Student Reference - Houston Independent School District
Introduction To Automotive Technology
Automotive Technology
Module 1: Introduction to Automotive Technology
Student Reference
Technical
Consultants:
Ken Estes
Robin Ferguson
Steve Reese
Project
Coordinator:
Erica Kassel
Editor:
Janis Levsen
Produced by the Instructional Materials Laboratory
1400 Rock Quarry Center
University of Missouri-Columbia
Columbia, MO 65211
(800) 669-2465
2006 Edition
Catalog no. 70-1801-S
? 2006. The Curators of the University of Missouri.
All Rights Reserved.
Graphic
Artists:
Chris Benedict
Jacqueline Craig
Automotive Technology
ii
Introduction To Automotive Technology
ACKNOWLEDGMENTS
The 2006 revision of Introduction to Automotive Technology represents the
Instructional Materials Laboratory¡¯s commitment to the continual improvement
of the Automotive Technology Curriculum. Introduction to Automotive Technology
is the first in the nine-module series. The other modules are as follows:
Module 2
Module 3
Module 3
Module 3
Module 4
Module 5
Module 6
Module 7
Module 8
Module 9
Electrical Systems
Engine Performance, Section 1: Ignition Systems
Engine Performance, Section 2: Fuel and Exhaust Systems
Engine Performance, Section 3: Emission Control Systems
Engine Repair
Steering and Suspension Systems
Brakes
Manual Drive Train and Axles
Automatic Transmissions and Transaxles
Heating and Air Conditioning
All modules are based on the National Automotive Technicians Education
Foundation (NATEF) task list. For years the National Institute for Automotive
Service Excellence (ASE) has set the professional standards for automotive
technicians. A strong NATEF orientation makes the nine curriculum guides an
effective tool for preparing students to enter the technologically advanced field of
automotive technology.
IML gratefully acknowledges the important contribution of the advisory
committee:
Roger Donovan, Illinois Central College, East Peoria, IL
Ken Estes, Grand River Technical School, Chillicothe, MO
Robin Ferguson, Kirksville Vocational Technical School, Kirksville, MO
Sam Jeanrenaud, Lee¡¯s Summit, MO
Keith Kendrick, John A. Logan College, Carterville, IL
Steve Reese, Lewis and Clark Vocational Technical School, St. Charles, MO
Ron Tuetken, Lewis and Clark Community College, Godfrey, IL
John Walker, Hannibal Area Vocational Technical School, Hannibal, MO
Rodney Wolken, Eldon Career Center, Eldon, MO
iii
Automotive Technology
iv
Introduction To Automotive Technology
TABLE OF CONTENTS
Introduction ................................................................................................................. i
Title Page................................................................................................ i
Acknowledgments..............................................................................iii
Components........................................................................................vii
References..........................................................................................viii
Unit I
Careers in the Automotive Field...................................................S 1
Lesson 1: The Automotive Technology Career........................... S 5
Unit II
Safety................................................................................................S 11
Lesson 1: Protecting Yourself and Others in the Shop............. S 15
Lesson 2: Shop Safety Features and Emergency
Procedures....................................................................................... S 35
Lesson 3: Raising and Supporting Vehicles Safely................... S 41
Lesson 4: Federal and State Hazardous Material
Regulations...................................................................................... S 49
Unit III
Chemicals and Their Use.............................................................S 59
Lesson 1: Solvents, Soaps, and Cleaning Solutions.................. S 63
Lesson 2: Lubricants and Specialty Chemicals.......................... S 71
Lesson 3: Gases, Asbestos Dust, and Battery Acid................... S 79
Unit IV
Basic Hand Tools...........................................................................S 85
Lesson 1: Types of Wrenches....................................................... S 89
Lesson 2: Types of Screwdrivers and Pliers............................... S 97
Lesson 3: Types of Hammers, Punches, and Chisels.............. S 103
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- student reference houston independent school district
- an environmental guide for texas automotive repair shops
- wr w1 185 small engine parts jacks small engines
- concrete pump model c 30hd multiquip inc
- our distributor network united states
- rebuilt vehicle statement form vtr 61
- the power behind it all isuzu engines
- high performance ford modular enginetech catalog
- texas aerospace aviation company directory
- distributor s limited warranty
Related searches
- gadsden independent school district anthony nm
- gadsden independent school district nm
- gadsden independent school district homepage
- gadsden independent school district ho
- gadsden independent school district home
- gadsden independent school district website
- gadsden independent school district calendar
- gadsden independent school district address
- gadsden independent school district jobs
- galveston independent school district tx
- galveston independent school district website
- galveston independent school district jobs