CABIN ALTITUDE vs. CABIN PRESSURE DIFFERENTIAL …



CessnaOperational &MaintenanceProceduresCessna Aircraft Company680A (Citation Latitude)THIS GUIDE IS CURRENT WITH THE MASTER MINIMUM EQUIPMENT LIST WHICH IS DISTRIBUTED BY THE DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION - REVISION 01 DATED 08/01/2018.COPYRIGHT ? 2018MMEL REVISION 01CESSNA AIRCRAFT COMPANYWICHITA, KANSAS, U.S.P REVISION 06NOTICEThe Master Minimum Equipment List (MMEL) is distributed by the Department of Transportation Federal Aviation Administration. This Master Minimum Equipment List Operation and Maintenance Procedures manual contains only the items from the Master Minimum Equipment List which have Maintenance (M) or Operational (O) procedure requirements. Cessna does not support Minimum Equipment List items not published in the MMEL.Cessna’s policy is to revise this manual only to accommodate changes to a new MMEL revision, which requires a change to, or a new, Maintenance (M) or Operational (O) required procedure. If a revised MMEL is released, but does not affect any required procedure, the Operational and Maintenance manual will not be revised at that time. Cessna reserves the right to make format changes without generating a new revision.Maintenance (M) or Operational (O) procedures in this manual are recommended by Cessna Aircraft Company. Most of the procedures in this manual have been approved in some MEL’s. This document is not FAA approved, but is intended to aid operators in writing and gaining approval for their specific Minimum Equipment List (MEL). The Operator is responsible to make sure that all crew members are properly trained in the use of MEL (M) and (O) procedures.The Narrative section of each Maintenance (M) procedure is intended to satisfy the FAR 135 MEL requirement for training non-maintenance individuals who are authorized, in the MEL, to perform maintenance tasks.14 CFR 91 operators must have the following statement included in their COMPs Manual or operator produced Procedures Guide. All other operators must remove or delete the following statement.THIS DOCUMENT IS APPLICABLE TO PART 91 OPERATIONS ONLY AND MAY NOT BE USED FOR OPERATIONS CONDUCTED UNDER PARTS 121, 125, 129, OR 135.NOTESFor all provisos – Unless the proviso requires a system to be verified, it is assumed that all other systems are operative and no action is required to test these systems.Where ever a dash (-) is listed in Column 2: Number Installed or Column 3: Number Required for Dispatch, it is the responsibility of the operator to replace the dash (-) with the actual number of each item, if any, installed on the aircraft in question.The operator must make an appropriate entry in the discrepancy report for each inoperative item.The diagrams, drawings and/or pictures in this document may not reflect all possible installations. Refer to the aircraft equipment list, continuous history report and/or STC for current installed equipment.The Code of Federal Regulations (CFR), Title 14, Aeronautics and Space, listed in this document may not be up to date with the most current regulation. It is the responsibility of the operators to make sure all applicable 14 CFR parts are listed in their operational documents.The maintenance procedures in this document may be different than those found in the current revision of the Cessna Maintenance Manual for the associated aircraft model. In the event of conflict, use the more restrictive maintenance procedure to accomplish the task.PLACARDING REQUIREMENTSWhen relief is taken for an item listed in a MMEL or operator’s MEL, regulations require the operator to placard the item or system as inoperative or missing. The following guidelines are designed to assist operators with placarding inoperative or missing items or systems. Operators may develop alternate procedures for placarding inoperative or missing items or systems.Placards should be placed above, adjacent to or on the associated / affected control (annunciator, circuit breaker, switch, button, gauge, indicator, knob or light).Pre-manufactured “INOP” or “INOPERATIVE” placards may be used at the discretion of the operator.For missing items or systems, the placard should include text which specifies the component that is missing.If the inoperative item or system is not within view of the flight crew, an additional placard should be placed on the instrument panel in view of the flight crew. The placard should include text which specifies the component that is inoperative.If the relief for an item or system includes limitations on aircraft operations, an additional placard should be placed on the instrument panel in view of the flight crew. The placard should include text which states the limitation. If the limitation contracts a permanent placard installed in the cockpit as a part of the certified aircraft, the placard should be placed adjacent to the permanent placard. For example, a placard restricting VMO should be placed near the MAX OPERATING SPEED placard. Examples of common limitations on aircraft operations are:RVSM OPERATIONS ARE PROHIBITEDOPERATIONS IN IMC ARE PROHIBITEDFLIGHT INTO ICING IS PROHIBITEDOPERATIONS AT NIGHT ARE PROHIBITEDCARRIAGE OF CABIN OCCUPANTS IS PROHIBITEDCARRIAGE OF CARGO (EXCLUDING BALLAST) IS PROHIBITEDSINGLE-PILOT OPERATIONS ARE PROHIBITEDOPERATIONS ABOVE FL410 ARE PROHIBITEDFor indications shown on an electronic display, the placard should be placed adjacent to or on the bezel of the display and should include text which specifies the indication that is inoperative. The placard should NOT be placed on the display as this may obstruct the view of other indications in alternate or reversionary modes. This also applies to specific software functions or items within a system such as a Flight Management System (FMS) Navigation Database.Placards installed on equipment used by cabin passengers should include text such as “DO NOT USE” if the item or system is deactivated. For example, a vanity basin with an inoperative drain should include a placard stating “DO NOT POUR LIQUIDS INTO BASIN”. Make sure the placard can be easily understood by all passengers. Consider any passengers whose primary language is not the same as the placard’s language.Items or systems which have external access such as a baggage door or refueling panel should include a placard on the exterior side of the door or on the interior side provided it is prominently in view when accessed. The placard should include text specifying the item or system that is inoperative and / or states limitations on aircraft operations.Placard text should be of appropriate size, font and color so that it can be easily read. Placards placed on the exterior of the aircraft should be made of materials that will not degrade or depart the aircraft, such as aerodynamic tape and permanent marker.Placarding does NOT satisfy the requirement to make an appropriate entry in the discrepancy report for an inoperative or missing item or system.Regulatory ReferencesWhen an item’s proviso includes language such as “any in excess of those required by 14 CFR” or “not required by 14 CFR”, the operator is required to replace this reference with the specific operating requirement applicable to their operation. The following table lists 14 CFR references for certain systems. This table may include references for items not installed on this aircraft or which MMEL relief is not offered.ATAItemTitle14 CFR Reference(s)22-10-XXAutopilot SystemApp G23-00-XXSATCOM135.98, 135.16523-10-XXHigh Frequency (HF) Communication System 91.511, 135.98, 135.16523-11-XXUltra High Frequency (UHF) Communication System91.126, 91.127,91.129, 91.130,91.131, 91.135,91.205, 91.511,135.161, 135.16523-12-XXVery High Frequency (VHF) Communication System91.126, 91.127,91.129, 91.130,91.131, 91.135,91.205, 91.511,135.161, 135.16523-40-XXPassenger Address (PA) System135.15023-50-XXHeadsets91.511, 135.151, 135.16523-50-XXMicrophone91.511, 135.16523-70-XXCockpit Voice Recorder91.609, 91.1045, 135.15124-30-XXDC Generator135.16325-10-XXPassenger seat shoulder harness91.20525-20-XXUnder seat restraining bars91.52325-20-XXPassenger Briefing Cards91.519, 91.103525-20-XXTables91.53525-20-XXMovie Screens (In aisle)91.53525-20-XXObserver’s Seat135.7525-60-XXEmergency Medical Kit (EMK)25-60-XXFirst Aid Kit (FAK)91.51325-60-XXAutomatic External Defibrillator (AED)25-60-XXPyrotechnic Signaling Device91.205, 91.509, 135.16725-60-XXCrash Axe25-61-XXFlotation Device91.205, 91.509, 135.16725-62-XXEmergency Locator Transmitter (ELT) (Fixed, Automatic)91.20725-62-XXEmergency Locator Transmitter (ELT) (Survival)91.207, 91.509, 135.16725-64-XXLife Raft91.509, 135.16726-22-XXPortable Fire Extinguishers91.513, 135.15530-10-XXAnti-Ice System91.52730-30-XXPitot Heat135.163, App A30-40-XXWindshield WiperApp A31-20-XXClock91.20531-30-XXFlight Data Recorder91.609, 91.1045, 135.15233-20-XXPassenger Information Sign91.51733-40-XXWing Illumination Lights91.52733-40-XXAnti-Collision Light System91.205, 91.209, 135.15933-40-XXLanding Light91.205, 91.50733-40-XXPosition / Navigation Lights91.205, 91.20933-50-XXFlashlight91.503, 135.15934-11-XXStatic Pressure System135.163, App A34-12-XXFree Air Temperature Indicator135.16334-13-XXVertical Speed Indicator135.163, App A34-14-XXAirspeed Indicator91.205, App A,34-15-XXOverspeed Warning91.60334-16-XXAltitude Alerter91.219, App G34-16-XXAltimeter91.20534-16-XXSensitive Altimeter91.205, 135.149, App A34-17-XXAltitude Measurement SystemsApp G34-21-XXGyro Pitch and Bank91.205, 135.159, App A34-22-XXStandby Attitude Indicator135.14934-22-XXMagnetic Direction Indicator91.205, 135.159 34-22-XXGyro Direction Indicator91.609, 91.1045, 135.152, 135.15934-24-XXGyro Rate of Turn91.205, 135.15934-24-XXSlip-Skid Indicator91.205, 135.15934-25-XXFlight DirectorApp A34-31-XXInstrument Landing System (ILS)135.165, App A34-34-XXMarker Beacon135.165, App A34-42-XXWeather Radar System91.1045, 135.173, 135.17534-44-XXTerrain Awareness and Warning System91.223, 91.1045, 135.15434-44-XXRadio AltimeterApp A34-45-XXTraffic Alert and Collision Avoidance System (TCAS)91.221, 91.1045, 135.18034-46-XXThunderstorm Detection System91.1045, 135.17334-51-XXDistance Measuring Equipment (DME)91.205, 135.16534-52-XXATC Transponder and Automatic Altitude Reporting System91.130, 91.131, 91.135, 91.215,34-52-XXAutomatic Dependent Surveillance-Broadcast91.130, 91.131, 91.135, 91.225, 34-52-XXElementary and Enhanced Downlink Aircraft Reportable Parameters135.14334-52-XXADS-B Squitter Transmissions91.22734-54-XXVery High Frequency Omnirange (VOR) System91.131, 91.205, 91.511, 135.161, 135.16534-55-XXAutomatic Direction Finder (ADF)91.205, 135.16134-57-XX-60-XXLong-Range Navigation System91.131, 91.205, 91.511, 135.16535-10-XXFlight Crew Oxygen System91.211, 135.15735-20-XXPassenger Oxygen System91.211, 135.15735-30-XXPortable Breathing Equipment (PBE)37-20-XXVacuum Indicator135.16371-60-XXCarburetor Heat135.14977Engine Indications91.205Page Intentionally Left Blank21-21-04-01Recirculation Shutoff ValveC/1/0(M) May be inoperative provided valve is secured in the closed position.MAINTENANCE PROCEDURESecure valve in the closed position.Remove locking pin from its stowed position.Using a .50 in. wrench, rotate valve to the closed position.Install the locking pin into the LOCKED CLOSED position.21-30-01Cabin Dump Function(Unpressurized)C/1/0(M) May be inoperative provided:Outflow valve is removed, andCabin pressurization system is considered inoperative (Refer to item 21-30-02).MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 21, Air Conditioning - Dispatch Deviation.21-30-02-00ACabin Pressurization System(Unpressurized with cabin occupants)C/1/0(O) May be inoperative provided:PRESSURIZATION AUTO/MAN is selected to MANUAL,CABIN DUMP is selected to DUMP,Aircraft is operated at 13,500 feet cabin altitude or below, andFlight crew oxygen system is used as required by 14 CFR.NOTE: Amber CABIN ALTITUDE CAS message may appear at 8,500?feet cabin altitude. CABIN ALTITUDE red message may appear and CABIN ALTITUDE aural warning may sound at 9,650?feet cabin altitude.OPERATIONAL PROCEDUREFlight planning must consider the fuel burn and range associated with flight at lower altitudes.Minimum enroute altitudes must be taken into account for the planned route.Passengers must be briefed prior to each flight that cabin pressurization will be unavailable. Any medical complications or concerns must be considered in determination of the enroute altitude.Portable or therapeutic oxygen may be used as needed for passenger comfort.Cabin pressure must be monitored throughout the flight.21-30-02-00BCabin Pressurization System(Unpressurized without cabin occupants)C/1/0(M) (O) May be inoperative provided:PRESSURIZATION AUTO/MAN is selected to MANUAL,Emergency pressurization system is deactivated,CABIN DUMP is selected to DUMP,PASS OXY is selected OFF,No cabin occupants are carried,Aircraft is operated at FL250 or below, andFlight crew oxygen system is used as required by 14 CFR.NOTE: Amber CABIN ALTITUDE message may appear at 8,500?feet cabin altitude. CABIN ALTITUDE red message may appear and CABIN ALTITUDE aural warning may sound at 9,650?feet cabin altitude.MAINTENANCE PROCEDUREPull and secure the EMER PRESSURE circuit breaker on the copilot’s circuit breaker panel. OPERATIONAL PROCEDUREFlight planning must consider the fuel burn and range associated with flight at lower altitudes.Minimum enroute altitudes must be taken into account for the planned route.Cabin pressure must be monitored throughout the flight.21-30-03Emergency Pressurization System(Failed closed)C/1/0(M) May be inoperative provided:Emergency pressurization valve is secured closed,Aircraft is operated at FL250 or below.MAINTENANCE PROCEDUREVerify the emergency pressurization valve is closed.Pull and collar EMER PRESSURE circuit breaker on copilot’s circuit breaker panel.Using the Airplane Flight Manual, start both engines.Select PRESS SOURCE to EMER.Verify no airflow exists from the cabin floor ducting.Select PRESS SOURCE to NORM.21-32-01-00ACabin Altitude Gauge/Indication(Pressurized)C/1/0(O) May be inoperative provided:Cabin pressurization system automatic schedule mode is operative,Cabin differential pressure gauge/indication is operative, andA chart is provided to convert differential pressure and aircraft altitude to cabin altitude.OPERATIONAL PROCEDUREUse the chart in Appendix A to convert differential pressure and aircraft altitude to cabin altitude.21-32-02-00ACabin Differential Pressure Gauge/Indication(Pressurized)C/1/0(O) May be inoperative provided:Cabin altitude gauge/indication is operative,Cabin pressurization system automatic schedule mode is operative, andA chart is provided to convert cabin and aircraft altitude to differential pressure.OPERATIONAL PROCEDUREUse the chart in Appendix A to convert cabin and aircraft altitude to differential pressure.21-33-01Cabin Outflow ValveC/2/0(M) May be inoperative provided:Outflow valve is secured open, andCabin pressurization system is considered inoperative (Refer to item 21-30-02).MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 21, Air Conditioning - Dispatch Deviation.21-33-02-00APressure Regulating Valve(Mass Flow Control Valve)(Pressurized)C/2/1(M) One may be inoperative provided:Affected mass flow control valve is secured for no flow,PRESS SOURCE is selected to operative source, andAircraft is operated at FL410 or below.NOTE: Amber PRESS SRC NOT NORM message may appear.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 21, Air Conditioning - Dispatch Deviation.21-33-02-00BPressure Regulating Valve(Mass Flow Control Valve)(Unpressurized)C/2/0(M) May be inoperative provided:Both mass flow control valves are secured for no flow,PRESS SOURCE is selected OFF,BAG HEAT is selected OFF,Cockpit and cabin temperature control systems are considered inoperative (Refer to item 21-60-01), andCabin pressurization system is considered inoperative (Refer to item 21-30-02).NOTE: Amber PRESS SRC NOT NORM message may appear.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 21, Air Conditioning - Dispatch Deviation.21-50-01Air Cycle MachineC/1/0(O) May be inoperative provided:PRESS SOURCE is selected OFF,APU BLEED AIR is selected OFF,Both mass flow valves are verified closed,Cockpit and cabin temperature control systems are considered inoperative (Refer to item 21-60-01), andCabin pressurization system is considered inoperative (Refer to item 21-30-02).NOTE: Amber PRESS SRC NOT NORM message may appear.OPERATIONAL PROCEDUREStart the left and the right engines. Refer to the Model 680A Approved Airplane Flight Manual. The APU should remain OFF.Make sure that no warm air flows from the cabin warm air ducts or the overhead outlets with PRESS SOURCE SELECT selected OFF.21-62-01-01ATemperature Indication SystemCabin(With cabin occupants)C/1/0(O) May be inoperative provided alternate means are established and used to determine cabin temperature.OPERATIONAL PROCEDUREMake sure the cabin has been warmed to an acceptable temperature prior to flight. Refer to the Model 680A Approved Airplane Flight Manual. A portable temperature indicating device may be used to determine the temperature.22-10-01-01Autopilot Disconnect Button(AP/TRIM/NWS DISC)(Failed deselected)Left Control WheelB/1/0(O) May be inoperative provided:Right control wheel button is operative,Alternate procedures for disconnecting nose wheel steering during ground operations are established and used,Pilot remains seated in right seat with seat belt fastened during all autopilot operations,Autopilot system is not used below AFM cruise minimum use height, andApproach minimums do not require use of autopilot system.OPERATIONAL PROCEDUREThe flight crew must brief that during all aircraft ground movements (including takeoff and landing), the copilot will have control of the AP/TRIM/NWS DISC function so that, in the event of a system malfunction, the copilot will activate the disconnect and the pilot will maintain directional control of the aircraft using a combination of tiller wheel steering, differential braking and thrust.22-10-03Autopilot SystemB/1/0(M) May be inoperative provided:Autopilot system is deactivated,Yaw damper is considered inoperative (Refer to item 22-10-05),Enroute procedures and approach minimums do not require use of autopilot system,Cabin pressurization system is not operated in manual mode, andAircraft is not operated RVSM.MAINTENANCE PROCEDUREPull and secure the AUTOPILOT circuit breaker on the pilot’s circuit breaker panel.NOTE-1: Amber “DATA BUS FAIL” message may be displayed on the ground. NOTE-2: Providing “DATA BUS FAIL” message is not displayed prior to AUTOPILOT (HC073) circuit breaker pull, Aircraft is ok to for flight.22-10-05Yaw DamperB/1/0(M) May be inoperative provided:Yaw damper is deactivated, andAutopilot system is considered inoperative (Refer to item 22-10-03).MAINTENANCE PROCEDUREPull and secure the AUTOPILOT circuit breaker on the pilot’s circuit breaker panel.NOTE-1: Amber “DATA BUS FAIL” message may be displayed on the ground. NOTE-2: Providing “DATA BUS FAIL” message is not displayed prior to AUTOPILOT circuit breaker pull, Aircraft is ok to for flight.22-30-01Autothrottle SystemC/1/0(M) May be inoperative provided:Autothrottle system is deactivated, andProcedures do not require its use.MAINTENANCE PROCEDUREPull and secure the AUTO THROTTLE circuit breaker on the pilot’s circuit breaker panel.NOTE-1: Amber “DATA BUS FAIL” message may be displayed on the ground. NOTE-2: Providing “DATA BUS FAIL” message is not displayed prior to AUTO THROTTLE circuit breaker pull, Aircraft is ok to for flight.23-10-01-00BHigh Frequency (HF) Communications System(Dual LRCS required)C/-/1(O) May be inoperative while conducting operations which require two Long-Range Communication Systems (LRCS) provided:Aircraft SATVOICE system operates normally,SATVOICE services are available as a LRCS over intended route of flight,ICAO Flight Plan is updated, as required, to notify ATC of communications equipment status of aircraft, andAlternate procedures are established and used.OPERATIONAL PROCEDUREPrior to each flight, a crew member shall make sure that SATCOM Data Link and ACARS systems are operational for transmitting and receiving information from a ground station.Prior to each flight, a crew member shall review SATCOM system user’s guide/manual to ensure coverage exists for the intended route of flight.Prior to flight, a crew member shall coordinate with the appropriate ATC facility to advise of intended flight without INMARSAT codes, if codes are not available.23-20-01-02BSatellite Datalink ServiceWeatherC/-/0(O) May be inoperative provided alternate procedures are established and used.OPERATIONAL PROCEDURECrew shall use other available means to obtain weather information such as HIWAS or FLIGHTWATCH as well as radar.23-20-03-00BSelective Call (SELCAL)(System or individual channel)C/-/0(O) May be inoperative provided alternate procedures are established and used.OPERATIONAL PROCEDUREFlight crew must advise ATC of inoperative SELCAL, as appropriate.Flight crew will monitor the appropriate radios at all times in the absence of SELCAL. Consideration should be given to the effect of increased fatigue due to this requirement and the possibility of having only one crew member monitor the radios via headset (especially HF) if required for the given flight.23-40-02Crewmember Interphone System (Flight Deck to Ground)C/1/0(O) May be inoperative provided alternate procedures are established and used.OPERATIONAL PROCEDUREAlternate procedures for communication with ground crew must be established and used.23-40-03Passenger Address (PA) SystemC/1/0(O)May be inoperative provided:PA not required by 14?CFR, andAlternate, normal and emergency procedures, and/or operating restrictions are established and used.Note: Any station function(s) that operate normally may be used.OPERATIONAL PROCEDUREAlternate procedures for passenger announcements must be established and used.23-40-04Passenger Seat Belt / Safety ChimeC/1/0(O) May be inoperative provided:Passenger address system is operative, andCabin occupants are briefed by alternate means.OPERATIONAL PROCEDUREA crew member must use the PA system from the cockpit to make the appropriate announcements.23-50-04-02Cockpit Hand MicrophoneHolderD/-/0(O) May be inoperative provided associated hand microphone is secured by alternate means.OPERATIONAL PROCEDUREPrior to flight, a crew member must ensure that the hand micro phone is secured in a manner that will not interfere with aircraft operations. One method is to utilize adhesive hook and loop (Velcro) strips on the pedestal.23-50-07-01Push-to-talk (PTT) SwitchYoke SwitchB/2/1(O) One may be inoperative provided alternate procedures are established and used for transmitting.OPERATIONAL PROCEDUREPrior to flight, the crew member with the operative switch will be assigned all radio transmissions.24-60-03Interior DisconnectC/1/0(M) (O) May be inoperative provided:Interior power system is deactivated, Cabin emergency lighting is verified operative, andPassengers are briefed on disabled cabin electrical systems or are not carried.NOTE: Items powered by interior bus are considered inoperative. This includes, but is not limited to: Cabin interior lighting, cabin window shade system, galley appliances, galley drain, vanity drain, forward equipment fan, aft equipment fan, cabin AC inverter, and cabin entertainment system.MAINTENANCE PROCEDUREPull the LEFT INTERIOR FEED BUS fuse in the LH power junction box and the RIGHT INTERIOR FEED BUS fuse in the RH power junction box.OPERATIONAL PROCEDUREWith both batteries off and no generators running, select EMER LTS to ON.Quickly verify the EXIT signs and the aisle lighting near the main cabin door is operative.Select EMER LTS to OFF.25-00-01Required Documents Holder(Airworthiness Certificate, Registration, etc.)D/1/0(O) May be missing or inoperative provided an alternate means of securing and displaying required documents is used.OPERATIONAL PROCEDUREPlace the required documents in a clear plastic bag and display them in a manner that is visible to the appropriate authorities, crew members and passengers.25-10-02Cockpit CurtainD/-/0(M) May be missing, or inoperative provided curtain is secured open.MAINTENANCE PROCEDURECarefully attach sufficient lengths of 3M vinyl tape (or equivalent) around the cockpit curtain and from the cockpit curtain to adjacent interior components to make sure that the cockpit curtain does not close or become loose during airplane operation.25-10-05-01BFlight Crew Seat(Per seat)ArmrestC/2/0(M) May be missing, or inoperative provided affected armrest is removed.MAINTENANCE PROCEDUREUsing the appropriate seat manual, remove and store the affected armrest(s).NOTE:Refer to the appropriate Cessna Maintenance Manual and/or seat manual for information of the individual aircraft installation.25-10-05-03Flight Crew Seat(Per seat)Recline/Tilt FunctionC/2/0(M) (O) May be inoperative provided:Affected seat is secured or failed in a position that permits normal visibilty,Full flight control movement is available, andCrewmember can reach all necessary controls and equipment while restrained.MAINTENANCE PROCEDUREUsing the appropriate seat manual, secure the seat in the desired position.NOTE:Refer to the appropriate Cessna Maintenance Manual and/or seat manual for information of the individual aircraft installation.OPERATIONAL PROCEDUREPrior to flight, a crew member shall occupy the affected seat and fasten the restraining system.Make sure full flight control movement and brake application are available.Make sure all necessary controls and equipment can be reached.25-10-05-06Flight Crew Seat(per seat)Vertical AdjustmentD/1/0(M) (O) May be inoperative provided:Affected seat is secured or failed in a position that permits pilot normal visibility,Full flight control movement is available, andCrewmember can reach all necessary controls and equipment while restrained.MAINTENANCE PROCEDUREUsing the appropriate seat manual, secure the seat in the desired position.NOTE:Refer to the appropriate Cessna Maintenance Manual and/or seat manual for information of the individual aircraft installation.OPERATIONAL PROCEDUREPrior to flight, a crew member shall occupy the affected seat and fasten the restraining system.Make sure full flight control movement and brake application are available.Make sure all necessary controls and equipment can be reached.25-10-08Eye Reference BallC/3/0(O) May be inoperative or missing provided alternate procedures are established and used for eye position reference.OPERATIONAL PROCEDUREPrior to flight, a crew member shall occupy the affected seat and fasten the restraining system to ensure the following conditions are met:Make sure full flight control movement and brake application.Make sure access to all necessary controls and equipment.Position the affected seat(s) so the pilot align the eyeball locator bracket so that the following sight picture with the bracket is achieved:Eyeball locator base is flat.The flange opposite to the affected seat is aligned for a straight edge.25-20-03Cabin CurtainD/-/0(M) May be missing, or inoperative provided curtain is secured open.MAINTENANCE PROCEDURECarefully attach sufficient lengths of 3M vinyl tape (or equivalent) around the cockpit curtain and from the cockpit curtain to adjacent interior components to make sure that the cockpit curtain does not close or become loose during airplane operation.25-20-06-02APassenger Seat(Including side-facing seats, folding seats and couches)(Per seat)Seat Controls (Includes recline, headrest, footrest, floor tracking, pedestal tracking,swivel, and other positioning controls)D/-/0(M) May be inoperative with seat occupied provided seat is secured in taxi, takeoff and landing position.MAINTENANCE PROCEDUREUsing the appropriate seat manual, secure the seat in the full upright position.NOTE:Refer to the appropriate Cessna Maintenance Manual and/or Interiors Manual for information of the individual aircraft installation.25-30-01Refreshment Center Hot Liquid Storage System HeaterD/-/0(M) May be inoperative provided system is deactivated.MAINTENANCE PROCEDUREAccess the appropriate junction box.Pull and secure the appropriate circuit breaker.NOTE:Refer to the appropriate Interiors Manual for information of the individual aircraft installation.25-30-02Refreshment Center Microwave / OvenD/1/0(M) May be inoperative provided system is deactivated.MAINTENANCE PROCEDUREAccess the appropriate junction box.Pull and secure the appropriate circuit breaker.NOTE:Refer to the appropriate Interiors Manual for information of the individual aircraft installation.25-40-02Aft Vanity Hot Liquid Storage System HeaterD/1/0(M) May be inoperative provided system is deactivated.MAINTENANCE PROCEDUREAccess the appropriate junction box.Pull and secure the appropriate circuit breaker.NOTE:Refer to the appropriate Interiors Manual for information of the individual aircraft installation.25-50-01-01BBaggage Restraint SystemAnchor PlateC/-/0(M) Individual anchor plates may be inoperative provided:Attaching structure is inspected for damage, andBaggage is secured using remaining anchor plates or not carried.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 25, Equipment/Furnishings - Dispatch Deviation.25-50-02-00ACabin Storage CompartmentC/-/-(M) May be inoperative provided:Compartment does not contain any aircraft system protection devices,Any emergency equipment located in affected compartment is considered inoperative,Affected compartment is not used for storage of any item except for those permanently affixed,Procedures are established and used to secure compartment closed, andAffected compartment is prominently placarded "DO NOT USE".MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 25, Equipment/Furnishings - Dispatch Deviation.25-50-02-00BCabin Storage CompartmentC/-/0(M) May be inoperative provided:Affected door is removed,Affected compartment is not used for storage of any item, including those permanently affixed,Cabin occupants are briefed that affected compartment may not be used, andAffected compartment is prominently placarded “DO NOT USE”.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 25, Equipment/Furnishings - Dispatch Deviation. 25-50-02-01Cabin Storage CompartmentShelvingC/-/0(O) May be inoperative provided:Any permanently affixed emergency equipment located on affected shelf is relocated and available for use, andCabin occupants are briefed on location of relocated equipment.OPERATIONAL PROCEDUREMake sure all equipment located on affected shelf has been relocated and is available for use.Brief cabin occupants on location of relocated equipment.25-62-01-02AEmergency Locator Transmitter (ELT)Fixed, AutomaticA/-/0(M) May be inoperative provided:System is deactivated or removed, andRepairs are made within 90 calendar days.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 25, Equipment/Furnishings - Dispatch Deviation.25-62-01-02BEmergency Locator Transmitter (ELT)Fixed, AutomaticD/-/-(M) Any in excess of those required by 14 CFR may be inoperative provided system is deactivated or removed.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 25, Equipment/Furnishings - Dispatch Deviation.26-13-01-02Bleed Leak Detection System(Failed to pass preflight test)Horizontal StabilizerB/1/0(M) May be inoperative provided:Both ANTI-ICE ENGINE/STAB switches are selected OFF,Both stabilizer anti-ice valves are verified closed, andAircraft is not operated in known, forecast, or AFM-defined icing conditions.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 26, Fire Protection - Dispatch Deviation.26-13-01-03Bleed Leak Detection System(Failed to pass preflight test)WingB/2/0(O) May be inoperative provided:Both ANTI-ICE ENGINE/STAB switches are selected OFF,Both ANTI-ICE WING switches are selected OFF,Both wing anti-ice valves are verified closed, andAircraft is not operated in known, forecast, or AFM-defined icing conditions.OPERATIONAL PROCEDUREOn the ground, with engines running and bleed air ON, select both ANTI-ICE WING switches ON.With engines set slightly above idle, verify no airflow at the wing outboard anti-ice air outlets on both wings.27-20-01Rudder Pedal Adjustment SystemB/4/2(M) (O) Two may be inoperative provided:Two pedal adjustments are not inoperative at same pilot station,Affected pedal is positioned in a detent and adjustment mechanism is secured from movement,Unaffected pedal is adjusted to match affected pedal, andCrewmember seated at affected station verifies full control movement and brake application is available while restrained, prior to each flight.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 27, Flight Controls - Dispatch Deviation.OPERATIONAL PROCEDUREPrior to flight, a crew member shall occupy the affected seat and fasten the restraining system.Make sure full flight control movement and brake application are available.27-70-02Control / Gust Lock System(Failed unlocked)C/1/0(O) May be inoperative provided pilot verifies full flight control and throttle movement.OPERATIONAL PROCEDUREDuring the flight control check in the Before Taxi checklist, verify both throttles can be moved freely.28-41-01Fuel Low Level Indicating SystemA/2/1(O) One may be inoperative provided:Procedures for monitoring fuel quantity are established and used,Both fuel quantity indicating systems are operative, andRepairs are made within three flight days.OPERATIONAL PROCEDUREFlight crew shall brief the loss of low fuel quantity warning system on the affected side.Flight crew shall monitor fuel balance during flight to make sure adequate fuel remains in both wing fuel tanks for planned mission.28-41-02Fuel Quantity Indicating System(Wing Tank)A/2/1(O) One may be inoperative provided:Both fuel low level indicating systems and both fuel flow indicating systems are operative,Fuel required for route to be flown is increased by 10%,Flight is restricted to a maximum of three hours, remaining within one hour of a suitable airport at all points along route,Both fuel tanks are fueled over-wing to a known, balanced quantity,APU use is limited to thirty cumulative minutes if RH indicator is inoperative,Fuel use is tracked,If autopilot is used, it is disconnected every twenty minutes to detect possible lateral fuel imbalance, monitor trim required and RETRIM L-R WING DOWN amber message, andRepairs are made within three flight cycles.OPERATIONAL PROCEDUREDuring preflight planning, increase the fuel required for the route to be flown by 10%. Also plan the route so that the flight will last no longer than three hours while remaining within one hour of a suitable airport at all points.To achieve a known quantity in the affected tank, the tank may be emptied using Single-Point defueling then fueled to a known quantity. It may be completely fueled, or fuel may be transferred out of the tank until it is empty.To track fuel use, operators may use a fuel log or develop their own procedure. This can include matched fuel flow techniques, use of the FMS fuel quantity system or other means.During flight, disconnect the autopilot every twenty minutes. Make sure a crew member has control of the aircraft prior to disconnecting the autopilot. Check for any abnormal roll tendencies. Check for roll trim required.Re-engage the autopilot. Monitor the RETRIM L or R WING DOWN amber message.30-10-02Horizontal Stabilizer Bleed Air Anti-Ice System(Failed open)C/2/1(M) One may be inoperative provided:Affected horizontal stabilizer valve is secured for no flow,Affected ANTI-ICE ENGINE/STAB switch is selected OFF, andAircraft is not operated in known, forecast, or AFM-defined icing conditions.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 30, Ice and Rain Protection - Dispatch Deviation.30-10-04-01Wing Bleed Air Anti-Ice SystemInboard Leading EdgeA/2/0(M) May be inoperative provided:Both inboard wing valves are secured for no flow,Both ANTI-ICE ENGINE/STAB switches are selected OFF,Aircraft is not operated in known, forecast, or AFM-defined icing condition, andRepairs are made within three flight days.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 30, Ice and Rain Protection - Dispatch Deviation.30-10-04-02Wing Bleed Air Anti-Ice SystemOutboard Leading EdgeC/2/0(M) May be inoperative provided:Both outboard wing valves are secured for no flow,Both ANTI-ICE WING switches are selected OFF, andAircraft is not operated in known, forecast, or AFM-defined icing conditions.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 30, Ice and Rain Protection - Dispatch Deviation.30-20-01Engine Anti-Ice SystemA/2/1(M) One may be inoperative provided:Affected valve is secured for no flow,Affected ANTI-ICE ENGINE/STAB switches are selected OFF,Aircraft is not operated in known, forecast, or AFM-defined icing conditions, andRepairs are made within three flight days.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 30, Ice and Rain Protection - Dispatch Deviation.30-40-02Windshield Electric Anti-Ice SystemC/2/1(M) One may be inoperative provided:Affected windshield anti-ice system is deactivated,A means to clear windshield of moisture is readily available,Opposite side frost pane defog is considered inop(Refer to 30-40-05), andAircraft is not operated in known, forecast, or AFM-defined icing conditions.NOTE: Amber TRU FAIL message may be displayed.MAINTENANCE PROCEDUREPull and secure the L W/S ANTI-ICE circuit breaker on the pilot’s circuit breaker panel or the R W/S ANTI-ICE circuit breaker on the copilot’s circuit breaker panel.NOTE: Amber TRU FAIL message may be displayed.30-70-01Drain Heater(Refreshment center and aft vanity basin)C/-/0(M) May be inoperative provided:Drain heaters are deactivated,Refreshment center and aft vanity basin overboard drains are considered inoperative (Refer to item 38-30-04), andExternal lavatory service system heater gasket is considered inoperative (Refer to item 38-30-02-08).MAINTENANCE PROCEDUREPull and secure the DRAIN HEATERS circuit breaker on the aft interior junction box.31-10-02-02Panel Switch Lights(Failed to illuminate)Anti-Collision Lights(ANTI-COLL - ON)C/1/0(O) May be inoperative provided anti-collision lights (strobes) are visually verified on prior to each flight.OPERATIONAL PROCEDUREDuring the Cockpit/Cabin Inspection: Exterior Lights procedure, press the ANTI-COLL switch.Visually verify the anti-collision lights illuminate.Press the switch again, verify the lights extinguish.31-10-02-03Panel Switch Lights(Failed to illuminate)Anti- Ice Crossflow(WING XFLOW - XFLOW / OFF)C/2/0(O) May be inoperative provided:Switch functionality is verified operative, andA/I WING XFLOW OPEN white and amber messages are monitored.OPERATIONAL PROCEDUREDuring the Before Takeoff: Anti-Ice Systems procedure, press the WING XFLOW switch.Verify the A/I WING XFLOW OPEN white message appears.Press the switch again, verify the message(s) extinguishes.31-10-02-04Panel Switch Lights(Failed to illuminate)APU Bleed Air(APU BLEED AIR - ON / OFF)C/2/0(O) May be inoperative provided:Switch functionality is verified operative, andAPU BLD VALVE OPEN amber message and APU BLD VALVE CLOSED white message are monitored.OPERATIONAL PROCEDUREFollowing the Cockpit Preparation: APU start procedure, press the APU BLEED AIR switch.Verify the APU BLD VALVE CLOSE white message extinguishes.Press the switch again, verify the message appears.31-10-02-14Panel Switch Lights(Failed to illuminate)Auxiliary Hydraulic Pump(HYDRAULIC PUMP AUX - ON / OFF)C/2/0(O) May be inoperative provided switch functionality is verified operative.NOTE: Use HYD AUX PUMP ON white message to verify switch position.OPERATIONAL PROCEDUREDuring the Before Start procedure, press the HYDRAULIC PUMP AUX switch.Verify the AUX HYDRAULIC PUMP ON white message appears.Press the switch again, verify the message(s) extinguishes.31-10-02-23Panel Switch Lights(Failed to illuminate)Display Reversion(DISPLAY REV - NORM / REV)C/2/0(O) May be inoperative provided switch functionality is verified operative.OPERATIONAL PROCEDUREWith avionics on, press the affected DISPLAY REV switch.Verify the associated PFD and MFD enter reversionary mode.Press the DISPLAY REV switch again.Verify the associated PFD and MFD return to normal mode.31-10-02-27Panel Switch Lights(Failed to illuminate)Engine / Stabilizer Anti-Ice(ENGINE/STAB - ON / OFF)C/4/0(O) May be inoperative provided switch functionality is verified operative.NOTE: Use ANTI-ICE ON ENG/STAB white message to verify switch position.OPERATIONAL PROCEDUREDuring the Before Takeoff: Anti-Ice Systems procedure, press the affected ENGINE/STAB switch.Verify the associated ANTI-ICE ON ENG/STAB and/or A/I ENGINE COLD white messages appear.Press the switch again, verify the message(s) extinguishes.31-10-02-32Panel Switch Lights(Failed to illuminate)Fuel Boost(BOOST PUMP - NORM / ON)C/4/0(O) May be inoperative provided switch functionality is verified operative.NOTE: Use FUEL BST PUMP ON L-R white and amber messages to verify switch position.OPERATIONAL PROCEDUREFollowing engine start, press the affected BOOST PUMP button.Verify the associated FUEL BST PUMP ON L-R white message appears.Press the switch again.Verify the message extinguishes.31-10-02-35Panel Switch Lights(Failed to illuminate)Interior Power(INTERIOR - ON)C/1/0(O) May be inoperative provided switch functionality is verified operative.OPERATIONAL PROCEDUREWith main DC power active, press the INTERIOR button.Verify the OFF annunciator illuminates.Verify items on the INTERIOR bus, such as downwash lighting, are inoperative.Press the INTERIOR button again.Verify the OFF annunciator extinguishes.Verify the same interior items are now operative.31-10-02-37Panel Switch Lights(Failed to illuminate)Max Cool(MAX COOL – OFF)C/1/0(O) May be inoperative provided switch functionality is verified operative.NOTE: Use MAX COOL – ON switch light to verify switch position.OPERATIONAL PROCEDUREFollowing the Cockpit Preparation: APU start procedure, press the MAX COOL switch.Verify the operative MAX COOL ON switch light illuminates.Press the switch again, verify the switch light extinguishes.31-10-02-41Panel Switch Lights(Failed to illuminate)Pitot / Static Anti-Ice(PITOT/STATIC - ON / OFF)B/4/0(O) May be inoperative provided:Switch functionality is verified operative, andP/S COLD L-R-STBY white and amber messages are monitored.OPERATIONAL PROCEDUREDuring the Cockpit/Cabin Inspection: Anti-Ice PITOT/STATIC check, press the affected PITOT/STATIC switch.Externally verify the associated pitot and static heaters are heating.Verify the associated P/S COLD L-R-STBY white message appears briefly and then extinguishes.31-10-02-53Panel Switch Lights(Failed to illuminate)Wing Anti-Ice(WING - ON / OFF)C/4/0O) May be inoperative provided:Switch functionality is verified operative, andA/I WING COLD L-R white and amber messages are monitored.OPERATIONAL PROCEDUREDuring the Before Takeoff: Anti-Ice Systems procedure, press the affected WING switch and both ENGINE/STAB switches.Verify the ANTI-ICE ON ALL white messages appears and/or associated A/I WING COLD white message appears briefly.Press the switch again, verify the message(s) extinguishes.31-10-02-54Panel Switch Lights(Failed to illuminate)Wing Inspection Light(WING INSP - ON)C/1/0(O) May be inoperative provided:Switch functionality is verified operative, andWing inspection lights are visually monitored.OPERATIONAL PROCEDUREDuring the Cockpit/Cabin Inspection: Exterior Lights procedure, press the WING INSP switch.Visually verify the wing inspection lights illuminate.Press the switch again, verify the lights extinguish.31-20-01APU Hour MeterC/1/0(O) May be inoperative provided APU operation time is tracked by alternate means.OPERATIONAL PROCEDURELog elapsed time of APU in aircraft logbook after each flight. This includes ground operation times during any maintenance performed when the aircraft is not intended to fly.Once the APU hour meter is repaired, place a placard next to the hour meter showing the additional time accumulated while inoperative (e.g. “+ 14.2 hours”).31-20-04Flight Hour MeterC/1/0(O) May be inoperative provided flight time is tracked by alternate means.OPERATIONAL PROCEDURERecord Zulu time of takeoff and landing.Log elapsed time in aircraft logbook after each flight.Once the flight hour meter is repaired, place a placard next to the hour meter showing the additional time accumulated while inoperative (e.g. “+ 14.2 hours”).31-50-06-07WHITE CAS MESSAGE(Displayed)NO STANDBY DATAA/1/0O) May be displayed provided repairs are completed within ten flight days.OPERATIONAL PROCEDURECrew must manually compare displayed Data.31-50-06-08WHITE CAS MESSAGE(Displayed) OIL FILTER BYPASSA/1/0(O) May be displayed provided:ENG CHIP DETECT L or R is not displayed,Engine oil pressure and temperature are monitored, andRepairs are made within 10 operating hours.OPERATIONAL PROCEDUREDuring operation the flight crew must:Monitor ENG CHIP DETECT L or R is not displayed, andMonitor Engine oil pressure and temperature.31-50-06-09WHITE CAS MESSAGE(Displayed) OIL LEVEL LOW L or RA/1/0(O) May be displayed provided:Engine oil level is verified above MIN, andRepairs are made within 3 flight days.OPERATIONAL PROCEDUREDuring preflight walk around, a flight crewmember must visually verify the oil level is above minimum.33-10-05-00AWindshield Ice Detection LightC/2/1(O) One may be inoperative provided alternate procedures are established and used to monitor ice accretion.OPERATIONAL PROCEDUREThe flight crew member with the operative light must be assigned responsibility for monitoring the windshield for ice accumulation and alerted the other flight crew member. 33-20-02-00ACabin Interior Lighting(Excluding cabin emergency lighting)D/-/-(O) Individual lights may be inoperative provided:Sufficient lighting is operative for crew to perform required duties,Cabin emergency lighting is verified operative, andSufficient lighting is operative for carrying cabin occupants at night.OPERATIONAL PROCEDUREWith both batteries off and no generators running, select EMER LTS to ON.Quickly verify the EXIT signs and the aisle lighting near the main cabin door is operative.Select EMER LTS to OFF.33-20-02-00BCabin Interior Lighting(Excluding cabin emergency lighting)D/-/0(O) May be inoperative provided:Cabin emergency lighting is verified operative, andAircraft is not operated at night or cabin occupants are not carried.OPERATIONAL PROCEDUREWith both batteries off and no generators running, select EMER LTS to ON.Quickly verify the EXIT signs and the aisle lighting near the main cabin door is operative.Select EMER LTS to OFF.33-20-04-00ALighted Passenger Information Sign(Excluding cabin exit signs)(With cabin occupants)C/-/0(O) May be inoperative provided alternate procedures are established and used to notify cabin occupants.OPERATIONAL PROCEDUREA crew member will use the PA system or turn and face the cabin occupants to make appropriate announcements.33-40-03-01Landing LightRecognition Light ModeC/1/0(O) May be inoperative provided at least one landing light is verified operative for night operations.OPERATIONAL PROCEDUREDuring the Preliminary Exterior Inspection, verify at least one landing light is operative.33-40-03-02Landing LightPulse Light ModeD/1/0(O) May be inoperative provided at least one landing light is verified operative for night operations.OPERATIONAL PROCEDUREDuring the Preliminary Exterior Inspection, verify at least one landing light is operative.33-50-03Emergency Lighting Battery(CBS 28)(Excluding Pack 1 UF004)B/3/0(O) May be inoperative provided:Main cabin door exit signs are verified operative,Left forward dropped-aisle lighting is verified operative,Exterior emergency lights are considered inoperative (Refer to item 33-50-04).No cabin occupants are carried, andAircraft is not operated at night.OPERATIONAL PROCEDUREWith both batteries off and no generators running, select EMER LTS to ON.Quickly verify the main cabin door EXIT signs and the left forward aisle lighting is operative.Select EMER LTS to OFF.34-16-01Altitude Alerting SystemA/-/0(O) May be inoperative provided:Autopilot with altitude hold and capture operates normally,Aircraft does not depart from an airport where repair or replacement can be made,Aircraft is not operated RVSM, andRepairs are made within three flight days.OPERATIONAL PROCEDURECrew briefings must include a reminder that the Altitude Alerting System is inoperative.The flight crew will use aural callouts pertaining to approach target altitudes as assigned by ATC or depicted on approach charts.34-25-07Touchscreen Controller(GTC)(L PFD or R PFD)C/2/1(M) One may be inoperative provided controller is deactivated. NOTE: Any functions or controls that operate normally may be used.MAINTENANCE PROCEDUREPull and secure the L PFD GTC circuit breaker on the pilot’s circuit breaker panel or the R PFD GTC circuit breaker on the copilot’s circuit breaker panel.NOTE-1: Amber “DATA BUS FAIL” message may be displayed on the ground. NOTE-2: Providing “DATA BUS FAIL” message is not displayed prior to PFD circuit breaker pull, Aircraft is ok to for flight.34-36-01Reactive Windshear System(Includes TAWS windshear mode)C/1/0(O) May be inoperative provided alternate procedures are established and used.OPERATIONAL PROCEDURECrew briefings must include escape procedures for a windshear encounter and alternate methods used for monitoring for windshear encounters.34-44-01-00BRadio Altimeter System(TAWS or TCAS II required)A/1/0(M) May be inoperative provided:Radio altimeter system is deactivated,Approach minimums or operating procedures do not require its use,Basic TAWS modes are considered inoperative (Refer to item 34-40-03),TCAS II is considered inoperative (Refer to item 34-45-01), andRepairs are made within two flight days.NOTE 1: Landing gear warning system will function differently without radio altimeter input. Landing gear warning may occur at higher altitudes above ground with flaps extended.NOTE 2: Landing Operations Phase Inhibit (LOPI) operation will be affected. LOPI will not activate during approach or go-around.MAINTENANCE PROCEDUREPull and secure the appropriate circuit breaker.34-44-03Terrain Awareness and Warning System (TAWS)(Includes test mode)(Class A or B TAWS required)A/1/0(O) May be inoperative provided:Alternate procedures are established and used,RNP AR procedures are not conducted, andRepairs are made within two flight days.OPERATIONAL PROCEDURECrew briefings must include aural callouts through use of appropriate aircraft equipment to ensure obstacle and terrain clearance.34-44-03-01Terrain Awareness and Warning System (TAWS)Forward Looking Terrain Avoidance Function and Premature Descent Alert FunctionB/2/0(O) May be inoperative provided alternate procedures are established and used.OPERATIONAL PROCEDURECrew briefings must include aural callouts through use of appropriate aircraft equipment to ensure obstacle and terrain clearance.34-44-03-02Terrain Awareness and Warning System (TAWS)Excessive Rate of Descent (Mode 1) andAltitude Loss After Takeoff or Missed Approach (Mode 3)A/2/0(O) May be inoperative provided:Alternate procedures are established and used, andRepairs are made within two flight days.OPERATIONAL PROCEDURECrew briefings must include aural callouts through use of appropriate aircraft equipment to ensure obstacle and terrain clearance.34-44-03-03ATerrain Awareness and Warning System (TAWS)Voice Callouts (Mode 6)(“Five-Hundred”)B/1/0(O) May be inoperative provided alternate procedures are established and used.OPERATIONAL PROCEDURECrew briefings must include aural callouts during approach through the use of appropriate aircraft equipment to ensure obstacle and terrain clearance. Briefing must include a procedure for a crew member to call out 500 feet above airport elevation.34-44-03-03BTerrain Awareness and Warning System (TAWS)Voice Callouts (Mode 6)(Other)C/-/0(O) May be inoperative provided alternate procedures are established and used.OPERATIONAL PROCEDURECrew briefings must include aural callouts during approach through the use of appropriate aircraft equipment to ensure obstacle and terrain clearance. Briefing must include MDA or DH and a procedure for a crew member to call out 500 feet above airport elevation, plus any other agreed upon by the flight crew.34-44-03-04ATerrain Awareness and Warning System (TAWS)Excessive Closure Rate to Terrain (Mode 2) and Flight Into TerrainNot in Landing Configuration (Mode 4)(Class A TAWS required)A/2/0(O) May be inoperative provided:Alternate procedures are established and used, andRepairs are made within two flight days.OPERATIONAL PROCEDURECrew briefings must include aural callouts through use of appropriate aircraft equipment to ensure obstacle and terrain clearance.34-45-01-00ATraffic Alert and Collision Avoidance System (TCAS II)(TCAS not required)B/1/0(M) May be inoperative provided:System is deactivated,System is not required by 14 CFR, andEnroute or approach procedures do not require its use.MAINTENANCE PROCEDUREPull and secure the TCAS circuit breaker on the pilot’s circuit breaker panel.34-45-01-00BTraffic Alert and Collision Avoidance System(TCAS II)(TCAS required)C/1/0(M) May be inoperative provided:System is deactivated, andEnroute or approach procedures do not require its use.MAINTENANCE PROCEDUREPull and secure the TCAS circuit breaker on the pilot’s circuit breaker panel.34-45-01-01Traffic Alert and Collision Avoidance System(TCAS II)Traffic Advisory (TA) DisplayC/-/0(O) May be inoperative provided:Resolution Advisory (RA) display and audio function are operative, andEnroute or approach procedures do not require use of TCAS.OPERATIONAL PROCEDURE:Using test function, confirm that RA display elements (including VSI “fly to” and “do not fly” areas) and voice command audio functions are operative.Monitor PFD VSI for RA commands.34-45-01-02BTraffic Alert and Collision Avoidance System(TCAS II)Resolution Advisory (RA) DisplayC/2/0(O) May be inoperative provided:Traffic Advisory (TA) display and audio function are operative,TA-only mode is selected on TCAS controller or menu, andEnroute or approach procedures do not require use of TCAS.OPERATIONAL PROCEDURE:Using test function, confirm that Traffic Advisory display elements and voice command audio functions are operative.Select TA only mode of operation.34-61-01Navigation DatabaseC/-/-(O) May be out of currency provided:Current aeronautical charts are used to verify navigation fixes prior to each flight,Procedures are established and used to verify status and suitability of navigation facilities used to define route of flight, andApproach navigation radios are manually tuned and identified.OPERATIONAL PROCEDUREThe navigation database can only be used for enroute and terminal navigation when out of currency. Before using the FMS to navigate to a facility, verify the status, identifier, frequency and lat/long position with an alternate, current source of information. Refer to the applicable Airplane Flight Manual supplement for additional information. 35-00-03-01Oxygen SystemFill PortC/-/0(M) May be inoperative provided bottle is filled using alternate means, if service is required.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 35, Oxygen - Dispatch Deviation.35-00-03-02Oxygen SystemServicing Panel Pressure GaugeC/-/0(M) May be inoperative provided bottle is filled using alternate means, if service is required.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 35, Oxygen - Dispatch Deviation.35-20-01-01Passenger Oxygen SystemMaskC/-/0(M) Individual oxygen masks or dispensers may be inoperative or missing provided:Affected mask pintle pin is installed, andAssociated seat or lavatory is placarded "DO NOT OCCUPY".MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 35, Oxygen - Dispatch Deviation.36-10-01-00ABleed Air Shutoff ValveLeftB/1/0(M) May be inoperative provided:Affected valve is secured for no flow,Emergency pressurization system is considered inoperative (Refer to item 21-30-03),L ENG BLD AIR is selected OFF,Aircraft is operated at FL250 or below, andAircraft is not operated in known, forecast, or AFM-defined icing conditions.NOTE: Amber BLD SEL NOT NORM L message may appear.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 36, Pneumatics - Dispatch Deviation.36-10-01-00BBleed Air Shutoff ValveRightB/1/0(M) May be inoperative provided:Affected valve is secured for no flow,R ENG BLD AIR is selected OFF,BAG HEAT is selected OFF, andAircraft is not operated in known, forecast, or AFM-defined icing conditions.NOTE: Amber BLD SEL NOT NORM R message may appear.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 36, Pneumatics - Dispatch Deviation.36-10-01-01ABleed Air Shutoff ValveHigh-pressure (HP)C/2/1(M) One may be inoperative provided:Affected valve is secured for no flow,Associated ENG BLD AIR knob is selected to LP,Aircraft is not operated in known, forecast, or AFM-defined icing conditions, andAircraft is operated at FL410 or below).NOTE: Amber BLD SEL NOT NORM L-R message may appear.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 36, Pneumatics - Dispatch Deviation.36-10-01-01BBleed Air Shutoff ValveHigh-pressure (HP)C/2/0(M) May be inoperative provided:Both valves are secured for no flow,Both ENG BLD AIR knobs are selected to LP,Aircraft is not operated in known, forecast, or AFM-defined icing conditions, andAircraft is operated at FL410 or below.NOTE: Amber BLD SEL NOT NORM L-R message may appear.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 36, Pneumatics - Dispatch Deviation.36-10-02-00AEngine Bleed Air Precooler Temperature Control System(Dual bleed air source)B/2/1(M) One may be inoperative provided:Precooler temperature control system is deactivated,Precooler bypass air butterfly valve is secured open, andAircraft is not operated in known, forecast, or AFM-defined icing conditions.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 36, Pneumatics - Dispatch Deviation.38-10-01Potable Water SystemC/-/0(M) May be inoperative provided:System is drained, andProcedures are established and used to ensure system is not serviced.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 38, Water/Waste - Dispatch Deviation.38-10-01-01Potable Water SystemIndividual ComponentsC/-/0(M) Individual components may be inoperative provided:Associated components are deactivated or isolated, andAssociated system components are verified not to have leaks.NOTE: Any portion of system operating normally may be used.MAINTENANCE PROCEDUREDeactivate the associated components. Refer to the appropriate Interior Maintenance Manual. Verify no leaks are found. If leaks are found, system must be drained and all leaked fluid cleaned, system must not be re-serviced, and weight and Balance with missing fluid must be computed and provided to the flight crew for flight planning purposes.38-30-02Lavatory External Service SystemC/1/0(M) Individual components may be inoperative provided:Associated components are deactivated or isolated, andAssociated system components are verified not to have leaks.NOTE:Any portion of the system operating normally may be used.MAINTENANCE PROCEDUREDeactivate the associated components. Refer to the appropriate Interior or Airframe Maintenance Manual. Verify no leaks are found. If leaks are found, system must be drained and all leaked fluid cleaned, system must not be re-serviced, and weight and Balance with missing fluid must be computed and provided to the flight crew for flight planning purposes.38-30-02-01BLavatory External Service SystemDump CableC/1-/0(M) May be inoperative provided lavatory is serviced by alternate means.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 38, Water/Waste - Dispatch Deviation.38-30-02-08Lavatory External Service SystemHeater GasketC/1/0(M) May be inoperative provided:Waste line is drained of all fluids,Heater gasket is deactivated,Drain heaters are considered inoperative (Refer to item 30-70-01), andToilet is not serviced within four hours of landing or at surface temperatures below +10 C.MAINTENANCE PROCEDUREPull and secure the DRAIN HEATERS circuit breaker on the aft interior junction box.38-30-04-01Overboard Drain(Excluding drain heater)Aft Vanity BasinC/1/0(O) May be damaged or obstructed provided:All liquid is removed from basin, andBasin is placarded "DO NOT USE".OPERATIONAL PROCEDURERemove all liquid from the basin by allowing it to drain while on the ground or using other means such as towels or wet vac.38-30-04-03Overboard Drain(Excluding drain heater)Refreshment CenterC/1/0(O) May be damaged or obstructed provided:All liquid is removed from refreshment center hot liquid storage and drip pan,Refreshment center hot liquid storage and drip pan are placarded "DO NOT USE", andIce drawer drain valve remains closed.OPERATIONAL PROCEDURERemove all liquid from the drip pan by allowing it to drain while on the ground or using other means such as towels or wet vac.Empty the hot liquid storage tanks.46-00-01-00BElectronic Flight Bag (EFB) SystemClass 3 EFBC/-/0(O) May be inoperative provided alternate procedures are established and used.NOTE: Any function, program or document which operates normally may be used.OPERATIONAL PROCEDUREAppropriate and current navigational publications for route of flight and alternates must be carried onboard.46-00-01-01BElectronic Flight Bag (EFB) SystemData Connectivity(Class 2)C/-/0(O) May be inoperative provided alternate procedures are established and used.OPERATIONAL PROCEDUREAppropriate and current navigational publications for route of flight and alternates must be carried onboard.46-00-01-02BElectronic Flight Bag (EFB) SystemPower Connection(Class 1 & 2)C/-/0(O) May be inoperative provided alternate procedures are established and used.OPERATIONAL PROCEDUREAppropriate and current navigational publications for route of flight and alternates must be carried onboard.46-00-01-03AElectronic Flight Bag (EFB) SystemMounting Device(Class 2)D/-/0(M) May be inoperative provided:Associated EFB and hardware is secured by an alternate means or removed from the aircraft, andProcedures do not require its use.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 25, Equipment/Furnishings - Dispatch Deviation.46-00-01-03BElectronic Flight Bag (EFB) SystemMounting Device(Class 2)C/-/0(M) May be inoperative provided:Associated EFB and hardware is secured by an alternate means or removed from the aircraft, andProcedures do not require its use.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 25, Equipment/Furnishings - Dispatch Deviation.OPERATIONAL PROCEDUREThe affected flight crew member(s) will determine an adequate storage location for the EFB(s) prior to flight.The flight crew will brief on alternate EFB usage for the intended flight.49-20-01Auxiliary Power Unit (APU)C/1/0(M) May be inoperative provided:APU is deactivated, andProcedures do not require its use.MAINTENANCE PROCEDUREPull and secure the APU MASTER circuit breaker on the copilot’s circuit breaker panel.49-30-01APU Fuel Shutoff ValveC/1/0(M) May be inoperative provided:APU fuel shutoff valve is verified closed, andAPU is considered inoperative (Refer to item 49-20-01).MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 49, Auxiliary Power Unit - Dispatch Deviation.49-50-02APU Bleed Air SystemC/1/0(O) May be inoperative provided:APU BLEED AIR is selected OFF, andAPU bleed air valve is verified closed.OPERATIONAL PROCEDUREPrior to engine start, start the APU.Verify no air flow exists from the overhead air outlets. 52-10-01-07Main Cabin DoorHandrailC/1/0(O) May be inoperative or damaged provided:Door operates and latches normally, andAlternate procedures are established and used for assisting passengers during entry and exit.OPERATIONAL PROCEDUREPrior to entry and exit, occupants are briefed by a crew member not to utilize the handrail.Passengers may need assistance entering and exiting the aircraft.52-10-01-10Main Cabin DoorLift MotorC/1/0(O) May be inoperative provided:a)Lift motor clutch is disengaged, andb)Gas Strut is operable.OPERATIONAL PROCEDUREWARNING: Gas strut must be operable for safe door opening with the lift motor disengaged.Disengage the lift motor clutch.Remove access panel in the left fwd cabinet.Push handle located on motor aft, until latched.While standing on the ground outside the airplane, lift door to verify motor has disengaged. Door should lift easily.Persons on the ground can lift the door into the frame.If no ground assistance is available, crew can use the cabin door strap from the drawer beneath the fwd side facing seat to lift the door into the frame.Insert the ball catch pin on the strap into the receptacle located at the top of the view port (referenced with the door open) of the first step riser.Stand securely in the cabin and use the cabin door strap to lift the door into the frame. Two crew members may be required to successfully lift and close the door.While holding the door in frame, move the latching handle into the closed and latched position.Verify the cabin door amber DOOR OPEN light extinguishes.Verify all locking flags are visible in the 6 sight glass locations.WARNING: Door is not secure if latch lock flags are not fully visible.If cabin door strap was used, remove the ball catch pin from the cabin door receptacle and stow the strap in the drawer beneath the fwd side facing seat.52-30-01-02Aft Baggage DoorDoor SealC/1/0(O) May be damaged provided baggage compartment is verified empty prior to each flight.OPERATIONAL PROCEDUREPrior to each flight, a crew member must make sure the aft baggage compartment is empty.52-30-01-05Aft Baggage DoorDoor CableB/2/1(M) One may be inoperative or missing provided:Affected cable is removed, andDoor steps are not usedMAINTENANCE PROCEDURERefer to the 680A Maintainence manual section 52 for removal of the Baggage Door Cable.52-30-01-05Aft Baggage DoorGas SpringC/1/0(O) May be inoperative or missing provided precautions are taken when opening door.OPERATIONAL PROCEDUREThe flight crew should brief any occupants or crewmembers that would need to access the aft baggage that the spring is inoperative.When opened, the door shall be held open or supported by another means which is secure enough to prevent the door from swinging in the wind.52-50-01Cockpit Divider DoorC/2/0(M) May be inoperative provided door is secured open.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 25, Equipment/Furnishings - Dispatch Deviation.52-50-02Lavatory DoorC/2/0(M) May be inoperative provided door is secured open.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 25, Equipment/Furnishings - Dispatch Deviation.52-50-07Door Warning SystemMain Cabin DoorB/1/0(O) May be inoperative provided:Flight crew follows AFM CHECK DOORS procedures,Lock flags are fully engaged in all door site glass locations, andInternal door handle is verified in the fully latched position.OPERATIONAL PROCEDUREFollowing the completion of the AFM CHECK DOORS procedures, a crew member must verify that all door flags are engaged and fully visible in the site glasses. Also a visual check of the internal door handle to ensure it is in the fully latched position is required.78-30-01Thrust ReverserC/2/0(M) May be inoperative provided:Affected thrust reverser is deactivated and secured in forward thrust position, andTakeoffs on contaminated runways are prohibited.NOTE: Flight crew should review AFM Single-Engine Reversing procedure.MAINTENANCE PROCEDURERefer to 680A Maintenance Manual Chapter 78, Exhaust - Dispatch Deviation.APPENDIX ACABIN ALTITUDE vs. CABIN PRESSURE DIFFERENTIAL CONVERSION(Cabin Pressure Differential Display or Cabin Altimeter Inoperative)CABIN ALTAIRCRAFT PRESSURE ALTITUDE x 1000'CABIN ALTITUDE x 1000'x 1000'051015202528313335373941434547495111.01.43.04.34.95.65.96.36.66.97.17.47.67.88.08.110.51.63.24.55.15.86.16.46.87.17.37.57.88.08.18.310.00.01.83.44.75.36.06.36.67.07.37.57.78.08.28.38.59.50.22.03.64.95.56.26.56.87.27.57.77.98.28.48.58.79.00.42.23.85.15.76.46.77.07.47.77.98.18.48.68.78.98.50.62.44.05.35.96.66.97.27.67.98.18.38.68.88.99.18.00.82.64.25.56.16.87.17.57.88.18.38.68.89.09.29.37.51.02.84.45.76.47.17.37.78.08.38.58.89.09.29.49.57.01.23.04.65.96.67.37.57.98.28.58.79.09.29.49.69.76.51.53.34.86.16.87.57.88.18.48.79.09.29.49.69.810.06.01.73.55.06.37.07.78.08.38.68.99.29.49.69.810.05.51.93.75.26.57.27.98.28.58.99.19.49.69.910.15.02.13.95.56.87.58.28.48.89.19.49.69.910.14.52.44.25.77.07.78.48.79.09.39.69.910.14.02.64.45.97.27.98.68.99.29.59.810.13.52.84.66.27.58.28.99.19.59.810.13.03.14.96.47.78.49.19.49.710.02.53.35.16.78.08.69.39.610.02.03.65.46.98.28.99.69.910.21.53.85.67.28.59.19.810.11.04.15.97.48.79.410.10.50.04.36.17.79.09.70.00.00.34.66.47.99.29.9-0.50.30.64.96.78.29.510.2-1.00.50.85.16.98.59.810.5EXAMPLE:Aircraft is at FL 350 and Cabin Pressure Differential Gauge reads 8.8 psid, Cabin Altitude is 5,000'.EXAMPLE:Aircraft Is At FL 350 and Cabin Altimeter reads 5,000', Cabin Pressure Differential is 8.8 psid. ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download