MECHANICAL SUPPLEMENTAL CONDITIONS - Saint Louis …



MECHANICAL PIPING SYMBOLSAUTOMATIC AIR VENT (AAV)GEAR OPERATED BUTTERFLY VALVETTHERMOMETERAUTOMATIC FLOW CONTROL VALVEAUTOMATIC TEMPERATURE CONTROLGLOBE VALVE (GL. V.)TRIPLE DUTY VALVE (TDV) VALVE (3-WAY)AUTOMATIC TEMPERATURE CONTROL HOSE END VALVEVALVE IN RISERVALVE (2-WAY)MANUAL AIR VENT (MAV)MWATER METERBALL VALVE (BV)CHECK VALVE (CV)PETE'S PLUG(TEMPERATURE & PRESSURE PORT)MEMERGENCY GAS SHUT-OFF VALVECIRCUIT SETTER (CS)PLUG VALVEFLEXIBLE PIPE CONNECTIONCOMPRESSED AIR QUICK-CONNECTPRESSURE GAUGEGAS SHUT-OFF VALVE (SOV)CONCENTRIC PIPE REDUCERPRESSURE REDUCING VALVE (PRV)GATE VALVE (GT. V.)ECCENTRIC PIPE REDUCERSTRAINER (STR)STRAINER WITH BLOWDOWN18360039-209352The Professional Engineer's seal and signature apply only to the document to which they are affixed. The Engineer expressly disclaims any responsibility for all other plans, specifications, estimates, reports or other documents or instruments relating to or intended to be used for any part of the engineering project.2017 G&W Engineering Corp.MECHANICAL SUPPLEMENTAL CONDITIONSBEFORE SUBMITTING A PROPOSAL, THE MECHANICAL CONTRACTOR SHALL VISIT THE SITE OF WORK AND FAMILIARIZE HIMSELF WITH ALL SITE CONDITIONS. MECHANICAL CONTRACTOR SHALL CAREFULLY EXAMINE ALL CIVIL, ARCHITECTURAL, STRUCTURAL, PLUMBING, MECHANICAL AND ELECTRICAL CONSTRUCTION DOCUMENTS. SUBMISSION OF A BID WILL ACKNOWLEDGE THE MECHANICAL CONTRACTOR HAS VISITED THE SITE AND EXAMINED ALL CONSTRUCTION DOCUMENTS AND BID INSTRUCTIONS. THE MECHANICAL CONTRACTOR'S BID SHALL INCLUDE ALL MECHANICAL WORK IN THE CONSTRUCTION DOCUMENTS, INCLUDING MECHANICAL WORK RELATED TO EQUIPMENT PROVIDED BY OTHERS.MECHANICAL CONTRACTOR SHALL REQUEST CLARIFICATION ON ANY ITEM(S) OF THE CONTRACT DOCUMENTS THAT ARE NOT UNDERSTOOD OR WHERE CONFLICTS MAY EXIST. PRIOR TO SUBMITTING A BID. RFI SHALL BE PRESENTED A MINIMUM OF FIVE (5) WORKING DAYS BEFORE THE BID DATE. OBTAIN THE RFI FORM AT WWW.DOCUMENTS. SUBMISSION OF A BID WILL ACKNOWLEDGE THE MECHANICAL CONTRACTOR UNDERSTANDS THE SCOPE OF WORK, MEANS AND METHODS OF INSTALLATION, EQUIPMENT AND MATERIALS TO BE USED. RFI THAT HAVE NOT BEEN CLARIFIED PRIOR TO BID, WILL BE PROVIDED BY THE MECHANICAL CONTRACTOR, AS DIRECTED BY THE ENGINEER OF RECORD, AND THE MOST STRINGENT MATERIALS, EQUIPMENT, AND SCOPE OF WORK SHALL APPLY. NO ADDITIONAL COMPENSATION WILL BE MADE FOR THE FAILURE OF THE CONTRACTOR TO OBTAIN CLARIFICATIONS PRIOR TO BID.THE MECHANICAL CONTRACTOR'S BID SHALL BE BASED ON THE SCHEDULED EQUIPMENT, EQUIPMENT, MATERIALS, AND MANUFACTURERS, ARE CONSIDERED SUBSTITUTIONS. CONTRACTOR PROPOSED SUBSTITUTIONS MUST BE SUBMITTED TO THE ENGINEER OF RECORD FOR REVIEW AND WITH A COMPLETED SUBSTITUTION REQUEST FORM. OBTAIN THIS FORM AT WWW.DOCUMENTS. APPROVALS OF SUBSTITUTIONS ARE CONTINGENT UPON ENGINEER'S REVIEW. THE MECHANICAL CONTRACTOR SHALL MAKE NO PRIOR ASSUMPTIONS ON SUBSTITUTIONS NOT APPROVED BY THE ENGINEER. IF THE ENGINEER APPROVES A SUBSTITUTION REQUEST, THE MECHANICAL CONTRACTOR WILL BE HELD RESPONSIBLE FOR ENGINEERING REVISIONS, PHYSICAL SIZE, CAPACITIES, COORDINATION, SUPPLEMENTAL DRAWINGS AND INFORMING OTHER TRADE CONTRACTORS RELATED TO THE INSTALLATION, AS TO ANY SPECIFIED ITEM CHANGES. THE MECHANICAL CONTRACTOR SHALL BEAR AS PART OF HIS CONTRACT, ANY ADDITIONAL COSTS INCURRED IN HIS WORK OR BY THE OTHER CONTRACTORS AS A RESULT OF INSTALLATION FOR OTHER SHOP DRAWINGS SHALL BE SUBMITTED ELECTRONICALLY AS PDF FILES. SHOP DRAWINGS SHALL INCLUDE TRANSMITTAL PAGE(S) INDICATING THE NAME OF THE PROJECT, AND THE NAME, ADDRESS, AND PHONE NUMBER OF THE GENERAL AND MECHANICAL CONTRACTORS. GENERAL CONTRACTOR AND MECHANICAL CONTRACTOR SHALL REVIEW SHOP DRAWING SUBMITTALS FOR COMPLIANCE, CONTENT AND COMPLETENESS AND PROVIDE A STAMP WITH THE DATE OF REVIEW AND SIGNATURE OF THE REVIEWER. TRANSMITTAL PAGE SHALL HAVE INDEX WITH SPECIFICATION SECTION AND DESCRIPTION OF SUBMITTED ITEMS. NO EXCEPTIONS WILL BE TAKEN. SHOP DRAWINGS NOT SUBMITTED IN THIS FORMAT WILL BE REJECTED AND WILL NOT CAUSE REASON FOR PROJECT DELAYS. EQUIPMENT SHALL NOT BE ORDERED UNTIL ENGINEER OF RECORD HAS PROCESSED APPLICABLE SHOP DRAWINGS. A MINIMUM OF SEVEN WORKING DAYS WILL BE ALLOWED FOR SUBMITTAL PROCESSING BY THE ENGINEER. REFER TO PROJECT MANUAL FOR ADDITIONAL REQUIREMENTS.MECHANICAL CONTRACTOR SHALL PERFORM WORK IN A SAFE MANNER. COMPLY WITH APPLICABLE OSHA SAFETY GUIDELINES DURING THE COURSE OF COMPLETING THE WORK DESCRIBED ON THESE CONSTRUCTION DOCUMENTS.SUBMIT AND PAY FOR ALL REQUIRED WORK PERMITS. PROVIDE ALL REQUIRED INSPECTIONS AND RE-INSPECTIONS. PROVIDE A SIGNED CERTIFICATE OF INSPECTION AT THE PROJECT COMPLETION.ALL ITEMS OF WORK AND MATERIALS SHALL BE SPECIFICALLY INSTALLED PER WRITTEN INSTALLATION INSTRUCTIONS AND METHODS OF INSTALLATION AS PROVIDED BY THE MANUFACTURER OF THE EQUIPMENT OR MATERIAL PROVIDER. MECHANICAL CONTRACTOR SHALL UNDERSTAND THE PRODUCT AND METHODS OF INSTALLATION. THE CONTRACTOR SHALL OBTAIN THE INSTALLATION INSTRUCTIONS AND REQUIREMENTS PRIOR TO BID. ALL REQUESTS FOR ADDITIONAL INFORMATION DURING CONSTRUCTION WHERE THE CONTRACTOR HAS NOT PREVIOUSLY OBTAINED THIS INFORMATION FOR BIDDING PURPOSES WILL NOT BE CAUSE FOR ADDITIONAL COSTS OR CONSTRUCTION DELAY.SYSTEMS AS SHOWN ARE DIAGRAMMATIC AND GIVE THE GENERAL ARRANGEMENT ONLY. EXACT LOCATIONS SHALL BE DETERMINED IN THE FIELD ON THE BASIS OF DETAIL DRAWINGS, REVIEWED DRAWINGS, AND SUPPLEMENTARY INFORMATION. INSTALLATION SHALL PROVIDE FOR OPERATING EFFICIENCY, NEATNESS OF APPEARANCE AND EASE OF MAINTENANCE. IT IS EXPECTED THAT THE CONTRACTOR WILL PREPARE DIMENSIONED FIELD ERECTION DRAWINGS AND WORK SKETCHES FOR USE BY THEIR MECHANICS, TO ENSURE PROPER INSTALLATION AND COORDINATION. THE MECHANICAL CONTRACTOR SHALL TAKE THEIR OWN MEASUREMENTS AT THE BUILDING, AND BE RESPONSIBLE FOR THE CORRECT INTERPRETATION AND USE OF ALL SIZES AND DIMENSIONS.CAST IRON NO-HUB, COPPER OR BLACK IRON PIPE IS REQUIRED ABOVE CEILINGS OR IN CAVITIES USED AS A RETURN AIR PLENUM; NO PVC PIPING WILL BE ALLOWED IN RETURN AIR PLENUM SPACES. REFER TO ARCHITECTURAL, MECHANICAL OR PLUMBING DRAWINGS OR VERIFY AT SITE, ALL RETURN AIR PLENUM LOCATIONS.10. M G FURNISH TO THE OWNER OR TENANT A RECORD SET OF LEGIBLE BLACK LINE PRINTS AND AN ELECTRONIC COPY OF THESE DOCUMENTS AT THE PROJECT COMPLETION.ALL MECHANICAL WORK SHALL BE DONE UNDER THE SUPERVISION OF THE MECHANICAL CONTRACTOR, WHO SHALL PROVIDE A COMPETENT AND SKILLED FOREMAN TO LAYOUT ALL WORK. ALL WORK SHALL BE PROVIDED WITH DUE REGARD FOR THE SPACE REQUIREMENTS OF THE OTHER CONTRACTORS. THE MECHANICAL CONTRACTOR SHALL REPORT ANY CONFLICTS OR DIFFICULTIES IN REGARD TO THE INSTALLATION IMMEDIATELY TO THE GENERAL CONTRACTOR OR CONSTRUCTION MANAGER. WHERE CROWDED LOCATIONS EXIST, OR WHERE THERE IS A POSSIBILITY OF CONFLICT BETWEEN TRADES, THE MECHANICAL CONTRACTOR SHALL MAKE COMPOSITE SUPPLEMENTARY DRAWINGS SHOWING THE EXACT LOCATIONS OF PIPES, CONDUIT, DUCTS AND EQUIPMENT. DRAWINGS SHALL BE BASED ON FIELD MEASUREMENTS AND, AFTER CONSULTATION AND AGREEMENT AMONG THE TRADES, THE GENERAL CONTRACTOR OR CONSTRUCTION MANAGER SHALL DIRECT THE SOLUTION BEFORE INSTALLATION OF THE WORK.PROVIDE FIRE STOP AT EACH RATED WALL, FLOOR, ROOF AND CEILING ASSEMBLY A COMPLIANCE WITH THE MANUFACTURER'S APPLICATION DETAILS AND INSTRUCTIONS. PROVIDE TAGGED CERTIFICATIONS AT EACH PENETRATION. PROVIDE SHOP DRAWINGS FOR REVIEW WITH THE U.L. LISTING AND TEST CRITERIA. PROVIDE FIRE STOPPING WHERE REQUIRED BY THE AUTHORITY HAVING JURISDICTION. EQUAL SYSTEMS AS MANUFACTURED J SYSTEMS SPECIFICATIONS.MECHANICAL SUPPLEMENTAL CONDITIONS (CONT.)This electronic drawing file is released under the authority of KEVIN S. GRIESEMER, Missouri License # PE-23628 who maintains the original file and who's registration expires on December 31, 2018. This electronic drawing file may be used as a background drawing. Pursuant to State of Missouri Regulations of the Missouri Board for Architects, Professional Engineers, Professional Land Surveyors, and Landscape Architects, the user of this electronic drawing file agrees to assume all responsibility for any modification to or use of this drawing file that is inconsistent with the requirements of the Rules and Regulations of the Missouri Code of State Regulations Title 4, Division 30. No person may make any modifications to this electronic drawing file without the Engineers express written permission.MECHANICAL SYMBOL LISTSUPPLY AIR DUCT UP SUPPLY AIR DUCT DOWN RETURN AIR DUCT UP RETURN AIR DUCT DOWN EXHAUST AIR DUCT UP EXHAUST AIR DUCT DOWN CHANGE IN DUCT SIZETURNING VANESFLEXIBLE DUCT CONNECTION HORIZONTAL LIFE SAFETY DAMPER VERTICAL LIFE SAFETY DAMPERMMOTORIZED AUTOMATIC DAMPER (MAD) MANUAL DAMPERFCARBON DIOXIDE DETECTORCO 2FCARBON MONOXIDE DETECTORCOHHUMIDISTATMMANOMETERPSPRESSURE SWITCHFRETURN AIR SMOKE DETECTORFREFRIGERANT (Rxxx) DETECTORREFRREFRIGERANT LEAK HORN-STROBETTHERMOSTATPIPE/DUCT IN ATTICPIPE/DUCT BELOW FLOOR OR GRADEPIPE/DUCT ABOVE CEILINGEEXPOSED DUCT, W/ MILL PHOSPHATIZED FINISH RPIPE/DUCT ON ROOFNEW CONNECTION TO EXISTING (VERIFY SIZEAND LOCATION IN FIELD PRIOR TO BID)NNEW BRANCH DUCT TAP & CONNECTION TO EXISTING#DUCT INSULATION (SEE SCHEDULE)XX XX XXPLAN NOTE SYMBOLXREVISION SYMBOLXXEQUIPMENT CALLOUT (SEE SCHEDULE)XX XXGRILLE/DIFFUSER CALLOUT (SEE SCHEDULE)XXXXLIFE SAFETY DAMPER CALLOUT (SEE SCHEDULE) EXISTING DUCT TO REMAINEXISTING TO BE DEMOLISHEDMECHANICAL PIPINGACOMPRESSED AIR LINE CDCONDENSATE DRAIN CDCONDENSATE DRAIN BELOW FLOOR OR GRADE CRCONDENSER WATER RETURN CSCONDENSER WATER SUPPLYCHRCHILLED & HOT WATER RETURN CHSCHILLED & HOT WATER SUPPLYCWRCHILLED WATER RETURN CWSCHILLED WATER SUPPLY DDRAIN LINEGGAS LINE HGHOT GAS LINEHPWRHEAT PUMP WATER RETURN HPWSHEAT PUMP WATER SUPPLYHPCHIGH PRESSURE CONDENSATE HWRHOT WATER RETURN HPSHIGH PRESSURE STEAM HWSHOT WATER SUPPLYLPCLOW PRESSURE CONDENSATELPGLIQUIFIED PETROLEUM GAS (PROPANE) LPSLOW PRESSURE STEAMMPCMEDIUM PRESSURE CONDENSATE MPSMEDIUM PRESSURE STEAMMUWMAKE-UP WATERRLREFRIGERANT LIQUID LINE RSREFRIGERANT SUCTION LINE XX TYPE XX EXISTING PIPE TO BE REMOVED TYPEEXISTING PIPE TO BE REMOVED TYPE (E)EXISTING PIPING2017-0214.00PROVIDE DUCT OR PIPING ASSEMBLY PENETRATIONS OF NON-RATED ASSEMBLIES WITHDRAFT STOPPING, OR SMOKE BARRIER SEALANT SYSTEMS. THROUGH PENETRATION SEALANT MANUFACTURER'S APPLICATION DETAILS AND INSTRUCTIONS. PROVIDE DRAFT STOPPING OR SMOKE BARRIER SEALANTS TO MEET APPROVAL OF THE AUTHORITY HAVING JURISDICTION. 19210273333573128649171464931286491749552212864917-28021HVAC WORK SHALL COMPLY WITH THE LOCAL ADOPTED MECHANICAL CODE AS WELL AS GOVERNING STATE LAW AND LOCAL ORDINANCES. ALL NEW MECHANICAL EQUIPMENT, DUCTWORK AND PIPING SHALL BE ANCHORED AND SEISMICALLY RESTRAINED WHERE REQUIRED TO COMPLY WITH THE 2009 INTERNATIONAL MECHANICAL CODE. PROVIDE ENGINEERED SEISMIC RESTRAINT DETAILS SIGNED AND SEALED BY A MISSOURI LICENSED ENGINEER. SUBMIT FOR REVIEW BY ENGINEER OF RECORD.12864917207922HVAC UPGRADES TOKIPP: INSPIRE ACADEMYMIDDLE SCHOOL1212 N. 22ND STREET ST. LOUIS, MO 63106MECHANICAL CONTRACTOR SHALL CUT AND PATCH ROOF, FLOORS, WALLS, AND CEILINGS WHERE REQUIRED TO INSTALL NEW MECHANICAL DUCT AND PIPING SYSTEMS. SURFACES SHALL BE PATCHED AND LEFT READY FOR FINAL SCHEDULED FINISH. ROOFING REPAIRS SHALL MAINTAIN THE ROOF WARRANTY AND BE PERFORMED BY A QUALIFIED ROOFING CONTRACTOR WHICH MAINTAINS THE WARRANTY OF THE ROOF.MECHANICAL CONTRACTOR SHALL PROVIDE ALL TEMPERATURE CONTROL WIRING, INCLUSIVE A UNLESS NOTED OTHERWISE. TYPICAL SPACE THERMOSTAT OR SENSOR MOUNTING HEIGHT1285933246341212864917640719 FC ARCHITECTURAL FLOOR AND FURNITURE PLANS. DO NOT MOUNT THERMOSTATS OR SENSORS IN DIRECT SUNLIGHT, NEAR HEAT SOURCES, OR ON EXTERIOR WALLS. IF THERMOSTAT MUST BE MOUNTED ON AN EXTERIOR WALL, PROVIDE INSULATED MOUNTING BASE. ALL SYSTEMS SHALL BE COMPLETE INCLUDING, BUT NOT LIMITED TO: EXPERTISE, DESIGN, EQUIPMENT, CABINETS, BOXES, RELAYS, SWITCHES, CONTACTORS, TRANSFORMERS, WIRING, RACEWAYS, AND ELECTRICAL ACCESSORIES. WIRING EXPOSED IN RETURN AIR PLENUM SHALL BE PLENUM RATED CABLE. PROVIDE SHOP DRAWINGS FOR REVIEW AND PROCESSING. THE SHOP DRAWINGS SHALL CONTAIN A FLOOR PLAN WITH THERMOSTAT LOCATIONS, CONTROL SEQUENCE STATEMENT, AND WIRING DIAGRAM WITH ALL PARTS INDICATED OR A BILL OF MATERIAL.12814657651126THE MECHANICAL CONTRACTOR SHALL DISCONNECT AND REMOVE ALL EXISTING MECHANICAL EQUIPMENT OCCURRING IN DEMOLISHED WALLS, FLOORS, ATTICS AND CEILING AREAS. REFER TO THE ARCHITECTURAL DRAWINGS FOR THE COMPLETE SCOPE OF DEMOLITION. DISCONNECT AND REMOVE MECHANICAL EQUIPMENT OCCURRING IN THESE AREAS OR AS OTHERWISE DESCRIBED HEREIN. MECHANICAL COMPONENTS INCLUDING MOTORS, TEMPERATURE CONTROL DEVICES, DIFFUSERS, GRILLES, DAMPERS, PIPING, DUCTWORK, ETC., NOT TO BE RETAINED BY THE OWNER, INCLUDING PIPING, FITTINGS, HANGERS, BRACKETS, INSULATION, ETC., MUST BE REMOVED FROM THE PREMISES, TO BE LEGALLY DISPOSED OF BY THE MECHANICAL CONTRACTOR. ALL LOOSE ENDS OF SYSTEMS WHERE SUCH ABANDONMENT HAS TERMINATED SHALL BE TRIMMED CLEAR AND APPROPRIATELY CAPPED OR SEALED IN A SAFE AND SECURE MANNER. REMOVAL AND DEMOLITION SHALL BE BY THE RESPECTIVE OR APPROPRIATE TRADES. MAINTAIN BRANCH CIRCUIT CONTINUITY TO ADJOINING AREAS AS NEEDED, THIS INCLUDES BUT IS NOT LIMITED TO REMOVAL, MODIFICATION AND REINSTALLATION OF EQUIPMENT AS NEEDED TO SUSTAIN THE EXISTING WORKING CONDITION OF ALL MECHANICAL EQUIPMENT AND TO RETURN THESE AREAS TO FULL WORKING ORDER AT PROJECT COMPLETION. THIS CONTRACTOR SHALL CONFINE HIS ACTIVITIES TO THE AREA SET ASIDE FOR HIM TO DO HIS WORK AND SHALL NOT INTERFERE WITH ANY OF THE OWNER'S ACTIVITIES. THIS CONTRACTOR WILL NOT BE PERMITTED TO STORE MATERIAL EXCEPT WITHIN THE AREAS AS DIRECTED BY THE GENERAL CONTRACTOR. SHOULD ANY DISTURBANCE OF EXISTING INSTALLATION BE NECESSARY, THE CONTRACTOR SHALL SO INFORM THE OWNER WELL IN ADVANCE OF THE TIME CONTEMPLATED FOR THE DISTURBANCE. AFTER A PLAN ACCEPTABLE TO THE OWNER HAS BEEN FORMULATED, THE GENERAL CONTRACTOR SHALL KEEP IN CLOSE PERSONAL CONTACT WITH THE WORK TO SEE THAT IT IS EXECUTED IN ACCORDANCE WITH THE AGREED PROCEDURE.SEALCONTINUITY OF ALL BUILDING SERVICES AND UTILITIES SERVING FACILITIES IN THE BUILDING SHALL BE MAINTAINED WITHOUT INTERRUPTION, EXCEPT FOR SUCH A PERIOD OF TIME DESIGNATED BY THE GENERAL CONTRACTOR. THIS CONTRACTOR SHALL SO ARRANGE AND EXECUTE HIS WORK THAT ANY CONNECTIONS, EITHER TEMPORARY OR PERMANENT, OR REARRANGEMENT OF PRESENT EQUIPMENT, FITTINGS, PIPING, ETC., SHALL BE IN SUCH A MANNER AS TO ASSURE FULL RESUMPTION OF SERVICE AT THE TIME DESIGNATED BY THE GENERAL CONTRACTOR. IF TEMPORARY CROSS CONNECTIONS, FITTINGS, PIPING, ETC., ARE NECESSARY TO ASSURE THIS CONTINUITY OF THE BUILDING SERVICE, THIS CONTRACTOR AT NO ADDITIONAL COST SHALL PROVIDE THEM TO THE GENERAL CONTRACTOR. WHERE USED IN THESE DOCUMENTS, MAINTAIN IS DEFINED AS FOLLOWS: SUSTAIN THE EXISTING WORKING CONDITION OF MECHANICAL DEVICES AND EQUIPMENT WHICH INCLUDES BUT IS NOT LIMITED TO REVISING, REMOVING AND REINSTALLING TO EXECUTE THE NEW WORK INDICATED. THIS BUILDING WILL BE RENOVATED IN PHASES, PROVIDE ALL NECESSARY CROSS CONNECTIONS AND TEMPORARY CONNECTIONS REQUIRED TO PERFORM THE CONSTRUCTION AS DETERMINED BY THE GENERAL CONTRACTOR.REVISIONSJOB NO:2017-0214.00DRAWN BY:J.R.A.CHECKED BY:J.R.A.DATE:09-25-2017SHEET NO.MECHANICAL TITLE SHEETTHE MECHANICAL CONTRACTOR SHALL PROTECT ALL DUCT SYSTEMS, PIPING AND MECHANICAL EQUIPMENT, NEW AND EXISTING, EXPOSED TO CONSTRUCTION, FROM CONSTRUCTION DIRT. PROTECT EACH RETURN AIR DUCT OPENING OF MECHANICAL EQUIPMENT OPERATED DURING CONSTRUCTION WITH MERV 8 FILTERS AND INSTALL MERV 8 FILTER(S) IN EQUIPMENT FILTER RACK. UPON COMPLETION OF CONSTRUCTION, REMOVE RETURN DUCT FILTERS AND REPLACE EQUIPMENT FILTERS WITH NEW FILTERS AS SPECIFIED.THE LANDLORD'S CONSTRUCTION CRITERIA, LEASE AGREEMENT, AND CONSTRUCTION STANDARDS IS HERE-IN MADE PART OF THIS CONTRACT. ALL REQUIREMENTS IN THE LANDLORDS CONSTRUCTION CRITERIA, LEASE AGREEMENT, AND CONSTRUCTION STANDARDS REFERRED TO AS TENANT WORK IS DEFINED AS DIVISION 15 OR 23 MECANICAL WORK AND IS TO BE PROVIDED BY THE MECHANICAL WORK CONTRACTOR. IT IS THE RESPONSIBILITY OF THE MECHANICAL WORK CONTRACTOR TO OBTAIN COPIES OF THESE DOCUMENTS AND COMPLETELY FAMILIARIZE HIMSELF WITH THESE DOCUMENTS PRIOR TO BIDDING THIS PROJECT. SUBMISSION OF A BID ACKNOWLEDGES THE MECHANICAL WORK CONTRACTOR HAS COMPLIED WITH THIS REQUIREMENT OF THE CONTRACT.MECHANICAL ABBREVIATIONSAFF AHJ AHU A.I.P. AL ALT AP AS ATC ATR ATU AV BB BDD BES BFF BMS BOD BOE BOP BS CH CLG CO CO2 CR CRAC CRCU CS CSST CT CU CUH DDC DIFF DISC DLSS DN DPS (E) EA EBB EC EF EG EMS EQPT ER ERV ET EUH EWC EWH EXH FA FAAP FACP FC FCU FD FPC FRT FSC FSD FSEC FTU FV GC GF GWH HP HP HRCUHWCP HX IAH IOM IDIR IV KEFLLSV LV LPG MAX MC MCA MCC MD MIN MH MOCP MTD MUA MUW NC NIC NO OA OD OX PC PCF PSG PT PVC RA RAH RF RG RLRR RTD RTU RV SA SD SF SG SMS SS SSF TA TEMP TOD TOP TXV TYP UH UON UNV UTR VAV VFD VRF VRV VSDW/ WP WSHP XFMRABOVE FINISHED FLOOR AUTHORITY HAVING JURISDICTION AIR HANDLING UNITABANDON IN PLACE ALUMINUM ALTERNATE ACCESS PANELAIR SEPARATORAUTOMATIC TEMPERATURE CONTROL VALVE ALL THREAD RODAIR TERMINAL UNIT MANUAL AIR VENT BASEBOARD HEATER BACK DRAFT DAMPERBANKING EQUIPMENT SUPPLIER BELOW FINISHED FLOOR BUILDING MANAGEMENT SYSTEM BOTTOM OF DUCTBOTTOM OF EQUIPMENT BOTTOM OF PIPEBRANCH SELECTOR - DAIKIN CHILLERCEILINGCARBON MONOXIDE CARBON DIOXIDECONDENSER WATER RETURN COMPUTER ROOM AIR CONDITIONER COMPUTER ROOM CONDENSING UNIT CONDENSER WATER SUPPLY CORRUGATED STAINLESS STEEL TUBING COOLING TOWERCONDENSING UNIT CABINET UNIT HEATER DIRECT DIGITAL CONTROL DIFFUSERDISCONNECTDUCTLESS SPLIT SYSTEM DOWNDIFFERENTIAL PRESSURE SWITCH EXISTINGEXHAUST AIR ELECTRIC BASE BOARDELECTRICAL WORK CONTRACTOR EXHAUST FANEXHAUST GRILLEENERGY MANAGEMENT SYSTEM EQUIPMENTEXHAUST REGISTERENERGY RECOVERY VENTILATOR EXPANSION TANKELECTRIC UNIT HEATER ELECTRIC WATER COOLER ELECTRIC WATER HEATER EXHAUSTFIRE ALARMFIRE ALARM ANNUNCIATOR PANEL FIRE ALARM CONTROL PANEL FLEX CONNECTIONFAN COIL UNIT FIRE DAMPERFIRE PROTECTION CONTRACTOR FIRE-RETARDANT-TREATED FOOD SERVICE CONSULTANT FIRE/SMOKE DAMPERFOOD SERVICE EQPT. CONTRACTOR FAN TERMINAL UNITFIELD VERIFYGENERAL WORK CONTRACTOR GAS FURNACEGAS WATER HEATER HEAT PUMP HORSEPOWERHEAT RECOVERY CONDENSING UNIT HOT WATER CIRC. PUMPHEAT EXCHANGER INTAKE AIR HOODINSTALLATION & OPERATION MANUAL INSIDE DIAMETERINFRA-RED TUBE HEATER (GAS) INTAKE VENTILATORKITCHEN EXHAUST FAN LIQUID LINE SOLENOID VALVE LOUVERLIQUIFIED PETROLEUM GAS (PROPANE) MAXIMUMMECHANICAL WORK CONTRACTOR MINIMUM CIRCUIT AMPERES MOTOR CONTROL CENTER MANUAL DAMPERMINIMUM MOUNTING HEIGHTMAXIMUM OVER CURRENT PROTECTION MOUNTEDMAKE-UP AIR MAKE UP WATERNORMALLY CLOSED NOT IN CONTRACT NORMALLY OPEN OUTDOOR AIR OUTSIDE DIAMETER OXYGENPLUMBING WORK CONTRACTOR POUNDS/CUBIC FOOTPUMP SUCTION GUIDE PRESSURE TREATED POLYVINYL CHLORIDE RETURN AIRRELIEF AIR HOOD RETURN FAN RETURN GRILLEEXISTING DEVICE RELOCATED RETURN REGISTERRESISTANCE TEMPERATURE DETECTOR ROOF TOP UNITRELIEF VENTILATOR SUPPLY AIR SPLITTER DAMPER SUPPLY FAN SUPPLY GRILLESHEET METAL SCREW STAINLESS STEEL SIDE STREAM FILTER TRANSFER AIR TEMPORARYTOP OF DUCT TOP OF PIPETHERMAL EXPANSION VALVE TYPICALUNIT HEATERUNLESS OTHERWISE NOTED UNIVERSALUP THROUGH ROOF VARIABLE AIR VOLUME VARIABLE FREQUENCY DRIVEVARIABLE REFRIGERANT FLOW VARIABLE REFRIGERANT VOLUME VARIABLE SPEED DRIVEWITH WEATHERPROOFWATER SOURCE HEAT PUMP TRANSFORMER 183600392315074192102733740510760294875128217602948782694796594307843701This electronic drawing file is released under the authority of KEVIN S. GRIESEMER, Missouri License # PE-23628 who maintains the original file and who's registration expires on December 31, 2018. This electronic drawing file may be used as a background drawing. Pursuant to State of Missouri Regulations of the Missouri Board for Architects, Professional Engineers, Professional Land Surveyors, and Landscape Architects, the user of this electronic drawing file agrees to assume all responsibility for any modification to or use of this drawing file that is inconsistent with the requirements of the Rules and Regulations of the Missouri Code of State Regulations Title 4, Division 30. No person may make any modifications to this electronic drawing file without the Engineers express written permission.The Professional Engineer's seal and signature apply only to the document to which they are affixed. The Engineer expressly disclaims any responsibility for all other plans, specifications, estimates, reports or other documents or instruments relating to or intended to be used for any part of the engineering project.2017 G&W Engineering Corp.2017-0214.00AIR HANDLING UNIT SCHEDULE*DAIKINPLAN MARKMODEL* NUMBERSUPPLY AIRFLOWOUTSIDE AIRDX COOLING COILSTEAM HEAT COILELECTRICALNOTESCFMESP.FAN HPSUMMERWINTERO/AMODEL NO.TOT MBHSEN MBHENTERING M.A.T.UNIT LEAVINGMODEL NO.TOTAL MBHEAT/LATSTEAM PRESSUREPSIV/P/HZMCA/MOCPDBWBDBWBCFMDBWBDBWBAHU-1CAH017GDGC87502.01095.075.02.00.018005EJ1206B359.1240.080.067.054.953.65JA0601B337.055.0/90.25.0208/3/60-1AHU-2CAH012GDAC52501.0595.075.02.00.09005EJ0906B216.1142.680.067.055.153.65JA0601B219.755.0/93.35.0208/3/60-2NOTES:1. PROVIDE HORIZONTAL AIR HANDLING UNIT VFD CONTROL, DX COILING COIL, STEAM HEAT COIL, MIXING BOX, MERV 8 PLEATED FILTERS, STAINLESS STEEL DRAIN PAN, INSULATED UNIT CABINET, FUSED DISCONNECT SWITCH, CO2 BASED DEMAND VENTILATION, GLOBAL PLASMA SOLUTIONS (GPS) PLASMA AIR PURIFICATION SYSTEM, DDC SPACE SENSOR WITH SETPOINT ADJUSTMENT & TENANT OVERRIDE, AND FIELD INSTALLED JOHNSON CONTROLS.2. PROVIDE STACKED/VERTICAL AIR HANDLING UNIT VFD CONTROL, DX COILING COIL, STEAM HEAT COIL, MIXING BOX, MERV 8 PLEATED FILTERS, STAINLESS STEEL DRAIN PAN, INSULATED UNIT CABINET, FUSED DISCONNECT SWITCH, CO2 BASED DEMAND VENTILATION, GLOBAL PLASMA SOLUTIONS (GPS) PLASMA AIR PURIFICATION SYSTEM, DDC SPACE SENSOR WITH SETPOINT ADJUSTMENT & TENANT OVERRIDE, AND FIELD INSTALLED JOHNSON CONTROLS.MECHANICAL PIPE & PIPE INSULATION SPECIFICATION SCHEDULE(NOT ALL SYSTEMS MAY BE REQUIRED ON THIS PROJECT)PIPE MATERIALSCHEDULE 40 BLACK STEEL, TYPE E OR S, GRADE B ASTM A53/A53M - MALLEABLE IRON THREADED FITTINGS ASTM B16.3, CLASS 150, STANDARD PATTERNSEAMLESS DRAWN COPPER TYPE "L-ACR" ASTM B280, WROUGHT COPPER FITTINGS ASME B16.22, ASME B16.50, BRAZE PER AWS A5.8/A5.8M; ASTM B32 SOLDER 95-5 OR ALLOY HB.SEAMLESS ANNEALED COPPER TYPE "L-ACR" ASTM B280, WROUGHT COPPER FITTINGS ASME B16.22, ASME B16.50, BRAZE PER AWS A5.8/A5.8M; ASTM B32 SOLDER 95-5 OR ALLOY HB.DRAWN COPPER DWV TUBE, ASTM B306, CAST COPPER FITTINGS ASME B16.18, OR WROUGHT COPPER ASME B16.22, SOLDER: ASTM B 32 LEAD FREE WITH ASTM B 813 WATER-FLUSHBLE FLUX.SOLID WALL PVC SCHEDULE 40 , ASTM D 2665 DWV, PVC FITTINGS: ASTM D 2665 MADE TO ASTM 3311 DWV, PRIMER: ASTM F 656, SOLVENT: ASTM D 2564PIPE INSULATIONPIPE DIAMETER: ALL1/2" THICK, NOTE 1 (WITH VAPOR BARRIER) OR NOTE 2 (NO VAPOR BARRIER)PIPE DIAMETER < 1.5" 1-1/2" THICK, NOTE 2.3PIPE DIAMETER > 1.5" 1-1/2" THICK, NOTE 2.3NOTES: 1. INORGANIC GLASS FIBER WITH ASJ2. CLOSED CELL ELASTOMERIC3. INSULATE REFRIGERANT PIPE PER F- A7 )F15PCF P =K1P K /1 7F K) A F F0KF- AF )F15PCF P = K1P K /1 7F K) FEQUIPMENT MANUFACTURER'S ASTM C 547; TYPE I, TYPE IVPERM-INI.O.M. COAT INSULATION ONASTM: C 585, C 795ASTM C 534, TYPE I - TUBULAR GRADEBUILDING EXTERIOR WITH 2 ASTM C 1136 (JACKETS); TYPE I, II, III, IV, VIIIASTM E 84COATS OF ARMAFLEX TYPE WBASTM: C 665, C 1617, C 1338ASTM G-21/C 1338FINISH, UV, OZONE, & MOISTUREASTM: C 1104, C 356ASTM G-22RESISTANT COMPOUND.GREENGUARD CERTIFICATIONASTM D 1056, 2B1GREENGUARD CHILDREN & SCHOOLSNFPA 255CERTIFICATIONNFPA 90A & 90BNFPA 90A & 90BUL 723UL CLASSIFIEDUL 181GREENGUARD CERTIFICATION GREENGUARD CHILDREN & SCHOOLS CERTIFICATIONPIPE INSTALLATION:CONDENSATE PIPE:1. PROVIDE MINIMUM 1 % SLOPE IN DIRECTION OF FLOW.REFRIGERANT PIPE:PROVIDE LIQUID LINE SIGHT GLASS AND DRYER-STRAINER AS MANUFACTURED BY SPORLAN OR EQUAL.INSTALL REFRIGERANT PIPING IN COMPLIANCE WITH ASHRAE 15, "SAFETY CODE FOR REFRIGERATION SYSTEMS."COMPLY WITH ASME B31.5, "REFRIGERATION PIPING AND HEAT TRANSFER COMPONENTS."CONSTRUCT SOLDERED JOINTS ACCORDING TO ASTM B 828 OR COPPER DEVELOPMENT ASSOCIATION'S "COPPER TUBE HANDBOOK."CONSTRUCT BRAZED JOINTS ACCORDING TO AMERICAN WELDING SOCIETY'S "BRAZING HANDBOOK," CHAPTER "PIPE AND TUBE."USE TYPE BCuP, COPPER-PHOSPHORUS ALLOY FOR JOINING COPPER SOCKET FITTINGS WITH COPPER PIPE.USE TYPE BAg, CADMIUM-FREE SILVER ALLOY FOR JOINING COPPER WITH BRONZE OR STEEL.TESTS AND INSPECTIONS IN COMPLIANCE WITH ASME B31.5, CHAPTER VI.ROOFTOP UNIT SCHEDULE (ALTERNATE BID #1)*DAIKINPLAN MARKMODEL* NUMBEREERSUPPLY AIRFLOWOUTSIDE AIRDX COOLING COILUNIT IEER DATAELECTRICALWEIGHT (LB)NOTESCFMESP.FAN HPSUMMERWINTERO/ATOT MBHSEN MBHENTERING M.A.T.UNIT LEAVINGV/P/HZMCA/MOCPDBWBDBWBCFMDBWBDBWBRTU-1MPS020G1070001.07.595.075.02.00.0900249.1196.277.663.854.152.212.5208/3/60116.3/15034751NOTES: 1. PROVIDE VAV UNIT WITH VFD AND DUCT PRESSURE CONTROL, 0-100% ECONOMIZER WITH DRY BULB CONTROL, BAROMETRIC RELIEF TO BE FIELD INSTALLED IN RETURN DUCT, HORIZONTAL SUPPLY AND RETURN DUCT DISCHARGE, MERV 8 PLEATED FILTERS, STAINLESS STEEL DRIP PAN, INSULATED UNIT CABINET, NON-FUSED DISCONNECT SWITCH, FIELD POWERED SERVICE RECEPTACLE, PHASE FAILURE MONITOR, CO2 BASED DEMAND VENTILATION, GLOBAL PLASMA SOLUTIONS (GPS) PLASMA AIR PURIFICATION SYSTEM, FIELD INSTALLED JOHNSTON CONTROLS, DDC SPACE SENSOR WITH SETPOINT ADJUSTMENT & TENANT OVERRIDE, AND EQUIPMENT CURB.CONDENSING UNIT SCHEDULE* DAIKINPLAN MARKMODEL NUMBER *CAP (MBH)EERIEERSST) K AMBIENT) K V/PH/HZMCA/MOCPWEIGHTREFRIG. LINE CONNECTION SIZES (O.D.)NOTESSUCTIONLIQUIDHOT GASCU-1RCS025D279.311.013.644.095.0208/3/60125.9/1751853(2) 1-5/8(2) 7/8(2) 7/81CU-2RCS015D182.812.313.044.095.0208/3/6071.9/901821(2) 1-1/8(2) 5/8(2) 7/81NOTES: 1. PROVIDE AIR COOLED CONDENSING UNIT WITH MOUNTING RAILS, BUILT IN HAIL PROTECTION, HOT GAS BYPASS, SINGLE POWER BLOCK FIELD CONNECTION, SINGLE THRU DOOR DISCONNECT SWITCH, FIELD POWERED SERVICE RECEPTACLE, AND LOW AMBIENT CONTROL TO 45 DEGREES.HVAC UPGRADES TOKIPP: INSPIRE ACADEMYMIDDLE SCHOOL1212 N. 22ND STREET ST. LOUIS, MO 63106GRILLE, REGISTER, AND DIFFUSER SCHEDULE* TITUSPLAN MARKMODEL NO. *NECK SIZEFACE SIZEMAX CFMP.D.BORDERPATTERNFINISHNOTESSADL30x1532-11/16"x 17"26250.1TYPE 12-WAY#261SBDL25x1527-11/16"x 17"16000.1TYPE 12-WAY#261SCDL20x1222-11/16"x 13-15/16"11000.1TYPE 12-WAY#261RA33RS28" x 56"30"x58"70000.08TYPE 1-#26-NOTES: 1. PROVIDE WITH OPPOSED BLADE BALANCING DAMPER.DUCT INSULATION SCHEDULEID TAGMATERIALK BTU.IN AT 75 F. D IB H.SQ.FT.FFT 3FORMTHICK- NESSR-VALUENO. OF LAYERSFIELD APPLIED JACKETVAPOR RETARDER REQUIRED1MINERAL-FIBER BLANKET (0.26/0.75)N/A1"3.8ONEFOIL & PAPERYES8THERMADUCT (0.15/3.4)N/A1 3 168.1N/ANONEYESGENERAL NOTE: DUCT SIZES INDICATED ON DRAWINGS ARE SHEET METAL SIZE AND INCLUDE LINER SPECIFIED.SEAL18929653-18502819220744-1850281M1.1REVISIONSJOB NO:2017-0214.00DRAWN BY:J.R.A.CHECKED BY:J.R.A.DATE:09-25-2017SHEET NO. MECHANICAL SCHEDULES & DETAILSFENCE DETAILNO SCALE1" NEOPRENE/CORK ISOLATION PAD BY M.C. (4) REQUIREDGALV. SHEETMETAL CAP OVER ROOFING TACKED TO WOOD NAILER"THY-CURB" (4) SEISMIC HOLD-DOWN STRAPS ATTACHED WITH (10) #10 TEK SCREWS (5) EACH SIDE, PROVIDE SHOP DRAWING SUBMISSION.NOTE:ALL ROOF WORK SHALL COMPLY WITH BUILDING STANDARDS AND BE INCLUDED IN MECHANICAL CONTRACTOR'S BID. THIS CONTRACTOR SHALL USE PROPERTY MANAGER APPROVED ROOFING CONTRACTOR AND MAINTAIN ROOF WARRANTIES.WOOD NAILERCONDENSING UNITCONDENSING UNIT1" NEOPRENE ISOLATION PADSEACH CORNERPROVIDE SLACK AS RECOMENDED BY RESTRAINT MANUFACTURER"MICRO METL" TYPE MM475 EQUIPMENT SUPPORT FURNISHED AND INSTALLED BYPIPE & TUBING SUPPORT SPACINGNOMINAL PIPE SIZE (IN.)< 1/21/23/411-1/223456810121416182024MAXIMUM SUPPORT SPACING (FT.)PIPE77791011121416171922232527283032TUBING5678891012131416-------NOTE: FOR TRAPEZE HANGER TAKE SPACING OF SMALLEST SIZE ON TRAPEZE.INSULATION8426657-385427WELDPIPE SADDLEHANGER RODADJUSTABLE, SWIVEL ROLLERHANGER,. SEE SPECSPROVIDE INSULATION SHIELD AND INSERT FOR ALL PIPING, 8" MAXIMUM.9991706-355726The Professional Engineer's seal and signature apply only to the document to which they are affixed. The Engineer expressly disclaims any responsibility for all other plans, specifications, estimates, reports or other documents or instruments relating to or intended to be used for any part of the engineering project.2017 G&W Engineering Corp.2017-0214.00INSULATION BANDROOFING TO BE LAPPED UP SUPPORT UNDER CAPSET CURB(S) ON CONCRETE DECK WITH FIRE TREATEDWOOD BLOCKING TO LEVEL CURB, AND ATTACH CURB(S) TO DECK WITH (6) 3/8" DIA. EXPANSION BOLT WITH WASHERS. (MIN. 4 CORNERS OF CURB)2'-0"HVAC CONTRACTOR. (TYP OF 2) OR"PATE" EQUALROOFINGCONCRETE ROOF DECKADJUSTABLE ROLLER HANGERTYPE 43 IN SPECIFICATIONS 8542535-4701HANGER RODINSULATION (VAPOR BARRIER TYPE REQUIRED FOR LOW TEMP. PIPE).PROVIDE HIGH COMPRESSIVE STRENGTH INSULATION BLOCKS UNDER INSULATION SHIELD.INSULATION SHIELD AT HANGER.ADJUSTABLE CLEVIS HANGER TYPE 1 IN SPECIFICATIONS18570850-230916This electronic drawing file is released under the authority of KEVIN S. GRIESEMER, Missouri License # PE-23628 who maintains the original file and who's registration expires on December 31, 2018. This electronic drawing file may be used as a background drawing. Pursuant to State of Missouri Regulations of the Missouri Board for Architects, Professional Engineers, Professional Land Surveyors, and Landscape Architects, the user of this electronic drawing file agrees to assume all responsibility for any modification to or use of this drawing file that is inconsistent with the requirements of the Rules and Regulations of the Missouri Code of State Regulations Title 4, Division 30. No person may make any modifications to this electronic drawing file without the Engineers express written permission.3/8" DIA. HANGER RODS WITH 36" MAX. SPACING ON EACH.1" 2 GAGE CHANNEL OR2"x2"x|" ANGLE.1" MAX.TRAPEZE HANGER FOR UP TO 1000 lb. UNIFORM LOAD1M1.21088661166929CONDENSING UNIT SUPPORT DETAIL2498741-178158NO SCALE4728341-1397103230306-69904PAIR SPACING:10 FT.8 FT.5 FT.4 FT.DUCT PERIMETER, MAXIMUM HALFSTRAPWIRE/ RODSTRAPWIRE/ RODSTRAPWIRE/ RODSTRAPWIRE/ RODP/2 = 30"IN. x GAIN. x GAIN. x GAIN. x GA1 x 2210 GA(.135")1 x 2210 GA(.135")1 x 2212 GA(.106")1 x 2212 GA(.106")P/2 = 72"1 x 183/8"1 x 201/4"1 x 221/4"1 x 221/4"P/2 = 96"1 x 163/8"1 x 183/8"1 x 203/8"1 x 221/4"P/2 = 120"1.5 x 161/2"1 x 163/8"1 x 183/8"1 x 201/4"P/2 = 168"1.5 x 161/2"1.5 x 161/2"1 x 163/8"1 x 183/8"P/2 = 192"NONE1/2"1.5 x 161/2"1 x 163/8"1 x 163/8"P/2 = 193"+SPECIAL ANALYSIS REQUIREDSINGLE HANGER MAXIMUM ALLOWABLE LOADLAP JOINED STRAPS, MINIMUM FASTENERS (PLACE FASTENERS IN SERIES, NOT SIDE BY SIDE):STRAPWEIGHTWIRE/ RODWEIGHTSTRAP IN. x GAFASTENERS(QTY) - SIZEIN. x GALBS. ( N )LBS.1 x 18, 20, 22(2) - #10 SMS or1 x 222600.10680(1) 1 BO 1 x 203200.1351201 x 16( ) 1 BO 1 x 184200.1621601.5 x 16( ) 1 x 167001/42701.5 x 1611003/86801/212505/820003/43000NOTE: TABLE ALLOWS FOR DUCT WEIGHT, 1 LB./SQ. FT. INSULATION WEIGHT, AND NORMAL REINFORCEMENT AND TRAPEZE WEIGHT.BAR JOIST OR OTHER STRUCTURAL COMPONENT2M1.2PIPE HANGER DETAILS8798025-1502509155431-3657NO SCALEGALVANIZED SHEET METAL STRAPLOAD RATED SHEET METAL SCREW W/WASHER13" POINT68825519958596" TO 144" **7358627-247676FASTEN UNIT TO FRAME WITH MIN 8 - 1/2" DIA. MACHINE BOLTS AND LOCK NUTS13" POINT9'-0"13" POINT48" TO 96" **2'-6"WASHER2'-6"STRAP WASHER NUTSTRUCTURE4228531-26889712" MAX.1 in. MIN.HANGER STRAPS (SEE CHART)60 in. MAX.520441736852420218836852HANGERLOAD RATED FASTENERSBAND OF SAME SIZE AS HANGER STRAPNOT REQUIRED FOR DUCTWORK WITH LESS THAN 6 SQ. FT. CROSS-SECTIONAL AREAUNLESS FOOT OF STRAP IS PLACED UNDER A BOTTOM REINFORCEMENTSCREWS16668945-69509666689451328017091969-69509670919691328011AAPLAN**NOTE:111364090-12926341SIDE VIEW837779480694ALL STEEL MEMBERS TO BE L1-1/2x2/2x3/16 WITH THE EXCEPTION OF FOUR SUPPORT LEGS WHICH AREL2x2x1/4WELD FRAME TOGETHER USING 1/8" FILLET WELD (TYP)PROVIDE ADDITIONAL BRACING FROM TOP OF UNIT TO ROOF OR WALLL2x2x 1 4 " LEG (TYP)DUCTWORK133019031081011255192-157743911255192-95981 3/4"END VIEW6"FLOOR2627183-20388WASHERS MAY BE OMITTED WITH 100 LB MAX LOAD ON 22 GA STRAP WHEN FOLDEDCONTRACTOR SHALL ADJUST DIMENSIONS OF STAND TO ACTUAL FIELD MEASUREMENTS.11727081-594461 8 "SECTION AABASE PLATE 14"x6"x6" FOR CONNECTION TO CONCRETE FLOOR. PROVIDE 1 3 8 KWICKBOLT ANCHOR WITH MIN. 2 " EMBEDMENT, ICBO, 1CBO #462718517798-1004111047171-33775HVAC UPGRADES TOKIPP: INSPIRE ACADEMYMIDDLE SCHOOL1212 N. 22ND STREET ST. LOUIS, MO 63106SEAL8"3M1.2DUCT HANGER DETAILS2327018-1654582719327-4904NO SCALE4M1.2MOUNTING STAND DETAIL8670978-64208264708-173954NO SCALE5M1.2FENCE AND PAD DETAIL14914418-172186NOT TO SCALE13211154-65802STEAM SUPPLY185177982658AIR VENTPRESSURE GAUGEVACUUM BREAKERCONTROL VALVESTRAINERREVISIONSPIPE FULL SIZE OF UNIT DRAIN CONNECTIONREMOVABLE CAPNOTES:9131697-335262LOCATE TRAPS SO AS TO BE ACCESSIBLE FOR CLEANING.INVERTEDUNIONVALVEVALVESTRAINERVALVEMBUCKETSTEAM TRAPREMOVABLE CAP2"HEIGHT SHALL BE EQUAL TO FAN STATIC PRESSURE, PLUS 1".TERMINATE CONDENSATE LINE VIA INDIRECT CONNECTION TO NEAREST: ROOF DRAIN, GUTTER, OR FLOOR DRAIN.DUCTWORKSTEAM COILDRIP LEG 14" MINDIRT LEGVALVECHECK VALVESTRAINERVALVEF&T STEAM TRAPJOB NO: DRAWN BY:2017-0214.00J.R.A.FLOWVERIFY MFR. REQUIREMENT FORMIRO MODEL #6-DS-P ORCHECKED BY:J.R.A. 2" AIR GAPSEE NOTE 2P-TRAP, UNIT MAY CONTAIN INTERNAL TRAP.PROVIDE MINIMUM 2" AIR GAP @ DRAIN TERMINATION#8-DS-P DUCT SUPPORT. INSTALL AT MANUFACTURER RECOMMENDED SPACING.NOTE:PITCH CONDENSATE 1/4" PER FOOT.DIRT LEGDRAIN14199606497383HOSE END CONNECTIONDATE: SHEET NO.09-25-20178493671292103EQUIPMENT CABINETELEVATE DUCT A MINIMUM OF 12" ABOVE GRADE.CONDENSATE RETURN1722499975856COOLING EQUIPMENT CONDENSATE DRAIN TRAP7EXTERIOR DUCT SUPPORT DETAIL8STEAM COIL PIPING DETAILM1.2NO SCALEM1.2NO SCALEM1.2NO SCALEMECHANICAL DETAILS14064183-34710RELIEF LOUVER ABOVE LOWER GYM ROOF# PLAN NOTES - MECHANICAL DEMOLITION8SASA2REMOVE EXISTING AIR HANDLING UNIT, HANGERS/SUPPORTS, INDICATED SUPPLYDUCTWORK, INDICATED RETURN DUCTWORK, PIPING, CONTROLS AND ASSOCIATED COMPONENTS TO MAKE WAY FOR NEW WORK.443226252567848-402784MECHANICAL MEZZANINE924x24200 200 2625 M2.2EXHAUST LOUVER ABOVE LOWER GYM ROOFREMOVE EXISTING RETURN AIR FAN, SUPPORTS, INDICATED DUCTWORK, CONTROLS AND ASSOCIATED COMPONENTS TO MAKE WAY FOR NEW WORKREMOVE SECTION OF CONDENSATE PIPING IN DOORWAY TO ALLOW FOR INSTALLATION OF NEW AHU COMPONENTS.REMOVE DIFFUSERS AND INFILL OPENINGS WITH CMU TO MATCH EXISTING THEN PRIME AND PAINT TO MATCH EXISTING WALL FINISH.11EXISTING KITCHEN EXHAUST SYSTEM SHALL REMAINThe Professional Engineer's seal and signature apply only to the document to which they are affixed. The Engineer expressly disclaims any responsibility for all other plans, specifications, estimates, reports or other documents or instruments relating to or intended to be used for any part of the engineering project.2017 G&W Engineering Corp.EXISTING SUPPLYDUCTWORKCAP EXISTING KITCHEN EXHAUST SYSTEM SHALL REMAINEXISTING OUTDOOR AIR INTAKE18570850-2204121408791622511This electronic drawing file is released under the authority of KEVIN S. GRIESEMER, Missouri License # PE-23628 who maintains the original file and who's registration expires on December 31, 2018. This electronic drawing file may be used as a background drawing. Pursuant to State of Missouri Regulations of the Missouri Board for Architects, Professional Engineers, Professional Land Surveyors, and Landscape Architects, the user of this electronic drawing file agrees to assume all responsibility for any modification to or use of this drawing file that is inconsistent with the requirements of the Rules and Regulations of the Missouri Code of State Regulations Title 4, Division 30. No person may make any modifications to this electronic drawing file without the Engineers express written permission.# PLAN NOTES - MECHANICAL1M2.2EXISTING RETURN DUCTWORK FROM BELOWAHU 12 AHU 2APPROX. 48x66 OA (E)LOUVER ABOVE LOWER CAFETERIA/KITCHEN ROOFPROVIDE STEAM HEATING/ELECTRIC COOLING SPLIT SYSTEM AIR HANDLING UNIT AS SCHEDULED AND SPECIFIED. UNIT SHALL SET DEAD LEVEL ON EQUIPMENT STAND ALLOWING RETURN DUCT TO PASS BENEATH. EXTEND AND RECONNECT EXISTING STEAM AND CONDENSATE PIPING TO NEW UNIT PER PIPING DIAGRAM; MATCH EXISTING SIZE. EXTEND FULL DIAMETER CONDENSATE DRAIN FROM COOLING COIL UNIT CONNECTION, PIPE DOWN INSIDE BUILDING AND SPILL ON GRADE IN GREEN SPACE NEXT TO BUILDING. TERMINATE WITH TURNED DOWN ELBOW. EXTEND REFRIGERANT PIPING THROUGH WALL ABOVE GYM ROOF1APPROX. 22x66 OA (E)7974315-260237917964932052138024576205213NNTHEN EXTEND TO CORRESPONDING CONDENSING UNIT. EXTEND SUPPLY AND RETURN DUCTS FROM FLEXIBLE CONNECTIONS FULL SIZE AT UNIT, AND TRANSITION TO DUCTS SIZED AS SHOWN.PROVIDE STEAM HEATING/ELECTRIC COOLING SPLIT SYSTEM AIR HANDLING UNIT ASMECHANICAL MEZZANINE DEMOLITION PLANSCALE: 1/8" = 1'-0"MECHANICAL MEZZANINE MECHANICAL PLANSCALE: 1/8" = 1'-0"SCHEDULED AND SPECIFIED. UNIT SHALL SET DEAD LEVEL ON EQUIPMENT RAILS. EXTEND AND RECONNECT EXISTING STEAM AND CONDENSATE PIPING TO NEW UNIT PER PIPING DIAGRAM; MATCH EXISTING SIZE. EXTEND FULL DIAMETER CONDENSATE DRAIN FROM COOLING COIL UNIT CONNECTION, PIPE DOWN INSIDE BUILDING AND SPILL ON GRADE IN GREEN SPACE NEXT TO BUILDING. TERMINATE WITH TURNED DOWN ELBOW. EXTEND REFRIGERANT PIPING THROUGH WALL ABOVE GYM ROOF THEN EXTEND TO CORRESPONDING CONDENSING UNIT. EXTEND SUPPLY AND RETURN DUCTS FROM FLEXIBLE CONNECTIONS FULL SIZE AT UNIT, AND TRANSITION TO DUCTS SIZED AS SHOWN. HVAC UPGRADES TOKIPP: INSPIRE ACADEMYMIDDLE SCHOOL1212 N. 22ND STREET ST. LOUIS, MO 63106PROVIDE CONDENSING UNIT AS SCHEDULED AND SPECIFIED. UNIT SHALL SET DEAD LEVEL ON EQUIPMENT CURB RAILS. EXTEND RAILS A MINIMUM OF 6" BEYOND EQUIPMENT ON BOTH SIDES. EXTEND REFRIGERANT PIPING PER MANUFACTURER'S IOM TO ASSOCIATED AIR HANDLING UNIT. COAT REFRIGERANT PIPING INSULATION EXPOSED TO THE ELEMENTS WITH WEATHER PROOF COATING AS SPECIFIED.186560143879ALTERNATE BID #1: PROVIDE ELECTRIC COOLING PACKAGED ROOFTOP UNIT AS SCHEDULED AND SPECIFIED. UNIT SHALL SET DEAD LEVEL ON MINIMUM 14" HIGH FACTORY CURB SET ON EQUIPMENT PAD. PROVIDE ALL SHIMS AND BUILD UP MATERIALS AS REQUIRED FOR A LEVEL INSTALLATION. EXTEND FULL DIAMETER CONDENSATE DRAIN FROM UNIT CONNECTION AND SPILL ON GRADE. EXTEND HORIZONTALLY CONFIGURED SUPPLY AND RETURN DUCTS FROM FLEXIBLE CONNECTIONS FULL SIZE AT UNIT AND TRANSITION TO DUCTS SIZED AS SHOWN.RUN 1 1/4" CONDENSATE FROM AIR HANDLING UNITS DOWN EXTERIOR WALL AND EXIT BUILDING AT 6" ABOVE GRADE. SPILL CONDENSATE ON GRADE.REMOVE GLASS BLOCK AS REQUIRED TO CREATE OPENING FOR DUCTWORK. FRAME OPENING FLUSH WITH INNER AND OUTER SURFACE OF BLOCK THEN COVER WITHPRE-FINISHED SHEET METAL PANELS WITH FEWEST SEAMS POSSIBLE. COLOR SHALL MATCH WINDOW FRAME COLOR. FILL VOID BETWEEN METAL PANELS WITH BATT INSULATION. CALK EDGES AND SEAMS WITH CLEAR SILICONE SEALANT.PROVIDE CONCRETE PAD AND FENCE AS SPECIFIED.PROVIDE NEW OPENING IN BLOCK WALL; PROVIDE LINTEL IF REQUIRED BY STRUCTURAL ENGINEER. INSTALL SHEET METAL TRIM TO TO FINISH OPENING IN WALL AND PAINT TO MATCH WALL.PROVIDE PAINT GRIP FINISH ON INDOOR EXPOSED DUCTWORK. PREP, PRIME AND PAINT INDOOR EXPOSED DUCTWORK. COLOR SELECTION BY OWNER.AUDITORIUMCU 3 1ON ROOF ABOVEGYMCAFETERIACU32ON ROOF ABOVESB 1600SB 1600SB 1600628"0 9728x288SEALSC 1100SC1100RA--RTU 1ON GRADE418517798290968618517798-1248314KITCHEN28x2882M2.2REVISIONSUP TO MEZZANINE5JOB NO:DRAWN BY:2017-0214.00J.R.A.5592538257134NCHECKED BY:J.R.A.PARTIAL FIRST FLOOR MECHANICAL PLANSCALE: 1/8" = 1'-0"DATE: SHEET NO.09-25-20172017-0214.00ENLARGED PLANS - MECHANICALThis electronic drawing file is released under the authority of KEVIN S. GRIESEMER, Missouri License # PE-23628 who maintains the original file and who's registration expires on December 31, 2018. This electronic drawing file may be used as a background drawing. Pursuant to State of Missouri Regulations of the Missouri Board for Architects, Professional Engineers, Professional Land Surveyors, and Landscape Architects, the user of this electronic drawing file agrees to assume all responsibility for any modification to or use of this drawing file that is inconsistent with the requirements of the Rules and Regulations of the Missouri Code of State Regulations Title 4, Division 30. No person may make any modifications to thisThe Professional Engineer's seal and signature apply only to the document to which they are affixed. The Engineer expressly disclaims any responsibility for all other plans, specifications, estimates, reports or other documents or instruments relating to or intended to be used for any part of the engineering project.SHEET NO.ENLARGED PLANS - MECHANICALDATE:09-25-2017CHECKED BY:J.R.A.DRAWN BY:J.R.A.JOB NO: 2017-0214.00REVISIONSHVAC UPGRADES TOKIPP: INSPIRE ACADEMYMIDDLE SCHOOL1212 N. 22ND STREET ST. LOUIS, MO 631062017-0214.001098295010747753593495200753593937769SEALROOFROOFAPPROX. 72x22 RELIEF LOUVER (E)APPROX. 102x14 SA (E)APPROX. 48x66 OA (E)124x24138x301152x16ROOF 1AHU 224x241AHU 1 1 76x161 66x18CAPBAROMETRIC RELIEF DAMPERSA 2625FANFANCOILS (DX/ STEAM)FILTER/ MIXING66x18APPROX. 8x6 SA (E)1152x1666x181191x13FILTER/ MIXINGCOILS (DX/ STEAM)NEW BAROMETRIC RELIEF DAMPER66x18MECHANICAL MEZZANINEMECHANICAL MEZZANINE1SET UNIT ON 4" GALVANIZED STEEL RAILS. SECURE TO FLOOR WITH SIX 3/8" ANCHOR BOLTS AND BOLT UNIT TO RAILS WITH EIGHT 3/8" BOLTS.APPROX. 48x16 RA (E)EQUIPMENT STAND PER DETAILSAPPROX. 90x16 RA (E)APPROX. 91x13 RA (E)COACHES' OFFICEGYMAHU-1 ELEVATIONSCALE: 1/4" = 1'-0"AHU-2 ELEVATIONSCALE: 1/4" = 1'-0"1M2.22M2.2ROOFNOTE:SEAL ALL EXTERIOR WALL PENETRATIONS WEATHER TIGHT.LAY-IN CEILING 8" BEAMSC 1100SC 1100RA--INSTALL DRUM DIFFUSERS ON A 10" DEEP PLENUM ROTATED DOWN FROM HORIZONTALRTU 1EXISTING UNIT VENTILATORFLOORBAROMETRIC RELIEF INSTALLED IN RETURN DUCTGRADEMAINTAIN A MINIMUM OF 6" CLEAR IN FRONT OF AIR INTAKERTU-1 ELEVATION (ALTERNATE BID #1)SCALE: 1/4" = 1'-0"3M2.3electronic drawing file without the Engineers express written permission.2017 G&W Engineering Corp.ELECTRICAL SUPPLEMENTAL CONDITIONSBEFORE SUBMITTING A PROPOSAL, THE ELECTRICAL CONTRACTOR SHALL VISIT THE SITE OF WORK AND FAMILIARIZE THEMSELVES WITH ALL SITE CONDITIONS. ELECTRICAL CONTRACTOR SHALL CAREFULLY EXAMINE THE ENTIRE SET OF CONSTRUCTION DOCUMENTS. SUBMISSION OF A BID WILL ACKNOWLEDGE THE ELECTRICAL CONTRACTOR HAS VISITED THE SITE AND EXAMINED ALL CONSTRUCTION DOCUMENTS AND THE BID INSTRUCTIONS. ALL ELECTRICAL WORK IN THE CONSTRUCTION DOCUMENTS, INCLUDING THAT REQUIRED BY OTHER DIVISIONS, GENERALLY INSTALLED BY THE ELECTRICAL CONTRACTOR, WHERE EQUIPMENT IS FURNISHED BY OTHERS, SHALL BE INCLUDED. IT IS EXPRESSLY UNDERSTOOD THAT THIS PROPOSAL IS BASED ON THE ABOVE REQUIREMENTS AND THAT IT COVERS MATERIAL AND LABOR NECESSARY TO COMPLETE THE SCOPE OF WORK DESCRIBED HEREIN.ELECTRICAL CONTRACTOR SHALL PERFORM WORK IN A SAFE MANNER. COMPLY WITH APPLICABLE OSHA SAFETY GUIDELINES DURING THE COURSE OF PERFORMING THE WORK DESCRIBED IN THESE CONSTRUCTION DOCUMENTS.ELECTRICAL CONTRACTOR SHALL REQUEST CLARIFICATION ON ANY ITEM(S) OF THE CONTRACT DOCUMENTS THAT X P WORKING DAYS BEFORE THE BID DATE. OBTAIN THE RFI FORM AT WWW.DOCUMENTS. SUBMISSION OF A BID WILL ACKNOWLEDGE THE ELECTRICAL CONTRACTOR UNDERSTANDS THE SCOPE OF WORK, MEANS AND METHODS OF INSTALLATION, EQUIPMENT AND MATERIALS TO BE USED. RFI THAT HAVE NOT BEEN CLARIFIED PRIOR TO BID WILL BE PROVIDED BY THE ELECTRICAL CONTRACTOR, AS DIRECTED BY THE ENGINEER OF RECORD, AND THE MOST STRINGENT MATERIALS, EQUIPMENT, AND SCOPE OF WORK SHALL APPLY. NO ADDITIONAL COMPENSATION WILL BE MADE FOR THE FAILURE OF THE CONTRACTOR TO OBTAIN CLARIFICATIONS PRIOR TO BID.4. L MANUFACTURERS ARE CONSIDERED SUBSTITUTIONS. CONTRACTOR PROPOSED SUBSTITUTIONS MUST BE SUBMITTED TO THE ENGINEER OF RECORD FOR REVIEW WITH A COMPLETED SUBSTITUTION REQUEST FORM. OBTAIN THIS FORM AT WWW.DOCUMENTS. APPROVALS OF SUBSTITUTIONS ARE L K SUBSTITUTIONS NOT APPROVED BY THE ENGINEER. IF THE ENGINEER APPROVES A SUBSTITUTION REQUEST, THE ELECTRICAL CONTRACTOR WILL BE HELD RESPONSIBLE FOR ENGINEERING REVISIONS, PHYSICAL SIZE, CAPACITIES, COORDINATION, SUPPLEMENTAL DRAWINGS AND INFORMING OTHER TRADE CONTRACTORS AS TO ANY SPECIFIED ITEM CHANGES RELATED TO THE INSTALLATION. THE ELECTRICAL CONTRACTOR SHALL BEAR AS PART OF THEIR CONTRACT, ANY ADDITIONAL COSTS INCURRED IN THEIR WORK, OR BY THE OTHER CONTRACTORS, SHOP DRAWINGS SHALL BE SUBMITTED ELECTRONICALLY AS PDF FILES. SHOP DRAWINGS SHALL INCLUDE TRANSMITTAL PAGE(S) INDICATING THE NAME OF THE PROJECT, AND THE NAME, ADDRESS, AND PHONE NUMBER OF THE GENERAL AND ELECTRICAL CONTRACTORS. GENERAL CONTRACTOR AND ELECTRICAL CONTRACTOR SHALL REVIEW SHOP DRAWING SUBMITTALS FOR COMPLIANCE, CONTENT AND COMPLETENESS AND PROVIDE A STAMP WITH THE DATE OF REVIEW AND SIGNATURE OF THE REVIEWER. TRANSMITTAL PAGE SHALL HAVE INDEX WITH SPECIFICATION SECTION AND DESCRIPTION OF SUBMITTED ITEMS. NO EXCEPTIONS WILL BE TAKEN. SHOP DRAWINGS NOT SUBMITTED IN THIS FORMAT WILL BE REJECTED AND WILL NOT CAUSE REASON FOR PROJECT DELAYS. EQUIPMENT SHALL NOT BE ORDERED UNTIL ENGINEER OF RECORD HAS PROCESSED APPLICABLE SHOP DRAWINGS. A MINIMUM OF SEVEN WORKING DAYS WILL BE ALLOWED FOR SUBMITTAL PROCESSING BY THE ENGINEER. REFER TO PROJECT MANUAL FOR ADDITIONAL REQUIREMENTS.ELECTRICAL WORK SHALL BE PROVIDED TO COMPLY WITH NFPA 70, THE 2008 NATIONAL ELECTRICAL CODE (NEC), AS WELL AS ALL APPLICABLE LOCAL ORDINANCES, STATE LAWS AND FEDERAL LAWS.ELECTRICAL CONTRACTOR SHALL UNDERSTAND THE PRODUCT, MEANS AND METHODS OF INSTALLATION. ALL CONDUCTORS AND EQUIPMENT SHALL BE APPROVED AND LISTED BY A NRTL (NATIONALLY RECOGNIZED TESTING INSTRUCTIONS INCLUDED IN THE LISTING AND LABELING IN ADDITION TO THE WRITTEN INSTALLATION INSTRUCTIONS AND METHODS OF INSTALLATION AS PUBLISHED BY THE MANUFACTURER OF THE EQUIPMENT OR MATERIAL PROVIDER. THE ELECTRICAL CONTRACTOR SHALL OBTAIN THE INSTALLATION INSTRUCTIONS AND REQUIREMENTS PRIOR TO BID. ALL RFI AND CLARIFICATIONS OF SCOPE PRESENTED DURING CONSTRUCTION WHERE THE CONTRACTOR HAS NOT PREVIOUSLY OBTAINED THIS INFORMATION FOR BIDDING PURPOSES WILL NOT SYSTEMS ARE SHOWN AS DIAGRAMMATIC AND GIVE THE GENERAL ARRANGEMENT ONLY. EXACT LOCATIONS SHALL BE DETERMINED IN THE FIELD ON THE BASIS OF DETAIL DRAWINGS, REVIEWED DRAWINGS, AND SUPPLEMENTARY INFORMATION. INSTALLATION SHALL PROVIDE FOR OPERATING EFFICIENCY, NEATNESS OF APPEARANCE, EASE OF MAINTENANCE, AND NEC COMPLIANCE. IT IS EXPECTED THAT THE CONTRACTOR WILL PREPARE DIMENSIONED FIELD ERECTION DRAWINGS AND WORK SKETCHES FOR USE BY THEIR INSTALLERS, TO ENSURE PROPER INSTALLATION AND COORDINATION. THE ELECTRICAL CONTRACTOR SHALL TAKE THEIR OWN MEASUREMENTS AT THE BUILDING, AND BE RESPONSIBLE FOR THE CORRECT INTERPRETATION AND USE OF ALL SIZES AND DIMENSIONS. ALL CONTRACTORS SHALL ATTEND COORDINATION MEETINGS TO COORDINATE THE K - INFORMATION DURING CONSTRUCTION AND FURNISH TO THE OWNER A RECORD SET OF BLACK LINE PRINTS AT THE PROJECT COMPLETION.126596881372284126596881214523126596881528650126582922020083126596881842776PANELBOARD SCHEDULEDESIGNATION/I.D:AC/3PH-4WTYPE OF PANEL:CIRCUIT BREAKER **MOUNTING: SURFACEVOLTAGE: POLES: FEEDER:C K120 / 208BUS SIZE (AMPS):6003PSNLUGS:STANDARD TOTAL SPACE REQUIRED:30MAIN SWITCH:NOTES:M.L.O.MAIN RATING AIC 10kSEE RISER DIAGRAMPOWER SOURCE:LOAD (WATTS)T# 1357911131517192123252729C/BC L A S SLOAD DESCRIPTIONLOAD DESCRIPTIONC L A S SLOAD (WATTS)C/B 3540 C K T#M3 AUDITORIUM AHU-1M3GYM AHU-2M3 1800 40/3-- 175/3-- 20/120/120/120/120/120/120/120/120/13540----12591-- M3-- M3 A318003540M3180012591A3 AUDITORIUM CU-1A3GYM CU-2719112591A3------ A3-- A3 A371917191600R GFCI SERVICE RECEPTACLES R U SPARESPARE12780-- A3-- A3-1278012780SPARESPARESPARESPARESPARESPARESPARE SPARE SPARE SPARE SPARESPARE-----20/3-- 90/3-- 150/3-- 20/120/120/120/120/120/124681012141618202224262830TOTALS167311613116131217712177121771TOTALSCONNECTED LOAD: (VOLT-AMPERE)114,306VANOTES:* PROVIDE LOCK ON DEVICE** 10,000 A.I.C. RATING UNLESS OTHERWISE SPECIFIEDCALC. DEMAND LOAD AMPERE:344ACLASS: M1=SINGLE PH MOTOR, M3=3PH MOTOR, M2=2PH MOTOR, L=LIGHTING, R=RECEPTACLE, A1=1PH A/C LOAD, A2=2PH A/C LOAD, A3=3PH A/C LOAD, H=HEATING, K=KITCHEN; XF=TRANSFORMER-PANEL; SF=SUB-FEEDALL ELECTRICAL WORK SHALL BE DONE UNDER THE SUPERVISION OF THE ELECTRICAL CONTRACTOR, WHO SHALL PROVIDE A COMPETENT AND SKILLED FOREMAN TO LAYOUT AND SUPERVISE ALL WORK. ALL WORK SHALL BE PROVIDED WITH DUE REGARD FOR THE SPACE REQUIREMENTS OF THE OTHER CONTRACTORS. THE ELECTRICAL CONTRACTOR SHALL REPORT ANY CONFLICTS OR DIFFICULTIES IN REGARD TO THE INSTALLATION IMMEDIATELY TO THE GENERAL CONTRACTOR. WHERE CROWDED LOCATIONS EXIST OR WHERE THERE IS A POSSIBILITY OF CONFLICT BETWEEN TRADES, THE ELECTRICAL CONTRACTOR SHALL MAKE COMPOSITE SUPPLEMENTARY DRAWINGS SHOWING THE EXACT LOCATIONS OF PIPES, CONDUIT, DUCTS AND EQUIPMENT. DRAWINGS SHALL BE BASED ON FIELD MEASUREMENTS, AND AFTER CONSULTATION AND AGREEMENT AMONG THE TRADES, THE GENERAL CONTRACTOR SHALL DIRECT THE SOLUTION BEFORE INSTALLATION OF THE WORK.PRIOR TO BIDDING THIS PROJECT, THE ELECTRICAL CONTRACTOR SHALL CONTACT THE ELECTRICAL UTILITY COMPANY. ELECTRICAL CONTRACTOR SHALL CONFIRM THE PROPOSED ELECTRICAL SERVICE TO THE BUILDING12792319-136016The Professional Engineer's seal and signature apply only to the document to which they are affixed. The Engineer expressly disclaims any responsibility for all other plans, specifications, estimates, reports or other documents or instruments relating to or intended to be used for any part of the engineering project.2017 G&W Engineering Corp.2017-0214.00WITH THE UTILITY COMPANY. ELECTRICAL CONTRACTOR SHALL PROVIDE, BUT IS NOT LIMITED TO, CONDUIT, CABLE, CONNECTIONS, GROUNDING EQUIPMENT, METER BASE, POTENTIAL TRANSFORMERS, CURRENT TRANSFORMERS,HARDWARE, CABINETS AND RELATED EQUIPMENT REQUIRED FOR A COMPLETE ELECTRICAL SERVICE FROM THE UTILITY COMPANY SECONDARY TERMINATION TO THE MAIN SERVICE EQUIPMENT BUS. IT SHALL BE THERESPONSIBILITY OF THIS CONTRACTOR TO COORDINATE SERVICE ENTRANCE ELECTRICAL WORK WITH THE UTILITY1279231964762COMPANY PRIOR TO THE START OF CONSTRUCTION. SUBMIT SHOP DRAWINGS AND COORDINATE WITH THE UTILITY COMPANY FOR THE INSTALLATION OF THE METER, CURRENT TRANSFORMERS, POWER TRANSFORMERS, METERING L THE BID THAT ENSURES A COMPLETE, APPROVED ELECTRICAL SERVICE INSTALLATION. SUBMISSION OF A BIDACKNOWLEDGES YOU HAVE PERFORMED THIS CONTRACT REQUIREMENT AND HAVE INCLUDED ALL NECESSARY MATERIALS AND LABOR FOR A COMPLETE AND OPERABLE ELECTRICAL SERVICE.FIELD COORDINATION: THE ELECTRICAL CONTRACTOR SHALL COMPLETELY REVIEW THE ENTIRE SET OF12792319156365CONSTRUCTION DRAWINGS FOR DETAILS OF CONSTRUCTION PRIOR TO STARTING WORK. ROUGH-IN OF ELECTRICAL CONDUIT, BOXES, SIGNALS, DEVICES, EQUIPMENT AND FIXTURES SHALL BE BASED ON THIS REVIEW. PRIOR TO START OF CONSTRUCTION. ALL LIGHT SWITCHES SHALL BE LOCATED BEYOND DOOR SWINGS, TRIM, ANDThis electronic drawing file is released under the authority of KEVIN S. GRIESEMER, Missouri License # PE-23628 who maintains the original file and who's registration expires on December 31, 2018. This electronic drawing file may be used as a background drawing. Pursuant to State of Missouri Regulations of the Missouri Board for Architects, Professional Engineers, Professional Land Surveyors, and Landscape Architects, the user of this electronic drawing file agrees to assume all responsibility for any modification to or use of this drawing file that is inconsistent with the requirements of the Rules and Regulations of the Missouri Code of State Regulations Title 4, Division 30. No person may make any modifications to this electronic drawing file without the Engineers express written permission.ON THE LATCH SIDE OF THE DOOR. COORDINATE ELECTRICAL DEVICE LAYOUT AND FRAMING WITH GENERAL CONTRACTOR PRIOR TO START OF CONSTRUCTION.PROVIDE FIRE STOP AT EACH RATED WALL, FLOOR, AND CEILING-ROOF ASSEMBLY PENETRATION. FIRE STOP L APPLICATION DETAILS AND INSTRUCTIONS. PROVIDE TAGGED CERTIFICATIONS AT EACH PENETRATION. PROVIDE SHOP DRAWINGS FOR REVIEW WITH THE U.L. LISTING AND TEST CRITERIA. PROVIDE FIRE STOPPING WHERE12786735133928 REFER TO THE PROJECT MANUAL FOR SYSTEMS SPECIFICATIONS.PROVIDE CONDUIT, CABLES, AND ELECTRICAL ASSEMBLY PENETRATIONS OF NON-RATED ASSEMBLIES WITH DRAFT STOPPING, OR SMOKE BARRIER SEALANT SYSTEMS. THROUGH PENETRATION SEALANT SYSTEMS SHALL BE L INSTRUCTIONS. PROVIDE DRAFT STOPPING OR SMOKE BARRIER SEALANTS TO MEET APPROVAL OF THE AHJ. EQUAL 1921027322238ELECTRICAL CONTRACTOR SHALL CUT AND PATCH ROOF, FLOORS, WALLS, AND CEILINGS WHERE REQUIRED TO INSTALL NEW ELECTRICAL BOXES, FIXTURES, AND RACEWAY SYSTEMS. SURFACES SHALL BE PATCHED AND LEFT READY FOR FINAL SCHEDULED FINISH. ROOFING WORK SHALL BE PERFORMED BY A QUALIFIED ROOFING CONTRACTOR THAT MAINTAINS THE ROOF WARRANTY. ALL REQUIRED ROOFING WORK DUE TO ELECTRICAL SCOPE K L HVAC UPGRADES TOKIPP: INSPIRE ACADEMYMIDDLE SCHOOL1212 N. 22ND STREET ST. LOUIS, MO 63106ELECTRICAL CONTRACTOR SHALL PROVIDE ALL TEMPORARY POWER AND LIGHTING FOR THE DURATION OF THE PROJECT. ALL TEMPORARY LIGHTING AND POWER SHALL BE PROVIDED TO MEET OSHA STANDARDS, STATE LAW, LOCAL ORDINANCES AND AHJ REQUIREMENTS. REMOVE ALL TEMPORARY POWER AND LIGHTING AT THE PROJECT COMPLETION.THE ELECTRICAL CONTRACTOR SHALL DISCONNECT AND REMOVE ALL EXISTING ELECTRICAL EQUIPMENT OCCURRING IN DEMOLISHED WALLS, FLOORS, ATTICS, CEILING CAVITIES, THE ROOF AND AS OTHERWISE DESCRIBED HEREIN AND AS SHOWN ON THE DRAWINGS. REFER TO THE ARCHITECTURAL DRAWINGS FOR THE GENERAL SCOPE OF DEMOLITION. ELECTRICAL COMPONENTS INCLUDING MOTORS, TEMPERATURE CONTROL DEVICES, LIGHT FIXTURES, PIPING, FITTINGS, CONDUIT, WIRE, HANGERS, BRACKETS, INSULATION, ETC., NOT TO BE RETAINED BY THE OWNER OR TENANT, MUST BE REMOVED FROM THE PREMISES AND BE LEGALLY DISPOSED OF BY THE ELECTRICAL CONTRACTOR. ALL LOOSE ENDS OF SYSTEMS WHERE SUCH ABANDONMENT HAS TERMINATED SHALL BE TRIMMED CLEAR AND APPROPRIATELY CAPPED OR SEALED IN A SAFE AND SECURE MANNER. REMOVAL AND DEMOLITION SHALL BE BY THE RESPECTIVE OR APPROPRIATE TRADES. MAINTAIN BRANCH CIRCUIT CONTINUITY TO ADJOINING AREAS AS NEEDED. THIS INCLUDES, BUT IS NOT LIMITED TO, REMOVAL, MODIFICATION AND REINSTALLATION OF EQUIPMENT AS NEEDED TO SUSTAIN THE EXISTING WORKING CONDITION OF ALL ELECTRICAL EQUIPMENT AND TO RETURN THESE AREAS TO FULL WORKING ORDER AT PROJECT COMPLETION.12789527663692THIS ELECTRICAL CONTRACTOR SHALL CONFINE THEIR ACTIVITIES TO THE AREA SET ASIDE FOR THEM TO DO THEIR WORK AND SHALL NOT INTERFERE WITH ANY OF THE OWNER'S OR TENANT ACTIVITIES. THE ELECTRICAL CONTRACTOR WILL NOT BE PERMITTED TO STORE MATERIAL EXCEPT WITHIN THE AREAS AS DIRECTED BY THE GENERAL CONTRACTOR. SHOULD ANY DISTURBANCE OF THE EXISTING INSTALLATION BE NECESSARY, THE ELECTRICAL CONTRACTOR SHALL SO INFORM THE OWNER WELL IN ADVANCE OF THE TIME CONTEMPLATED FOR THE DISTURBANCE. AFTER A PLAN ACCEPTABLE TO THE OWNER OR TENANT HAS BEEN FORMULATED AND AGREED TO IN WRITING BY ALL PARTIES, THE GENERAL CONTRACTOR SHALL KEEP IN CLOSE PERSONAL CONTACT WITH THE WORK TO SEE THAT IT IS EXECUTED IN ACCORDANCE WITH THE AGREED-UPON PROCEDURE.128286184178412684817417841282861819954512659687984164CONTINUITY OF ALL BUILDING SERVICES AND UTILITIES SERVING FACILITIES IN THE BUILDING SHALL BE MAINTAINED WITHOUT INTERRUPTION, EXCEPT FOR SUCH A PERIOD OF TIME DESIGNATED BY THE GENERAL CONTRACTOR. THE ELECTRICAL CONTRACTOR SHALL SO ARRANGE AND EXECUTE THEIR WORK SUCH THAT ANY CONNECTIONS, EITHER TEMPORARY OR PERMANENT, OR REARRANGEMENT OF PRESENT EQUIPMENT, CONDUIT, WIRING, ETC., SHALL BE IN SUCH A MANNER AS TO ASSURE FULL RESUMPTION OF SERVICE AT THE TIME DESIGNATED BY THE GENERAL CONTRACTOR. IF TEMPORARY CROSS CONNECTIONS, CONDUIT, WIRING, SWITCHES ETC., ARE NECESSARY TO ASSURE THIS CONTINUITY OF THE BUILDING SERVICE, THE ELECTRICAL CONTRACTOR SHALL PROVIDE THEM TO THE GENERAL CONTRACTOR AT NO ADDITIONAL COST. WHERE USED IN THESE DOCUMENTS, MAINTAIN IS DEFINED AS FOLLOWS: SUSTAIN THE EXISTING WORKING CONDITION OF ELECTRICAL DEVICES AND EQUIPMENT, WHICH INCLUDES, BUT IS NOT LIMITED TO, REVISING, REMOVING AND REINSTALLING TO PERFORM THE NEW WORK INDICATED.18896147124236661915791812422968127853381059824212786735107392501273228611199271127853381012635412747643102841151278533810440481ELECTRICAL ABBREVIATIONS1PH3PH3PL3PSN (60/50/3) AAIC AFCI AFF AHJ AHU AL ALT ATS AWG BB BDD BES BFF BMS CKT CLGC/B CCTV COND CCP CU CUH CT DC DDC DISC DN DPST DRE (E) EBB EC EF EOL EMS EMT EUHEWC EWH EXIST FFA FAAP FACP FCU FDR FPC FSD FSC FTU FV GC GF GFI GRD GRS GWH HID HOA HP HPS HWCHWRCP HZIG IMC JB kVARkVA KW LCP LC MATV MAX MC MIC MIN MCA MCB MCC MAH MH MLO MOCP MTD NC NF NIC NL NO PCPF PH PRI PT PVC REC RF RL RT RTU SEC SD SF SWSWBD TTC TEB TEF TEMP TV TVSS TYP UH UNV UON VVA VAV VFD VOIP VSD WW/ WP WSHP WT XFMRSINGLE PHASE (LINE-LINE) 3 PHASE (L1-L2-L3)THREE POLE3 POLE SOLID NEUTRAL AMP SIZE/FUSE SIZE/POLES AMPERE(S)AMPERES INTERRUPTING CAPACITY ARC FLASH CIRCUIT INTERRUPTER ABOVE FINISHED FLOOR AUTHORITY HAVING JURISDICTION AIR HANDLING UNITALUMINUM ALTERNATEAUTOMATIC TRANSFER SWITCH AMERICAN WIRE GAUGE BASEBOARD HEATERBACK DRAFT DAMPERBANKING EQUIPMENT SUPPLIER BELOW FINISHED FLOOR BUILDING MANAGEMENT SYSTEM CIRCUITCEILINGCIRCUIT BREAKERCLOSED CIRCUIT TELEVISION CONDUCTORCONDUIT (SEE RACEWAYS AND CONDUCTORS) CONTROL PANELCOPPERCABINET UNIT HEATER CURRENT TRANSFORMER DIRECT CURRENTDIRECT DIGITAL CONTROL DISCONNECTDOWNDOUBLE POLE SINGLE THROW DUPLEX RECEPTACLE EMERGENCYEXISTINGELECTRIC BASE BOARD ELECTRICAL WORK CONTRACTOR EXHAUST FANEND LINE RESISTORENERGY MANAGEMENT SYSTEM ELECTRICAL METALLIC TUBING ELECTRIC UNIT HEATER ELECTRIC WATER COOLER ELECTRIC WATER HEATER EXISTINGFLUORESCENT FIRE ALARMFIRE ALARM ANNUNCIATOR PANEL FIRE ALARM CONTROL PANELFAN COIL UNIT FEEDERFIRE PROTECTION CONTRACTOR FIRE/SMOKE DAMPERFOOD SERVICE CONSULTANT FAN TERMINAL UNITFIELD VERIFYGENERAL WORK CONTRACTOR GAS FURNACEGROUND FAULT INTERRUPTER GROUNDGALVANIZED RIGID STEEL CONDUIT GAS WATER HEATERHIGH INTENSITY DISCHARGE HAND-OFF-AUTO HORSEPOWERHIGH PRESSURE SODIUM HEAVY WALL RIGID CONDUITHOT WATER RETURN CIRCULATING PUMP HERTZISOLATED GROUNDINTERMEDIATE METALLIC CONDUIT JUNCTION BOXKILOVAR(S) KILOVOLT AMPERE(S) KILOWATT(S)LIGHTING CONTROL PANEL LIGHTING CONTACTOR MASTER ANTENNA TELEVISION MAXIMUMMECHANICAL WORK CONTRACTOR MICROPHONEMINIMUMMINIMUM CIRCUIT AMPERES MAIN CIRCUIT BREAKER MOTOR CONTROL CENTER MANHOLEMETAL HALIDE MAIN LUGS ONLYMAXIMUM OVERCURRENT PROTECTION MOUNTEDNORMALLY CLOSED NON FUSEDNOT IN CONTRACT NIGHT LIGHT NORMALLY OPENPLUMBING WORK CONTRACTOR POWER FACTORPHASE PRIMARYPOTENTIAL TRANSFORMER POLYVINYL CHLORIDE RECEPTACLERETURN FANEXISTING DEVICE RELOCATED RAIN TIGHT (NEMA 3R)ROOF TOP UNIT SECONDARY SMOKE DAMPER SUPPLY FAN SWITCH SWITCHBOARD TELEPHONE TIMECLOCKTELEPHONE EQUIPMENT BOARD TOILET EXHAUST FAN TEMPORARYTELEVISIONTRANSIENT VOLTAGE SURGE SYMBOL TYPICALUNIT HEATER UNIVERSALUNLESS OTHERWISE NOTED VOLT(S)VOLTAMP(S)VARIABLE AIR VOLUME VARIABLE FREQUENCY DRIVE VOICE OVER IPVARIABLE SPEED DRIVE WATT(S)WITH WEATHERPROOFWATER SOURCE HEAT PUMP WATERTIGHT TRANSFORMER126582929035986ELECTRICAL SYMBOL LISTOUTLETS SINGLE RECEPTACLE (+18")DUPLEX RECEPTACLE (+18")QUADPLEX RECEPTACLE (+18")WPWEATHERPROOF RECEPTACLE GFI TYPE RECEPTACLE ISOLATED GROUND TYPE D.R.TRTAMPER RESISTANT RECEPTACLEUSBUSB CHARGER RECEPTACLESWITCHED RECEPTACLE D.R. - TOP HALF SWITCHED FLUSH FLOOR BOX. SEE PLANS.FSURFACE FLOOR RECEPTACLE. SEE PLANS.SSPECIAL PURPOSE OUTLET. SEE PLANS. VOICE OUTLET BOXDATA OUTLET BOX VOICE/DATA OUTLET BOXJJUNCTION BOX - WALL MTD.JJUNCTION BOX - CEILING MTD. (+XX")MOUNTING HEIGHT TO CENTERLINESWITCHESXSINGLE POLE SWITCH (+42")x33-WAY SWITCH (+42")x44-WAY SWITCH (+42")SSWITCH WITH PILOT LIGHTxCOMB. SWITCH/DUPLEX RECEPTACLETO xTHERMAL OVERLOAD SWITCHM xMANUAL MOTOR SWITCHL xLOW-VOLTAGE SWITCHK xKEYED SINGLE POLE SWITCH (+42")K x3KEYED THREE-WAY SWITCH (+42")WPWEATHERPROOF SWITCHTTIME SWITCHSMOTION DETECTOR SWITCHDDIMMER SWITCHFIXTURESRECESSED DOWN LIGHTING FIXTURE WALL MOUNTED LIGHT FIXTURE PENDANT LIGHT FIXTURE 2x2 / 2x4 LIGHT FIXTURE LIGHT FIXTURE WITH EMERGENCY BATTERY EXIT SIGN WITH FACES & ARROWSEMERGENCY EGRESS LIGHT W/ BATTERYFIRE ALARMFMANUAL PULL STATIONFAUDIO/VISUAL ALARM HORN (+80") HAUDIO/VISUAL MINI ALARM HORN STROBE LIGHT ONLY (+80")FSMOKE DETECTOR (CEILING MTD.)SFTHERMAL DETECTOR (CEILING MTD.)TFSUPPLY AIR SMOKE DETECTORSAFRETURN AIR SMOKE DETECTOR w/ SAMPLING TUBERAFR.T.U./A.H.U. SHUTDOWN RELAYSRFCONTROL MODULECMFMONITOR MODULEMMF.A.A.P. FIRE ALARM ANNUCIATOR PANELF.A.C.P. FIRE ALARM CONTROL PANELSERVICE AND EQUIPMENTRRELAYN/F DISCONNECT SWITCHFFUSED DISCONNECT SWITCH STARTER COMBINATION STARTER/DISC. SW. PUSHBUTTON OR CONTROL STATION PHOTOCONTROL MOTORENCLOSED CIRCUIT BREAKER MAIN DISTRIBUTION PANEL BRANCH CIRCUIT PANELBOARDXXEQUIPMENT CALLOUTXXX X XPLAN NOTE SYMBOLXREVISION SYMBOLCIRCUITRY AND RACEWAYSCONCEALED CONDUIT(2 #12 AWG & APPROVED GROUND MIN. - TYP.) CONDUIT BELOW FLOOR OR GRADECONDUIT EXPOSED GROUND WIREISOLATED GROUND WIREHOMERUN: NUMBER OF WIRES, PANEL P1-2,4,6DESIGNATION, CIRCUIT NUMBERSSEALREVISIONSJOB NO:2017-0214.00DRAWN BY:J.R.A.CHECKED BY:J.R.A.DATE:09-25-2017SHEET NO. ELECTRICAL TITLE SHEETTO MAIN WATER PIPE. CONNECT AHEAD OF MAIN SHUT OFF VALVE. TYPE "VN" EXOTHERMIC WELD OR LISTED GROUND CLAMP.TO BUILDING STEEL. TYPE "VS"EXOTHERMIC WELD#6OR LISTED MECHANICALCONNECTOR.#6TYPE "GR" EXOTHERMIC WELD OR LISTED MECH. CONNECTOR.GROUNDING ELECTRODE CONDUCTOR FROM MAIN SERVICE EQUIPMENT. SEE RISER DIAGRAM FOR SIZE OF CONDUCTOR.#6GROUNDING PLATE LOCATED IN COMMUNICATION ROOMSWHERE NOTED.2"x12"x1/4" CU GROUNDING PLATE LOCATED AT MAIN PANEL#4PLAN NOTES - RISER DIAGRAM#The Professional Engineer's seal and signature apply only to the document to which they are affixed. The Engineer expressly disclaims any responsibility for all other plans, specifications, estimates, reports or other documents or instruments relating to or intended to be used for any part of the engineering project.2017 G&W Engineering Corp.2017-0214.00EXISTING AMEREN MANHOLE. COORDINATE CORE DRILLING AND CONNECTING NEW PRIMARY CONDUITS.PROVIDE TWO 5" PVC C. WITH PULL STRING ENCASED IN CONCRETE PER AMEREN STANDARDS.NEW AMEREN GEAR SET ON PRECAST PAD. CONTRACTOR SHALL PICKUP PAD FROM AMEREN AND SET PAD PER AMEREN STANDARDS.PROVIDE ONE 5" PVC C. WITH PULL STRING FROM GEAR TO TRANSFORMER.NEW AMEREN PAD MOUNT TRANSFORMER SET ON PRECAST PAD. CONTRACTOR SHALL PICKUP PAD FROM AMEREN AND SET PAD PER AMEREN STANDARDS.18360039283313INSTALL 1200A SERVICE FEEDERS NOW WITH TWO EMPTY CONDUITS ALLOWING EXPANSION TO 1600A IN FUTURE. (4 - SETS) OF 3 #500 KCMIL ALUM & 1 #350 KCMIL ALUM GRD, 4" PVC C. PROVIDE TWO ADDITIONAL 4" C WITH PULL STRING FOR FUTURE.This electronic drawing file is released under the authority of KEVIN S. GRIESEMER, Missouri License # PE-23628 who maintains the original file and who's registration expires on December 31, 2018. This electronic drawing file may be used as a background drawing. Pursuant to State of Missouri Regulations of the Missouri Board for Architects, Professional Engineers, Professional Land Surveyors, and Landscape Architects, the user of this electronic drawing file agrees to assume all responsibility for any modification to or use of this drawing file that is inconsistent with the requirements of the Rules and Regulations of the Missouri Code of State Regulations Title 4, Division 30. No person may make any modifications to this electronic drawing file without the Engineers express written permission.NEW SECONDARY FEEDERS EXPOSED FROM FOUNDATION TO "MSB" (APPROXIMATELY 8'-0" LENGTH).COPPER CLAD GROUND ROD TYPICAL, 5/8"x10'.NOTE:MAIN GROUND ELECTRODE CABLE. SIZE ASNOTED ON THE RISER DIAGRAM.FOUNDATION CONTRACTOR SHALL STUB-UP RE-BAR FROM FOUNDATION FOR USE BY THE E.C. TYPE "VS" CONNECTION OR LISTED MECH. CONNECTOR. E.C. SHALL COORDINATE WITH FOUNDATION CONTRACTOR PRIOR TO CONCRETE POUR.METER WIRING IN 1 1/2" RIGID METALLIC CONDUIT PER AMEREN STANDARDS.PROVIDE AMEREN APPROVED METER SOCKET. REFER TO AMEREN ELECTRIC SERVICE MANUAL FOR SPECIFICATIONS.PROVIDE A 4" TALL HOUSEKEEPING PAD POURED ON TOP OF THE EXISTING SLAB. PAD SHALL BE 6" LARGER THAN THE EQUIPMENT. SEISMICALLY ANCHOR THE NEW PAD TO THE EXISTING SLAB WITH 1/2" REBAR DOWELS ADHESIVELY ANCHORED INTO THE EXISTING SLAB. DOWELSSECTION 1SECTION 2CURRENT TRANSFORMER SECTIONPULLSECTION(M5) 400/3(M4) 800/3(M3) 30/3(M2) 600/3(M1) 600/3EXOTHERMIC WELD DESIGNATION INDICATED ABOVE ARE ERICO "CADWELD". LISTED MECHANICAL CONNECTORS ARE AN ACCEPTABLE ALTERNATE.ALL GROUND BUS CONNECTIONS TO BE MADE WITH 2-HOLE COMPRESSION TYPE CONNECTORS. BUS SHALL BE INSULATED FROM ITS SUPPORT AND SHALL MAINTAIN A 2" SPACING FROM WALL.ALL WIRING SHALL BE COPPER AND TYPE THHN/THWN GREEN INSULATION WHERE REQUIRED.."MSB"120/208V. - 30 - 4W. 1600 AMP MAIN SWITCHBOARD W/ C/T SECTION AND LABELED FOR SERVICE ENTRANCE. PROVIDE GROUND BUS. PROVIDE TRANSIENT VOLTAGE SURGE SUPPRESSOR. PANEL SHALL BE SIEMENS, OR EQUAL BY CUTLER HAMMER, SIEMENS, OR SQUARE D.SHALL BE 12" O.C. AND 6" FROM EDGE OF PAD. PROVIDE A 1/2" REBAR GRID ON 10"x10" SPACING AND HOOK UNDER AN "L" BEND AT TOP OF DOWELS. ANCHOR SWITCHBOARD TO PAD WITH A MINIMUM OF FOUR 1/4" ANCHOR BOLTS PER SECTION WITH 2 1/2" EMBEDMENT.1921027350161#3/0 CU GRD PER NEC ART 250. REFER TO DETAIL 1/E1.1 FOR GROUNDING ELECTRODE SYSTEM REQUIREMENTS.(2-SETS) OF 4 #350 KCMIL CU & 1 #1 GRD, 3" C.3.GROUND RODS ARE TO BE LOCATED AT SERVICE ENTRANCE WITH SIZE AS NOTED.HVAC UPGRADES TOKIPP: INSPIRE ACADEMYMIDDLE SCHOOL1212 N. 22ND STREET ST. LOUIS, MO 631064.SWITCH SCHEDULEALL GROUNDING AND BONDING SHALL BE INSTALLED IN ACCORDANCE WITH ARTICLE 250 OF NFPA 70 THE5. "NATIONAL ELECTRICAL CODE".NO.CIRCUIT BREAKER SIZEPOLESLOAD4GROUNDING ELECTRODE SYSTEMSECTION 2M16003EXISTING SWITCHBOARD "SB2"E1.1NO SCALEM26003PANELBOARD "AC"M3303TVSSM48003PREPARED SPACEM54003PREPARED SPACE3E1.12E101REVISIONSJOB NO:2017-0214.00DRAWN BY:J.R.A.CHECKED BY:J.R.A.DATE:09-25-2017SHEET NO.ELECTRICAL SCHEDULES & DETAILSSWITCHBOARD "MSB" DETAIL"AC" 600A M.L.O.TUNNEL9M35GRADE1ST FLRKITCHENPE OFFICE2E1.1812EXISTING SWITCHBOARD "SB2"SECTION 1SECTION 212124PULLTUNNEL674E1.01CT/PTLOWER LEVELREMOVE GROUND-NEUTRAL BONDS11ELECTRICAL RISER DIAGRAMNO SCALE10SEAL1894361512015419206782120154NO SCALE#The Professional Engineer's seal and signature apply only to the document to which they are affixed. The Engineer expressly disclaims any responsibility for all other plans, specifications, estimates, reports or other documents or instruments relating to or intended to be used for any part of the engineering project.2017 G&W Engineering Corp.2017-0214.00PLAN NOTES - ELECTRICAL DEMOLITIONDISCONNECT POWER FROM EXISTING AIR HANDLING UNIT. REMOVE DISCONNECT, STARTER, WIRING, RACEWAYS, FIRE ALARM SYSTEM DUCT DETECTOR, AND ASSOCIATED ELECTRICAL COMPONENTS.1213MECHANICAL AHUMEZZANINE1338AHU 2FAC-2,4,6RAAC-1,3,5 74#12FCM#8DISCONNECT POWER FROM EXISTING RETURN AIR FAN. REMOVE DISCONNECT, WIRING, RACEWAY AND ASSOCIATED ELECTRICAL COMPONENTS.EXISTING PANELBOARD AND FEEDERS SHALL REMAIN. LABEL EXISTING BREAKERS RENDERED UNUSED AS A RESULT OF THIS PROJECT AS SPARE.NMECHANICAL MEZZANINE DEMOLITION PLANSCALE: 1/8" = 1'-0"NMECHANICAL MEZZANINE MECHANICAL PLANSCALE: 1/8" = 1'-0"PLAN NOTES - ELECTRICAL#This electronic drawing file is released under the authority of KEVIN S. GRIESEMER, Missouri License # PE-23628 who maintains the original file and who's registration expires on December 31, 2018. This electronic drawing file may be used as a background drawing. Pursuant to State of Missouri Regulations of the Missouri Board for Architects, Professional Engineers, Professional Land Surveyors, and Landscape Architects, the user of this electronic drawing file agrees to assume all responsibility for any modification to or use of this drawing file that is inconsistent with the requirements of the Rules and Regulations of the Missouri Code of State Regulations Title 4, Division 30. No person may make any modifications to this electronic drawing file without the Engineers express written permission.CONNECT CONDENSING UNIT COMPLETE AND READY FOR OPERATION. FACTORY DISCONNECT AND GFCI RECEPTACLE PROVIDED WITH UNIT FOR FIELD WIRING. COORDINATE WITH M.C.AlLTERNATE BID #1: CONNECT ROOFTOP UNIT COMPLETE AND READY FOR OPERATION. FACTORY DISCONNECT AND GFCI RECEPTACLE PROVIDED WITH UNIT FOR FIELD WIRING. COORDINATE WITH M.C.CONNECT AIR HANDLING UNIT COMPLETE AND READY FOR OPERATION. FACTORY VFD PROVIDED WITH UNIT FOR FIELD WIRING. COORDINATE WITH M.C.1921027390648NEW PANELBOARD; FIELD LOCATE TO MAINTAIN NEC SERVICE CLEARANCES.CORE DRILL FLOOR SLAB THEN EXTEND PANEL FEEDERS FROM TUNNEL TO ABOVE KITCHEN CEILING. INSTALL VERTICAL CONDUIT ON STANDOFFS TO ALLOW CLEANING OF WALL BEHIND CONDUIT. REMOVE AND REINSTALL CEILING GRID/PADS AS REQUIRED FOR INSTALLATION.HVAC UPGRADES TOKIPP: INSPIRE ACADEMYMIDDLE SCHOOL1212 N. 22ND STREET ST. LOUIS, MO 63106CORE DRILL MEZZANINE FLOOR SLAB THEN EXTEND PANEL FEEDERS FROM FIRST FLOOR CEILING TO NEW PANEL ON MEZZANINE.RELOCATE AN EXISTING RETURN AIR DUCT SMOKE DETECTOR TO NEW RETURN AIR DUCT AND PROVIDE INTERLOCK FOR UNIT SHUTDOWN UPON DETECTION OF SMOKE. PROVIDE NEW SAMPLING TUBE. PROVIDE FIRE ALARM SYSTEM PROGRAMMING AND TESTING.UNIT SERVES A SINGLE AREA; RETURN AIR DUCT SMOKE DETECTOR IS NOT REQUIRED.VIDEOFIED SURVEILLANCE AND SECURITY SYSTEM - BY OWNER. #2/0AC-7,9,11 AC-13CU 1ON ROOF ABOVE1AUDITORIUM GYMCAFETERIA#3AC-8,10,12 AC-13 CU 2ON ROOF ABOVE19RTU 128AC-14,16,18 AC-13DROP BELOW STRUCTUREROUTE ABOVE KITCHEN CEILING5RUN ALONG CEILINGKITCHEN6#1/0SEALREVISIONSJOB NO:2017-0214.00DRAWN BY:J.R.A.CHECKED BY:J.R.A.DATE:09-25-2017SHEET NO.ENLARGED PLANS - ELECTRICALNPARTIAL FIRST FLOOR MECHANICAL PLANSCALE: 1/8" = 1'-0"1890173123792719097187239469192486662372293248950-53402509J5STORAGE"MSB"UPDN6BOILER ROOM7NTUNNEL8OVERALL PLANSCALE: 1/16" = 1'-0"TUNNELROUTE NEW PANEL "AC" FEEDERS THROUGH THE TUNNEL TIGHT TO CEILING OR WALL OF TUNNEL.CORE DRILL FIRST FLOOR SLAB THEN EXTEND FEEDERS UP INTO KITCHEN AREA.SAW CUT AND REMOVE SECTION OF SIDEWALK FOR INSTALLATION OF NEW ELECTRICAL RACEWAYS. BACKFILL THEN POUR NEW SIDEWALK.This electronic drawing file is released under the authority of KEVIN S. GRIESEMER, Missouri License # PE-23628 who maintains the original file and who's registration expires on December 31, 2018. This electronic drawing file may be used as a background drawing. Pursuant to State of Missouri Regulations of the Missouri Board for Architects, Professional Engineers, Professional Land Surveyors, and Landscape Architects, the user of this electronic drawing file agrees to assume all responsibility for any modification to or use of this drawing file that is inconsistent with the requirements of the Rules and Regulations of the Missouri Code of State Regulations Title 4, Division 30. No person may make any modifications to thisThe Professional Engineer's seal and signature apply only to the document to which they are affixed. The Engineer expressly disclaims any responsibility for all other plans, specifications, estimates, reports or other documents or instruments relating to or intended to be used for any part of the engineering project.1098295011247electronic drawing file without the Engineers express written permission.2017 G&W Engineering Corp.277517-1271183139559-1271184396065-12711827011781363138679966513483397272630813440117234991WATERSTORAGEMECHANICALDNSEALREVISIONSPLAN NOTES - ELECTRICALEXISTING AMEREN MANHOLE.#1.2.NEW AMEREN GEAR SET ON PRECAST PAD.3.NEW AMEREN PAD MOUNT TRANSFORMER SET ON PRECAST PAD.4.NEW SECONDARY FEEDERS FROM TRANSFORMER TO NEW "MSB".JOB NO:5.NEW SECONDARY FEEDERS EXPOSED FROM FOUNDATION TO "MSB".DRAWN BY:6.ROUTE NEW PANEL "AC" FEEDERS TIGHT TO THE LOWER LEVEL CEILINGS.CHECKED BY:7.DATE:8.SHEET NO.9.NOTE: REFER TO ONE LINE DIAGRAM FOR ADDITIONAL INFORMATION.OVERALL PLAN - ELECTRICALHVAC UPGRADES TOKIPP: INSPIRE ACADEMY2017-0214.0009-25-2017MIDDLE SCHOOLJ.R.A.J.R.A.1212 N. 22ND STREET ST. LOUIS, MO 631069081437-8723652017-0214.00 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download