Paper Title (use style: paper title)



Title of the Paper, capitalize each word, 24 pt size, Times New Roman with Bold, center alignment

Author-1, Author-2 and Author-3;` 11pt, Times New Roman

Affiliation, Dept. and College name. Address E-mail: 10`pt, Times New Roman

Abstract— The abstract should not be more than 300 words. The font should be in Times New Roman, 9 pt and bold. The alignment should be in justified. The line spacing of two lines should be single. The abstract needs to mentions clearly about the novelty of the research paper. The special characters should be mention clearly about the abbreviations. The paragraph spacing of the abstract should be 10pt (after).

Keywords— the authors can provide minimum 4 and maximum 8 keywords on their research paper. The keywords will helps to find the paper by searching in search engines and will also helps to us for finding suitable reviewers. The proper keywords will increase the quality of paper. The font and style should follow and same as Abstract which is mentioned above.

Introduction

The author should prepare the paper with page setup as A4, top 1 inch, bottom 0.75 inch, left and right as 0.55 inch and orientation of portrait. The page layout is double column and spacing between two columns is 0.25 inch. The length of the paper is restricted to maximum 10 pages, however, the author needs to take prior permission from publisher if page limit exceed 10 pages. The authors are advised to divide the research paper into few sections/parts with appropriate headings. The introduction section is the brief overviews of the research work how the authors are done it. These sections should follow the style as font should be Times New Roman with 10 pt. these sections should not be in bold. The line spacing will be single with every paragraph spacing after at 6 pt with before 0 pt. the section headings should be in small capital letters as shown in above Introduction section. The headings should be in roman numerical with paragraph spacing of before 8pt and after 4 pt. All the references should be cited properly like [1-4] [i.e. if references from 1 to 4.] or [1, 4] [i.e. if references 1 and 4].

For office use only: Please don’t edit this space. The IJNSE office will do necessary modifications/write-up once paper got accepted.

Article details:

Received date: , Revision date: , Accepted date: ,

Citation of paper: list of author(s), “Title of the paper”, International Journal of New Technologies in Science and Engineering (IJNTSE), Vol. No., Issue. No, pp. no, Month. Year.

*Corresponding author:

A copyright belongs to IJNTSE. The author(s) are only responsible for any allegations on the paper. For any further information, please contact to corresponding author.

Please make sure to avoid the plagiarism and wrong content while preparing the paper. The journal is strict at plagiarism and restricted to not more than 15%.

The organization of paper can include, it will helps to reader for better understand on paper. The review process may take several months, hence the authors are advised to wait till it comes out.

Literature Review

The literature review can provide the research till up to date. Hence, it is advisable to provide latest references in literature review and it will helps to reviewers and readers for better understand on your research. This section is an optional, it can be included in introduction section.

Description of the System or Research

The detailed description is required to analyze your research paper for validation.

Novelty or Proposed Work

This section is main part of the research article, hence, the authors should take care about the write-up and explanation on each and every point for better understand by reviewers and readers. The paper will be accepted if there will be a significance of novelty on the paper/article.

The figures, equations and tables should be placed at proper location on the paper. Every figure should be noted as Fig. with appropriate number. The figure numbers should be in order while writing about it. All figures should be cited in the article. The figure caption should be with same font of 10 pt and Times New Roman with alignment of center. The caption should be placed at below the figure. The table caption should be placed at above and same format like Fig. The equation numbers should be in order. The example of figure, table and equations are providing below. Citations of references should follow the format as: Name of author(s), “Title of the paper”, Name of Journal in italic, Vol. no, Issue no, pp., Month, Year. The font size of references is 9 pt and examples are given in reference section below.

Example of equation:

[pic] (1)

[pic] (2)

[pic] (3)

where, k (modulation index)=1;

Vo (Load voltage) =[pic] V;

Io (Nominal current) =10A;

fr (Fundamental frequency) = 50 Hz;

fs (Switching frequency) = 3 kHz;

Vo,av (Total harmonic load voltage) = 5% of Vo ;

Lf = Inductance of filter; Cf = Capacitance of filter.

Example of Figure:

[pic]Fig. 3: P-V characteristics of PV system under various irradiances

If figure is not fit in the column of double column format, then please make a single column only for figure and insert the figure then follow double column for remaining paper.

Example of table:

Table-I: Parameters of PV

|Open circuit voltage |36.90 V |

|Short circuit current |8.01 A |

|Voltage at maximum power |30.3 V |

|Current at maximum power |7.10 A |

|Number of modules connected in series |22 |

|Rated irradiance |1000 w/m2 |

|Rated power |4.73 kW |

Results and Discussions

The results or outcome of research work should be presented with valid analysis.

Conclusion

The abstract and conclusion parts are very important of paper. Many readers will download the paper by reading first abstract and conclusion. The paper doesn’t accept without conclusion part.

Acknowledgement: this is the option to author for providing necessary information if required.

Note*: references, figure numbers, numbering of equations and tables should follow the order in sequence. It should be cited in ascending order.

References

[1] Müller S., Deicke M., and De Doncker Rik W. “Doubly fed induction generator system for wind turbines”, IEEE Industry Applications Magazine, May/June, 2002, pp. 26-33.

[2] Bose B.K, Power Electronics and Motor Drives, Academic Press, Imprint of Elsevier, 2006.

[3] Dr. Siva Ganesh Malla, Priyanka Malla and Rajesh Koilada, “Solar Energy based Hybrid Electric Car: Part 1”, International Journal of New Technologies in Science and Engineering (IJNTSE), Vol. 6, Issue 6, pp. 11- 25, Dec. 2019.

Author biography:

Name of author: this will help to identity the authors and will help Google scholar and other similar pages to track your paper. Hence, all authors should provide their biography when submitting final paper after accepting. The biography should not more than 300 words. The font size should not be more than 9 pt with Times New Roman. This is your wish to provide details back ground of your research. Please don’t provide your personal mobile numbers anywhere.

Author’s website: if any,

Author’s Google scholar page: if have

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download