on a residential one, two, three or four-family structure.
An air-conditioning system may be designed by an installing air-conditioning contractor certified under Chapter 489, Florida Statutes, to serve any building or addition which is designed to accommodate fewer than 100 persons and requires an air-conditioning system with a value of $125,000 or less; and when a 15-ton-per system or less is designed for a singular space of a building and each 15-ton system or less has an independent duct system. Systems not complying with the above require design documents that are to be sealed by a professional engineer.
Example 1: When a space has two 10-ton systems with each having an independent duct system, the contractor may design these two systems since each unit (system) is less than 15 tons.
Example 2: Consider a small single-story office building which consists of six individual offices where each office has a single three-ton package air conditioning heat pump. The six heat pumps are connected to a single water cooling tower. The cost of the entire heating, ventilation and air-conditioning work is $47,000 and the office building accommodates fewer than 100 persons. Because the six mechanical units are connected to a common water tower this is considered to be an 18-ton system.
NOTE: It was further clarified by the Commission that the limiting criteria of 100 persons and $125,000 apply to the building occupancy load and the cost for the total air-conditioning system of the building.
4. Any specialized mechanical, electrical, or plumbing document for any new building or addition which includes a medical gas, oxygen, steam, vacuum, toxic air filtration, halon, or fire detection and alarm system which costs more than $5,000.
5. Electrical documents. See Florida Statutes 471.003(2)(h).
Documents requiring an engineer seal by this part shall not be valid unless a professional engineer who possesses a valid certificate of registration has signed, dated, and stamped such document as provided in Section 471.025, Florida Statutes.
6. All public swimming pools and public bathing places defined by and regulated under Chapter 514, Florida Statutes
105.3.3 An enforcing authority may not issue a building permit for any building construction, erection, alteration, modification, repair or addition unless the permit either includes on its face or there is attached to the permit the following statement: “NOTICE: In addition to the requirements of this permit, there may be additional restrictions applicable to this property that may be found in the public records of this county, and there may be additional permits required from other governmental entities such as water management districts, state agencies, or federal agencies.”
105.3.4 A building permit for a single-family residential dwelling must be issued within 30 working days of application therefor unless unusual circumstances require a longer time for processing the application or unless the permit application fails to satisfy the Florida Building Code or the enforcing agency’s laws or ordinances.
105.3.5 Identification of minimum premium policy. Except as otherwise provided in Chapter 440, Florida Statutes, Workers’ Compensation, every employer shall, as a condition to receiving a building permit, show proof that it has secured compensation for its employees as provided in Section 440.10 and 440.38, Florida Statutes.
105.3.6 Asbestos removal. Moving, removal or disposal of asbestos-containing materials on a residential building where the owner occupies the building, the building is not for sale or lease, and the work is performed according to the owner-builder limitations provided in this paragraph. To qualify for exemption under this paragraph, an owner must personally appear and sign the building permit application. The permitting agency shall provide the person with a disclosure statement in substantially the following form:
Disclosure Statement: State law requires asbestos abatement to be done by licensed contractors. You have applied for a permit under an exemption to that law. The exemption allows you, as the owner of your property, to act as your own asbestos abatement contractor even though you do not have a license. You must supervise the construction yourself. You may move, remove or dispose of asbestos-containing materials on a residential building where you occupy the building and the building is not for sale or lease, or the building is a farm outbuilding on your property. If you sell or lease such building within 1 year after the asbestos abatement is complete, the law will presume that you intended to sell or lease the property at the time the work was done, which is a violation of this exemption. You may not hire an unlicensed person as your contractor. Your work must be done according to all local, state and federal laws and regulations which apply to asbestos abatement projects. It is your responsibility to make sure that people employed by you have licenses required by state law and by county or municipal licensing ordinances.
105.3.7 Applicable Code for Manufactured Buildings. Manufacturers should be permitted to complete all buildings designed and approved prior to the effective date of a new code edition, provided a clear signed contract is in place. The contract shall provide specific data mirroring that required by an application for permit, specifically, without limitation, date of execution, building owner or dealer, and anticipated date of completion. However, the construction activity must commence within 6 months of the contract's execution. The contract is subject to verification by the Department of Business and Professional Regulation.
(Mod CA4999 - R1/ AM)
(Mod CA5753 / AS)
(Mod CA5250 / AS)
Section 105 – Permits
Change Section 105.5 to read as follows:
105.5 Expiration. Every permit issued shall become invalid unless the work on the site authorized by such permit is commenced within 180 days after its issuance, or if the work authorized on the site by such permit is suspended or abandoned for a period of 180 days after the time the work is commenced. The building official is authorized to grant, in writing, one or more extensions of time, for periods not more than 180 days each. The extension shall be requested in writing and justifiable cause demonstrated. Reserved.
(Mod CA5002-R1 / AM)
Section 105 – Permits
Change Section 105.6 to read as follows:
105.6 Suspension or revocation. Denial or revocation. The building official is authorized to suspend or revoke a permit issued under the provisions of this code wherever the permit is issued in error or on the basis of incorrect, inaccurate or incomplete information, or in violation of any ordinance or regulation or any of the provisions of this code. Whenever a permit required under this section is denied or revoked because the plan, or the construction, erection, alteration, modification, repair, or demolition of a building, is found by the local enforcing agency to be not in compliance with the Florida Building Code, the local enforcing agency shall identify the specific plan or project features that do not comply with the applicable codes, identify the specific code chapters and sections upon which the finding is based, and provide this information to the permit applicant. If the local building code administrator or inspector finds that the plans are not in compliance with the Florida Building Code, the local building code administrator or inspector shall identify the specific plan features that do not comply with the applicable codes, identify the specific code chapters and sections upon which the finding is based, and provide this information to the local enforcing agency. The local enforcing agency shall provide this information to the permit applicant.
(Mod CA5006 / AS)
Section 105 – Permits
Add Section 105.8 to read as follows:
105.8 Notice of commencement. As per Section 713.135, Florida Statutes, when any person applies for a building permit, the authority issuing such permit shall print on the face of each permit card in no less than 14-point, capitalized, boldfaced type: “WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT.”
(Mod CA5021-R1 / AM)
Section 105 – Permits
Add Section 105.9 to read as follows:
105.9 Asbestos. The enforcing agency shall require each building permit for the demolition or renovation of an existing structure to contain an asbestos notification statement which indicates the owner’s or operator’s responsibility to comply with the provisions of Section 469.003, Florida Statutes, and to notify the Department of Environmental Protection of his or her intentions to remove asbestos, when applicable, in accordance with state and federal law.
(Mod CA5022-R1 / AM)
Section 105 – Permits
Add Section 105.10 to read as follows:
105.10 Certificate of protective treatment for prevention of termites. A weather-resistant job-site posting board shall be provided to receive duplicate treatment certificates as each required protective treatment is completed, providing a copy for the person the permit is issued to and another copy for the building permit files. The treatment certificate shall provide the product used, identity of the applicator, time and date of the treatment, site location, area treated, chemical used, percent concentration and number of gallons used, to establish a verifiable record of protective treatment. If the soil chemical barrier method for termite prevention is used, final exterior treatment shall be completed prior to final building approval.
(Mod CA5078-R1 / AM)
Section 105 – Permits
Add Section 105.11 to read as follows:
105.11 Notice of termite protection. A permanent sign which identifies the termite treatment provider and need for reinspection and treatment contract renewal shall be provided. The sign shall be posted near the water heater or electric panel.
(Mod CA5079-R1 / AM)
Section 105 – Permits
Add Section 105.12 to read as follows:
105.12 Work starting before permit issuance. Upon approval of the building official, the scope of work delineated in the building permit application and plan may be started prior to the final approval and issuance of the permit, provided any work completed is entirely at risk of the permit applicant and the work does not proceed past the first required inspection.
(Mod CA 5080 / AS)
Section 105 – Permits
Add Section 105.13 to read as follows:
105.13 Phased permit approval. After submittal of the appropriate construction documents, the building official is authorized to issue a permit for the construction of foundations or any other part of a building or structure before the construction documents for the whole building or structure have been submitted. The holder of such permit for the foundation or other parts of a building or structure shall proceed at the holder’s own risk with the building operation and without assurance that a permit for the entire structure will be granted. Corrections may be required to meet the requirements of the technical codes.
(Mod CA5081 / AS)
Section 105 – Permits
Add Section 105.14 to read as follows:
105.14 Permit issued on basis of an affidavit. Whenever a permit is issued in reliance upon an affidavit or whenever the work to be covered by a permit involves installation under conditions which, in the opinion of the building official, are hazardous or complex, the building official shall require that the architect or engineer who signed the affidavit or prepared the drawings or computations shall supervise such work. In addition, they shall be responsible for conformity to the permit, provide copies of inspection reports as inspections are performed, and upon completion make and file with the building official written affidavit that the work has been done in conformity to the reviewed plans and with the structural provisions of the technical codes. In the event such architect or engineer is not available, the owner shall employ in his stead a competent person or agency whose qualifications are reviewed by the building official. The building official shall ensure that any person conducting plans review is qualified as a plans examiner under Part XII of Chapter 468, Florida Statutes, and that any person conducting inspections is qualified as a building inspector under Part III of Chapter 468, Florida Statutes.
Exception: Permit issued on basis of an affidavit shall not extend to the flood load and flood resistance requirements of the Florida Building Code.
(Mod CA5082-R1 / AM)
Section 105 – Permits
Add Section 105.15 to read as follows:
105.15 Opening protection. When any activity requiring a building permit that is applied for on or after July 1, 2008, and for which the estimated cost is $50,000 or more for a site built single-family detached residential structure that is located in the wind borne debris region as defined in this Code and that has an insured value of $750,000 or more, or, if the site built single-family detached residential structure is uninsured or for which documentation of insured value is not presented, has a just valuation for the structure for purposes of ad valorem taxation of $750,000 or more; opening protections as required within this Code or Florida Building Code, Residential for new construction shall be provided.
Exception: Single family residential structures permitted subject to the Florida Building Code are not required to comply with this section.
(Mod CA5083 / AS)
Section 107 – Submittal Documents
Change Section 107.3 to read as follows:
107.3 Examination of documents. The building official shall examine or cause to be examined the accompanying submittal documents and shall ascertain by such examinations whether the construction indicated and described is in accordance with the requirements of this code and other pertinent laws or ordinances.
Exceptions:
1. Building plans approved pursuant to Section 553.77(5), Florida Statutes, and state-approved manufactured buildings are exempt from local codes enforcing agency plan reviews except for provisions of the code relating to erection, assembly or construction at the site. Erection, assembly and construction at the site are subject to local permitting and inspections. Photocopies of plans approved according to FAC 9B-1.009, F.A.C., shall be sufficient for local permit application documents of record for the modular building portion of the permitted project.
2. Industrial construction on sites where design, construction and fire safety are supervised by appropriate design and inspection professionals and which contain adequate in-house fire departments and rescue squads is exempt, subject to local government option, from review of plans and inspections, providing owners certify that applicable codes and standards have been met and supply appropriate approved drawings to local building and fire-safety inspectors.
(Mod CA 5085/ AS)
Section 107 – Submittal Documents
Add Section 107.3.4.3 to read as follows:
107.3.4.2 Certifications by contractors authorized under the provisions of Section 489.115(4)(b), Florida Statutes, shall be considered equivalent to sealed plans and specifications by a person licensed under Chapter 471, Florida Statutes, or Chapter 481 Florida Statutes, by local enforcement agencies for plans review for permitting purposes relating to compliance with the wind-resistance provisions of the code or alternate methodologies approved by the Florida Building Commission for one- and two-family dwellings. Local enforcement agencies may rely upon such certification by contractors that the plans and specifications submitted conform to the requirements of the code for wind resistance. Upon good cause shown, local government code enforcement agencies may accept or reject plans sealed by persons licensed under Chapters 471, 481 or 489, Florida Statutes.
(Mod CA 5086 / AS)
Section 107 – Submittal Documents
Add Section 107.3.5 to read as follows:
107.3.5 Minimum plan review criteria for buildings. The examination of the documents by the building official shall include the following minimum criteria and documents: a floor plan; site plan; foundation plan; floor/roof framing plan or truss layout; all fenestration penetrations; flashing; and rough opening dimensions; and all exterior elevations:
Commercial Buildings:
Building
1. Site requirements:
Parking
Fire access
Vehicle loading
Driving/turning radius
Fire hydrant/water supply/post indicator valve (PIV)
Set back/separation (assumed property lines)
Location of specific tanks, water lines and sewer lines
Flood hazard areas, flood zones, and design flood elevations
2. Occupancy group and special occupancy requirements shall be determined.
3. Minimum type of construction shall be determined (see Table 503).
4. Fire-resistant construction requirements shall include the following components:
Fire-resistant separations
Fire-resistant protection for type of construction
Protection of openings and penetrations of rated walls
Fire blocking and draftstopping and calculated fire resistance
5. Fire suppression systems shall include:
Early warning smoke evacuation systems Schematic fire sprinklers
Standpipes
Preengineered systems
Riser diagram
Same as above.
6. Life safety systems shall be determined and shall include the following requirements:
Occupant load and egress capacities
Early warning
Smoke control
Stair pressurization
Systems schematic
7. Occupancy load/egress requirements shall include:
Occupancy load
Gross
Net
Means of egress
Exit access
Exit
Exit discharge
Stairs construction/geometry and protection
Doors
Emergency lighting and exit signs
Specific occupancy requirements
Construction requirements
Horizontal exits/exit passageways
8. Structural requirements shall include:
Soil conditions/analysis
Termite protection
Design loads
Wind requirements
Building envelope
Impact resistant coverings or systems
Structural calculations (if required)
Foundation
Flood requirements in accordance with Section 1612, including lowest floor elevations, enclosures, flood damage-resistant materials
Wall systems
Floor systems
Roof systems
Threshold inspection plan
Stair systems
9. Materials shall be reviewed and shall at a minimum include the following:
Wood
Steel
Aluminum
Concrete
Plastic
Glass
Masonry
Gypsum board and plaster
Insulating (mechanical)
Roofing
Insulation
10. Accessibility requirements shall include the following:
Site requirements
Accessible route
Vertical accessibility
Toilet and bathing facilities
Drinking fountains
Equipment
Special occupancy requirements
Fair housing requirements
11. Interior requirements shall include the following:
Interior finishes (flame spread/smoke development)
Light and ventilation
Sanitation
12. Special systems:
Elevators
Escalators
Lifts
13. Swimming pools:
Barrier requirements
Spas
Wading pools
Electrical
1. Electrical:
Wiring
Services
Feeders and branch circuits
Overcurrent protection
Grounding
Wiring methods and materials
GFCIs
2. Equipment
3. Special occupancies
4. Emergency systems
5. Communication systems
6. Low voltage
7. Load calculations
8. Design flood elevation
Plumbing
1. Minimum plumbing facilities
2. Fixture requirements
3. Water supply piping
4. Sanitary drainage
5. Water heaters
6. Vents
7. Roof drainage
8. Back flow prevention
9. Irrigation
10. Location of water supply line
11. Grease traps
12. Environmental requirements
13. Plumbing riser
14. Design flood elevation
Mechanical
1. Energy calculations
2. Exhaust systems:
Clothes dryer exhaust
Kitchen equipment exhaust
Specialty exhaust systems
3. Equipment
4. Equipment location
5. Make-up air
6. Roof-mounted equipment
7. Duct systems
8. Ventilation
9. Combustion air
10. Chimneys, fireplaces and vents
11. Appliances
12. Boilers
13. Refrigeration
14. Bathroom ventilation
15. Laboratory
16. Design flood elevation
Gas
1. Gas piping
2. Venting
3. Combustion air
4. Chimneys and vents
5. Appliances
6. Type of gas
7. Fireplaces
8. LP tank location
9. Riser diagram/shutoffs
10. Design flood elevation
Demolition
1. Asbestos removal
Residential (one- and two-family)
1. Site requirements
Set back/separation (assumed property lines)
Location of septic tanks
2. Fire-resistant construction (if required)
3. Fire
4. Smoke detector locations
5. Egress
Egress window size and location stairs construction requirements
6. Structural requirements shall include:
Wall section from foundation through roof, including assembly and materials connector tables wind requirements structural calculations (if required)
Flood hazard areas, flood zones, design flood elevations, lowest floor elevations, enclosures, equipment, and flood damage-resistant materials
7. Accessibility requirements: show/identify accessible bath
8. impact resistant coverings or systems
Exemptions.
Plans examination by the building official shall not be required for the following work:
1. Replacing existing equipment such as mechanical units, water heaters, etc.
2. Reroofs
3. Minor electrical, plumbing and mechanical repairs
4. Annual maintenance permits
5. Prototype plans
Except for local site adaptions, siding, foundations and/or modifications.
Except for structures that require waiver.
6. Manufactured buildings plan except for foundations and modifications of buildings on site.
(Mod SP 5254 / AS)
(Mod CA 5087 / AS)
(Mod CA 5766 / AS)
Section 107 – Submittal Documents
Add Section 107.6. to read as follows:
107.6 Affidavits. The building official may accept a sworn affidavit from a registered architect or engineer stating that the plans submitted conform to the technical codes. For buildings and structures, the affidavit shall state that the plans conform to the laws as to egress, type of construction and general arrangement and, if accompanied by drawings, show the structural design and that the plans and design conform to the requirements of the technical codes as to strength, stresses, strains, loads and stability. The building official may without any examination or inspection accept such affidavit, provided the architect or engineer who made such affidavit agrees to submit to the building official copies of inspection reports as inspections are performed and upon completion of the structure, electrical, gas, mechanical or plumbing systems a certification that the structure, electrical, gas, mechanical or plumbing system has been erected in accordance with the requirements of the technical codes. Where the building official relies upon such affidavit, the architect or engineer shall assume full responsibility for compliance with all provisions of the technical codes and other pertinent laws or ordinances. The building official shall ensure that any person conducting plans review is qualified as a plans examiner under Part XII of Chapter 468, Florida Statutes, and that any person conducting inspections is qualified as a building inspector under Part XII of Chapter 468, Florida Statutes.
(Mod CA 5088 / AS)
Section 107 – Submittal Documents
Add Section 107.6.1 to read as follows:
107.6.1 Building permits issued on the basis of an affidavit. Pursuant to the requirements of federal regulation for participation in the National Flood Insurance Program (44 C.F.R. Parts 59 and 60), the authority granted to the Building Official to issue permits, to rely on inspections, and to accept plans and construction documents on the basis of affidavits and plans submitted pursuant to 105.14 and Section 107.6, shall not extend to the flood load and flood resistance construction requirements of the Florida Building Code.
(Mod SP 5255 / AS)
Section 109 – Fees
Change Section 109.5 to read as follows:
109.5 Related fees. The payment of the fee for the construction, alteration, removal or demolition for work done in connection to or concurrently with the work authorized by a building permit shall not relieve the applicant or holder of the permit from the payment of other fees that are prescribed by law. Reserved.
(Mod CA5091-R1 / AM)
Section 109 – Fees
Change Section 109.6 to read as follows:
109.6 Refunds. The building official is authorized to establish a refund policy. Reserved.
(Mod CA5092-R1 / AM)
Section 110 – Inspections
Change Section 110.3.5 to read as follows:
110.3 Required inspections. The building official, upon notification, shall make the inspections set forth in Sections 110.3.1 through 110.3.10. The building official upon notification from the permit holder or his or her agent shall make the following inspections, and shall either release that portion of the construction or shall notify the permit holder or his or her agent of any violations which must be corrected in order to comply with the technical codes. The building official shall determine the timing and sequencing of when inspections occur and what elements are inspected at each inspection.
Building
1. Foundation inspection. To be made after trenches are excavated and forms erected and shall at a minimum include the following building components:
·Stem-wall
·Monolithic slab-on-grade
·Piling/pile caps
·Footers/grade beams
1.1. In flood hazard areas, upon placement of the lowest floor, including basement, and prior to further vertical construction, the elevation certification shall be submitted to the authority having jurisdiction.
2. Framing inspection. To be made after the roof, all framing, fireblocking and bracing is in place, all concealing wiring, all pipes, chimneys, ducts and vents are complete and shall at a minimum include the following building components:
·Window/door framing
·Vertical cells/columns
·Lintel/tie beams
·Framing/trusses/bracing/connectors
·Draft stopping/fire blocking
·Curtain wall framing
·Energy insulation
·Accessibility.
·Verify rough opening dimensions are within tolerances.
3. Sheathing inspection. To be made either as part of a dry-in inspection or done separately at the request of the contractor after all roof and wall sheathing and fasteners are complete and shall at a minimum include the following building components:
·Roof sheathing
·Wall sheathing
·Sheathing fasteners
·Roof/wall dry-in.
4. Roofing inspection. Shall at a minimum include the following building components:
·Dry-in
·Insulation
·Roof coverings
·Flashing
5. Final inspection. To be made after the building is completed and ready for occupancy.
5.1. In flood hazard areas, as part of the final inspection, a final certification of the lowest floor elevation shall be submitted to the authority having jurisdiction.
6. Swimming pool inspection. First inspection to be made after excavation and installation of reinforcing steel, bonding and main drain and prior to placing of concrete.
Final inspection to be made when the swimming pool is complete and all required enclosure requirements are in place.
In order to pass final inspection and receive a certificate of completion, a residential swimming pool must meet the requirements relating to pool safety features as described in Section 424.2.17.
7. Demolition inspections. First inspection to be made after all utility connections have been disconnected and secured in such manner that no unsafe or unsanitary conditions shall exist during or after demolition operations.
Final inspection to be made after all demolition work is completed.
8. Manufactured building inspections. The building department shall inspect construction of foundations; connecting buildings to foundations; installation of parts identified on plans as site installed items, joining the modules, including utility crossovers; utility connections from the building to utility lines on site; and any other work done on site which requires compliance with the Florida Building Code. Additional inspections may be required for public educational facilities (see Section 423.27.20).
9. Where impact resistant coverings or impact resistant systems are installed , the building official shall schedule adequate inspections of impact resistant coverings or impact resistant systems to determine the following:
The system indicated on the plans was installed.
The system is installed in accordance with the manufacturer’s installation instructions and the product approval.
Electrical
1. Underground inspection. To be made after trenches or ditches are excavated, conduit or cable installed, and before any backfill is put in place.
2. Rough-in inspection. To be made after the roof, framing, fireblocking and bracing is in place and prior to the installation of wall or ceiling membranes.
3. Final inspection. To be made after the building is complete, all required electrical fixtures are in place and properly connected or protected, and the structure is ready for occupancy.
Plumbing
1. Underground inspection. To be made after trenches or ditches are excavated, piping installed, and before any backfill is put in place.
2. Rough-in inspection. To be made after the roof, framing, fireblocking and bracing is in place and all soil, waste and vent piping is complete, and prior to this installation of wall or ceiling membranes.
3. Final inspection. To be made after the building is complete, all plumbing fixtures are in place and properly connected, and the structure is ready for occupancy.
Note: See Section P312 of the Florida Building Code, Plumbing for required tests.
Mechanical
1. Underground inspection. To be made after trenches or ditches are excavated, underground duct and fuel piping installed, and before any backfill is put in place.
2. Rough-in inspection. To be made after the roof, framing, fire blocking and bracing are in place and all ducting, and other concealed components are complete, and prior to the installation of wall or ceiling membranes.
3. Final inspection. To be made after the building is complete, the mechanical system is in place and properly connected, and the structure is ready for occupancy.
Gas
1. Rough piping inspection. To be made after all new piping authorized by the permit has been installed, and before any such piping has been covered or concealed or any fixtures or gas appliances have been connected.
2. Final piping inspection. To be made after all piping authorized by the permit has been installed and after all portions which are to be concealed by plastering or otherwise have been so concealed, and before any fixtures or gas appliances have been connected. This inspection shall include a pressure test.
3. Final inspection. To be made on all new gas work authorized by the permit and such portions of existing systems as may be affected by new work or any changes, to ensure compliance with all the requirements of this code and to assure that the installation and construction of the gas system is in accordance with reviewed plans.
(Mod CA 5252 / AS)
(Mod SP 5254/ AS)
Section 110 – Inspections
Add Section 110.3.11 to read as follows:
| |
|110.3.11 Termites. Building components and building surroundings required to be protected from termite damage in |
|accordance with Section 1503.7, Section 2304.13 or Section 2304.11.6, specifically required to be inspected for |
|termites in accordance with Section 2114, or required to have chemical soil treatment in accordance with Section 1816 |
|shall not be covered or concealed until the release from the building official has been received. |
| (Mod CA5093-R1 / AM) |
Section 110 – Inspections
Add Section 110.3.12 to read as follows:
110.3.12 Impact resistant coverings or systems. Where impact resistant coverings or systems are installed to meet requirements of this code, the building official shall schedule adequate inspections of impact resistant coverings or systems to determine the following:
1. The system indicated on the plans was installed.
2. The system is installed in accordance with the manufacturer’s installation instructions and the product approval.
(Mod CA 5637 / AS)
Section 110 – Inspections
Change Section 110.4 to read as follows:
110.4 Inspection agencies. The building official is authorized to accept reports of approved inspection agencies, provided such agencies satisfy the requirements as to qualifications and reliability. Reserved.
(Mod CA5096-R1 / AM)
Section 110 – Inspections
Add Sections 110.7 – 110.8 to read as follows:
110.7 Shoring. For threshold buildings, shoring and associated formwork or falsework shall be designed and inspected by a Florida licensed professional engineer, employed by the permit holder or subcontractor, prior to any required mandatory inspections by the threshold building inspector.
110.8 Threshold building.
110.8.1 The enforcing agency shall require a special inspector to perform structural inspections on a threshold building pursuant to a structural inspection plan prepared by the engineer or architect of record. The structural inspection plan must be submitted to the enforcing agency prior to the issuance of a building permit for the construction of a threshold building. The purpose of the structural inspection plans is to provide specific inspection procedures and schedules so that the building can be adequately inspected for compliance with the permitted documents. The special inspector may not serve as a surrogate in carrying out the responsibilities of the building official, the architect, or the engineer of record. The contractor's contractual or statutory obligations are not relieved by any action of the special inspector.
110.8.2 The special inspector shall determine that a professional engineer who specializes in shoring design has inspected the shoring and reshoring for conformance with the shoring and reshoring plans submitted to the enforcing agency. A fee simple title owner of a building, which does not meet the minimum size, height, occupancy, occupancy classification, or number-of-stories criteria which would result in classification as a threshold building under s. 553.71(7), may designate such building as a threshold building, subject to more than the minimum number of inspections required by the Florida Building Code.
110.8.3 The fee owner of a threshold building shall select and pay all costs of employing a special inspector, but the special inspector shall be responsible to the enforcement agency. The inspector shall be a person certified, licensed or registered under Chapter 471, Florida Statutes, as an engineer or under Chapter 481, Florida Statutes, as an architect.
110.8.4 Each enforcement agency shall require that, on every threshold building:
110.8.4.1 The special inspector, upon completion of the building and prior to the issuance of a certificate of occupancy, file a signed and sealed statement with the enforcement agency in substantially the following form: “To the best of my knowledge and belief, the above described construction of all structural load-bearing components complies with the permitted documents, and the shoring and reshoring conforms to the shoring and reshoring plans submitted to the enforcement agency.”
110.8.4.2 Any proposal to install an alternate structural product or system to which building codes apply be submitted to the enforcement agency for review for compliance with the codes and made part of the enforcement agency’s recorded set of permit documents.
110.8.4.3 All shoring and reshoring procedures, plans and details be submitted to the enforcement agency for recordkeeping. Each shoring and reshoring installation shall be supervised, inspected and certified to be in compliance with the shoring documents by the contractor.
110.8.4.4 All plans for the building which are required to be signed and sealed by the architect or engineer of record contain a statement that, to the best of the architect’s or engineer’s knowledge, the plans and specifications comply with the applicable minimum building codes and the applicable fire-safety standards as determined by the local authority in accordance with this section and Chapter 633, Florida Statutes.
110.8.5 No enforcing agency may issue a building permit for construction of any threshold building except to a licensed general contractor, as defined in Section 489.105(3)(a), Florida Statutes, or to a licensed building contractor, as defined in Section 489.105(3)(b), Florida Statutes, within the scope of her or his license. The named contractor to whom the building permit is issued shall have the responsibility for supervision, direction, management and control of the construction activities on the project for which the building permit was issued.
110.8.6 The building department may allow a special inspector to conduct the minimum structural inspection of threshold buildings required by this code, Section 553.73, Florida Statutes, without duplicative inspection by the building department. The building official is responsible for ensuring that any person conducting inspections is qualified as a building inspector under Part XII of Chapter 468, Florida Statutes, or certified as a special inspector under Chapter 471 or 481, Florida Statutes. Inspections of threshold buildings required by Section 553.79(5), Florida Statutes, are in addition to the minimum inspections required by this code.
(Mod CA5093-R1 / AM)
Section 111 – Certificate of Occupancy
Change Section 111.2 to read as follows:
111.2 Certificate issued. After the building official inspects the building or structure and finds no violations of the provisions of this code or other laws that are enforced by the department of building safety, the building official shall issue a certificate of occupancy that contains the following:
1. The building permit number.
2. The address of the structure.
3. The name and address of the owner.
4. A description of that portion of the structure for which the certificate is issued.
5. A statement that the described portion of the structure has been inspected for compliance with the requirements of this code for the occupancy and division of occupancy and the use for which the proposed occupancy is classified.
6. For buildings and structures in flood hazard areas, a statement that documentation of the as-built lowest floor elevation has been provided and is retained in the records of the authority having jurisdiction department of building safety.
6. 7. The name of the building official.
7. 8. The edition of the code under which the permit was issued.
8. 9. The use and occupancy, in accordance with the provisions of Chapter 3.
9. 10. The type of construction as defined in Chapter 6.
10 11. The design occupant load.
11. 12. If an automatic sprinkler system is provided, whether the sprinkler system is required.
12. 13. Any special stipulations and conditions of the building permit.
(Mod SP5254 / AS)
Section 111 – Certificate of Occupancy
Add Section 111.5 to read as follows:
111.5 Certificate of Completion. A Certificate of Completion is proof that a structure or system is complete and for certain types of permits is released for use and may be connected to a utility system. This certificate does not grant authority to occupy a building, such as shell building, prior to the issuance of a Certificate of Occupancy.
(Mod CA5097-R1 / AM)
Section 113 – Board of Appeals
Change Section 113 to read as follows:
SECTION 113
BOARD OF APPEALS
RESERVED
113.1 General. In order to hear and decide appeals of orders, decisions or determinations made by the building official relative to the application and interpretation of this code, there shall be and is hereby created a board of appeals. The board of appeals shall be appointed by the applicable governing authority and shall hold office at its pleasure. The board shall adopt rules of procedure for conducting its business.
113.2 Limitations on authority. An application for appeal shall be based on a claim that the true intent of this code or the rules legally adopted thereunder have been incorrectly interpreted, the provisions of this code do not fully apply or an equally good or better form of construction is proposed. The board shall have no authority to waive requirements of this code.
113.3 Qualifications. The board of appeals shall consist of members who are qualified by experience and training to pass on matters pertaining to building construction and are not employees of the jurisdiction.
(Mod CA5100-R1 / AM)
Section 114 – Violations
Change Section 114 to read as follows:
SECTION 114
VIOLATIONS
RESERVED
114.1 Unlawful acts. It shall be unlawful for any person, firm or corporation to erect, construct, alter, extend, repair, move, remove, demolish or occupy any building, structure or equipment regulated by this code, or cause same to be done, in conflict with or in violation of any of the provisions of this code.
114.2 Notice of violation. The building official is authorized to serve a notice of violation or order on the person responsible for the erection, construction, alteration, extension, repair, moving, removal, demolition or occupancy of a building or structure in violation of the provisions of this code, or in violation of a permit or certificate issued under the provisions of this code. Such order shall direct the discontinuance of the illegal action or condition and the abatement of the violation.
114.3 Prosecution of violation. If the notice of violation is not complied with promptly, the building official is authorized to request the legal counsel of the jurisdiction to institute the appropriate proceeding at law or in equity to restrain, correct or abate such violation, or to require the removal or termination of the unlawful occupancy of the building or structure in violation of the provisions of this code or of the order or direction made pursuant thereto.
114.4 Violation penalties. Any person who violates a provision of this code or fails to comply with any of the requirements thereof or who erects, constructs, alters or repairs a building or structure in violation of the approved construction documents or directive of the building official, or of a permit or certificate issued under the provisions of this code, shall be subject to penalties as prescribed by law.
(Mod CA5101-R1 / AM)
Section 116 – Unsafe Structures and Equipment
Change Section 116 to read as follows:
SECTION 116
UNSAFE STRUCTURES AND EQUIPMENT
RESERVED
116.1 Conditions. Structures or existing equipment that are or hereafter become unsafe, insanitary or deficient because of inadequate means of egress facilities, inadequate light and ventilation, or which constitute a fire hazard, or are otherwise dangerous to human life or the public welfare, or that involve illegal or improper occupancy or inadequate maintenance, shall be deemed an unsafe condition. Unsafe structures shall be taken down and removed or made safe, as the building official deems necessary and as provided for in this section. A vacant structure that is not secured against entry shall be deemed unsafe.
116.2 Record. The building official shall cause a report to be filed on an unsafe condition. The report shall state the occupancy of the structure and the nature of the unsafe condition.
116.3 Notice. If an unsafe condition is found, the building official shall serve on the owner, agent or person in control of the structure, a written notice that describes the condition deemed unsafe and specifies the required repairs or improvements to be made to abate the unsafe condition, or that requires the unsafe structure to be demolished within a stipulated time. Such notice shall require the person thus notified to declare immediately to the building official acceptance or rejection of the terms of the order.
116.4 Method of service. Such notice shall be deemed properly served if a copy thereof is (a) delivered to the owner personally; (b) sent by certified or registered mail addressed to the owner at the last known address with the return receipt requested; or (c) delivered in any other manner as prescribed by local law. If the certified or registered letter is returned showing that the letter was not delivered, a copy thereof shall be posted in a conspicuous place in or about the structure affected by such notice. Service of such notice in the foregoing manner upon the owner’s agent or upon the person responsible for the structure shall constitute service of notice upon the owner.
116.5 Restoration. The structure or equipment determined to be unsafe by the building official is permitted to be restored to a safe condition. To the extent that repairs, alterations or additions are made or a change of occupancy occurs during the restoration of the structure, such repairs, alterations, additions or change of occupancy shall comply with the requirements of Section 105.2.2 and Chapter 34.
(Mod CA5103-R1 / AM)
Section 117 – Variances in Flood Hazard Areas
Add Section 117 to read as follows:
SECTION 117
VARIANCES IN FLOOD HAZARD AREAS
117.1 Flood hazard areas. Pursuant to section 553.73(5), F.S., the variance procedures adopted in the local floodplain management ordinance shall apply to requests submitted to the Building Official for variances to the provisions of Section 1612.4 of the Florida Building Code, Building or, as applicable, the provisions of R322 of the Florida Building Code, Residential. This section shall not apply to Section 3109 of the Florida Building Code, Building.
(Mod SP 5255 / AS)
Chapter 2 – Definitions
Section 202 – Definitions
Change Section 202 to read as follows:
ACCESSIBLE. A site, building, facility or portion thereof that complies with Chapter 11. See the Florida Building Code, Accessibility. (Mod A5104 / AM)
ACCESSIBLE ROUTE. A continuous, unobstructed path that complies with Chapter 11. See the Florida Building Code, Accessibility. (Mod A5104 / AM)
ACCESSIBLE UNIT. A dwelling unit or sleeping unit that complies with this code and the provisions for Accessible units in ICC A117.1. See the Florida Building Code, Accessibility. (Mod A5104 / AM)
ADDITION. An extension or increase in floor area, number of stories or height of a building or structure. (Mod F5191 / AS)
AGRICULTURAL, BUILDING. A structure designed and constructed to house farm implements, hay, grain, poultry, livestock or other horticultural products. This structure shall not be a place of human habitation or a place of employment where agricultural products are processed, treated or packaged, nor shall it be a place used by the public. Reserved (Mod CA5188 / AM)
APPLICABLE GOVERNING BODY. A city, county, state, state agency or other political government subdivision or entity authorized to administer and enforce the provisions of this code, as adopted or amended. Also applies to administrative authority. (Mod CA5188 / AM)
ARCHITECT. A Florida-registered architect. (Mod CA5188 / AM)
AWNING. An architectural projection that provides weather protection, identity or decoration and is partially or wholly supported by the building to which it is attached. An awning is comprised of a lightweight frame structure over which a covering is attached. An awning may be rigid fixed or moveable, cantilevered, or otherwise entirely supported from a building.
(Mod S5936 – R1 / AM)
BURIAL CHAMBER MAUSOLEUM. A family mausoleum consisting of 6 or fewer casket placement crypts plus a chamber to be used for loading of caskets from the interior of the mausoleum which is not below the level of the ground and which is substantially exposed above ground. (Florida Specific Amendment)
CARBON DIOXIDE EXTINGUISHING SYSTEMS. A system supplying carbon dioxide (CO2) from a pressurized vessel through fixed pipes and nozzles. The system includes a manual- or automatic-actuating mechanism. See Section 902.1. (Mod F5191 / AS)
CARBON MONOXIDE ALARM. A device for the purpose of detecting carbon monoxide, that produces a distinct audible alarm, and is listed or labeled with the appropriate standard, either ANSI/UL 2034 - 96, Standard for Single and Multiple Station CO Alarms, or UL 2075 - 04, Gas and Vapor Detector Sensor, in accordance with its application. (Mod F5191 / AS)
CHAPEL MAUSOLEUM. A mausoleum for the public that has heat or air conditioning, with or without a committal area or office. (Florida Specific Amendment)
CIRCULATION PATH. An exterior or interior way of passage from one place to another for pedestrians. See the Florida Building Code, Accessibility. (Mod A5104 / AM)
COASTAL HIGH HAZARD AREA FLOOD HAZARD AREA SUBJECT TO HIGH-VELOCITY WAVE ACTION. Area within the special flood hazard area extending from offshore to the inland limit of a primary frontal dune along an open coast and any other area that is subject to high-velocity wave action from storms or seismic sources, and shown on a Flood Insurance Rate Map (FIRM) or other flood hazard map as velocity zones Zone V, VO, VE or V1-30. (Mod SP 5274 / AS)
COLUMBARIUM. A permanent structure consisting of niches. (Florida Specific Amendment)
COMMISSION. The Florida Building Commission. (Florida Specific Amendment)
COMPANION CRYPT. A permanent chamber in a mausoleum for the containment of human remains of more than one individual. (Florida Specific Amendment)
CRYPT. A permanent chamber in a mausoleum for the containment of human remains. (Florida Specific Amendment)
DETECTABLE WARNING. See the Florida Building Code, Accessibility. (Mod A5104 / AM)
DRY FLOODPROOFING. A combination of design modifications that results in a building or structure, including the attendant utility utilities and equipment and sanitary facilities, being water tight with walls substantially impermeable to the passage of water and with structural components having the capacity to resist loads as identified in ASCE 7. (Mod SP5259 / AS)
DWELLING UNIT OR SLEEPING UNIT, TYPE A. Reserved. (Mod A5104 / AM)
DWELLING UNIT OR SLEEPING UNIT, TYPE B. Reserved. (Mod A5104 / AM)
EMPLOYEE WORK AREA. All or any portion of a space used only by employees and only for work. Corridors, toilet rooms, kitchenettes and break rooms are not employee work areas. See the Florida Building Code, Accessibility. (Mod A5104 / AM)
ENFORCEMENT AGENCY.
Local enforcement agency. Means an agency of local government with authority to make inspections of buildings and to enforce the codes which establish standards for design, construction, erection, alteration, repair, modification or demolition of public or private buildings, structures or facilities.
State enforcement agency. Means the agency of state government with authority to make inspections of buildings and to enforce the codes, as required by this part, which establish standards for design, construction, erection, alteration, repair, modification or demolition of public or private buildings, structures or facilities. (Mod CA5188 / AM)
ENGINEER. A Florida-registered engineer. (Mod CA5188 / AM)
FAMILY MAUSOLEUM. A mausoleum for the private use of a family or group of family members. (Florida Specific Amendment)
FLOATING RESIDENTIAL UNIT. Means a structure primarily designed or constructed as a living unit, built on a floating base, which is not designed primarily as a vessel, is not self-propelled although it may be towed about from place to place, and is primarily intended to be anchored or otherwise moored in a fixed location. (Mod CA5188 / AM)
GARAGE DOOR MANUFACTURER: The party responsible for the completed assembly of the garage door components. (Mod S5324 / AS)
GARDEN MAUSOLEUM. A mausoleum for the public built without heat or air conditioning but may contain an open-air committal area. (Florida Specific Amendment)
HABITABLE SPACE. A space in a building structure for living, sleeping, eating or cooking. Bathrooms, toilet rooms, closets, halls, screen enclosures, sunroom Categories I, II and III as defined in the AAMA/NPEA/NSA 2100, storage or utility spaces and similar areas are not considered habitable spaces. (Mod CA5725 / AM) (Mod CA5188 / AM)
HEIGHT, THRESHOLD BUILDING. The height of the building is at the mean distance between the eaves and the ridge of the roofing structure. If the distance from grade to the line which is the mean distance between the eaves and the ridge of the roofing structure is more than 50 feet, the building is to be considered a "threshold building" within the contemplation of the Threshold Building Act. (Mod CA 5188 / AM)
HIGH VELOCITY HURRICANE ZONE. This zone consists of Broward and Dade counties. (Florida Specific Amendment)
HISTORIC BUILDINGS. Buildings that are listed in or eligible for listing in the National Register of Historic Places, or designated as historic under an appropriate state or local law (see Chapter 12 of the Florida Existing Building Code). (Mod CA 5188 / AM)
LANDSCAPE ARCHITECT. A Florida-registered landscape architect. (Mod CA 5188 / AM)
LOCAL FLOODPLAIN MANAGEMENT ORDINANCE. An ordinance or regulation adopted pursuant to the requirements in Title 44 Code of Federal Regulations, Parts 59 and 60 for participation in the National Flood Insurance Program. (Mod SP5259 / AS)
LOWEST FLOOR. The lowest floor of the lowest enclosed area, including basement, but excluding any unfinished or flood-resistant enclosure, usable solely for vehicle parking, building access or limited storage provided that such enclosure is not built so as to render the structure in violation of this section. 1612. (Mod SP5259 / AS)
MATERIAL CODE VIOLATION. A material code violation is a violation that exists within a completed building, structure or facility which may reasonably result, or has resulted, in physical harm to a person or significant damage to the performance of a building or its systems. (Mod CA5188 / AM)
MATERIAL VIOLATION. As defined in Florida Statutes. (Mod CA5188 / AM)
MAUSOLEUM. A permanent structure or building which is substantially exposed above the ground and is intended for the interment, entombment, or inurnment of human remains. (Florida Specific Amendment)
MEANS OF ESCAPE. As used in Section 1008.1.4.5, a way out of a building or structure that does not conform to the strict definition of means of egress but does provide an alternate way out. A means of escape consists of a door, stairway, passage or hall providing a way of unobstructed travel to the outside at street or ground level. It may also consist of a passage through an adjacent non-lockable space, independent of and remotely located from the means of egress, to any approved exit. (Mod F5716-R1 / AM)
NICHE. A permanent chamber in a columbarium or mausoleum to hold the cremated remains of one or more individuals.
NON-VISITATION CRYPT MAUSOLEUM. A mausoleum for the public where the crypts are not accessible to the public. (Florida Specific Amendment)
PLANS. All construction drawings and specifications for any structure necessary for the building official to review in order to determine whether a proposed structure, addition or renovation will meet the requirements of this code and other applicable codes. (Mod CA5188 / AM)
REGISTERED TERMITICIDE. Product listed as registered for use as a preventative treatment for termites for new construction by the Florida Department of Agriculture and Consumer Services under authority of Chapter 487, Florida Statutes. (Florida Specific Amendment)
SCREEN ENCLOSURE. A building or part thereof, in whole or in part self-supporting, and having walls of insect screening with or without removable vinyl or acrylic wind break panels and a roof of insect screening, plastic, aluminum or similar lightweight material, or other materials and assemblies such as a patio or deck roof of a structure. (Mod S5726 / AS)
SEPARATE ATMOSPHERE. The atmosphere that exists between rooms, spaces, or areas that are separated by an approved smoke barrier. (Mod F5191 / AS)
SKYLIGHTS AND SLOPED GLAZING. Glass or other transparent or translucent glazing material installed at a slope of 15 degrees (0.26 rad) or more from vertical. Glazing material in skylights, including unit skylights, tubular daylighting devices, solariums, sunrooms, roofs and sloped walls, are included in this definition. (S5633 AS). (S5635 AS) (S5636-R1 / AM)
SPECIAL INSPECTION. Reserved. Inspection of construction requiring the expertise of an approved special inspector in order to ensure compliance with this code and the approved construction documents.
Continuous Special Inspection. Special inspection by the special inspector who is present when and where the work to be inspected is being performed.
Periodic Special Inspection. Special inspection by the special inspector who is intermittently present where the work to be inspected has been or is being performed. (Mod CA5188 / AM) (Mod S5149 / AM)
SPECIAL INSPECTOR. Reserved. A qualified person employed or retained by an approved agency and approved by the building official as having the competence necessary to inspect a particular type of construction requiring special inspection. (Mod S5149 / AM)
STATE ENFORCEMENT AGENCY. Means the agency of state government with authority to make inspections of buildings and to enforce the codes, as required by this part, which establish standards for design, construction, erection, alteration, repair, modification or demolition of public or private buildings, structures or facilities. (Florida Specific Amendment)
STRUCTURAL DETERMINATION. For purposes of this code, "structural“ shall mean any part, material or assembly of a building or structure which affects the safety of such building or structure and/or which supports any dead or designed live load and the removal of which part, material or assembly could cause, or be expected to cause, all or any portion to collapse or fail. (Mod CA5188 / AM)
STRUCTURAL OBSERVATION. Reserved. The visual observation of the structural system by a registered design professional for general conformance to the approved construction documents. Structural observation does not include or waive the responsibility for the inspection required by Section 110, 1705 or other sections of this code. (Mod CA5188 / AM) (Mod S5149 / AM)
SUBSTANTIAL IMPROVEMENT. Any repair, reconstruction, rehabilitation, alteration, addition or other improvement of a building or structure, the cost of which equals or exceeds 50 percent of the market value of the structure before the improvement or repair is started. If the structure has sustained substantial damage, any repairs are considered substantial improvement regardless of the actual repair work performed. The term does not, however, include either:
1. Any project for improvement of a building required to correct existing health, sanitary or safety code violations identified by the building official and that are is the minimum necessary to assure safe living conditions.
2. Any alteration of a historic structure provided that the alteration will not preclude the structure’s continued designation as a historic structure. (Mod SP5259 / AS)
SUNROOM.
1. A one-story structure attached to a building with a glazing area in excess of 40 percent of the gross area of the structure’s exterior walls and roof.
2. A one-story structure added to a dwelling with solid roof panels without sloped glazing. The sunroom walls may have any configuration, provided the open areas with operable or fixed glass or windows or side hinged or sliding glass doors of the longer wall and one additional wall is equal to at least 65 percent of the area below 6 foot 8 inches (2032 mm) of each wall, measured from the floor. For the purposes of this code the term sunroom as used herein shall include conservatories, sunspaces, solariums, and porch or patio covers or enclosures. (Mod S5727 / AS)
TECHNICALLY INFEASIBLE. An alteration of a building or a facility that has little likelihood of being accomplished because the existing structural conditions require the removal or alteration of a load-bearing member that is an essential part of the structural frame, or because other existing physical or site constraints prohibit modification or addition of elements, spaces or features which are in full and strict compliance with the minimum requirements for new construction and which are necessary to provide accessibility. See the Florida Building Code, Accessibility. (Mod A5104 / AM)
THRESHOLD BUILDING. In accordance with Florida Statute, any building which is greater than 3 stories or 50 feet in height, or which has an assembly occupancy classification that exceeds 5,000 square feet in area and an occupant content of greater than 500 persons. (Mod CA5188 / AM)
TOWNHOUSE. A single-family dwelling unit constructed in a group of three or more attached units with property lines separating each unit in which each unit extends from foundation to roof and with open space on at least two sides. (Mod F5191 / AS)
VALUE. The estimated current replacement cost of the building in kind. (Mod CA5188 / AM)
WHEELCHAIR SPACE. A space for a single wheelchair and its occupant. See the Florida Building Code, Accessibility. (Mod A5104-R1 / AM)
Chapter 3 – Use and Occupancy Classification
Florida Specific Amendment
Section 304 – Business Group B
Add Section 304 to read as shown:
304.3 Public and private colleges and universities shall comply with Section 468.
304.4 Florida colleges shall comply with Section 453.
Florida Specific Amendment
Section 305 – Educational Group E
Add Section 305 to read as shown:
305.3 Public and private educational occupancies shall comply with Section 443.
305.4 Public education occupancies shall comply with Section 453.
Section 307 – High-hazard Group H
Change Section 307.1 to read as shown:
307.1 High-hazard Group H. High-hazard Group H occupancy includes, among others, the use of a building or structure, or a portion thereof, that involves the manufacturing, processing, generation or storage of materials that constitute a physical or health hazard in quantities in excess of those allowed in control areas complying with Section 414, based on the maximum allowable quantity limits for control areas set forth in Tables 307.1(1) and 307.1(2). Hazardous occupancies are classified in Groups H-1, H-2, H-3, H-4 and H-5 and shall be in accordance with this section, the requirements of Section 415 and the International Fire Code Florida Fire Prevention Code. Hazardous materials stored, or used on top of roofs or canopies shall be classified as outdoor storage or use and shall comply with the International Fire Code Florida Fire Prevention Code.
Exceptions: The following shall not be classified in Group H, but shall be classified in the occupancy that they most nearly resemble:
1. – 13. (No Change)
14. Mercantile occupancies offering for retail sale sparklers, novelties and trick noisemakers as defined at Section 791.01, Florida Statutes, and that are not defined as fireworks by Chapter 791, Florida Statutes. Storage of sparklers and other novelties or trick noisemakers as defined in Chapter 791, Florida Statutes, within mercantile occupancies shall be in accordance with Section 791.055, Florida Statutes.
(Mod F5105 / AS)
Chapter 4 – Special Detailed Requirements Based on Use and Occupancy
(See Attached Chapter 4 changes)
Chapter 5 – General Building Heights and Areas
Section 505 – Mezzanines and Equipment Platforms
Change Section 505.2.1 to read as follows:
505.2.1 Area limitation. (No Change)
Exceptions:
1. – 2. (No Change)
3. In sprinklered Group S2 occupancies of Type III construction, the enclosed and unenclosed areas under mezzanines shall be allowed to be included when calculating the permissible size of mezzanines.
(Mod F5106 / AS)
Florida Specific Amendment
Section 507 – Group E Buildings
Change Section 507.10 to read as shown:
507. 10 Group E buildings. The area of a Group E building no more than one story above grade plane, of Type II, IIIA or IV construction, shall not be limited provided all of the following criteria are met:
1. Each classroom shall have not less than two means of egress, with one of the means of egress being a direct exit to the outside of the building complying with Section 1020 or the building is provided with smoke barriers having a minimum 1-hour fire-resistance rating dividing the building into areas not to exceed 30,000 square feet (2,787 m2) in floor area.
2. – 3. (No change)
Section 510 – Special Provisions
Change Section 510.4 to read as follows:
510.4 Parking beneath Group R. Where a maximum one-story above grade plane Group S-2 parking garage, enclosed or open, or combination thereof, of Type I construction or open of Type IV construction, with grade entrance, is provided under a building of Group R, the number of stories to be used in determining the minimum type of construction shall be measured from the floor above such a parking area. The number of stories to be used in determining the height in stories in accordance with Section 903.2.11.3 903.6 shall include the parking garage as a story. The floor assembly between the parking garage and the Group R above shall comply with the type of construction required for the parking garage and shall also provide a fire-resistance rating not less than the mixed occupancy separation required in Section 508.4.
(Mod F5107 / AS)
Chapter 6 – Types of Construction
(No Change)
Chapter 7 – Fire and Smoke Protection Features
Section 706 – Fire Walls
Add Section 706.4.1 to read as follows:
706.4.1 Townhouse fire separation.
706.4.1.1 Each townhouse shall be considered a separate building and shall be separated from adjoining townhouses by a party wall complying with Section 706.1.1 or by the use of separate exterior walls meeting the requirements of Tables 601 and 602 for zero clearance from property lines as required for the type of construction. Separate exterior walls shall include one of the following:
1. A parapet not less than 18 inches (457 mm) above the roof line.
2. Roof sheathing of noncombustible material or fire retardant treated wood, for not less than a 4 foot (1219 mm) width on each side of the exterior dividing wall.
3. One layer of 5/8 inch (15.9 mm) Type X gypsum board attached to the underside of roof decking, for not less than a 4 foot (1219 mm) width on each side of the exterior dividing wall.
706.4.1.2 When not more than three stories in height, townhouses may be separated by a single wall meeting the following requirements:
1. Such wall shall provide not less than a 2-hour fire-resistance rating. Plumbing, piping, ducts, electrical or other building services shall not be installed within or through the 2-hour wall, unless such materials and methods of penetration have been tested in accordance with Section 703.
2. Such wall shall be continuous from the foundation to the underside of no less than a 4-foot (1219 mm) width on each side of the wall shall be of noncombustible material, or fire-retardant-treated wood, or one layer of 5/8-inch (15.9 mm) Type X gypsum wallboard attached to the underside of the roof decking.
3. Each dwelling unit sharing such wall shall be designed and constructed to maintain its structural integrity independent of the unit on the opposite side of the wall.
Exception: Said wall may be penetrated by roof and floor structural members provided that the fire-resistance rating and the structural integrity of the wall is maintained.
(Mod F5108 / AS)
Section 708 – Fire Partitions
Change Section 708.3 to read as follows:
708.3 Fire resistance rating. Fire partitions shall have a fire-resistance rating of not less than 1 hour.
Exceptions:
1. – 2. (No Change)
3. In mini-warehouses/self-storage buildings, walls used to separate tenants shall not be required to have fire-resistance rating, provided a sprinkler system meeting the requirements of Ordinary Hazard Group II as defined by NFPA 13, is installed employing quick response heads.
(Mod F5109 / AS)
Chapter 8 – Interior Finishes
(No Change)
Chapter 9 – Fire Protection Systems
Section 901 - General
Change Section 901.1 to read as follows:
901.1 Scope. The provisions of this chapter shall specify where fire protection systems are required and shall apply to the design, installation and operation of fire protection systems and carbon monoxide detection alarms.
(Mod F5110 / AS)
Florida Specific Amendment
Section 903 – Automatic Sprinkler Systems
Change Section 903.2.3 to read as shown:
903.2.3 Group E. An automatic sprinkler system shall be provided for Group E occupancies as follows:
1.– 2. (No change)
Exception: An automatic fire sprinkler system is not required in any area below the lowest level of exit discharge serving that area where every classroom throughout the building has at least one exterior exit door at ground level. existing educational buildings unless 50 percent of the aggregate area of the building is being remodeled.
Section 903 – Automatic Sprinkler Systems
Change Section 903.2.11.3 to read as follows:
903.2.11.3 Buildings over 55 feet in height. Buildings three stories or more in height. An automatic sprinkler system shall be installed throughout buildings with a floor level having an occupant load of 30 or more that is located 55 feet (16 764 mm) or more above the lowest level of fire department vehicle access. Any building which is of three stories or more in height shall be equipped with an approved automatic sprinkler system installed in accordance with Section 903.1.
Exceptions:
1. Airport control towers. Single- and two-family dwellings.
2. Open parking structures. A stand-alone parking garage constructed with noncombustible materials, the design of which is such that all levels of the garage are uniformly open to the atmosphere on all sides with the percentages of openings equal to or greater than those specified in Section 406.3. Such garages shall be separated from any other structure by not less than 20 feet (6096 mm). A stand-alone parking garage is one that is solely for the parking of vehicles and does not have any other occupancy group in the building.
3. Occupancies in Group F-2. Telecommunication spaces located within telecommunication buildings, if the spaces are equipped to meet an equivalent fire prevention standard approved by both the Florida Building Commission and the State Fire Marshal.
4. Telecommunications spaces within telecommunication buildings, if the telecommunications space is equipped with:
4.1. Air sampling smoke detection.
4.2. Remote, proprietary or central station fire alarm monitoring.
4.3. Automatic smoke exhaust system.
4.4. One-hour fire-resistance wall separating the telecommunications space from the adjacent areas on the same floor.
4.5. Two-hour floor/ceiling assembly separating the telecommunications space from adjacent floors.
4.6. All other portions ancillary to the telecommunications equipment area shall be provided with fire sprinkler protection.
5. Sprinkler systems installed solely as a requirement of Section 903.62.11.3 may be a NFPA 13R or NFPA 13D system in accordance with their scopes.
903.2.11.3.1 NFPA 101 as adopted by Florida Fire Prevention Code, as regarding the requirements for fire protection sprinklers, is applicable to all multiple-family residential buildings, whether designated as townhouses, condominiums, apartment houses, tenements, garden apartments or by any other name. The attorney general has determined that for the purpose of the fire protection sprinkler requirements in Section 553.895(2), Florida Statutes, townhouses that are three or more stories tall and consist of three or more units together are multiple-family dwellings. Therefore, these types of townhouses are not exempt from being considered for the requirements to provide fire protection sprinklers (even if there are any other definitions that define a townhouse as a single-family residence). When determining whether townhouses require fire protection sprinkler systems, the building official must consider in parallel: (a) the attorney general’s opinion defining the statutory language for townhouses; (b) the building code requirements, including all life-safety chapters, that provide additional determining criteria, such as construction types, fire-resistance, fire protection systems and egress; and (c) the NFPA 101 as adopted by Florida Fire Prevention Code, egress and protection determining criteria. The more restrictive criteria are then applied.
(Mod F5111 / AS)
Section 907 – Fire Alarm and Detection Systems
Add Sections 907.1.4 and 907.9 to read as follows:
907.1.4 Accessibility. Every required fire alarm system shall include a visible alarm indicating appliances in public and common areas. For more specific accessibility requirements related to alarm indicating appliances, refer to Section 11-4.28. applicable sections of the Florida Building Code, Accessibility
Add Section 907.9 to read as follows:
907.9 Accessibility. Alarm systems required to be accessible shall comply with the applicable sections of the Florida Building Code, Accessibility
(Mod A5112 / AS)
Section 908 – Carbon Monoxide Protection
Add Section 908.7 to read as follows:
908.7 Carbon monoxide alarms. Group I or R occupancies located in a building containing a fuel-burning appliance or in a building which has an attached garage shall be equipped with single-station carbon monoxide alarms. The carbon monoxide alarms shall be listed as complying with UL 2034 and be installed and maintained in accordance with NFPA 720 and the manufacturer’s instructions. An open parking garage, as defined in Chapter 2, or an enclosed parking garage ventilated in accordance with Section 404 of the International Mechanical Code shall not be considered an attached garage. Carbon monoxide protection. Every separate building or an addition to an existing building for which a permit for new construction is issued and having a fossil-fuel-burning heater or appliance, a fireplace, an attached garage, or other feature, fixture, or element that emits carbon monoxide as a byproduct of combustion shall have an operational carbon monoxide alarm installed within 10 feet of each room used for sleeping purposes in the new building or addition, or at such other locations as required by this Code.
Exception: Sleeping units or dwelling units which do not themselves contain a fuel-burning appliance or have an attached garage, but which are located in a building with a fuel-burning appliance or an attached garage, need not be equipped with single-station carbon monoxide alarms provided that:
1. The sleeping unit or dwelling unit is located more than one story above or below any story which contains a fuel-burning appliance or an attached garage;
2. The sleeping unit or dwelling unit is not connected by duct work or ventilation shafts to any room containing a fuel-burning appliance or to an attached garage; and
3. The building is equipped with a common area carbon monoxide alarm system.
908.7.1 Carbon monoxide detection systems. Carbon monoxide detection systems, which include carbon monoxide detectors and audible notification appliances, installed and maintained in accordance with this section for carbon monoxide alarms and NFPA 720 shall be permitted. The carbon monoxide detectors shall be listed as complying with UL 2075. 916.1.1 Carbon monoxide alarm. The requirements of Section 908.7 shall be satisfied by providing for one of the following alarm installations:
1. A hard-wired carbon monoxide alarm.
2. A battery-powered carbon monoxide alarm.
3. A hard-wired combination carbon monoxide and smoke alarm.
4. A battery-powered combination carbon monoxide and smoke alarm.
908.7.2 Combination alarms. Combination smoke/carbon monoxide alarms shall be listed and labeled by a Nationally Recognized Testing Laboratory.
Exceptions:
1. An approved operational carbon monoxide detector shall be installed inside or directly outside of each room or area within a hospital, inpatient hospice facility or nursing home facility licensed by the Agency for Health Care Administration, or a new state correctional institution where a fossil-fuel burning heater, engine, or appliance is located. The carbon monoxide detector shall be connected to the fire-alarm system of the hospital, inpatient hospice facility, or nursing home facility as a supervisory signal.
2. This section shall not apply to existing buildings that are undergoing alterations or repair unless the alteration is an addition as defined in Section 908.7.3 916.1.3.
908.7.3 Addition shall mean an extension or increase in floor area, number of stories or height of a building or structure.
(Mod F5113-R1 / AM)
Chapter 10 – Means of Egress
Section 1002 - Definitions
Change Section 1002.1 to add definition as follows:
1002.1 Definitions. The following terms are defined in Chapter 2:
Means of Escape
(Mod F5638 / AS)
Section 1003 – General Means of Egress
Add Section 1003.5.1 to read as follows:
1003.5.1 Accessibility. For accessibility provisions related to changes in levels, see the Florida Building Code, Accessibility.
(Mod A5114 / AS)
Section 1007 – Accessible Means of Egress
Change Section 1007.1 to read as shown:
1007.1 Accessible means of egress required. Accessible means of egress shall be provided in accordance with the applicable sections of the Florida Building Code, Accessibility. comply with this section. Accessible spaces shall be provided with not less than one accessible means of egress. Where more than one means of egress are required by Section 1015.1 or 1021.1 from any accessible space, each accessible portion of the space shall be served by not less than two accessible means of egress.
Exceptions:
1. Accessible means of egress are not required in alterations to existing buildings.
2. One accessible means of egress is required from an accessible mezzanine level in accordance with Section 1007.3, 1007.4 or 1007.5.
3. In assembly areas with sloped or stepped aisles, one accessible means of egress is permitted where the common path of travel is accessible and meets the requirements in Section 1028.8.
Change Section 1007.2 to read as shown:
1007.2 Continuity and components. Reserved.
Change Section 1007.3 to read as shown:
1007.3 Stairways. Reserved.
Change Section 1007.4 to read as shown:
1007.4 Elevators. Reserved.
Change Section 1007.5 to read as shown:
1007.5 Platform lifts. Reserved.
Change Section 1007.6 to read as shown:
1007.6 Areas of refuge. Reserved.
Change Section 1007.7 to read as shown:
1007.7 Exterior area for assisted rescue. Reserved.
Change Section 1007.8 to read as shown:
1007.8 Two-way communication. Reserved.
Change Section 1007.9 to read as shown:
1007.9 Signage. Reserved.
Change Section 1007.10 to read as shown:
1007.10 Directional signage. Reserved.
Change Section 1007.11 to read as shown:
1007.11 Instructions. Reserved.
(Mod A5115 / AS)
Section 1008 – Doors, Gates and Turnstiles
Change Section 1008.1 to read as shown:
1008.1 Doors. Means of egress doors shall meet the requirements of this section. Doors serving a means of egress system shall meet the requirements of this section and Section 1020.2. Doors provided for egress purposes in numbers greater than required by this code shall meet the requirements of this section. For accessibility provisions related to doors, refer to the Florida Building Code, Accessibility.
Means of egress doors shall be readily distinguishable from the adjacent construction and finishes such that the doors are easily recognizable as doors. Mirrors or similar reflecting materials shall not be used on means of egress doors. Means of egress doors shall not be concealed by curtains, drapes, decorations or similar materials.
(Mod A5117 / AS)
Section 1008 – Doors, Gates and Turnstiles
Change Section 1008.1.1 to read as shown:
1008.1.1 Size of doors. (No change to main body of text)
Exceptions:
1. – 6. (No change)
7. In other than Group R-1 occupancies, the minimum widths shall not apply to interior egress doors within a dwelling unit or sleeping unit that is not required to be an Accessible unit, Type A unit or Type B unit.
8. Door openings required to be accessible within Type B units shall have a minimum clear width of 31.75 inches (806 mm).Buildings that are 400 square feet or less and that are intended for use in conjunction with one- and two-family residences are not subject to the door height and width requirements of this code.
(Mod SP5120 / AS)
Section 1008 – Doors, Gates and Turnstiles
Add Section 1008.1.4.5 to read as shown:
1008.1.4.5 Protection devices for emergency escape and rescue openings. The temporary installation or closure of storm shutters, panels and other approved hurricane protection devices shall be permitted on emergency escape and rescue openings in Group R occupancies during the threat of a storm. Such devices shall not be required to comply with the operational constraints of Section 1029.4. While such protection is provided, at least one means of escape from the dwelling or dwelling unit shall be provided. The means of escape shall be within the first floor of the dwelling or dwelling unit and shall not be located within a garage without a side hinged door leading directly to the exterior. Occupants in any part of the dwelling or dwelling unit shall be able to access the means of escape without passing through a lockable door not under their control.
(Mod F5640 / AS)
Section 1008 – Doors, Gates and Turnstiles
Change Section 1008.1.7 to read as shown:
1008.1.7 Thresholds. Thresholds at doorways shall not exceed 3/4 inch (19.1 mm) in height above the finished floor or landing for sliding doors serving dwelling units or 1/2 inch (12.7 mm) above the finished floor or landing for other doors. Raised thresholds and floor level changes greater than 1/4 inch (6.4 mm) at doorways shall be beveled with a slope not greater than one unit vertical in two units horizontal (50-percent slope).
Exceptions: In occupancy Group R-2 or R-3, threshold heights for sliding and side- hinged exterior doors shall be permitted to be up to 73/4 inches (197 mm) in height if all of the following apply:
1. The door is not part of the required means of egress. The threshold height shall be limited to 73/4 inches (197 mm) where the occupancy is Group R-2; the door is an exterior door that is not a component of the required means of egress and the doorway is not on an accessible route. In one- and two-family dwellings where the door discharges to the outside or to an exterior balcony or exterior exit access, the floor level outside the door shall be permitted to be one step lower than the inside, but not more than 8 inches (203 mm) lower.
2. The door is not part of an accessible route as required by Chapter 11. For exterior doors serving dwelling units, thresholds at doorways shall not exceed the height required to pass the water resistance test of ANSI/AAMA/WDMA 101/I.S.2, or TAS 202 for high- velocity hurricane zones, or the maximum allowable height difference between interior floor levels. Exterior floor level shall comply with the following:
|LEVEL DIFFERENCE |AT PRIMARY DOOR |
|(inches) | |
|0 |Pervious construction |
| |(e.g., wood decking with spaces) |
|1/2 |Impervious construction |
| |(e.g., concrete, brick or flag stone) |
|LEVEL DIFFERENCE |AT SECONDARY DOOR |
|(inches) | |
|1/2 |Pervious construction |
|4 |Impervious construction |
3. The door is not part of an Accessible unit, Type A unit or Type B unit.
(Mod F5719 – R1 / AM)
Section 1009 – Stairways
Change Section 1009.1 to read as follows:
1009.9.1 Stairway walking surface. The walking surface of treads and landings of a stairway shall not be sloped steeper than one unit vertical in 48 units horizontal (2-percent slope) in any direction. Stairway treads and landings shall have a solid surface. Finish floor surfaces shall be securely attached.
Exceptions:
(1-2 No change)
3. See also the Florida Building Code, Accessibility.
(Mod A5126 / AS)
Section 1009 – Stairways
Add Section 1009.18 to read as shown:
1009.18 Accessible stairs. Stairs required to be accessible shall comply with the Florida Building Code, Accessibility.
(Mod A5127 / AS)
Section 1010 – Ramps
Change Section 1010.1 to read as shown:
1010.1 Scope. The provisions of this section shall apply to ramps used as a component of a means of egress.
1010.1 Exceptions:
1. Other than ramps that are parts of accessible routes providing access in accordance with Sections 1108.2 through 1108.2.4 and 1108.2.6 the provisions of the Florida Building Code, Accessibility, ramped aisles within assembly rooms or spaces shall conform to the provisions in 1028.11
2. Curb ramps not subject to Florida Building Code, Accessibility, shall comply with ICC ANSI A117.1.
3. Vehicle ramps in parking garages for pedestrian exit access shall not be required to comply with Sections 1010.4 through 1010.10 the provisions of the Florida Building Code, Accessibility when they are not an accessible route serving accessible parking spaces, other required accessible elements, or part of an accessible means of egress.
(Mod A5128-R1 / AM)
Section 1010 – Ramps
Change Section 1010.4 to read as shown:
1010.3 4 Cross slope. The slope measured perpendicular to the direction of travel of a ramp shall not be steeper than one unit vertical in 48 units horizontal (2-percent slope).
Exception: See also the Florida Building Code, Accessibility.
(Mod A5129 / AS)
Section 1010 – Ramps
Change Section 1010.7 to read as shown:
1010.7 Landings. Ramps shall have landings at the bottom and top of each ramp, points of turning, entrance, exits, and at doors and in accordance with the Florida Building Code, Accessibility. Landings shall comply with Sections 1010.67.1 through 1010.7.5.
Change Section 1010.7.1 to read as shown:
1010.7.1 Slope. Landings shall have a slope not steeper than one unit vertical in 48 units horizontal (2-percent slope) in any direction. Changes in level are not permitted.
Exception: see also the Florida Building Code, Accessibility.
Change Section 1010.7.3 to read as shown:
1010.7.3 Length. The landing length shall be 60 inches (1525 mm) minimum.
Exceptions:
1. In Group R-2 and R-3 individual dwelling and sleeping units that are not required to be Accessible units, Type A units or Type B units in accordance with Section 1107 landings are permitted to be 36 inches (914 mm) minimum.
2. (No change)
3. Accessible landings shall comply with the Florida Building Code, Accessibility.
(Mod A5130 / AS)
Section 1010 – Ramps
Change Section 1010.10 to read as shown:
1010.10 Edge protection. Edge protection complying with Sections 1010.10.1 or 1010.109.2 shall be provided on each side of ramp runs and at each side of ramp landings.
Exceptions:
1. Edge protection is not required on ramps not required to have handrails, provided they have flared sides that comply with the ICC A117.1 curb ramp provisions of the Florida Building Code, Accessibility.
2 – 4 No change.
(Mod A5132 / AS)
Section 1012 – Handrails
Change Section 1012.3 to read as shown:
1012.3 Handrail graspability. All required handrails shall comply with Section 1012.3.1 or shall provide equivalent graspability.
Exceptions:
1. In Group R-3 occupancies; within dwelling units in Group R-2 occupancies; and in Group U occupancies that are accessory to a Group R-3 occupancy or accessory to individual dwelling units in Group R-2 occupancies; handrails shall be Type I in accordance with Section 1012.3.1, Type II in accordance with Section 1012.3.2 or shall provide equivalent graspability.
2. Accessible handrails shall meet the requirements of the Florida Building Code, Accessibility.
(Mod A5133 / AS)
Section 1012 – Handrails
Change Section 1012.6 to read as shown:
1012.6 Handrail extensions. Handrails shall return to a wall, guard or the walking surface or shall be continuous to the handrail of an adjacent stair flight or ramp run. Where handrails are not continuous between flights, the handrails shall extend horizontally at least 12 inches (305 mm) beyond the top riser and continue to slope for the depth of one tread beyond the bottom riser. At ramps where handrails are not continuous between runs, the handrails shall extend horizontally above the landing 12 inches (305 mm) minimum beyond the top and bottom of ramp runs. The extensions of handrails shall be in the same direction of the stair flights at stairways and the ramp runs at ramps.
Exceptions:
1. – 3. (No change)
4. Accessible handrail extensions shall be as per the Florida Building Code, Accessibility.
(Mod A5134 / AS)
Section 1015 - Exit and Exit Access Doorways
Change Section 1015.1 to read as shown:
1015.1 Exits or exit access doorways from spaces. Two exits or exit access doorways from any space shall be provided where one of the following conditions exists:
1. The occupant load of the space exceeds one of the values in Table 1015.1.
Exceptions:
1. In Group R-2 and R-3 occupancies, one means of egress is permitted within and from individual dwelling units with a maximum occupant load of 20 where the dwelling unit is equipped throughout with an automatic sprinkler system in accordance with Section 903.3.1.1 or 903.3.1.2. Reserved
2. Care suites in Group I-2 occupancies complying with Section 407.4.3.
2. The common path of egress travel exceeds one of the limitations of Section 1014.3.
3. Where required by Section 1015.3, 1015.4, 1015.5, or 1015.6.
Where a building contains mixed occupancies, each individual occupancy shall comply with the applicable requirements for that occupancy. Where applicable, cumulative occupant loads from adjacent occupancies shall be considered in accordance with the provisions of Section 1004.1.
TABLE 1015.1
SPACES WITH ONE EXIT OR EXIT ACCESS DOORWAY
|OCCUPANCY |MAXIMUM OCCUPANT LOAD |
|A,B, E,F,M,U, R2, R3 |49 |
|H-1,H-2,H-3 |3 |
|H-4, H-5, I-1, I-3, I-4, R R-1, R-4 |10 |
|S |29 |
Change Section 1015.2.1 to read as shown:
1015.2.1 Two exits or exit access doorways. (No Change)
.Exceptions:
1. – 2. ( No change.)
3. In Group R1 and R2 occupancies, the distance between exits is not applicable to common nonlooped exit access corridors in a building that has corridor doors from the guestroom or guest suite or dwelling unit, which are arranged so that the exits are located in opposite directions from such doors.
(Mod A5985-R1 / AM)
Section 1029 – Emergency Escape and Rescue
Change Section 1029.1 to read as shown:
1029.1 General. In addition to the means of egress required by this chapter, provisions shall be made for emergency escape and rescue openings in Group R-2 occupancies in accordance with Tables 1021.2(1) and 1021.2(2) and Group R-3 occupancies. Basements and sleeping rooms below the fourth story above grade plane shall have at least one exterior emergency escape and rescue opening in accordance with this section. Where basements contain one or more sleeping rooms, emergency escape and rescue openings shall be required in each sleeping room, but shall not be required in adjoining areas of the basement. Such openings shall open directly into a public way or to a yard or court that opens to a public way.
Exceptions:
1. Basements with a ceiling height of less than 80 inches (2032 mm) shall not be required to have emergency escape and rescue openings.
2. Emergency escape and rescue openings are not required from basements or sleeping rooms that have an exit door or exit access door that opens directly into a public way or to a yard, court or exterior exit balcony that opens to a public way.
3. Basements without habitable spaces and having no more than 200 square feet (18.6 m2) in floor area shall not be required to have emergency escape and rescue openings.
4. Security and hurricane devices installed in accordance with Section 1008.1.4.5.
(Mod A5796 / AS)
Chapter 11 – Accessibility
Florida Specific Amendment
Section 1101 – General
Change Section 1101.1 to read as shown:
1101.1 Scope. The provisions of this chapter shall control the design and construction of facilities for accessibility to physically disabled persons. This chapter governs the design and construction of buildings for accessibility.
1101.1.1 Criteria. Buildings shall be designed and constructed in accordance with the Florida Building Code, Accessibility.
Chapter 12 – Interior Environment
(No change)
Chapter 13 – Energy Efficiency
Florida Specific Amendment
Section 1301 – Energy Efficiency
Change Section 1301.1 to read as shown:
1301.1.1 Criteria. Buildings shall be designed and constructed in accordance with the International Energy Conservation Code. Florida Building Code, Energy Conservation.
Chapter 14 – Exterior Walls
Section 1401 – General
Change Section 1401.1 to read as shown:
1401.1 Scope. The provisions of this chapter shall establish the minimum requirements for exterior walls, exterior wall coverings, exterior wall openings, exterior windows and doors, architectural trim, balconies and similar projections; and bay and oriel windows.
Exception: Buildings and structures located within the high-velocity hurricane zone shall comply with the provisions of Sections 1403.8 and 1410.
(Mod S4926 / AS)
Section 1403 – Performance Requirements
Change Section 1403.7 to read as shown:
1403.7 Flood resistance for velocity wave action areas coastal high hazard areas. For buildings in flood hazard areas subject to high-velocity wave action coastal high hazard areas as established in Section 1612.3, electrical, mechanical and plumbing system components shall not be mounted on or penetrate through exterior walls that are designed to break away under flood loads.
(Mod SP5274 / AS)
Florida Specific Amendment
Section 1403 – Performance Requirements
Add Section 1403.8 to read as shown:
1403.8 In order to provide for inspection for termite infestation, clearance between exterior wall coverings and final earth grade on the exterior of a building shall not be less than 6 inches (152 mm).
Exceptions:
1. Paint or decorative cementitious finish less than 5/8 inch (17.1 mm) thick adhered directly to the masonry foundation sidewall.
2. Access or vehicle ramps which rise to the interior finish floor elevation for the width of such ramps only.
3. A 4-inch (102 mm) inspection space above patio and garage slabs and entry areas.
4. If the patio has been soil treated for termites, the finish elevation may match the building interior finish floor elevations on masonry construction only.
5. Masonry veneers constructed in accordance with Section 2114.2.
Section 1404 – Materials
Change Section 1404.5 to read as shown:
1404.5 Metal. Exterior walls of formed steel construction, structural steel or lightweight metal alloys shall be designed in accordance with Chapters 22 and 20, respectively.
1404.5.1 Aluminum siding. Aluminum siding shall conform to the requirements of AAMA 1402 and TAS 202 and 203 in the HVHZ. (Mod S4801 / AS)
AAMA 1402, shall be modified to read as follows:
Section 1 Standard Specifications for Aluminum Siding, Soffit, and Fascia, 2.0 Siding Specifications, 2.2 Performance Criteria, 2.2.1 Windload Resistance
2.2.1.1 Static Pressure Test
2.2.1.1.1All siding products shall be capable of resisting the design pressures specified for walls for components and cladding loads in accordance with Section 1609.1.1. To verify that the siding will perform under these conditions, it shall be tested in accordance with Test Method #1, “Standard for Testing of Aluminum Siding/Fastener for Windload Resistance” or in an approved manner. The static test pressure shall be as required to demonstrate compliance with the provisions of Section 1609.1.
2.2.1.1.2 For applications where the effective design pressure as specified in Section 1609.1.1 is greater than 1040 Pa(21.7 psf) [e.g. wind zone areas greater than 36 m/s (80 mph) or elevations above 33 feet (10 m)] the product shall b tested in accordance with Test Method #1 under a static test pressure determined by the formula:
PT = 1.5 × DP
Where:
PT = Static Test Pressure [Pa (psf)]
DP = Design Pressure [Pa (psf)]
1.5 = Safety Factor
* Delete Section 2.2.1.2 and corresponding table.
Strike Table:
See uploaded support file for table.
3.0
Soffit and Fascia Specifications, 3.2 Performance Criteria, 3.2.1 Windload Resistance
3.2.1.1 Static Pressure Test
3.2.1.1.1 All soffit products shall be capable of resisting the design pressures specified for walls for components and cladding loads in accordance with Section 1609.1.1. To verify that the soffit will perform under these conditions, it shall be tested in the maximum unsupported length for which the manufacturer seeks conformance when tested in accordance with Test Method #4, “Standard for Testing of Soffits and Windload Resistance.”
The static test pressure shall be as required to demonstrate compliance with the provisions of Section 1609.1.
3.2.1.1.2 For applications where the effective design pressure as specified in Section 1609.1.1 is greater than 1040 Pa (21.7 psf) [e.g. wind zone areas greater than (80 mph) 36 m/s or elevations above (33 ft.) 10 m] the product shall be tested in accordance with Test Method #4 under a static test pressure determined by the formula:
PT = × 1.5 × DPp
Where:
PT = Static Test Pressure [Pa (psf)]
DPp = Design Pressure [Pa (psf)]
1.5 = Safety Factor
Section 3, Appendix, Windload Criteria is deleted in its entirety.
(Mod S5728 / AS)
(Mod S4801 / AS)
Section 1404 – Materials
Add Section 1404.13 to read as shown:
1404.13 Manufactured soffit materials and systems shall be labeled in accordance with the provisions of Section 1710.9 of this code.
(Mod S5733 / AS)
Section 1405 – Installation of Wall Coverings
Change Section 1405.1 to read as shown:
1405.1 General. Exterior wall coverings shall be designed and constructed in accordance with the applicable provisions of this section and TAS 202 and 203 in the HVHZ.
(Mod S4931 / AS)
Section 1405 – Installation of Wall Coverings
Change Table 1405.2 to read as shown:
TABLE 1405.2
MINIMUM THICKNESS OF WEATHER COVERINGS
|COVERING TYPE |MINIMUM THICKNESS |
| |(inches) |
|Adhered masonry veneer |0.25 |
|Aluminum siding |0.019 |
|Anchored masonry veneer |2.625 |
|Asbestos-cement boards |0.125 |
|Asbestos shingles |0.156 |
|Cold-rolled copperd |0.0216 nominal |
|Copper shinglesd |0.0162 nominal |
|Exterior plywood (with sheathing) |0.313 |
|Exterior plywood (without sheathing) |See Section 2304.6 (HVHZ see Section 2315.2) |
|Fiber-cement lap siding |0.25c |
|Fiber-cement panel siding |0.25c |
|Fiberboard siding |0.5 |
|Glass-fiber reinforced concrete panels |0.375 |
|Hardboard sidingc |0.25 |
|High-yield copperd |0.0162 nominal |
|Lead-coated high-yield copper |0.0162 nominal |
|Marble slabs |1 |
|Particleboard (with sheathing) |See Section 2304.6 (HVHZ see Section 2315.1.11) |
|Particleboard (without sheathing) |See Section 2304.6 (HVHZ see Section 2315.1.11) |
|Precast stone facing |0.625 |
|Steel (approved corrosion resistant) |0.0149 |
|Stone (cast artificial) |1.5 |
|Stone (natural) |2 |
|Structural glass |0.344 |
|Stucco or exterior cement plaster | |
|Three-coat work over: | |
|Metal plaster base |0.875b |
|Unit masonry |0.625b |
|Cast-in-place or precast concrete |0.625b |
|Two-coat work over: | |
|Unit masonry |0.5b |
|Cast-in-place or precast concrete |0.375b |
|Terra cotta (anchored) |1 |
|Terra cotta (adhered) |0.25 |
|Vinyl siding |0.035 |
|Wood shingles |0.375 |
|Wood siding (without sheathing)a |0.5 |
|Lead-coated copperd |0.0216 nominal |
|For SI: 1 inch = 25.4 mm, 1 ounce per square foot = 0.305 kg/m2. |
|a. Wood siding of thicknesses less than 0.5 inch shall be placed over sheathing that conforms to Section 2304.6. (HVHZ see Section 2315.2) |
|b. Exclusive of texture. |
|c. As measured at the bottom of decorative grooves. |
|d. 16 ounces per square foot for cold-rolled copper and lead-coated copper, 12 ounces per square foot for copper shingles, high-yield |
|copper and lead-coated high-yield copper. |
|e. Includes scratch coat, setting bed, and precast stone. |
(Mod S4933 / AS)
Section 1405 – Installation of Wall Coverings
Change Section 1405.17 to read as shown:
1405.17 Fastening. Weather boarding and wall coverings shall be securely fastened with aluminum, copper, zinc, zinc-coated or other approved corrosion-resistant fasteners in accordance with the nailing schedule in Table 2304.9.1, the HVHZ shall comply with Table 2323.1 or the approved manufacturer's installation instructions. Shingles and other weather coverings shall be attached with appropriate standard-shingle nails to furring strips securely nailed to studs, or with approved mechanically bonding nails, except where sheathing is of wood not less than 1-inch (25 mm) nominal thickness or of wood structural panels as specified in Table 2308.9.3(3) (the HVHZ shall comply with Section 2322).
(Mod S4932 / AS)
Chapter 15 - Roof Assemblies and Rooftop Structures
Florida Specific Amendment
Section 1501 – General
change Section 1501.1 to read as shown:
1501.1 Scope. The provisions of this chapter shall govern the design, materials, construction and quality of roof assemblies, and rooftop structures.
Exception: Buildings and structures located within the high-velocity hurricane zone shall comply with the provisions of Section 1503.6 and Sections 1512 through 1525.
Section 1502 – Definitions
Change Section 1502.1 to read as shown:
1502.1 Definitions General. The following words and terms shall, for the purposes of this chapter and as used elsewhere in this code, have the meanings shown herein. The following terms are defined in Chapter 2:
AGGREGATE. In roofing, crushed stone, crushed slag or water-worn gravel used for surfacing for roof coverings.
BALLAST. In roofing, ballast comes in the form of large stones or paver systems or light-weight interlocking paver systems and is used to provide uplift resistance for roofing systems that are not adhered or mechanically attached to the roof deck.
BUILDING INTEGRATED PHOTOVOLTAIC ROOFING. A roofing product consisting of electricity generating photovoltaic component integrated into a roof covering.
BUILT-UP ROOF COVERING. Two or more layers of felt cemented together and surfaced with a cap sheet, mineral aggregate, smooth coating or similar surfacing material.
INTERLAYMENT. A layer of felt or nonbituminous saturated felt not less than 18 inches (457 mm) wide, shingled between each course of a wood-shake roof covering.
MECHANICAL EQUIPMENT SCREEN. A partially enclosed rooftop structure used to aesthetically conceal heating, ventilating and air conditioning (HVAC) electrical or mechanical equipment from view.
METAL ROOF PANEL. An interlocking metal sheet having a minimum installed weather exposure of 3 square feet (0.279 m2) per sheet.
METAL ROOF SHINGLE. An interlocking metal sheet having an installed weather exposure less than 3 square feet (0.279 m2) per sheet.
MODIFIED BITUMEN ROOF COVERING. One or more layers of polymer-modified asphalt sheets. The sheet materials shall be fully adhered or mechanically attached to the substrate or held in place with an approved ballast layer.
PENTHOUSE. An enclosed, unoccupied structure above the roof of a building, other than a tank, tower, spire, dome cupola or bulkhead.
POSITIVE ROOF DRAINAGE. The drainage condition in which consideration has been made for all loading deflections of the roof deck, and additional slope has been provided to ensure drainage of the roof within 48 hours of precipitation.
REROOFING. The process of recovering or replacing an existing roof covering. See "Roof recover" and "Roof replacement."
ROOF ASSEMBLY. A system designed to provide weather protection and resistance to design loads. The system consists of a roof covering and roof deck or a single component serving as both the roof covering and the roof deck. A roof assembly includes the roof deck, vapor retarder, substrate or thermal barrier, insulation, vapor retarder and roof covering.
The definition of "Roof assembly" is limited in application to the provisions of Chapter 15.
ROOF COVERING. The covering applied to the roof deck for weather resistance, fire classification or appearance.
ROOF COVERING SYSTEM. See "Roof assembly."
ROOF DECK. The flat or sloped surface not including its supporting members or vertical supports.
ROOF RECOVER. The process of installing an additional roof covering over a prepared existing roof covering without removing the existing roof covering.
ROOF REPAIR. Reconstruction or renewal of any part of an existing roof for the purposes of its maintenance.
ROOF REPLACEMENT. The process of removing the existing roof covering, repairing any damaged substrate and installing a new roof covering.
ROOF SECTION. A separation or division of a roof area by existing joints, parapet walls, flashing (excluding valleys), difference of elevation (excluding hips and ridges), roof type or legal description; not including the roof area required for a proper tie-off with an existing system.
ROOF VENTILATION. The natural or mechanical process of supplying conditioned or unconditioned air to, or removing such air from, attics, cathedral ceilings or other enclosed spaces over which a roof assembly is installed.
ROOFTOP STRUCTURE. An enclosed structure on or above the roof of any part of a building.
SCUPPER. An opening in a wall or parapet that allows water to drain from a roof.
SINGLE-PLY MEMBRANE. A roofing membrane that is field applied using one layer of membrane material (either homogeneous or composite) rather than multiple layers.
UNDERLAYMENT. One or more layers of felt, sheathing paper, nonbituminous saturated felt or other approved material over which a steep-slope roof covering is applied.
(Mod R5258 / AS)
Section 1503 – Weather Protection
Change Section 1503.2 to read as shown:
1503.2 Flashing. Flashing shall be installed in such a manner so as to prevent moisture entering the wall and roof through joints in copings, through moisture-permeable materials and at intersections with parapet walls and other penetrations through the roof plane.
1503.2.1 Locations. Flashing shall be installed at wall and roof intersections, at gutters, wherever there is a change in roof slope or direction and around roof openings. Where flashing is of metal, the metal shall be corrosion resistant with a thickness not less than 0.019 inch (0.483 mm) (No. 26 galvanized sheet) provided in Table 1503.2.
Exception: This requirement does not apply to hip and ridge junctions.
TABLE 1503.2
METAL FLASHING MATERIAL
|MATERIAL |MINIMUM |GAGE |WEIGHT (LBS |
| |THICKNESS | |PER SQ FT) |
| |(INCHES) | | |
|Copper | | |1 (16 oz) |
|Aluminum |0.024 | | |
|Stainless Steel | |28 | |
|Galvanized Steel |0.0179 |26 (zinc | |
| | |coated G90) | |
|Aluminum Zinc |0.0179 |26 (AZ50 | |
|Coated Steel | |Alum Zinc) | |
|Zinc Alloy |0.027 | | |
|Lead | | |2.5 (40 oz) |
|Painted Terne | | |1.25 (20 oz) |
(Mod R5340 / AS) (Mod R5341 / AS)
Section 1503 – Weather Protection
Change Section 1503.4 to read as shown:
1503.4 Roof drainage. Unless roofs are sloped to drain over roof edges, D design and installation of roof drainage systems shall comply with Section 1503 of this code and Sections 1106 and 1108, as applicable, of and the Florida Building Code, Plumbing, Chapter 11 International Plumbing Code.
(Mod R5345 / AS)
Section 1503 – Weather Protection
Change Section 1503.4.1 to read as shown:
1503.4.1 Secondary (emergency overflow) drains or scuppers. Where roof drains are required, secondary (emergency overflow) roof drains or scuppers shall be provided where the roof perimeter construction extends above the roof in such a manner that water will be entrapped if the primary drains allow buildup for any reason. The installation and sizing of secondary emergency overflow drains, leaders and conductors shall comply with Sections 1106 and 1108 1107, as applicable, of the International Plumbing Code Florida Building Code, Plumbing, Chapter 11 .
(Mod R5342 / AS)
Section 1503 – Weather Protection
Change Section 1503.4.2 to read as shown:
1503.4.2 Scuppers. Where required for roof drainage, a scupper shall be placed level with the roof surface in a wall or parapet. The scupper shall be located as determined by the slope and the contributing area of the roof. The exterior facing or lining of a scupper, if metal, shall be the same as flashing material required by Sections 1503 through 1510 for the particular type of covering specified for the building. For other type materials, follow manufacturer's specifications. When scuppers are used for secondary (emergency overflow) roof drainage, the quantity, size, location and inlet elevation of the scuppers shall be sized to prevent the depth of ponding water from exceeding that for which the roof was designed as determined by Section 1611.1. Scuppers shall not have an opening dimension of less than 4 inches (102 mm). The flow through the primary system shall not be considered when locating and sizing scuppers.
(Mod R5344 / AS)
Section 1503 – Weather Protection
Add Section 1503.4.2.1 to read as shown:
1503.4.2.1 Overflow scuppers. When other means of drainage of overflow water is not provided, overflow scuppers shall be placed in walls or parapets not less than 2 inches (51 mm) nor more than 4 inches (102 mm) above the finished roof covering and shall be located as close as practical to required vertical leaders or downspouts or wall and parapet scuppers. An overflow scupper shall be sized in accordance with the Florida Building Code, Plumbing.
(Mod R5343 / AS)
Section 1503 – Weather Protection
Change Section 1503.5 to read as shown:
1503.5 Roof ventilation. Attic ventilation Intake and exhaust vents shall be provided in accordance with Section 1203.2 and the manufacturer's installation instructions.
(Mod R5346 / AS)
Section 1503 – Weather Protection
Change Section 1503.7 to read as shown:
1503.7 Protection against decay and termites. Condensate lines and roof downspouts shall discharge at least 1 foot (305 mm) away from the structure sidewall, whether by underground piping, tail extensions, or splash blocks. Gutters with downspouts are required on all buildings with eaves of less than 6 inches (152 mm) horizontal projection except for gable end rakes or on a roof above another roof.
Section 1504 – Performance Requirements
Change Section 1504.1.1 to read as shown:
1504.1.1 Wind resistance of asphalt shingles. Asphalt shingles shall comply be designed for wind speeds in accordance with Section 1507.2.7.
(Mod R5348 / AS)
Section 1504 – Performance Requirements
Change Section 1504.3.2 to read as shown:
Section 1504.3.2 Metal panel roof systems. Change to read as shown:
1504.3.2 Metal panel roof systems. Metal panel roof systems through fastened or standing seam shall be tested in accordance with UL 580 or ASTM E 1592 or TAS 125.
(No change to remainder of text).
(Mod R5349 / AS)
Section 1504 – Performance Requirements
Change Section 1504.5 to read as shown:
1504.5 Edge securement for low-slope roofs. Low-slope built-up, modified bitumen and single-ply roof system metal edge securement, except gutters, shall be designed and installed for wind loads in accordance with Chapter 16 and tested for resistance in accordance with Test Methods RE-1, RE-2 and RE-3 of ANSI/SPRI ES-1, or RAS 111 except Vult wind speed shall be determined from Figure 1609A, 1609B, or 1609C as applicable.
(Mod R5350 / AS)
Section 1504 – Performance Requirements
Change Section 1504.6 to read as shown:
1504.6 Physical properties. Roof coverings installed on low-slope roofs (roof slope < 2:12) in accordance with Section 1507 shall demonstrate physical integrity over the working life of the roof based upon 2,000 hours of exposure to accelerated weathering tests conducted in accordance with ASTM G 152, ASTM G 153, ASTM G 155 or ASTM G 154. Those roof coverings that are subject to cyclical flexural response due to wind loads shall not demonstrate any significant loss of tensile strength for unreinforced membranes or breaking strength for reinforced membranes when tested as herein required.
(Mod R5351 / AS)
Section 1504 – Performance Requirements
Change Section 1504.7 to read as shown:
1504.7 Impact resistance. Roof coverings installed on low-slope roofs (roof slope < 2:12) in accordance with Section 1507 shall resist impact damage based on the results of tests conducted in accordance with ASTM D 3746, ASTM D 4272, CGSB 37-GP-52M or the "Resistance to Foot Traffic Test" in Section 5.5 of FM 4470. All structural metal roofing systems having a thickness equal to or greater than 22 gage and all non-structural metal roof systems having a thickness equal to or greater than 26 gage shall be exempt from the tests listed above.
(Mod R5352 / AS)
Section 1504 – Performance Requirements
Change Section 1504.8 to read as shown:
1504.8 Aggregate. Aggregate used as surfacing for roof coverings and aggregate, gravel or stone used as ballast shall not be used on the roof of a building located in a hurricane-prone region as defined in Section 202, or on any other building with a mean roof height exceeding that permitted by Table 1504.8 based on the exposure category and basic wind speed at the site shall be permitted as roof surfacing when installed on slopes of 3:12 or less, not less than 400 pound (182 kg) of roofing gravel or 300 pounds (145 kg) of slag per square shall be applied. A minimum of 50 percent of the total aggregate shall be embedded in the flood coat of bitumen or installed in accordance with its product approval. Aggregate shall be dry and free from dirt and shall be in compliance with the sizing requirements set forth in ASTM D 1863. A building official may request a test to confirm compliance with these requirements.
TABLE 1504.8
MAXIMUM ALLOWABLE MEAN ROOF HEIGHT PERMITTED FOR BUILDINGS WITH AGGREGATE ON THE ROOF IN AREAS OUTSIDE A HURRICANE-PRONE REGION
Reserved.
|NOMINAL DESIGN WIND |MAXIMUM MEAN ROOF HEIGHT (ft)a, c |
|SPEED, Vasd (mph)b, d | |
| |Exposure category |
| |B |C |D |
|85 |170 |60 |30 |
|90 |110 |35 |15 |
|95 |75 |20 |NP |
|100 |55 |15 |NP |
|105 |40 |NP |NP |
|110 |30 |NP |NP |
|115 |20 |NP |NP |
|120 |15 |NP |NP |
|Greater than 120 |NP |NP |NP |
| For SI: 1 foot = 304.8 mm; 1 mile per hour = 0.447 m/s. |
|a. Mean roof height as defined in ASCE 7. |
|b. For intermediate values of Vasd, the height associated with the next higher value of Vasd shall be used, or direct interpolation is |
|permitted. |
|c. NP = gravel and stone not permitted for any roof height. |
d. Vasd shall be determined in accordance with Section 1609.3.1.
(Mod R5353 / AS)
Section 1504 – Performance Requirements
Add Section 1504.9 to read as shown:
1504.9 Margin of Safety. A margin of safety of 2:1 shall be applied to all wind uplift resistance test results except when a margin of safety is specified in the test standard.
Exception: Asphalt shingles testing resulting in a miles per hour rating as required in section 1507.2.7.
(Mod R5686 / AS)
Section 1505 – Fire Classification
Change Section 1505.7 to read as shown:
Section 1505.7 Special purpose roofs. Change to read as shown:
1505.7 Special purpose roofs. Reserved. Special purpose wood shingle or wood shake roofing shall conform with the grading and application requirements of Section 1507.8 or 1507.9. In addition, an underlayment of 5/8-inch (15.9 mm) Type X water-resistant gypsum backing board or gypsum sheathing shall be placed under minimum nominal 1/2-inch-thick (12.7 mm) wood structural panel solid sheathing or 1-inch (25 mm) nominal spaced sheathing.
(Mod R5356 / AS)
Section 1506 – Materials
Add Section 1506.5 to read as shown:
1506.5 Nails. Nails shall be corrosion resistant nails conforming to ASTM F 1667. The corrosion resistance shall meet ASTM A 641, Class 1 or an equal corrosion resistance by coating, electro galvanization, mechanical galvanization, hot dipped galvanization, stainless steel, nonferrous metal and alloys or other suitable corrosion resistant material.
(Mod R5357 / AS)
Section 1506 – Materials
Add Section 1506.6 to read as shown:
1506.6 Screws. Wood screws conform to ANSI/ASME B 18.6.1. Screws shall be corrosion resistant by coating, galvanization, stainless steel, nonferrous metal or other suitable corrosion resistant material. The corrosion resistance shall be demonstrated through one of the following methods:
1. Corrosion resistance equivalent to ASTM A 641, Class 1;
2. Corrosion resistance in accordance with TAS114, Appendix E; or
3. Corrosion resistant coating exhibiting not more than 5 percent red rust after 1000 hours exposure in accordance with ASTM B 117.
(Mod R5358 / AS)
Section 1506 – Materials
Add Section 1506.7 to read as shown:
1506.7 Clips. Clips shall be corrosion resistant clips. The corrosion resistance shall meet 0.90 ounce per square foot (0.458 kg/m2) measured according to ASTM A 90/A 90M, TAS 114 Appendix E or an equal corrosion resistance coating, electro galvanization, mechanical galvanization, hot dipped galvanization, stainless steel, nonferrous metals and alloys or other suitable corrosion resistant material. Stainless steel clips shall conform to ASTM A167, Type 304.
(Mod R5359 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.3 to read as shown:
Section 1507.2.3 Underlayment. Change section to read as shown:
1507.2.3 Underlayment. Unless otherwise noted, required underlayment shall conform to ASTM D 226, Type I or Type II, or ASTM D 4869 Type I II or Type IV or ASTM D 6757.
(Mod R5360 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.5 to read as shown:
1507.2.5 Asphalt shingles. Asphalt shingles shall have self-seal strips or be interlocking and comply with ASTM D 225 or ASTM D 3462. Shingles shall also comply with Table 1507.2.7.1. Asphalt shingle packaging shall bear labeling indicating compliance with one of the required classifications as shown in Table 1507.2.7.1.
(Mod R5361 / AS)
Section 1507 – Requirements for Roof Coverings
Add Section 1507.2.6.1 to read as shown:
1507.2.6.1 The nail component of plastic cap nails shall meet the corrosion resistance requirements of Section 1506.5.
(Mod R5362 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.7 to read as shown:
1507.2.7 Attachment. Asphalt shingles shall have the minimum number of fasteners required by the manufacturer, but and Section 1504.1. Asphalt shingles shall be secured to the roof with not less than four fasteners per strip shingle or two fasteners per individual strip shingle or two fasteners per individual shingle. Where the roof slope exceeds 21 units vertical in 12 units horizontal (21:12), asphalt shingles shall be installed as required by in accordance with the manufacturer's printed installation instructions for steep-slope roof applications.
(Mod R5364 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.7.1 to read as shown:
1507.2.7.1 Wind Resistance of Asphalt Shingles. Asphalt shingles shall be tested classified in accordance with ASTM D 3161, TAS 107 or ASTM D 7158. Asphalt shingles shall meet the classification requirements of Table 1507.2.7.1(1) for the appropriate maximum basic wind speed. Shingles classified as ASTM D 3161 Class D or ASTM D 7158 Class G are acceptable for use in the 100-mph wind zone. Shingles classified as ASTM D 3161 Class F, TAS107 or ASTM D 7158 Class H are acceptable for use in all wind zones. Asphalt shingle packaging wrappers shall bear a label to indicate compliance with ASTM D 7158 and the one of the required classifications as shown in Table 1507.2.7.1(1).
Exception: Asphalt shingles not included in the scope of ASTM D 7158 shall be tested and labeled to indicate compliance with ASTM D 3161 and the required classification in Table 1507.2.7.1(2).
TABLE 1507.2.7.1(1)
CLASSIFICATION OF ASPHALT ROOF SHINGLES PER ASTM D 7158a
|NOMINAL DESIGN WIND SPEED, Vasdb (mph) |CLASSIFICATION REQUIREMENT |
|85 |D, G or H |
|90 |D, G or H |
|100 |G or H |
|110 |G or H |
|120 |G or H |
|130 |H |
|140 |H |
|150 |H |
|For SI: 1 foot = 304.8 mm; 1 mph = 0.447 m/s. |
|a. The standard calculations contained in ASTM D 7158 assume exposure category B or C and building height of 60 feet or less. Additional |
|calculations are required for conditions outside of these assumptions. |
|b. Vasd shall be determined in accordance with Section 1609.3.1. |
|MAXIMUM BASIC WIND |Vasd |ASTM D 7158 |ASTM D 3161 |
|SPEED FROM FIGURE | | | |
|1609A, B, C or ASCE-7 | | | |
|110 |85 |D, G or H |A, D or F |
|116 |90 |D, G or H |A, D or F |
|129 |100 |G or H |A, D or F |
|142 |110 |G or H |F |
|155 |120 |G or H |F |
|168 |130 |H |F |
|181 |140 |H |F |
|194 |150 |H |F |
TABLE 1507.2.7.1(2)
CLASSIFICATION OF ASPHALT SHINGLES PER ASTM D 3161
Reserved.
|NOMINAL DESIGN WIND SPEED, |CLASSIFICATION REQUIREMENT |
|Vasda (mph) | |
|85 |A, D or F |
|90 |A, D or F |
|100 |A, D or F |
|110 |F |
|120 |F |
|130 |F |
|140 |F |
|150 |F |
|For SI: 1 mph = 0.447 m/s. |
|a. Vasd shall be determined in accordance with Section 1609.3.1. |
| |
(Mod R5363- R2 / AM)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.8 to read as shown:
1507.2.8 Underlayment application. Underlayment shall be installed using one of the following methods: For roof slopes from two units vertical in 12 units horizontal (17-percent slope) and up to four units vertical in 12 units horizontal (33-percent slope), underlayment shall be two layers applied in the following manner. Apply a minimum 19-inch-wide (483 mm) strip of underlayment felt parallel with and starting at the eaves, fastened sufficiently to hold in place. Starting at the eave, apply 36-inch-wide (914 mm) sheets of underlayment overlapping successive sheets 19 inches (483 mm), by fastened sufficiently to hold in place. Distortions in the underlayment shall not interfere with the ability of the shingles to seal. For roof slopes of four units vertical in 12 units horizontal (33-percent slope) or greater, underlayment shall be one layer applied in the following manner. Underlayment shall be applied shingle fashion, parallel to and starting from the eave and lapped 2 inches (51 mm), fastened sufficiently to hold in place. Distortions in the underlayment shall not interfere with the ability of the shingles to seal.
1. For roof slopes from two units vertical in 12 units horizontal (17-percent slope), and less than four units vertical in 12 units horizontal (33-percent slope). Underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or Type IV or ASTM D 6757 and shall be two layers applied in the following manner. Apply a 19-inch (483 mm) strip of underlayment felt parallel to and starting at the eaves, fastened sufficiently to hold in place. Starting at the eave, apply 36-inch-wide (914 mm) sheets of underlayment, overlapping successive sheets 19 inches (483 mm), and fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with one row in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened in accordance with this section and the manufacturer’s recommendations.
2. For roof slopes of four units vertical in 12 units horizontal (33-percent slope) or greater. Underlayment shall comply with ASTM D 226, Type II or ASTM D 4869, Type IV or ASTM D 6757 and shall be one layer applied in the following manner. Underlayment shall be applied shingle fashion, parallel to and starting from the eave and lapped 2 inches (51 mm), fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with two staggered rows in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened in accordance with this section and the manufacturer’s recommendations End laps shall be offset by 6 feet (1829 mm).
3. As an alternative, the entire roof deck shall be covered with an approved self-adhering polymer modified bitumen sheet meeting ASTM D 1970 or an approved self-adhering synthetic underlayment installed in accordance with the manufacturer’s installation instructions.
(Mod R5562 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.8.1 to read as shown:
1507.2.8.1 High wind attachment. Reserved
Underlayment applied in areas subject to high winds [Vasd greater than 110 mph (49 m/s) as determined in accordance with Section 1609.3.1] shall be applied with corrosion-resistant fasteners in accordance with the manufacturer's instructions. Fasteners are to be applied along the overlap at a maximum spacing of 36 inches (914 mm) on center.
Underlayment installed where Vasd, in accordance with Section 1609.3.1, equals or exceeds 120 mph (54 m/s) shall comply with ASTM D 226 Type II, ASTM D 4869 Type IV, or ASTM D 6757. The underlayment shall be attached in a grid pattern of 12 inches (305 mm) between side laps with a 6-inch (152 mm) spacing at the side laps. Underlayment shall be applied in accordance with Section 1507.2.8 except all laps shall be a minimum of 4 inches (102 mm). Underlayment shall be attached using metal or plastic cap nails with a head diameter of not less than 1 inch (25 mm) with a thickness of at least 32-gauge [0.0134 inch (0.34 mm)] sheet metal. The cap nail shank shall be a minimum of 12 gauge [0.105 inch (2.67 mm)] with a length to penetrate through the roof sheathing or a minimum of 3/4 inch (19.1 mm) into the roof sheathing.
Exception: As an alternative, adhered underlayment complying with ASTM D 1970 shall be permitted.
(Mod R5365 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.8.2 to read as shown:
1507.2.8.2 Ice barrier. Reserved.
In areas where there has been a history of ice forming along the eaves causing a backup of water, an ice barrier that consists of at least two layers of underlayment cemented together or of a self-adhering polymer modified bitumen sheet shall be used in lieu of normal underlayment and extend from the lowest edges of all roof surfaces to a point at least 24 inches (610 mm) inside the exterior wall line of the building.
Exception: Detached accessory structures that contain no conditioned floor area.
(Mod R5367 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.9.1 to read as shown:
1507.2.9.1 Base and cap counter flashing. Base and cap counter flashing shall be installed in accordance with the manufacturer's instructions. Base flashing shall be of either corrosion-resistant metal of minimum nominal 0.019-inch (0.483 mm) thickness or mineral-surfaced roll roofing weighing a minimum of 77 pounds per 100 square feet (3.76 kg/m2). Cap flashing shall be corrosion-resistant metal of minimum nominal 0.019-inch (0.483 mm) thickness. as follows:
1. In accordance with manufacturer's installation instructions, or
2. A continuous metal minimum 4? × 4? "L" flashing shall be set in approved flashing cement and set flush to base of wall and over the underlayment. Both horizontal and vertical metal flanges shall be fastened 6 inches (152 mm) on center with approved fasteners. All laps shall be a minimum of 4 inches (102 mm) fully sealed in approved flashing cement. Flashing shall start at the lower portion of roof to insure water-shedding capabilities of all metal laps. The entire edge of the horizontal flange shall be sealed covering all nail penetrations with approved flashing cement and membrane. Shingles will overlap the horizontal flange and shall be set in approved flashing cement.
Base flashing shall be of either corrosion resistant metal with a minimum thickness provided in Table 1503.2 or mineral surface roll roofing weighing a minimum of 77 pounds per 100 square feet (3.76 kg/m2). Counter flashing shall be corrosion resistant metal with a minimum thickness provided in Table 1503.2.
(Mod R5370 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.9.2 to read as shown:
1507.2.9.2 Valleys. Valley linings shall be installed in accordance with the manufacturer's instructions before applying shingles. Valley linings of the following types shall be permitted:
1. For open valleys (valley lining exposed) lined with metal, the valley lining shall be at least 24 16 inches (610 406 mm) wide and of any of the corrosion-resistant metals in Table 15073.2.9. 2.
2. For open valleys, valley lining of two plies of mineral-surfaced roll roofing complying with ASTM D 3909 or ASTM D 6380 Class M shall be permitted. The bottom layer shall be 18 inches (457 mm) and the top layer a minimum of 36 inches (914 mm) wide.
3. For closed valleys (valleys covered with shingles), valley lining of one ply of smooth roll roofing complying with ASTM D 6380 Class S , and at least 36 inches (914 mm) wide or types as described in Item 1 or 2 above shall be permitted. Self-adhering polymer modified bitumen underlayment complying with ASTM D 1970 shall be permitted in lieu of the lining material.
TABLE 1507.2.9.2
VALLEY LINING MATERIAL
Reserved.
|MATERIAL |MINIMUM THICKNESS |GAGE |WEIGHT |
|Aluminum |0.024 in. |— |— |
|Cold-rolled copper |0.0216 in. |— |ASTM B 370, 16 oz. per square ft. |
|Copper |— |— |16 oz |
|Galvanized steel |0.0179 in. |26 (zinc-coated G90) |— |
|High-yield copper |0.0162 in. |— |ASTM B 370, 12 oz. per square ft. |
|Lead |— |— |2.5 pounds |
|Lead-coated copper |0.0216 in. |— |ASTM B 101, 16 oz. per square ft. |
|Lead-coated high-yield |0.0162 in. |— |ASTM B 101, 12 oz. per square ft. |
|copper | | | |
|Painted terne |— |— |20 pounds |
|Stainless steel |— |28 |— |
|Zinc alloy |0.027 in. |— |— |
| For SI: 1 inch = 25.4 mm, 1 pound = 0.454 kg, 1 ounce = 28.35 g, 1 square foot = 0.093 m2. |
(Mod R5371 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.2.9.3 to read as shown:
1507.2.9.3 Drip edge. Provide drip edge at eaves and gables of shingle roofs. Overlap to be a minimum of 2 3 inches (51 76 mm). Eave drip edges shall extend ¼ 1/2 inch (6.4 13 mm) below sheathing and extend back on the roof a minimum of 2 inches (51 mm). Drip edge at eaves shall be permitted to be installed either over or under the underlayment. If installed over the underlayment, there shall be a minimum 4 inches (51 mm) width of roof cement installed over the drip edge flange. Drip edge shall be mechanically fastened a maximum of 12 inches (305 mm) on center. Where the Vasd as determined in accordance with Section 1609.3.1 is 110 mph (177 km/h) or greater or the mean roof height exceeds 33 feet (10 058 mm), drip edges shall be mechanically fastened a maximum of 4 inches (102 mm) on center.
(Mod R5372 / AS)
|Section 1507 – Requirements for Roof Coverings |
|Change Section 1507.3 to read as shown: |
|Section 1507.3 Clay and concrete tile. Change to read as shown: |
|1507.3 Clay and concrete tile. The installation of clay and concrete tile shall comply with the provisions of this section. |
|1507.3.1 Deck requirements. Concrete and clay tile shall be installed only over solid sheathing or except where the roof covering is |
|specifically designed and tested in accordance with Section 1609.5.2 to be applied over spaced structural spaced sheathing boards. (Mod |
|R5373 / AS) |
|1507.3.2 Deck slope. |
|Clay and concrete roof tile shall be installed on roof slopes of 21/2 units vertical in 12 units horizontal (21-percent slope) or greater. |
|For roof slopes from 21/2 units vertical in 12 units horizontal (21-percent slope) to four units vertical in 12 units horizontal (33-percent|
|slope), double underlayment application is required in accordance with Section 1507.3.3. in accordance with the recommendations of FRSA/TRI |
|Florida High Wind Concrete and Clay Roof Tile Installation Manual, Fifth Edition where the Vasd as determined in accordance with Section |
|1609.3.1 or the recommendations of RAS 118, 119 or 120. |
| 1507.3.3 Underlayment. |
|Unless otherwise noted, required underlayment shall conform to: ASTM D 226, Type II; ASTM D 2626, ASTM D 1970 or ASTM D 6380, Class M |
|mineral-surfaced roll roofing. Underlayment shall be applied according to the tile manufacturer's installation instructions or the |
|recommendations of the FRSA/TRI Florida High Wind Concrete and Clay Roof Tile Installation Manual, Fifth Edition where the basic wind speed,|
|Vasd, is determined in accordance with Section 1609.3.1 or the recommendations of RAS 118, 119 or 120. |
|1507.3.3.1 Low-slope roofs Slope and underlayment requirements. Refer to FRSA/TRI Florida High Wind Concrete and Clay Roof Tile Installation|
|Manual, Fifth Edition where the basic wind speed, Vasd, is determined in accordance with Section 1609.3.1 for underlayment and slope |
|requirements for specific roof tile systems or the recommendations of RAS 118, 119 or 120. |
|For roof slopes from 21/2 units vertical in 12 units horizontal (21-percent slope), up to four units vertical in 12 units horizontal |
|(33-percent slope), underlayment shall be a minimum of two layers applied as follows: |
|1. Starting at the eave, a 19-inch (483 mm) strip of underlayment shall be applied parallel with the eave and fastened sufficiently in |
|place. |
|2. Starting at the eave, 36-inch-wide (914 mm) strips of underlayment felt shall be applied overlapping successive sheets 19 inches (483 mm)|
|and fastened sufficiently in place. |
|1507.3.3.2 High-slope roofs. Reserved. |
|For roof slopes of four units vertical in 12 units horizontal (33-percent slope) or greater, underlayment shall be a minimum of one layer of|
|underlayment felt applied shingle fashion, parallel to, and starting from the eaves and lapped 2 inches (51 mm), fastened only as necessary |
|to hold in place. |
|1507.3.3.3 High wind attachment. Reserved. |
|Underlayment applied in areas subject to high wind [Vasd greater than 110 mph (49 m/s) as determined in accordance with Section 1609.3.1] |
|shall be applied with corrosion-resistant fasteners in accordance with the manufacturer's installation instructions. Fasteners are to be |
|applied along the overlap not farther apart than 36 inches (914 mm) on center. |
| |
|Underlayment installed where Vasd, in accordance with Section 1609.3.1, equals or exceeds 120 mph (54 m/s) shall be attached in a grid |
|pattern of 12 inches (305 mm) between side laps with a 6-inch (152 mm) spacing at the side laps. Underlayment shall be applied in accordance|
|with Sections 1507.3.3.1 and 1507.3.3.2 except all laps shall be a minimum of 4 inches (102 mm). Underlayment shall be attached using metal |
|or plastic cap nails with a head diameter of not less than 1 inch (25 mm) with a thickness of at least 32-gauge [0.0134 inch (0.34 mm)] |
|sheet metal. The cap nail shank shall be a minimum of 12 gauge [0.105 inch (2.67 mm)] with a length to penetrate through the roof sheathing |
|or a minimum of 3/4 inch (19.1 mm) into the roof sheathing. |
|Exception: As an alternative, adhered underlayment complying with ASTM D 1970 shall be permitted. |
|1507.3.4 Clay tile. Clay roof tile shall comply with ASTM C 1167. |
|1507.3.5 Concrete tile. Concrete roof tile shall comply with ASTM C 1492. |
|1507.3.6 Fasteners. Tile fasteners shall be corrosion resistant and not less than 11 gage, 5/16-inch (8.0 mm) head, and of sufficient length|
|to penetrate the deck a minimum of ¾ 0.75 inch (19.1 mm) or through the thickness of the deck, whichever is less or in accordance with the |
|FRSA/TRI Florida High Wind Concrete and Clay Roof Tile Installation Manual, Fifth Edition where the basic wind speed, Vasd, is determined in|
|accordance with Section 1609.3.1 or in accordance with RAS 118, 119 or 120. Attaching wire for clay or concrete tile shall not be smaller |
|than 0.083 inch (2.1 mm). Perimeter fastening areas include three tile courses but not less than 36 inches (914 mm) from either side of hips|
|or ridges and edges of eaves and gable rakes. |
|1507.3.7 Attachment. Clay and concrete roof tiles shall be fastened in accordance with Table 1507.3.7Section 1609 or in accordance with |
|FRSA/TRI Florida High Wind Concrete and Clay Roof Tile Installation Manual, Fifth Edition where the basic wind speed, Vasd, is determined in|
|accordance with Section 1609.3.1. . |
| |
|TABLE 1507.3.7 |
|CLAY AND CONCRETE TILE ATTACHMENTa, b, c |
|Reserved. |
| |
|GENERAL - CLAY OR CONCRETE ROOF TILE |
| |
|Maximum Nominal Design Wind Speed, Vasdf (mph) |
|Mean roof height |
|(feet) |
|Roof slope < 3:12 |
|Roof slope 3:12 and over |
| |
|85 |
|0-60 |
|One fastener per tile. Flat tile without vertical laps, two fasteners per tile. |
|Two fasteners per tile. Only one fastener on slopes of 7:12 and less for tiles with installed weight exceeding 7.5 lbs./sq. ft. having a |
|width no greater than 16 inches. |
| |
|100 |
|0-40 |
| |
| |
| |
|100 |
|>40-60 |
|The head of all tiles shall be nailed. The nose of all eave tiles shall be fastened with approved clips. All rake tiles shall be nailed with|
|two nails. The nose of all ridge, hip and rake tiles shall be set in a bead of roofer's mastic. |
| |
|110 |
|0-60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|120 |
|0-60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|130 |
|0-60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|All |
|>60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|INTERLOCKING CLAY OR CONCRETE ROOF TILE WITH PROJECTING ANCHOR LUGSd, e |
|(Installations on spaced/solid sheathing with battens or spaced sheathing) |
| |
|Maximum Nominal Design Wind Speed, Vasdf (mph) |
|Mean roof height |
|(feet) |
|Roof slope < 5:12 |
|Roof slope 5:12 < 12:12 |
|Roof slope |
|12:12 and over |
| |
|85 |
|0-60 |
|Fasteners are not required. Tiles with installed weight less than 9 lbs./sq. ft. require a minimum of one fastener per tile. |
|One fastener per tile every other row. All perimeter tiles require one fastener. Tiles with installed weight less than 9 lbs./sq. ft. |
|require a minimum of one fastener per tile. |
|One fastener required for every tile. Tiles with installed weight less than 9 lbs./sq. ft. require a minimum of one fastener per tile. |
| |
|100 |
|0-40 |
| |
| |
| |
| |
|100 |
|>40-60 |
|The head of all tiles shall be nailed. The nose of all eave tiles shall be fastened with approved clips. All rake tiles shall be nailed with|
|two nails The nose of all ridge, hip and rake tiles shall be set in a bead of roofer's mastic. |
| |
|110 |
|0-60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|120 |
|0-60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|130 |
|0-60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|All |
|>60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|INTERLOCKING CLAY OR CONCRETE ROOF TILE WITH PROJECTING ANCHOR LUGS |
|(Installations on solid sheathing without battens) |
| |
|Maximum Nominal Design Wind Speed, Vasdf (mph) |
|Mean roof height |
|(feet) |
|All roof slopes |
| |
|85 |
|0-60 |
|One fastener per tile. |
| |
|100 |
|0-40 |
|One fastener per tile. |
| |
|100 |
|> 40-60 |
|The head of all tiles shall be nailed. The nose of all eave tiles shall be fastened with approved clips. All rake tiles shall be nailed with|
|two nails The nose of all ridge, hip and rake tiles shall be set in a bead of roofer's mastic. |
| |
|110 |
|0-60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|120 |
|0-60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|130 |
|0-60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
|All |
|> 60 |
|The fastening system shall resist the wind forces in Section 1609.5.3. |
| |
| For SI: 1 inch =25.4 mm, 1 foot = 304.8 mm, 1 mile per hour = 0.447 m/s, 1 pound per square foot = 4.882 kg/m2. |
| |
|a. Minimum fastener size. Corrosion-resistant nails not less than No. 11 gage with 5/16-inch head. Fasteners shall be long enough to |
|penetrate into the sheathing 3/4 inch or through the thickness of the sheathing, whichever is less. Attaching wire for clay and concrete |
|tile shall not be smaller than 0.083 inch. |
| |
|b. Snow areas. A minimum of two fasteners per tile are required or battens and one fastener. |
| |
|c. Roof slopes greater than 24:12. The nose of all tiles shall be securely fastened. |
| |
|d. Horizontal battens. Battens shall be not less than 1 inch by 2 inch nominal. Provisions shall be made for drainage by a minimum of |
|1/8-inch riser at each nail or by 4-foot-long battens with at least a 1/2-inch separation between battens. Horizontal battens are required |
|for slopes over 7:12. |
| |
|e. Perimeter fastening areas include three tile courses but not less than 36 inches from either side of hips or ridges and edges of eaves |
|and gable rakes. |
| |
|f. Vasd shall be determined in accordance with Section 1609.3.1. |
| |
| |
|1507.3.8 Application. Tile shall be applied according to the manufacturer's installation instructions or recommendations of the FRSA/TRI |
| Florida High Wind Concrete and Clay Roof Tile Installation Manual, Fifth Edition where the basic wind speed, Vasd, is determined in |
|accordance with Section 1609.3.1 or the recommendation of RAS 118, 119 or 120., based on the following: |
|1. Climatic conditions. |
|2. Roof slope. |
|3. Underlayment system. |
|4. Type of tile being installed. |
|1507.3.9 Flashing. At the juncture of the roof vertical surfaces, flashing and counterflashing shall be provided in accordance with the |
|manufacturer's installation instructions , and where of metal, shall not be less than 0.019-inch (0.48 mm) (No. 26 galvanized sheet gage) |
|corrosion-resistant metal. The valley flashing shall extend at least 11 inches (279 mm) from the centerline each way and have a splash |
|diverter rib not less than 1 inch (25 mm) high at the flow line formed as part of the flashing. Sections of flashing shall have an end lap |
|of not less than 4 inches (102 mm). For roof slopes of three units vertical in 12 units horizontal (25-percent slope) and over, the valley |
|flashing shall have a 36-inch-wide (914 mm) underlayment of either one layer of Type I underlayment running the full length of the valley, |
|or a self-adhering polymer-modified bitumen sheet complying with ASTM D 1970, in addition to other required underlayment. In areas where the|
|average daily temperature in January is 25°F (-4°C) or less or where there is a possibility of ice forming along the eaves causing a backup |
|of water, the metal valley flashing underlayment shall be solid cemented to the roofing underlayment for slopes under seven units vertical |
|in 12 units horizontal (58-percent slope) or self-adhering polymer-modified bitumen sheet shall be installed or the recommendations of the |
|FRSA/TRI Florida High Wind Concrete and Clay Roof Tile Installation Manual, Fifth Edition where the basic wind speed, Vasd, is determined in|
|accordance with Section 1609.3.1 or the recommendation of RAS 118, 119 or 120. |
| |
|(Mod R5587-A1 / AM) |
Section 1507 – Requirements for Roof Coverings
Change Section 1507.4 to read as shown:
| |
|1507.4 Metal roof panels. The installation of metal roof panels shall comply with the provisions of this section. |
|1507.4.1 Deck requirements. Metal roof panel roof coverings shall be applied to a solid or closely fitted deck, except where the roof |
|covering is specifically designed to be applied to spaced supports. |
|1507.4.2 Deck slope. Minimum slopes for metal roof panels shall comply with the following: |
|1. The minimum slope for lapped, nonsoldered seam metal roofs without applied lap sealant shall be three units vertical in 12 units |
|horizontal (25-percent slope). |
|2. The minimum slope for lapped, nonsoldered seam metal roofs with applied lap sealant shall be one-half unit vertical in 12 units |
|horizontal (4-percent slope). Lap sealants shall be applied in accordance with the approved manufacturer's installation instructions. |
|3. The minimum slope for standing seam of roof systems shall be one-quarter unit vertical in 12 units horizontal (2-percent slope). |
| |
|1507.4.3 Material standards. Metal-sheet roof covering systems that incorporate supporting structural members shall be designed in |
|accordance with Chapter 22. Metal-sheet roof coverings installed over structural decking shall comply with Table 1507.4.3(1). The materials |
|used for metal-sheet roof coverings shall be naturally corrosion resistant or provided with corrosion resistance in accordance with the |
|standards and minimum thicknesses shown in Table 1507.4.3(2). |
| |
| |
|TABLE 1507.4.3(1) |
|METAL ROOF COVERINGS |
| |
|ROOF COVERING TYPE |
|STANDARD APPLICATION |
|RATE/THICKNESS |
| |
|Aluminum |
|ASTM B 209, 0.024 inch minimum thickness for roll-formed panels and 0.019 inch minimum thickness for press-formed |
|shingles. |
| |
|Aluminum-zinc alloy coated steel |
|ASTM A 792 AZ 50 |
| |
|Cold-rolled copper |
|ASTM B 370 minimum 16 oz./sq. ft. and 12 oz./sq. ft. high yield copper for metal-sheet roof covering systems: 12 oz./sq. ft. for preformed |
|metal shingle systems. |
| |
|Copper |
|16 oz./sq. ft. for metal-sheet roof-covering systems; 12 oz./sq. ft. for preformed metal shingle systems. |
| |
|Galvanized steel |
|ASTM A 653 G-90 zinc-coateda. |
| |
|Hard lead |
|2 lbs./sq. ft. |
| |
|Lead-coated copper |
|ASTM B 101 |
| |
|Prepainted steel |
|ASTM A 755 |
| |
|Soft lead |
|3 lbs./sq. ft. |
| |
|Stainless steel |
|ASTM A 240, 300 Series Alloys |
| |
|Steel |
|ASTM A 924 |
| |
|Terne and terne-coated stainless |
|Terne coating of 40 lbs. per double base box, field painted where applicable in accordance with manufacturer's installation instructions. |
| |
|Zinc |
|0.027 inch minimum thickness; 99.995% electrolytic high grade zinc with alloy additives of copper (0.08% - 0.20%), titanium (0.07% - 0.12%) |
|and aluminum (0.015%). |
| |
| |
| |
| ROOF COVERING TYPE |
|STANDARD |
|STANDARD APPLICATION |
|RATE/THICKNESS |
| |
|Aluminum |
|ASTM B 209 |
|0.024 inch minimum thickness for roll-formed panels and 0.019 inch minimum thickness for |
|press-formed shingles. |
| |
|Aluminum-zinc coated steel |
|ASTM A 792 |
|0.013 inch minimum thickness, |
|AZ 50 (coated minimum application rate) |
| |
|Cold-rolled copper |
|ASTM B 370 |
|Minimum 16 oz/sq. ft. and 12 oz./sq. ft. high yield copper for metal-sheet roof covering |
|systems: 12 oz/sq. ft. for preformed metal shingle systems. |
| |
|Copper |
|ASTM B 370 |
|16 oz./sq. ft. for metal-sheet roof-covering systems; 12 oz./sq. ft. for preformed metal shingle |
|systems. |
| |
|Galvanized steel |
|ASTM A 653 |
|0.013 inch minimum thickness, |
|G-90 zinc-coateda. |
| |
|Hard lead |
|- |
|2 lbs./sq. ft. |
| |
|Lead-coated copper |
|ASTM B 101 |
|- |
| |
|Prepainted steel |
|ASTM A 755 |
|- |
| |
|Soft lead |
|3 lbs./sq. ft. |
| |
| |
|Stainless steel |
|ASTM A 240 |
|300 Series Alloys |
| |
|Steel |
|ASTM A 924/ |
|ASTM A 924M |
|- |
| |
|Terne and |
|terne-coated stainless |
|- |
|Terne coating of 40 lbs. per double base box, field painted where applicable in accordance |
|with manufacturer's installation instructions. |
| |
|Zinc |
|- |
|0.027 inch minimum thickness; 99.995% electrolytic high grade zinc with alloy additives of |
|copper (0.08% - 0.20%), titanium (0.07% - 0.12%) and aluminum (0.015%). |
| |
| For SI: 1 ounce per square foot = 0.0026 kg/m2, |
| |
|1 pound per square foot = 4.882 kg/m2, |
| |
|1 inch = 25.4 mm, 1 pound = 0.454 kg. |
| |
|a. For Group U buildings, the minimum coating thickness for ASTM A 653 galvanized steel roofing shall be G-60. |
| |
| |
| |
| |
| |
| |
| |
| |
|TABLE 1507.4.3(2) |
|MINIMUM CORROSION RESISTANCE |
| |
|55% Aluminum-zinc alloy coated steel |
|ASTM A 792 AZ 50 |
| |
|5% Aluminum alloy-coated steel |
|ASTM A 875 GF60 |
| |
|Aluminum-coated steel |
|ASTM A 463 T2 65 |
| |
|Galvanized steel |
|ASTM A 653 G-90 |
| |
|Prepainted steel |
|ASTM A 755a |
| |
|a. Paint systems in accordance with ASTM A 755 shall be applied over steel products with corrosion-resistant coatings complying with ASTM A |
|792, ASTM A 875, ASTM A 463 or ASTM A 653. |
| |
| 1507.4.4 Attachment. Metal roof panels shall be secured to the supports in accordance with the approved manufacturer's fasteners. In the |
|absence of manufacturer recommendations, the following fasteners shall be used: |
|1. Galvanized fasteners shall be used for steel roofs. |
|2. Copper, brass, bronze, copper alloy or 300 series stainless-steel fasteners shall be used for copper roofs. |
|3. Aluminum-zinc coated fasteners are acceptable for aluminum-zinc coated roofs. |
|4. Stainless-steel fasteners are acceptable for all types of metal roofs. |
| |
|1507.4.5 Underlayment and high wind. Reserved. |
|Underlayment applied in areas subject to high winds [Vasd greater than 110 mph (49 m/s) as determined in accordance with Section 1609.3.1] |
|shall be applied with corrosion-resistant fasteners in accordance with the manufacturer's installation instructions. Fasteners are to be |
|applied along the overlap not farther apart than 36 inches (914 mm) on center. |
|Underlayment installed where Vasd, in accordance with Section 1609.3.1, equals or exceeds 120 mph (54 m/s) shall comply with ASTM D 226 Type|
|II, ASTM D 4869 Type IV, or ASTM D 1970. The underlayment shall be attached in a grid pattern of 12 inches (305 mm) between side laps with a|
|6-inch (152 mm) spacing at the side laps. Underlayment shall be applied in accordance with the manufacturer's installation instructions |
|except all laps shall be a minimum of 4 inches (102 mm). Underlayment shall be attached using metal or plastic cap nails with a head |
|diameter of not less than 1 inch (25 mm) with a thickness of at least 32-gauge [0.0134 inch (0.34 mm)] sheet metal. The cap nail shank shall|
|be a minimum of 12 gauge [0.105 inch (2.67 mm)] with a length to penetrate through the roof sheathing or a minimum of 3/4 inch (19.1 mm) |
|into the roof sheathing. |
|Exception: As an alternative, adhered underlayment complying with ASTM D 1970 shall be permitted. |
|1507.4.5.1 Underlayment. Underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or Type IV or ASTM D 1970 or |
|ASTM D 6757. |
| |
| 1507.4.5.2 Underlayment Application. Underlayment shall be installed using one of the following methods: |
|Two layer underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or Type IV or ASTM D 6757: Apply a 19-inch |
|(483 mm) strip of underlayment felt parallel to and starting at the eaves, fastened sufficiently to hold in place. Starting at the eave, |
|apply 36-inch-wide (914 mm) sheets of underlayment, overlapping successive sheets 19 inches (483 mm), and fastened with 1 inch (25 mm) round|
|plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with one row in the field of the sheet with a maximum |
|fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened|
|in accordance with this section and the manufacturer’s recommendations. |
| |
|One layer underlayment shall comply with ASTM D 226, Type II or ASTM D 4869, Type IV or ASTM D 6757: Underlayment shall be applied shingle |
|fashion, parallel to and starting from the eave and lapped 2 inches (51 mm), fastened with 1 inch (25 mm) round plastic cap, metal cap nails|
|or nails and tin-tabs attached to a nailable deck with two staggered rows in the field of the sheet with a maximum fastener spacing of 12 |
|in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened in accordance with |
|this section and the manufacturer’s recommendations End laps shall be offset by 6 feet (1829 mm). |
| |
|As an alternative, the entire roof deck shall be covered with an approved self-adhering polymer modified bitumen sheet meeting ASTM D 1970 |
|or an approved self-adhering synthetic underlayment installed in accordance with the manufacturer’s installation instructions. |
(Mod R5275-A1 / AM)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.5.2 to read as shown:
Section 1507.5.2. Add a section to read as shown:
1507.5.2.1 Underlayment shall be installed as per manufacturer's installation guidelines.
(Mod R5387 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.5.3 to read as shown:
Section 1507.5.3 Underlayment. Change to read as shown:
1507.5.3 Underlayment. Underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or Type IV or ASTM D 1970 or ASTM D 6757.
1507.5.3.1 Underlayment and high wind. Reserved.
Underlayment applied in areas subject to high winds [Vasd greater than 110 mph (49 m/s) as determined in accordance with Section 1609.3.1] shall be applied with corrosion-resistant fasteners in accordance with the manufacturer's installation instructions. Fasteners are to be applied along the overlap not farther apart than 36 inches (914 mm) on center.
Underlayment installed where Vasd, in accordance with Section 1609.3.1, equals or exceeds 120 mph (54 m/s) shall comply with ASTM D 226 Type II or ASTM D 4869 Type IV. The underlayment shall be attached in a grid pattern of 12 inches (305 mm) between side laps with a 6-inch spacing (152 mm) at the side laps. Underlayment shall be applied in accordance with the manufacturer's installation instructions except all laps shall be a minimum of 4 inches (102 mm). Underlayment shall be attached using metal or plastic cap nails with a head diameter of not less than 1 inch (25 mm) with a thickness of at least 32-gauge [0.0134 inch (0.34 mm)] sheet metal. The cap nail shank shall be a minimum of 12 gauge [0.105 inch (2.67 mm)] with a length to penetrate through the roof sheathing or a minimum of 3/4 inch (19.1 mm) into the roof sheathing.
Exception: As an alternative, adhered underlayment complying with ASTM D 1970 shall be permitted.
1507.5.3.2 Underlayment Application. Underlayment shall be installed using one of the following methods:
1. Two layer underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or Type IV or ASTM D 6757: Apply a 19-inch (483 mm) strip of underlayment felt parallel to and starting at the eaves, fastened sufficiently to hold in place. Starting at the eave, apply 36-inch-wide (914 mm) sheets of underlayment, overlapping successive sheets 19 inches (483 mm), and fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with one row in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened in accordance with this section and the manufacturer’s recommendations.
2. One layer underlayment shall comply with ASTM D 226, Type II or ASTM D 4869, Type IV or ASTM D 6757: Underlayment shall be applied shingle fashion, parallel to and starting from the eave and lapped 2 inches (51 mm), fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with two staggered rows in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened in accordance with this section and the manufacturer’s recommendations End laps shall be offset by 6 feet (1829 mm).
3. As an alternative, the entire roof deck shall be covered with an approved self-adhering polymer modified bitumen sheet meeting ASTM D 1970 or an approved self-adhering synthetic underlayment installed in accordance with the manufacturer’s installation instructions.
(Mod R5564 / AS)
| |
|Section 1507 – Requirements for Roof Coverings |
|Change Section 1507.5.4 to read as shown: |
|Section 1507.5.4 Ice barrier. Change to read as shown: |
|1507.5.4 Ice barrier. Reserved. In areas where there has been a history of ice forming along the eaves causing a backup of water, an ice |
|barrier that consists of at least two layers of underlayment cemented together or of a self-adhering polymer-modified bitumen sheet shall be|
|used in lieu of normal underlayment and extend from the lowest edges of all roof surfaces to a point at least 24 inches (610 mm) inside the |
|exterior wall line of the building. |
|Exception: Detached accessory structures that contain no conditioned floor area. |
|(Mod R5389 / AS) |
| |
|Section 1507 – Requirements for Roof Coverings |
|Change Section 1507.5.7 to read as shown: |
|1507.5.7 Flashing. Roof valley flashing shall be of corrosion-resistant metal of the same material as the roof covering or shall comply with|
|the standards in Table 1507.4.3(1). The valley flashing shall extend at least 8 inches (203 mm) from the centerline each way and shall have |
|a splash diverter rib not less than 3/4 0.75 inch (19.1 mm) high at the flow line formed as part of the flashing. Sections of flashing shall|
|have an end lap of not less than 4 inches (102 mm). In areas where the average daily temperature in January is 25°F (-4°C) or less or where |
|there is a possibility of ice forming along the eaves causing a backup of water, the metal valley flashing shall have a 36-inch-wide (914 |
|mm) underlayment directly under it consisting of either one layer of underlayment running the full length of the valley or a self-adhering |
|polymer-modified bitumen sheet complying with ASTM D 1970, in addition to underlayment required for metal roof shingles. The metal valley |
|flashing underlayment shall be solidly cemented to the roofing underlayment for roof slopes under seven units vertical in 12 units |
|horizontal (58-percent slope) or self-adhering polymer-modified bitumen sheet shall be installed. |
|(Mod R5390 / AS) |
Section 1507 – Requirements for Roof Coverings
Change Section 1507.6 to read as shown:
1507.6 Mineral-surfaced roll roofing. The installation of mineral-surfaced roll roofing shall comply with this section.
1507.6.1 Deck requirements. Mineral-surfaced roll roofing shall be fastened to solidly sheathed roofs.
1507.6.2 Deck slope. Mineral-surfaced roll roofing shall not be applied on roof slopes below one unit vertical in 12 units horizontal (8-percent slope).
1507.6.3 Underlayment. Underlayment shall comply with ASTM D 226, Type I or Type II, ASTM D 4869, Type II or Type IV or ASTM D 1970 or ASTM D 6757.
1507.6.3.1 Underlayment and high wind. Underlayment applied in areas subject to high winds [Vasd greater than 110 mph (49 m/s) as determined in accordance with Section 1609.3.1] shall be applied with corrosion-resistant fasteners in accordance with the manufacturer's installation instructions. Fasteners are to be applied along the overlap not farther apart than 36 inches (914 mm) on center.
Underlayment installed where Vasd, in accordance with Section 1609.3.1, equals or exceeds 120 mph (54 m/s) shall comply with ASTM D 226 Type II or ASTM D 4869 Type IV. The underlayment shall be attached in a grid pattern of 12 inches (305 mm) between side laps with a 6-inch spacing (152 mm) at the side laps. Underlayment shall be applied in accordance with the manufacturer's installation instructions except all laps shall be a minimum of 4 inches (102 mm). Underlayment shall be attached using metal or plastic cap nails with a head diameter of not less than 1 inch (25 mm) with a thickness of at least 32-gauge [0.0134 inch (0.34 mm)] sheet metal. The cap nail shank shall be a minimum of 12 gauge [0.105 inch (2.67 mm)] with a length to penetrate through the roof sheathing or a minimum of 3/4 inch (19.1 mm) into the roof sheathing.
Exception: As an alternative, adhered underlayment complying with ASTM D 1970 shall be permitted. Reserved.
1507.6.3.2 Underlayment Application. Underlayment shall be installed using one of the following methods:
1. Two layer underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or Type IV or ASTM D 6757: Apply a 19-inch (483 mm) strip of underlayment felt parallel to and starting at the eaves, fastened sufficiently to hold in place. Starting at the eave, apply 36-inch-wide (914 mm) sheets of underlayment, overlapping successive sheets 19 inches (483 mm), and fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with one row in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened in accordance with this section and the manufacturer’s recommendations.
2. One layer underlayment shall comply with ASTM D 226, Type II or ASTM D 4869, Type IV or ASTM D 6757: Underlayment shall be applied shingle fashion, parallel to and starting from the eave and lapped 2 inches (51 mm), fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with two staggered rows in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened in accordance with this section and the manufacturer’s recommendations End laps shall be offset by 6 feet (1829 mm).
3. As an alternative, the entire roof deck shall be covered with an approved self-adhering polymer modified bitumen sheet meeting ASTM D 1970 or an approved self-adhering synthetic underlayment installed in accordance with the manufacturer’s installation instructions.
1507.6.4 Ice barrier. In areas where there has been a history of ice forming along the eaves causing a backup of water, an ice barrier that consists of at least two layers of underlayment cemented together or of a self-adhering polymer-modified bitumen sheet shall be used in lieu of normal underlayment and extend from the lowest edges of all roof surfaces to a point at least 24 inches (610 mm) inside the exterior wall line of the building.
Exception: Detached accessory structures that contain no conditioned floor area. Reserved.
1507.6.5 Material standards. Mineral-surfaced roll roofing shall conform to ASTM D 3909 or ASTM D 6380 Class M or Class WS.
(Mod R5278 / AM)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.7 to read as shown:
1507.7 Slate shingles. The installation of slate shingles shall comply with the provisions of this section.
1507.7.1 Deck requirements. Slate shingles shall be fastened to solidly sheathed roofs.
1507.7.2 Deck slope. Slate shingles shall only be used on slopes of four units vertical in 12 units horizontal (4:12) or greater.
1507.7.3 Underlayment. Underlayment shall comply with ASTM D 226, Type I or Type II, ASTM D 4869, Type II or Type IV or ASTM D 1970 or ASTM D 6757.
1507.7.3.1 Underlayment and high wind. Reserved.
Underlayment applied in areas subject to high winds [Vasd greater than 110 mph (49 m/s) as determined in accordance with Section 1609.3.1] shall be applied with corrosion-resistant fasteners in accordance with the manufacturer's installation instructions. Fasteners are to be applied along the overlap not farther apart than 36 inches (914 mm) on center.
Underlayment installed where Vasd, in accordance with Section 1609.3.1, equals or exceeds 120 mph (54 m/s) shall comply with ASTM D 226 Type II or ASTM D 4869 Type IV. The underlayment shall be attached in a grid pattern of 12 inches (305 mm) between side laps with a 6-inch spacing (152 mm) at the side laps. Underlayment shall be applied in accordance with the manufacturer's installation instructions except all laps shall be a minimum of 4 inches (102 mm). Underlayment shall be attached using metal or plastic cap nails with a head diameter of not less than 1 inch (25 mm) with a thickness of at least 32-gauge [0.0134 inch (0.34 mm)] sheet metal. The cap nail shank shall be a minimum of 12 gauge [0.105 inch (2.67 mm)] with a length to penetrate through the roof sheathing or a minimum of 3/4 inch (19.1 mm) into the roof sheathing.
Exception: As an alternative, adhered underlayment complying with ASTM D 1970 shall be permitted.
1507.7.3.2 Underlayment Application. Underlayment shall be installed using one of the following methods:
1. Two layer underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or Type IV or ASTM D 6757: Apply a 19-inch (483 mm) strip of underlayment felt parallel to and starting at the eaves, fastened sufficiently to hold in place. Starting at the eave, apply 36-inch-wide (914 mm) sheets of underlayment, overlapping successive sheets 19 inches (483 mm), and fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with one row in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened in accordance with this section and the manufacturer’s recommendations.
2. One layer underlayment shall comply with ASTM D 226, Type II or ASTM D 4869, Type IV or ASTM D 6757: Underlayment shall be applied shingle fashion, parallel to and starting from the eave and lapped 2 inches (51 mm), fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with two staggered rows in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). Synthetic underlayment shall be fastened in accordance with this section and the manufacturer’s recommendations End laps shall be offset by 6 feet (1829 mm).
3. As an alternative, the entire roof deck shall be covered with an approved self-adhering polymer modified bitumen sheet meeting ASTM D 1970 or an approved self-adhering synthetic underlayment installed in accordance with the manufacturer’s installation instructions.
1507.7.4 Ice barrier. Reserved.
In areas where the average daily temperature in January is 25°F (-4°C) or less or where there is a possibility of ice forming along the eaves causing a backup of water, an ice barrier that consists of at least two layers of underlayment cemented together or of a self-adhering polymer-modified bitumen sheet shall extend from the lowest edges of all roof surfaces to a point at least 24 inches (610 mm) inside the exterior wall line of the building.
Exception: Detached accessory structures that contain no conditioned floor area.
1507.7.5 Material standards. Slate shingles shall comply with ASTM C 406.
1507.7.6 Application. Minimum headlap for slate shingles shall be in accordance with Table 1507.7.6. Slate shingles shall be secured to the roof with two fasteners per slate.
TABLE 1507.7.6
SLATE SHINGLE HEADLAP
|SLOPE |HEADLAP |
| |(inches) |
|4:12 < slope < 8:12 |4 |
|8:12 < slope < 20:12 |3 |
|slope = 20:12 |2 |
|For SI: 1 inch = 25.4 mm. |
1507.7.7 Flashing. Flashing and counterflashing shall be made with sheet metal. Valley flashing shall be a minimum of 15 16 inches (381 mm) wide. Valley and flashing metal shall be a minimum uncoated thickness of 0.0179-inch (0.455 mm) zinc-coated G90 thickness provided in Table 1503.2 nonferrous metal or stainless steel. Chimneys, stucco or brick walls shall have a minimum of two plies of felt for a cap flashing consisting of a 4-inch-wide (102 mm) strip of felt set in plastic cement and extending 1 inch (25 mm) above the first felt and a top coating of plastic cement. The felt shall extend over the base flashing 2 inches (51 mm).
(Mod R5281-R1 / AM)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.8 to read as shown:
|1507.8 Wood shingles. The installation of wood shingles shall comply with the provisions of this section and Table 1507.8. |
| |
| |
| |
|TABLE 1507.8 |
|WOOD SHINGLE AND SHAKE INSTALLATION |
| |
|ROOF ITEM |
|WOOD SHINGLES |
|WOOD SHAKES |
| |
|1. Roof slope |
|Wood shingles shall be installed on slopes of three units vertical in 12 units horizontal (3:12) or greater. |
|Wood shakes shall be installed on slopes of four units vertical in 12 units horizontal (4:12) or greater. |
| |
|2. Deck requirement |
| |
|Temperate climate |
|Shingles shall be applied to roofs with solid or spaced sheathing. Where spaced sheathing is used, sheathing boards shall not be less than |
|1” × 4” nominal dimensions and shall be spaced on center equal to the weather exposure to coincide with the placement of fasteners. |
|Shakes shall be applied to roofs with solid or spaced sheathing. Where spaced sheathing is used, sheathing boards shall not be less than 1”|
|× 4” nominal dimensions and shall be spaced on center equal to the weather exposure to coincide with the placement of fasteners. When 1” × |
|4” spaced sheathing is installed at 10 inches, boards must be installed between the sheathing boards. |
| |
|In areas where the average daily temperature in January is 25°F or less or where there is a possibility of ice forming along the eaves |
|causing a backup of water. |
|Solid sheathing required. |
|Solid sheathing is required. |
| |
|3. Interlayment |
|No requirements. |
|Interlayment shall comply with ASTM D 226, Type 1. |
| |
|4. Underlayment |
| |
| |
| |
|Temperate climate |
|Underlayment shall comply with ASTM D 226, Type 1. |
|Underlayment shall comply with ASTM D 226, Type 1. |
| |
|In areas where there is a possibility of ice forming along the eaves causing a backup of water. |
|An ice barrier that consists of at least two layers of underlayment cemented together or of a self-adhering polymer-modified bitumen sheet |
|shall extend from the eave's edge to a point at least 24 inches inside the exterior wall line of the building. |
|An ice barrier that consists of at least two layers of underlayment cemented together or of a self-adhering polymer-modified bitumen sheet |
|shall extend from the lowest edges of all roof surfaces to a point at least 24 inches inside the exterior wall line of the building. |
| |
|5. Application |
| |
| |
| |
|Attachment |
|Fasteners for wood shingles shall be hot-dipped galvanized or Type 304 (Type 316 for coastal areas) stainless steel with a minimum |
|penetration of 0.75 inch into the sheathing. For sheathing less than 0.5 inch thick, the fasteners shall extend through the sheathing. |
|Fasteners for wood shakes shall be hot-dipped galvanized or Type 304 (Type 316 for coastal areas) with a minimum penetration of 0.75 inch |
|into the sheathing. For sheathing less than 0.5 inch thick, the fasteners shall extend through the sheathing. |
| |
|No. of fasteners |
|Two per shingle. |
|Two per shake. |
| |
|Exposure |
|Weather exposures shall not exceed those set forth in Table 1507.8.7. |
|Weather exposures shall not exceed those set forth in Table 1507.9.8. |
| |
|Method |
|Shingles shall be laid with a side lap of not less than 1.5 inches between joints in courses, and no two joints in any three adjacent |
|courses shall be in direct alignment. Spacing between shingles shall be 0.25 to 0.375 inch. |
|Shakes shall be laid with a side lap of not less than 1.5 inches between joints in adjacent courses. Spacing between shakes shall not be |
|less than 0.375 inch or more than 0.625 inch for shakes and taper sawn shakes of naturally durable wood and shall be 0.25 to 0.375 inch for|
|preservative-treated taper sawn shakes. |
| |
|Flashing |
|In accordance with Section 1507.8.8. |
|In accordance with Section 1507.9.9. |
| |
| |
| |
| For SI: 1 inch = 25.4 mm, °C = [(°F) - 32]/1.8. |
|1507.8.1 Deck requirements. Wood shingles shall be installed on solid or spaced sheathing. Where spaced sheathing is used, sheathing boards|
|shall not be less than 1-inch by 4-inch (25 mm by 102 mm) nominal dimensions and shall be spaced on centers equal to the weather exposure |
|to coincide with the placement of fasteners. |
|1507.8.1.1 Solid sheathing required. Reserved. Solid sheathing is required in areas where the average daily temperature in January is 25°F|
|(-4°C) or less or where there is a possibility of ice forming along the eaves causing a backup of water. |
|1507.8.2 Deck slope. Wood shingles shall be installed on slopes of three units vertical in 12 units horizontal (25-percent slope) or |
|greater. |
|1507.8.3 Underlayment. Underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869 Type II or IV. |
|1507.8.3.1 Underlayment and high wind. Reserved. |
|Underlayment applied in areas subject to high winds [Vasd greater than 110 mph (49 m/s) as determined in accordance with Section 1609.3.1] |
|shall be applied with corrosion-resistant fasteners in accordance with the manufacturer's installation instructions. Fasteners are to be |
|applied along the overlap not farther apart than 36 inches (914 mm) on center. |
|Underlayment installed where Vasd, in accordance with Section 1609.3.1, equals or exceeds 120 mph (54 m/s) shall comply with ASTM D 226 |
|Type II or ASTM D 4869 Type IV. The underlayment shall be attached in a grid pattern of 12 inches (305 mm) between side laps with a 6-inch |
|spacing (152 mm) at the side laps. Underlayment shall be applied in accordance with the manufacturer's installation instructions except all|
|laps shall be a minimum of 4 inches (102 mm). Underlayment shall be attached using metal or plastic cap nails with a head diameter of not |
|less than 1 inch (25 mm) with a thickness of at least 32-gauge [0.0134 inch (0.34 mm)] sheet metal. The cap nail shank shall be a minimum |
|of 12 gauge [0.105 inch (2.67 mm)] with a length to penetrate through the roof sheathing or a minimum of 3/4 inch (19.1 mm) into the roof |
|sheathing. |
|Exception: As an alternative, adhered underlayment complying with ASTM D 1970 shall be permitted. |
|1507.8.3.2 Underlayment Application. Underlayment shall be installed using one of the following methods: |
| 1. Two layer underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or Type IV: Apply a 19-inch (483 |
|mm) strip of underlayment felt parallel to and starting at the eaves, fastened sufficiently to hold in place. Starting at the eave, apply |
|36-inch-wide (914 mm) sheets of underlayment, overlapping successive sheets 19 inches (483 mm), and fastened with 1 inch (25 mm) round |
|plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with one row in the field of the sheet with a maximum |
|fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). |
|2. One layer underlayment shall comply with ASTM D 226, Type II or ASTM D 4869, Type IV: Underlayment shall be applied shingle |
|fashion, parallel to and starting from the eave and lapped 2 inches (51 mm), fastened with 1 inch (25 mm) round plastic cap, metal cap |
|nails or nails and tin-tabs attached to a nailable deck with two staggered rows in the field of the sheet with a maximum fastener spacing |
|of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). End laps shall be offset by 6 feet (1829 mm). |
|1507.8.4 Ice barrier. Reserved. |
|In areas where there has been a history of ice forming along the eaves causing a backup of water, an ice barrier that consists of at least |
|two layers of underlayment cemented together or of a self-adhering polymer-modified bitumen sheet shall be used in lieu of normal |
|underlayment and extend from the lowest edges of all roof surfaces to a point at least 24 inches (610 mm) inside the exterior wall line of |
|the building. |
|Exception: Detached accessory structures that contain no conditioned floor area. |
| |
|1507.8.5 Material standards. Wood shingles shall be of naturally durable wood and comply with the requirements of Table 1507.8.5. |
| |
| |
| |
|TABLE 1507.8.5 |
|WOOD SHINGLE MATERIAL REQUIREMENTS |
| |
|MATERIAL |
|APPLICABLE |
|MINIMUM GRADES |
|GRADING RULES |
| |
|Wood shingles of naturally |
|durable wood |
|1, 2 or 3 |
|CSSB |
| |
| CSSB = Cedar Shake and Shingle Bureau |
| |
| 1507.8.6 Attachment. Fasteners for wood shingles shall be corrosion resistant with a minimum penetration of 3/4 inch (19.1 mm) into the |
|sheathing. For sheathing less than 1/2 inch (12.7 mm) in thickness, the fasteners shall extend through the sheathing. Each shingle shall be|
|attached with a minimum of two fasteners. |
|1507.8.7 Application. Wood shingles shall be laid with a side lap not less than 11/2 inches (38 mm) between joints in adjacent courses, and|
|not be in direct alignment in alternate courses. Spacing between shingles shall be 1/4 to 3/8 inches (6.4 to 9.5 mm). Weather exposure for |
|wood shingles shall not exceed that set in Table 1507.8.7. |
| |
| |
|TABLE 1507.8.7 |
|WOOD SHINGLE WEATHER EXPOSURE AND ROOF SLOPE |
| |
|ROOFING MATERIAL |
|LENGTH (inches) |
|GRADE |
|EXPOSURE (inches) |
| |
| |
| |
| |
|3:12 pitch |
|to < 4:12 |
|4:12 pitch or steeper |
| |
|Shingles of naturally durable wood |
|16 |
|No. 1 |
|No. 2 |
|No. 3 |
|3.75 |
|3.5 |
|3 |
|5 |
|4 |
|3.5 |
| |
| |
|18 |
|No. 1 |
|No. 2 |
|No. 3 |
|4.25 |
|4 |
|3.5 |
|5.5 |
|4.5 |
|4 |
| |
| |
|24 |
|No. 1 |
|No. 2 |
|No. 3 |
|5.75 |
|5.5 |
|5 |
|7.5 |
|6.5 |
|5.5 |
| |
| For SI: 1 inch = 25.4 mm. |
| |
|1507.8.8 Flashing. At the juncture of the roof and vertical surfaces, flashing and counterflashing shall be provided in accordance with the|
|manufacturer's installation instructions, and where of metal, shall not be less than 0.019-inch (0.48 mm) (No. 26 galvanized sheet gage) |
|corrosion-resistant metal comply with Table 1503.2. The valley flashing shall extend at least 11 inches (279 mm) from the centerline each |
|way and have a splash diverter rib not less than 1 inch (25 mm) high at the flow line formed as part of the flashing. Sections of flashing |
|shall have an end lap of not less than 4 inches (102 mm). For roof slopes of three units vertical in 12 units horizontal (25-percent slope)|
|and over, the valley flashing shall have a 36-inch-wide (914 mm) layer of underlayment of either one layer of Type I underlayment running |
|the full length of the valley or a self-adhering polymer-modified bitumen sheet complying with ASTM D 1970, in addition to other required |
|underlayment. In areas where the average daily temperature in January is 25°F (-4°C) or less or where there is a possibility of ice forming|
|along the eaves causing a backup of water, the metal valley flashing underlayment shall be solidly cemented to the roofing underlayment for|
|slopes under seven units vertical in 12 units horizontal (58-percent slope) or self-adhering polymer-modified bitumen sheet shall be |
|installed. |
| |
(Mod R5286-R1 / AM)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.9 to read as shown:
1507.9 Wood shakes. The installation of wood shakes shall comply with the provisions of this section and Table 1507.8.
1507.9.1 Deck requirements. Wood shakes shall only be used on solid or spaced sheathing. Where spaced sheathing is used, sheathing boards shall not be less than 1-inch by 4-inch (25 mm by 102 mm) nominal dimensions and shall be spaced on centers equal to the weather exposure to coincide with the placement of fasteners. Where 1-inch by 4-inch (25 mm by 102 mm) spaced sheathing is installed at 10 inches (254 mm) o.c., additional 1-inch by 4-inch (25 mm by 102 mm) boards shall be installed between the sheathing boards.
1507.9.1.1 Solid sheathing required. Reserved.
Solid sheathing is required in areas where the average daily temperature in January is 25°F (-4°C) or less or where there is a possibility of ice forming along the eaves causing a backup of water.
1507.9.2 Deck slope. Wood shakes shall only be used on slopes of four units vertical in 12 units horizontal (33-percent slope) or greater.
1507.9.3 Underlayment. Underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or IV.
1507.9.3.1 Underlayment and high wind. Reserved.
Underlayment applied in areas subject to high winds [Vasd greater than 110 mph (49 m/s) as determined in accordance with Section 1609.3.1] shall be applied with corrosion-resistant fasteners in accordance with the manufacturer's installation instructions. Fasteners are to be applied along the overlap not farther apart than 36 inches (914 mm) on center.
Underlayment installed where Vasd, in accordance with Section 1609.3.1, equals or exceeds 120 mph (54 m/s) shall comply with ASTM D 226 Type II or ASTM D 4869 Type IV. The underlayment shall be attached in a grid pattern of 12 inches (305 mm) between side laps with a 6-inch spacing (152 mm) at the side laps. Underlayment shall be applied in accordance with the manufacturer's installation instructions except all laps shall be a minimum of 4 inches (102 mm). Underlayment shall be attached using metal or plastic cap nails with a head diameter of not less than 1 inch (25 mm) with a thickness of at least 32-gauge [0.0134 inch (0.34 mm)] sheet metal. The cap nail shank shall be a minimum of 12 gauge [0.105 inch (2.67 mm)] with a length to penetrate through the roof sheathing or a minimum of 3/4 inch (19.1 mm) into the roof sheathing.
Exception: As an alternative, adhered underlayment complying with ASTM D 1970 shall be permitted.
1507.9.3.2 Underlayment Application. Underlayment shall be installed using one of the following methods:
1. Two layer underlayment shall comply with ASTM D 226, Type I or Type II or ASTM D 4869, Type II or Type IV: Apply a 19-inch (483 mm) strip of underlayment felt parallel to and starting at the eaves, fastened sufficiently to hold in place. Starting at the eave, apply 36-inch-wide (914 mm) sheets of underlayment, overlapping successive sheets 19 inches (483 mm), and fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with one row in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm).
2. One layer underlayment shall comply with ASTM D 226, Type II or ASTM D 4869, Type IV: Underlayment shall be applied shingle fashion, parallel to and starting from the eave and lapped 2 inches (51 mm), fastened with 1 inch (25 mm) round plastic cap, metal cap nails or nails and tin-tabs attached to a nailable deck with two staggered rows in the field of the sheet with a maximum fastener spacing of 12 in. o.c. (305 mm), and one row at the overlaps fastened 6 in. o.c. (152 mm). End laps shall be offset by 6 feet (1829 mm).
1507.9.4 Ice barrier. Reserved.
In areas where there has been a history of ice forming along the eaves causing a backup of water, an ice barrier that consists of at least two layers of underlayment cemented together or of a self-adhering polymer-modified bitumen sheet shall be used in lieu of normal underlayment and extend from the lowest edges of all roof surfaces to a point at least 24 inches (610 mm) inside the exterior wall line of the building.
Exception: Detached accessory structures that contain no conditioned floor area.
1507.9.5 Interlayment. Interlayment shall comply with ASTM D 226, Type I.
1507.9.6 Material standards. Wood shakes shall comply with the requirements of Table 1507.9.6.
TABLE 1507.9.6
WOOD SHAKE MATERIAL REQUIREMENTS
|MATERIAL |MINIMUM GRADES |APPLICABLE GRADING RULES |
|Wood shakes of naturally durable wood |1 |CSSB |
|Taper sawn shakes of naturally durable wood |1 or 2 |CSSB |
|Preservative-treated shakes and shingles of naturally |1 |CSSB |
|durable wood | | |
|Fire-retardant-treated shakes and shingles of naturally |1 |CSSB |
|durable wood | | |
|Preservative-treated taper sawn shakes of Southern pine |1 or 2 |TFS |
|treated in accordance with AWPA U1 (Commodity | | |
|Specification A, Use Category 3B and Section 5.6) | | |
| |
| |
| CSSB = Cedar Shake and Shingle Bureau. |
|TFS = Forest Products Laboratory of the Texas Forest Services. |
1507.9.7 Attachment. Fasteners for wood shakes shall be corrosion resistant with a minimum penetration of 3/4 inch (19.1 mm) into the sheathing. For sheathing less than1/2 inch (12.7 mm) in thickness, the fasteners shall extend through the sheathing. Each shake shall be attached with a minimum of two fasteners.
1507.9.8 Application. Wood shakes shall be laid with a side lap not less than 11/2 inches (38 mm) between joints in adjacent courses. Spacing between shakes in the same course shall be 3/8 to 5/8 inches (9.5 to 15.9 mm) for shakes and taper sawn shakes of naturally durable wood and shall be 1/4 to 3/8 inch (6.4 to 9.5 mm) for preservative taper sawn shakes. Weather exposure for wood shakes shall not exceed those set in Table 1507.9.8.
1507.9.9 Flashing. At the juncture of the roof and vertical surfaces, flashing and counterflashing shall be provided in accordance with the manufacturer's installation instructions, and where of metal, shall not be less than 0.019-inch (0.48 mm) (No. 26 galvanized sheet gage) corrosion-resistant metal comply with Table 1503.2. The valley flashing shall extend at least 11 inches (279 mm) from the centerline each way and have a splash diverter rib not less than 1 inch (25 mm) high at the flow line formed as part of the flashing. Sections of flashing shall have an end lap of not less than 4 inches (102 mm). For roof slopes of three units vertical in 12 units horizontal (25-percent slope) and over, the valley flashing shall have a 36-inch-wide (914 mm) layer of underlayment of either one layer of Type I underlayment running the full length of the valley or a self-adhering polymer-modified bitumen sheet complying with ASTM D 1970, in addition to other required underlayment. In areas where the average daily temperature in January is 25°F (-4°C) or less or where there is a possibility of ice forming along the eaves causing a backup of water, the metal valley flashing underlayment shall be solidly cemented to the roofing underlayment for slopes under seven units vertical in 12 units horizontal (58-percent slope) or self-adhering polymer-modified bitumen sheet shall be installed.
(Mod R5284 – R1 / AM)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.10 to read as shown:
1507.10 Built-up roofs. The installation of built-up roofs shall comply with the provisions of this section.
1507.10.1 Slope. Built-up roofs shall have a design slope of a minimum of one-fourth unit vertical in 12 units horizontal (2-percent slope) for drainage, except for coal-tar built-up roofs that shall have a design slope of a minimum one-eighth unit vertical in 12 units horizontal (1-percent slope).
1507.10.2 Material standards. Built-up roof covering materials shall comply with the standards in Table 1507.10.2 or UL 55A.
TABLE 1507.10.2
BUILT-UP ROOFING MATERIAL STANDARDS
|MATERIAL STANDARD |STANDARD |
|Acrylic coatings used in roofing |ASTM D 6083 |
|Aggregate surfacing |ASTM D 1863 |
|Asphalt adhesive used in roofing |ASTM D 3747 |
|Asphalt cements used in roofing |ASTM D 3019; D 2822; |
| |D 4586 |
|Asphalt-coated glass fiber base sheet |ASTM D 4601 |
|Asphalt coatings used in roofing |ASTM D 1227; D 2823; |
| |D 2824; D 4479 |
|Asphalt glass felt |ASTM D 2178 |
|Asphalt primer used in roofing |ASTM D 41 |
|Asphalt-saturated and asphalt-coated organic felt base sheet |ASTM D 2626 |
|Asphalt-saturated organic felt (perforated) |ASTM D 226 |
|Asphalt used in roofing |ASTM D 312 |
|Coal-tar cements used in roofing |ASTM D 4022; D 5643 |
|Coal-tar saturated organic felt |ASTM D 227 |
|Coal-tar pitch used in roofing |ASTM D 450; Type I or II |
|Coal-tar primer used in roofing, dampproofing and waterproofing |ASTM D 43 |
|Glass mat, coal tar |ASTM D 4990 |
|Glass mat, venting type |ASTM D 4897 |
|Mineral-surfaced inorganic cap sheet |ASTM D 3909 |
|Thermoplastic fabrics used in roofing |ASTM D 5665, D 5726 |
1507.10.3 Red rosin paper. Red rosin paper shall be used when the membrane is applied directly to a wood deck or cementitious fiber decks.
(Mod R5270 / AS)
Section 1507 – Requirements for Roof Coverings
Change Section 1507.17 to read as shown:
Section 1507.17 Photovoltaic modules/shingles. Change to read as shown:
1507.17 Photovoltaic modules/shingles. The installation Building integrated P photovoltaic roofing modules/shingles. The installation of building integrated P photovoltaic roofing modules/shingles shall comply with the provisions of this section.
1507.17.1 Material standards. Building integrated P photovoltaic roofing modules/shingles shall be listed and labeled in accordance with UL 1703.
1507.17.2 Attachment. Building integrated P photovoltaic roofing modules/shingles shall be attached in accordance with the manufacturer's installation instructions.
1507.17.3 Wind resistance. Building integrated P photovoltaic roofing modules/shingles shall be tested in accordance with procedures and acceptance criteria in ASTM D 3161 or TAS 107. Building integrated P photovoltaic roofing modules/shingles shall comply with the classification requirements of Table 1507.2.7.1(2) for the appropriate maximum nominal design basic wind speed. Building integrated P photovoltaic roofing modules/shingle packaging shall bear a label to indicate compliance with the procedures in ASTM D 3161 or TAS 107 and the required classification from Table 1507.2.7.1(2) .
(Mod R5280 / AS)
Section 1508 – Roof Insulation
Change Section 1508.1 to read as shown:
Section 1508.1 General. Change to read as shown:
1508.1 General. The use of above-deck thermal insulation shall be permitted provided such insulation is covered with an approved roof covering and passes the tests of FM 4450, FM 4454 or UL 1256 (for wind uplift resistance), and ANSI/UL 263 or ASTM E119 (for fire resistance), when tested as an assembly. (No change to the remainder of text)
(Mod R5738-R1 / AM)
Section 1508 – Roof Insulation
Change Section 1508.2 to read as shown:
Section 1508.2 Material standards. Change to read as shown:
1508.2 Material standards. Above-deck thermal insulation board shall comply with the standards in Table 1508.2.
TABLE 1508.2
MATERIAL STANDARDS FOR ROOF INSULATION
|Cellular glass board |ASTM C 552 |
|Composite boards |ASTM C 1289, Type III, IV, V or VI |
|Expanded polystyrene |ASTM C 578 |
|Extruded polystyrene board |ASTM C 578 |
|Lightweight insulating concrete |ASTM C 495, C513, C796, C869 |
|Perlite board |ASTM C 728 |
|Polyisocyanurate board |ASTM C 1289, Type I or Type II |
|Wood fiberboard |ASTM C 208 |
(Mod R5739 / AS)
Section 1509 – Rooftop Structures
Change Section 1509 to read as shown:
1509.1 General. The provisions of this section shall govern the construction of rooftop structures.
1509.2 Penthouses. Penthouses in compliance with Sections 1509.2.1 through 1509.2.5 shall be considered as a portion of the story directly below the roof deck on which such penthouses are located. All other penthouses shall be considered as an additional story of the building.
1509.2.1 Height above roof deck. Penthouses constructed on buildings of other than Type I construction shall not exceed 18 feet (5486 mm) in height above the roof deck as measured to the average height of the roof of the penthouse.
Exceptions:
1. Where used to enclose tanks or elevators that travel to the roof level, penthouses shall be permitted to have a maximum height of 28 feet (8534 mm) above the roof deck.
2. Penthouses located on the roof of buildings of Type I construction shall not be limited in height.
1509.2.2 Area limitation. The aggregate area of penthouses and other enclosed rooftop structures shall not exceed one-third the area of the supporting roof deck. Such penthouses and other enclosed rooftop structures shall not be required to be included in determining the building area or number of stories as regulated by Section 503.1. The area of such penthouses shall not be included in determining the fire area specified in Section 901.7.
1509.2.3 Use limitations. Penthouses shall not be used for purposes other than the shelter of mechanical or electrical equipment, tanks, or vertical shaft openings in the roof assembly.
1509.2.4 Weather protection. Provisions such as louvers, louver blades or flashing shall be made to protect the mechanical and electrical equipment and the building interior from the elements.
1509.2.5 Type of construction. Penthouses shall be constructed with walls, floors and roofs as required for the type of construction of the building on which such penthouses are built.
Exceptions:
1. On buildings of Type I construction, the exterior walls and roofs of penthouses with a fire separation distance greater than 5 feet (1524 mm) and less than 20 feet (6096 mm) shall be permitted to have not less than a 1-hour fire-resistance rating. The exterior walls and roofs of penthouses with a fire separation distance of 20 feet (6096 mm) or greater shall not be required to have a fire-resistance rating.
2. On buildings of Type I construction two stories or less in height above grade plane or of Type II construction, the exterior walls and roofs of penthouses with a fire separation distance greater than 5 feet (1524 mm) and less than 20 feet (6096 mm) shall be permitted to have not less than a 1-hour fire-resistance rating or a lesser fire-resistance rating as required by Table 602 and be constructed of fire-retardant-treated wood. The exterior walls and roofs of penthouses with a fire separation distance of 20 feet (6096 mm) or greater shall be permitted to be constructed of fire-retardant-treated wood and shall not be required to have a fire-resistance rating. Interior framing and walls shall be permitted to be constructed of fire-retardant-treated wood.
3. On buildings of Type III, IV or V construction, the exterior walls of penthouses with a fire separation distance greater than 5 feet (1524 mm) and less than 20 feet (6096 mm) shall be permitted to have not less than a 1-hour fire-resistance rating or a lesser fire-resistance rating as required by Table 602. On buildings of Type III, IV or VA construction, the exterior walls of penthouses with a fire separation distance of 20 feet (6096 mm) or greater shall be permitted to be of Type IV or noncombustible construction or fire-retardant-treated wood and shall not be required to have a fire-resistance rating.
1509.3 Tanks. Tanks having a capacity of more than 500 gallons (2 m3) located on the roof deck of a building shall be supported on masonry, reinforced concrete, steel or Type IV construction provided that, where such supports are located in the building above the lowest story, the support shall be fire-resistance rated as required for Type IA construction.
1509.3.1 Valve and drain. In the bottom or on the side near the bottom of the tank, a pipe or outlet, fitted with a suitable quick-opening valve for discharging the contents into a drain in an emergency shall be provided.
1509.3.2 Location. Tanks shall not be placed over or near a stairway or an elevator shaft, unless there is a solid roof or floor underneath the tank.
1509.3.3 Tank cover. Unenclosed roof tanks shall have covers sloping toward the perimeter of the tanks.
1509.4 Cooling towers. Cooling towers located on the roof deck of a building and greater than 250 square feet (23.2 m2) in base area or greater than 15 feet (4572 mm) in height above the roof deck, as measured to the highest point on the cooling tower, where the roof is greater than 50 feet (15 240 mm) in height above grade plane shall be constructed of noncombustible materials. The base area of cooling towers shall not exceed one-third the area of the supporting roof deck.
Exception: Drip boards and the enclosing construction shall be permitted to be of wood not less than 1 inch (25 mm) nominal thickness, provided the wood is covered on the exterior of the tower with noncombustible material.
1509.5 Towers, spires, domes and cupolas. Towers, spires, domes and cupolas shall be of a type of construction having fire-resistance ratings not less than required for the building on top of which such tower, spire, dome or cupola is built. Towers, spires, domes and cupolas greater than 85 feet (25 908 mm) in height above grade plane as measured to the highest point on such structures, and either greater than 200 square feet (18.6 m2) in horizontal area or used for any purpose other than a belfry or an architectural embellishment, shall be constructed of and supported on Type I or II construction.
1509.5.1 Noncombustible construction required. Towers, spires, domes and cupolas greater than 60 feet (18 288 mm) in height above the highest point at which such structure contacts the roof as measured to the highest point on such structure, or that exceeds 200 square feet (18.6 m2) in area at any horizontal section, or which is intended to be used for any purpose other than a belfry or architectural embellishment, or is located on the top of a building greater than 50 feet (1524 mm) in building height shall be constructed of and supported by noncombustible materials and shall be separated from the building below by construction having a fire-resistance rating of not less than 1.5 hours with openings protected in accordance with Section 712. Such structures located on the top of a building greater than 50 feet (15 240 mm) in building height shall be supported by noncombustible construction.
1509.5.2 Towers and spires. Enclosed towers and spires shall have exterior walls constructed as required for the building on top of which such towers and spires are built. The roof covering of spires shall not be less than the same class of roof covering required for the building on top of which the spire is located.
1509.6 Mechanical equipment screens. Mechanical equipment screens shall be constructed of the materials specified for the exterior walls in accordance with the type of construction of the building. Where the fire separation distance is greater than 5 feet (1524 mm), mechanical equipment screens shall not be required to comply with the fire-resistance rating requirements.
1509.6.1 Height limitations. Mechanical equipment screens shall not exceed 18 feet (5486 mm) in height above the roof deck, as measured to the highest point on the mechanical equipment screen.
Exception: Where located on buildings of Type IA construction, the height of mechanical equipment screens shall not be limited.
1509.6.2 Types I, II, III and IV construction. Regardless of the requirements in Section 1509.6, mechanical equipment screens shall be permitted to be constructed of combustible materials where located on the roof decks of building of Type I, II, III or IV construction in accordance with any one of the following limitations:
1. The fire separation distance shall not be less than 20 feet (6096 mm) and the height of the mechanical equipment screen above the roof deck shall not exceed 4 feet (1219 mm) as measured to the highest point on the mechanical equipment screen.
2. The fire separation distance shall not be less than 20 feet (6096 mm) and the mechanical equipment screen shall be constructed of fire-retardant-treated wood complying with Section 2303.2 for exterior installation.
3. Where exterior wall covering panels are used, the panels shall have a flame spread index of 25 or less when tested in the minimum and maximum thicknesses intended for use with each face tested independently in accordance with ASTM E 84 or UL 723. The panels shall be tested in the minimum and maximum thicknesses intended for use in accordance with, and shall comply with the acceptance criteria of, NFPA 285 and shall be installed as tested. Where the panels are tested as part of an exterior wall assembly in accordance with NFPA 285, the panels shall be installed on the face of the mechanical equipment screen supporting structure in the same manner as they were installed on the tested exterior wall assembly.
1509.6.3 Type V construction. The height of mechanical equipment screens located on the roof decks of buildings of Type V construction, as measured from grade plane to the highest point on the mechanical equipment screen, shall be permitted to exceed the maximum building height allowed for the building by other provisions of this code where complying with any one of the following limitations, provided the fire separation distance is greater than 5 feet (1524 mm):
1. Where the fire separation distance is not less than 20 feet (6096 mm), the height above grade plane of the mechanical equipment screen shall not exceed 4 feet (1219 mm) more than the maximum building height allowed;
2. The mechanical equipment screen shall be constructed of noncombustible materials;
3. The mechanical equipment screen shall be constructed of fire-retardant-treated wood complying with Section 2303.2 for exterior installation; or
4. Where the fire separation distance is not less than 20 feet (6096 mm), the mechanical equipment screen shall be constructed of materials having a flame spread index of 25 or less when tested in the minimum and maximum thicknesses intended for use with each face tested independently in accordance with ASTM E 84 or UL 723.
1509.6.4 Equipment and appliances on roofs or elevated structures. Where equipment and appliances requiring access are installed on roofs or elevated structures at a height exceeding 16 feet (4877 mm), such access shall be provided by a permanent approved means of access, the extent of which shall be from grade or floor level to the equipment and appliances' level service space. Such access shall not require climbing over obstructions greater than 30 inches (762 mm) high or walking on roofs having a slope greater than 4 units vertical in 12 units horizontal (33-percent slope).
Permanent ladders installed to provide the required access shall comply with the following minimum design criteria:
1. The side railing shall extend above the parapet or roof edge not less than 30 inches (762 mm).
2. Ladders shall have rung spacing not to exceed 14 inches (356 mm) on center.
3. Ladders shall have a toe spacing not less than 6 inches (152 mm) deep.
4. There shall be a minimum of 18 inches (457 mm) between rails.
5. Rungs shall have a minimum 0.75-inch (19 mm) diameter and be capable of withstanding a 300-pound (136.1 kg) load.
6. Ladders over 30 feet (9144 mm) in height shall be provided with offset sections and landings capable of withstanding 100 pounds (488.2 kg/m2) per square foot.
7. Ladders shall be protected against corrosion by approved means. Catwalks installed to provide the required access shall be not less than 24 inches (610 mm) wide and shall have railings as required for service platforms.
Exception: This section shall not apply to Group R-3 occupancies.
1509.6.5 Mechanical units. Roof mounted mechanical units shall be mounted on curbs raised a minimum of 8 inches (203 mm) above the roof surface, or where roofing materials extend beneath the unit, on raised equipment supports providing a minimum clearance height in accordance with Table 1509.7.
TABLE 1509.6.5
CLEARANCE BELOW RAISED ROOF MOUNTED MECHANICAL UNITS
|WIDTH OF MECHANICAL UNIT |MINIMUM CLEARANCE ABOVE |
|(inches) |SURFACES (inches) |
|< 24 |14 |
|24 < 36 |18 |
|36 < 48 |24 |
|48 < 60 |30 |
|> 60 |48 |
| For SI: 1 inch = 25.4 mm. |
Exception: In buildings where the existing rooftop equipment, in the opinion of the building official, provides sufficient clearance to repair, recover, replace and/or maintain the roofing system or any of its components, such existing equipment need not comply with Table 1509.6.5
1509.7 Photovoltaic systems. Rooftop mounted photovoltaic systems shall be designed in accordance with this section.
1509.7.1 Wind resistance. Rooftop mounted photovoltaic systems shall be designed for wind loads for component and cladding in accordance with Chapter 16 using an effective wind area based on the dimensions of a single unit frame.
1509.7.2 Fire classification. Rooftop mounted photovoltaic systems shall have the same fire classification as the roof assembly required by Section 1505.
1509.7.3 Installation. Rooftop mounted photovoltaic systems shall be installed in accordance with the manufacturer's installation instructions.
1509.7.4 Photovoltaic panels and modules. Photovoltaic panels and modules mounted on top of a roof shall be listed and labeled in accordance with UL 1703 and shall be installed in accordance with the manufacturer's installation instructions.
1509.8 Other rooftop structures. Rooftop structures not regulated by Sections 1509.2 through 1509.7 shall comply with Sections 1509.8.1 through 1509.8.5 as applicable.
1509.8.1 Aerial supports. Aerial supports shall be constructed of noncombustible materials.
Exception: Aerial supports not greater than 12 feet (3658 mm) in height as measured from the roof deck to the highest point on the aerial supports shall be permitted to be constructed of combustible materials.
1509.8.2 Bulkheads. Bulkheads used for the shelter of mechanical or electrical equipment or vertical shaft openings in the roof assembly shall comply with Section 1509.2 as penthouses. Bulkheads used for any other purpose shall be considered as an additional story of the building.
1509.8.3 Dormers. Dormers shall be of the same type of construction as required for the roof in which such dormers are located or the exterior walls of the building.
1509.8.4 Fences. Fences and similar structures shall comply with Section 1509.6 as mechanical equipment screens.
1509.8.5 Flagpoles. Flagpoles and similar structures shall not be required to be constructed of noncombustible materials and shall not be limited in height or number.
(Mod R5288 / AS)
SECTION 1510
REROOFING
Section 1510 – Reroofing
Change Section 1510.3 to read as shown:
1510.3 Recovering versus replacement. New roof coverings shall not be installed without first removing all existing layers of roof coverings down to the roof deck where any of the following conditions occur:
1. Where the existing roof or roof covering is water soaked or has deteriorated to the point that the existing roof or roof covering is not adequate as a base for additional roofing.
2. Where the existing roof covering is wood shake, slate, clay, cement or asbestos-cement tile.
3. Where the existing roof has two or more applications of any type of roof covering.
4. When blisters exist in any roofing, unless blisters are cut or scraped open and remaining materials secured down before applying additional roofing.
5. Where the existing roof is to be used for attachment for a new roof system and compliance with the securement provisions of Section 1504.1 cannot be met.
Exceptions:
1. Complete and separate roofing systems, such as standing-seam metal roof systems, that are designed to transmit the roof loads directly to the building's structural system and that do not rely on existing roofs and roof coverings for support, shall not require the removal of existing roof coverings.
2. Reserved. Metal panel, metal shingle and concrete and clay tile roof coverings shall be permitted to be installed over existing wood shake roofs when applied in accordance with Section 1510.4.
3. The application of a new protective coating over an existing spray polyurethane foam roofing system shall be permitted without tear-off of existing roof coverings.
4. Where the existing roof assembly includes an ice barrier membrane that is adhered to the roof deck, the existing ice barrier membrane shall be permitted to remain in place and covered with an additional layer of ice barrier membrane in accordance with Section 1507.
(Mod R5413 / AS)
Chapter 16 – Structural Design
Florida Specific Amendment
Section 1601 General
Change Section 1601.1 to read as shown.
1601.1 Scope. The provisions of this chapter shall govern the structural design of buildings, structures and portions thereof regulated by this code.
Exception: Buildings and structures located within the high-velocity hurricane zone shall comply with the provisions of Section 1605, 1607, 1611, Sections 1616 through 1626, and, as applicable in flood hazard areas, Section 1612.
(Mod S5425 / AS) (Mod S5263 / AS)
Section 1603 – Construction Documents
Change Section 1603.1.7 to read as shown:
1603.1.7 Flood design data. For buildings located in whole or in part in flood hazard areas as established in Section 1612.3, the documentation pertaining to design, if required in Section 1612.5, shall be included and the following information, referenced to the datum on the community’s Flood Insurance Rate Map (FIRM), shall be shown, regardless of whether flood loads govern the design of the building:
1. In flood hazard areas not subject to high-velocity wave action other than coastal high hazard areas, the elevation of the proposed lowest floor, including basement.
2. In flood hazard areas subject to high-velocity wave action coastal high hazard areas, the elevation to which any non-residential building will be dry floodproofed.
3. In flood hazard areas subject to high-velocity wave action coastal high hazard areas, the proposed elevation of the bottom of the lowest horizontal structural member of the lowest floor, including basement.
(Mod SP5274 / AS)
Section 1604 – General Design Requirements
Change Table 1604.3 to read as shown:
TABLE 1604.3
DEFLECTION LIMITS a, b, c, h, i
|CONSTRUCTION |L |S or W f |D + Ld,g,j |
|Roof members:e | | | |
|Supporting plaster or stucco ceiling |l/360 |l/360 |l/240 |
|Supporting nonplaster ceiling |l/240 |l/240 |l/180 |
|Not supporting ceiling |l/180 |l/180 |l/120 |
|Members supporting screen surface |— |— |l/60 |
|Floor members |l/360 |— |l/240 |
|Exterior walls and interior partitions: | | | |
|With plaster or stucco finishes |— |l/360 |— |
|With other brittle finishes |— |l/240 |— |
|With flexible finishes |— |l/120 |— |
|Farm buildings |— |— |l/180 |
|Greenhouses |— |— |l /120 |
For SI: 1 foot = 304.8 mm.
a.- i. (No Change)
j. Screen surfaces shall be permitted to include a maximum of 25% solid flexible finishes.
(Mod S5729 / AS)
Section 1604 – General Design Requirements
Change Table 1604.5 to read as shown:
TABLE 1604.5
RISK CATEGORY OF BUILDINGS AND OTHER STRUCTURES
|RISK CATEGORY |NATURE OF OCCUPANCY |
|I |Buildings and other structures that represent a low hazard to human life in the event of failure, including but not |
| |limited to: |
| |• Agricultural facilities. |
| |• Certain temporary facilities. |
| |• Minor storage facilities. |
| |• Screen enclosures. |
|II |Buildings and other structures except those listed in Risk Categories I, III and IV |
|III |Buildings and other structures that represent a substantial hazard to human life in the event of failure, including but|
| |not limited to: |
| |• Buildings and other structures whose primary occupancy is public assembly with an occupant load greater than 300. |
| |• Buildings and other structures containing elementary school, secondary school or day care facilities with an occupant|
| |load greater than 250. |
| |• Buildings and other structures containing adult education facilities, such as colleges and universities, with an |
| |occupant load greater than 500. |
| |• Group I-2 occupancies with an occupant load of 50 or more resident care recipients but not having surgery or |
| |emergency treatment facilities. |
| |• Group I-3 occupancies. |
| |• Any other occupancy with an occupant load greater than 5,000a. |
| |• Power-generating stations, water treatment facilities for potable water, waste water treatment facilities and other |
| |public utility facilities not included in Risk Category IV. |
| |• Buildings and other structures not included in Risk Category IV containing quantities of toxic or explosive |
| |materials that: |
| |Exceed maximum allowable quantities per control area as given in Table 307.1(1) or 307.1(2) or per outdoor control area|
| |in accordance with the International Florida Fire Prevention Code; and |
| |Are sufficient to pose a threat to the public if releasedb. |
|IV |Buildings and other structures designated as essential facilities, including but not limited to: |
| |• Group I-2 occupancies having surgery or emergency treatment facilities. |
| |• Fire, rescue, ambulance and police stations and emergency vehicle garages. |
| |• Designated earthquake, hurricane or other emergency shelters. |
| |• Designated emergency preparedness, communications and operations centers and other facilities required for emergency |
| |response. |
| |• Power-generating stations and other public utility facilities required as emergency backup facilities for Risk |
| |Category IV structures. |
| |• Buildings and other structures containing quantities of highly toxic materials that: |
| |Exceed maximum allowable quantities per control area as given in Table 307.1(2) or per outdoor control area in |
| |accordance with the International Florida Fire Prevention Code; and |
| |Are sufficient to pose a threat to the public if releasedb. |
| |• Aviation control towers, air traffic control centers and emergency aircraft hangars. |
| |• Buildings and other structures having critical national defense functions. |
| |• Water storage facilities and pump structures required to maintain water pressure for fire suppression. |
a. For purposes of occupant load calculation, occupancies required by Table 1004.1.2 to use gross floor area calculations shall be permitted to use net floor areas to determine the total occupant load.
b. Where approved by the building official, the classification of buildings and other structures as Risk Category III or IV based on their quantities of toxic, highly toxic or explosive materials is permitted to be reduced to Risk Category II, provided it can be demonstrated by a hazard assessment in accordance with Section 1.5.3 of ASCE 7 that a release of the toxic, highly toxic or explosive materials is not sufficient to pose a threat to the public.
(Mod S5949 / AS)
Section 1607 – Live Loads
Change Table 1607.1 to read as shown:
TABLE 1607.1
MINIMUM UNIFORMLY DISTRIBUTED LIVE LOADS, Lo, AND
MINIMUM CONCENTRATED LIVE LOADSg
(No change to body of Table 1607.1)
Footnotes a. – g. (No change)
h. See Section 1604.8.3 (HVHZ shall comply with Section 1616.5) for decks attached to exterior walls.
Footnotes i. – m. (No change)
(Mod S5431 / AS)
Section 1609 – Wind loads
Change Section 1609.1 to read as shown:
1609.1 Applications. Buildings, structures and parts thereof shall be designed to withstand the minimum wind loads prescribed herein. Decreases in wind loads shall not be made for the effect of shielding by other structures. All exterior wall coverings and soffits shall be capable of resisting the design pressures specified for walls for components and cladding loads in accordance with Section 1609.1.1. Manufactured soffits shall be labeled in accordance with Section 1710.9 of this code.
(Mod S5734 / AS)
Section 1609 – Wind loads
Change Section 1609.1.1 to read as shown:
1609.1.1 Determination of wind loads. Wind loads on every building or structure shall be determined in accordance with Chapters 26 to 30 of ASCE 7 or provisions of the alternate all-heights method in Section 1609.6. The type of opening protection required, the ultimate design wind speed, Vult, and the exposure category for a site is permitted to be determined in accordance with Section 1609 or ASCE 7. Wind shall be assumed to come from any horizontal direction and wind pressures shall be assumed to act normal to the surface considered.
Exceptions:
1. Subject to the limitations of Section 1609.1.1.1, the provisions of ICC 600 shall be permitted for applicable Group R-2 and R-3 buildings.
2. Subject to the limitations of Section 1609.1.1.1, residential structures using the provisions of AF&PA WFCM.
3. Subject to the limitations of Section 1609.1.1.1, residential structures using the provisions of AISI S230.
4. Designs using NAAMM FP 1001.
5. Designs using TIA-222 for antenna-supporting structures and antennas, provided the horizontal extent of Topographic Category 2 escarpments in Section 2.6.6.2 of TIA-222 shall be 16 times the height of the escarpment. Design using this standard shall be permitted for communication tower and steel antenna support structures.
6. Wind tunnel tests in accordance with Chapter 31 of ASCE 7.
7. Wind loads for screened enclosures shall be determined in accordance with Section 2002.4.
The wind speeds in Figures 1609A, 1609B and 1609C are ultimate design wind speeds, Vult, and shall be converted in accordance with Section 1609.3.1 to nominal design wind speeds, Vasd, when the provisions of the standards referenced in Exceptions 1,3,4 through and 5 are used unless the wind provisions in the standards are based on Ultimate Wind Speeds as specified in Figures 1609A, 1609B, or 1609C or Chapter 26 of ASCE 7.
(Mod S5608 / AS)
(Mod S5121-R1 / AM)
(Mod S5732 / AS)
Section 1609 – Wind Loads
Change Figures 1609A – 1609C to read as shown:
[pic]
[pic]
[pic]
(Mod S5118 / AM)
Section 1609 – Wind Loads
Change Section 1609.1.2 to read as shown:
1609.1.2 Protection of openings. In wind-borne debris regions, glazing glazed openings in buildings shall be impact resistant or protected with an impact-resistant covering meeting the requirements of , an approved impact-resistant standard or ASTM E 1996 and ASTM E 1886 referenced herein as follows: , SSTD 12, ANSI/DASMA 115 (for garage doors and rolling doors) or TAS 201, 202 and 203, AAMA 506. ASTM E 1996 and ASTM E 1886 referenced herein, or an approved impact-resistant standard as follows:
1. Glazed openings located within 30 feet (9.1 m) of grade shall meet the requirements of the Large Missile Test of ASTM E 1996.
2. Glazed openings located more than 30 feet (9.1 m) above grade shall meet the provisions of the Small Missile Test of ASTM E 1996.
3. Storage sheds that are not designed for human habitation and that have a floor area of 720 square feet (67 m2) or less are not required to comply with the mandatory windborne debris impact standards of this code.
4. Openings in sunrooms, balconies or enclosed porches constructed under existing roofs or decks are not required to be protected provided the spaces are separated from the building interior by a wall and all openings in the separating wall are protected in accordance with Section 1609.1.2 above. Such spaces shall be permitted to be designed as either partially enclosed or enclosed structures.
Exceptions: 1. – 3. (No change)
(Mod S5707-R1 / AM)
Section 1609 – Wind Loads
Change Table 1609.1.2 to read as shown:
TABLE 1609.1.2
WIND-BORNE DEBRIS PROTECTION FASTENING SCHEDULE FOR WOOD STRUCTURAL PANELSa, b, c, d
(Table Contents – No Change)
a. This table is based on a Vasd determined in accordance with Section 1609.3.1, of 140 mph wind speeds and a 45-foot mean roof height.
b. – d. (No Change)
(Mod S5610 / AS)
Section 1609 – Wind loads
Change Sections 1609.1.2.1 and 1609.1.2.2 to read as shown:
1609.1.2.1 Louvers. Louvers protecting intake and exhaust ventilation ducts not assumed to be open that are located within 30 feet (9144 mm) of grade shall meet requirements of AMCA 540 or shall be protected by an impact resistant cover complying with the large missile test of ASTM E 1996 or an approved impact-resistance standard. Louvers required to be open for life safety purposes such as providing a breathable atmosphere shall meet the requirements of AMCA 540.
(S5667 AM R1) (S5951 AS)
1609.1.2.2. Application of ASTM E 1996. The text of Section 6.2.2 of ASTM E 1996 shall be substituted as follows:
6.2.2 Unless otherwise specified, select the wind zone based on the strength design wind speed, Vult, as follows:
6.2.2.1 Wind Zone 1—130 mph < ultimate design wind speed, Vult < 140 mph.
6.2.2.2 Wind Zone 2—140 mph < ultimate design wind speed, Vult < 150 mph at greater than one mile (1.6 km) from the coastline. The coastline shall be measured from the mean high water mark.
6.2.2.3 Wind Zone 3—150 mph (58 m/s) ................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- chapter 1 design qualification bonneville
- general requirements technical safety bc
- chapter 1 design qualification and certification
- statement of requirements
- sizing how many btu s do i need
- florida building code
- florida building
- the following list of architectural dimensioning standards
- sample marketing requirements document
Related searches
- commercial building images
- importance of building customer relationships
- 3 minute team building games
- vocabulary building worksheets for adults
- government role in building businesses
- loans for building a home
- importance of building customer relations
- building a home financing options
- why is building relationships important
- free printable team building games
- benefits of building customer relationships
- building strong relationships at work