Automotive Mechnaical Assembly NC II
|COMPETENCY-BASED CURRICULUM |[pic] |
|[pic] |
|Sector: |
|AUTOMOTIVE MANUFACTURING |
|Qualification: |
|AUTOMOTIVE MECHANICAL ASSEMBLY NC II |
|[pic] |Technical Education and Skills Development Authority |
| |East Service Road, South Superhighway, Taguig City, Metro Manila |
TABLE OF CONTENTS
Page
A. COURSE DESIGN 1-6
B. MODULES OF INSTRUCTION 7-85
• Basic Competencies 7
o Participating in workplace communication 8-11
o Working in a team environment 12-14
o Practicing career professionalism 15-18
o Practicing occupational health and safety procedures 19-23
• Common Competencies 24
o Performing mensuration and calculation 25-26
o Reading, interpreting and applying engineering manuals/specification 29-33
o Moving and positioning vehicle 34-37
o Applying appropriate sealant/adhesive 38-42
o Performing shop maintenance 43-47
• CoRE Competencies 48
o Assembling mechanical assemblies using jigs/fixtures 49-55
o Mounting/installing brake and fuel systems 56-61
o Mounting/installing power drive system 62-66
o Mounting/installing suspension drive train 67-71
o Installing/fitting out trim parts/components 72-77
o Perform final engine run 78-82
o Performing wheel alignment operations 83-85
C. ACKNOWLEDGEMENT 86
COURSE DESIGN
COURSE TITLE : AUTOMOTIVE MECHANICAL ASSEMBLY NC II
NOMINAL DURATION : 143 Hours
COURSE DESCRIPTION :
This course is designed to equip individual the competencies that a person must achieve to be able to assemble mechanical assemblies using jigs/fixtures and to mount/install assemblies/parts/components into automotive vehicle body. It covers the area of power drive, suspension drive train, brake and fuel system and trim parts/components. It also includes non-assembly activities but are considered to be part of competencies to undertake like performing final engine run and performing wheel alignment operations.
This course is also designed to provide basic and common skills to equip individual with operational skills in automotive mechanical assembly.
To obtain this, all units prescribed for this qualification must be achieved.
ENTRY REQUIREMENTS:
Student/trainee should possess the following requirements:
• can communicate both orally and in written form;
• physically and mentally fit;
• with good moral character; and
• with experience in basic machining..
COURSE STRUCTURE:
BASIC COMPETENCIES
(18 hours)
|Units of Competency |Module Title |Learning Outcomes |Nominal Duration|
|Participate in workplace | Participating in |Obtain and convey workplace information |4 hours |
|communication |workplace |Complete relevant work-related document | |
| |communication |Participate in workplace meeting and discussions | |
|Work in a team environment |2.1 Working in a team environment |Describe and identify team role and responsibility |4 hours |
| | |Describe work as a team member | |
|3. Practice career professionalism |3.1 Practicing career |Integrate personal objectives with organizational |4 hours |
| |professionalism |goals. | |
| | |Set and meet work priorities. | |
| | |Maintain professional growth and development. | |
|4. Practice occupational health and|4.1 Practicing occupational health |Identify hazards and risks. |6 hours |
|safety procedures |and safety procedure |Evaluate hazards and risks. | |
| | |Control hazards and risks. | |
| | |Maintain occupational health and safety awareness. | |
COMMON COMPETENCIES
(20 hours)
|Units of Competency |Module Title |Learning Outcomes |Nominal Duration|
|Perform mensuration and calculation|Performing mensuration and |Select measuring instruments |5 hours |
| |calculation |Carry out measurements and calculation | |
| | |Maintain measuring instruments | |
|Read, interpret and apply |Reading, interpreting and applying |Identify and access engineering manuals/ |5 hours |
|engineering manuals/ specification|engineering manuals/ specification|specifications | |
| | |Interpret manuals | |
| | |Apply information in the manual | |
| | |Store manuals | |
|Move and position vehicle |Moving and positioning vehicle |Prepare vehicle for driving |2 hours |
| | |Move and position vehicle | |
| | |Check vehicle | |
|Apply appropriate sealant/adhesive |Applying appropriate sealant/ |Identify appropriate sealant/adhesive |3 hours |
| |adhesive |Prepare surface for application of sealant/ adhesive | |
| | |Apply sealant/adhesive evenly | |
| | |Store/dispose-of sealant/ adhesive | |
|5. Perform shop maintenance |5.1 Performing shop maintenance |5.1.1 Inspect/clean tools and work area |5 hours |
| | |Store/arrange tools and shop equipment | |
| | |Dispose wastes/used lubricants | |
| | |5.1.4 Report damaged tools/equipment | |
CORE COMPETENCIES
(105 hours)
|Units of Competency |Module Title |Learning Outcomes |Nominal Duration|
|Assemble mechanical assemblies |1.1 Assembling mechanical |Obtain materials/parts |15 hours |
|using jigs/fixtures |assemblies using jigs/fixtures |Select and use tools and equipment | |
| | |Load/unload parts to jig | |
| | |Select and use adhesives, sealants and solvents | |
| | |Select and use hardware parts | |
| | |Assemble mechanical assemblies | |
|2. Mount/install brake and fuel |2.1 Mounting / installing brake |Select and use tools and equipment |15 hours |
|systems |and fuel systems |Select and use hardware parts | |
| | |Mount/install assemblies and parts | |
| | |Route service lines | |
|Mount/install power drive system |3.1 Mounting/ installing power |Select and use tools and equipment |15 hours |
| |drive system |Select and use hardware parts | |
| | |Mount/install assemblies and parts | |
| | |Route service lines | |
|4. Mount/install suspension drive |4.1 Mounting/ installing suspension|4.1.1 Select and use tools and equipment |15 hours |
|train |drive train |4.1.2 Select and use hardware parts | |
| | |4.1.3 Mount/install assemblies and parts | |
|5. Install/fit out trim parts/ |5.1 Installing/fitting out trim |Select and use tools and equipment |15 hours |
|components |parts / components |Select and use hardware parts | |
| | |Install/fit out assemblies and parts | |
| | |Select and use adhesives, sealants and solvents | |
|6. Perform final engine run |6.1 Performing final engine run |6.1.1 Select and use tools and equipment |15 hours |
| | |6.1.2 Select and use lubricants and fluids | |
| | |6.1.3 Bleed air and hydraulic system | |
| | |6.1.4 Record and report faults | |
|7. Perform wheel alignment |7.1 Performing wheel alignment |Prepare for the job |15 hours |
|operations |operations |Perform wheel alignment | |
ASSESSMENT METHODS
• Written examination
• Demonstration of practical skills
• Direct observation
• Interview
COURSE DELIVERY:
• Self-paced instruction
• Demonstration
• Lecture
• Discussion
• Dual training
• Distance learning
RESOURCES:
|Equipment |Evaporator assembly |
|Lifting equipment |Evaporator housing |
|Hoist |Front and rear bumpers assembly |
|Hangers and gears |Bumper fascia |
|Material handling |Insulation |
|forklift |Wheel assembly |
|hand pallet truck |Tires |
|Mechanized or manual conveyors |Steel or aluminum alloy rim |
|Tow motor |Tire valve |
|Robotic windshield sealer application |Windshield and door glasses assembly |
|Manual air and hydraulic pressurized lubrication |Dam rubber kit |
|Laser wheel alignment equipment |Door glass holders |
| | |
|Parts and Materials |Parts for power drive system |
|Parts for mechanical assemblies |Engine sub-assembly with transmission |
|Suspension assembly |Mechanical parts include but not limited to: |
|Coil spring |Engine support |
|Shock absorber |Transmission support |
|Suspension bushing |Propeller shaft and differential |
|Metal parts/components |Trim parts and components |
|Power drive assembly |Trim assemblies may include but not limited to: |
|Bare Engine assembly |Door and windshield glasses |
|Transmission assembly |Bumpers |
|Pressure plate | |
|Clutch disc |Trim parts may include but not limited to: |
|Intake and exhaust manifold |Floor carpet |
|Primary muffler |Seats |
|Catalytic converter |Door mechanism and components |
|Air conditioning compressor |Finishers for ceiling roof, doors and package tray, center and rear pillars|
|Belt drive |Moldings |
|Fuel tank assembly |Garnishes for front, center and rear pillars |
|Fuel tank |Inner view and side view mirrors |
|Floater | |
|Pump |Parts for brake and fuel systems |
|Brake, clutch and accelerator pedals assembly |Mechanical assemblies include but not limited to: |
|Bracket |Fuel tank assembly |
|Pedal and bushing |Brake pedal assembly |
|Radiator cooling system assembly |Clutch pedal assembly |
|Radiator |Accelerator pedal assembly |
|Metal brackets | |
|Inlet, outlet and return water hoses | |
|Air conditioning system | |
|Condenser assembly | |
|Expansion valve | |
|Mechanical parts include but not limited to: |Ear plug |
|Fuel filter | |
|Brake booster |Tools |
|Brake master cylinder |Impact gun |
|Brake and fuel pipes |Torque wrench |
|Brake and fuel valves |Hand tools |
|Brake disc |Special tools |
|Anti brake system kit |Rubber mallet |
|Brake drum | |
| |Training materials |
|Lubricants and fluids |Reference books |
|Sealants, adhesives and tapes |Manuals |
|Company standard forms |Catalogs |
| |Brochures |
|Personal safety devices or PPE |Modules |
|Safety goggles |CDs/Video tapes |
|Apron | |
|Gloves |6. Automotive vehicle body |
|Safety shoes | |
|Hard hat |7. Actual workplace or simulated workplace |
TRAINER’S QUALIFICATIONS:
• Must be a holder of Automotive mechanical assembly NC II
• Must have undergone training on Training Methodology II (TM II)
• Must be computer literate
• Must be physically and mentally fit
• *Must have at least 2 years job/industry experience
* Optional. Only when required by the hiring institution.
MODULES OF INSTRUCTION
BASIC COMPETENCIES
AUTOMOTIVE MECHANICAL ASSEMBLY NC II
BASIC COMPETENCY : COMMUNICATIONS
UNIT OF COMPETENCY : PARTICIPATE IN WORKPLACE COMMUNICATION
MODULE TITLE : PARTICIPATING IN WORKPLACE COMMUNICATION
MODULE DESCRIPTOR : This module covers the knowledge, skills and attitudes required to obtain, interpret and convey information in response to workplace requirements.
NOMINAL DURATION : 4 hours
PREREQUISITE : Receive and Respond to workplace Communication.
(NC I)
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module the students/ trainees will be able to:
LO1. Obtain and convey workplace information
LO2. Complete relevant work related documents.
LO3. Participate in workplace meeting and discussions.
LO1. OBTAIN AND CONVEY WORKPLACE INFORMATION.
ASSESSMENT CRITERIA:
1. Specific relevant information is accessed from appropriate sources.
2. Effective questioning, active listening and speaking skills are used to gather and convey information.
3. Appropriate medium is used to transfer information and ideas.
4. Appropriate non-verbal communication is used.
5. Appropriate lines of communication with superiors and colleagues are identified and followed.
6. Defined workplace procedures for the location and storage of information are used.
7. Personal interaction is carried out clearly and concisely.
CONTENTS:
• Parts of speech
• Sentence construction
• Effective communication
CONDITIONS:
The students/ trainees must be provided with the following:
• Writing materials (pen and paper)
• References (books)
• Manuals
METHODOLOGIES:
• Group discussion
• Interaction
• Lecture
• Reportorial
ASSESSMENT METHODS:
• Written test
• Practical/performance test
• Interview
L02. COMPLETE RELEVANT WORK RELATED DOCUMENTS.
ASSESSMENT CRTERIA:
1. Ranges of forms relating to conditions of employment are completed accurately and legibly.
2. Workplace data is recorded on standard workplace forms and documents.
3. Basic mathematical processes are used for routine calculations.
4. Errors in recording information on forms/ documents are identified and rectified.
5. Reporting requirements to superior are completed according to enterprise guidelines.
CONTENTS:
• Basic mathematics
• Technical writing
• Types of forms
CONDITIONS:
The students/trainees must be provided with the following:
• Paper
• Pencils/ball pen
• Reference books
• Manuals
METHODOLOGIES:
• Group discussion
• Interaction
• Lecture
ASSESSMENT METHODS:
• Written test
• Practical/performance test
• Interview
LO3. PARTICIPATE IN WORKPLACE MEETINGS AND DISCUSSIONS
ASSESSMENT CRITERIA:
1. Team meetings are attended on time.
2. Own opinions are clearly expressed and those of others are listened to without interruption.
3. Meeting inputs are consistent with the meeting purpose and established protocols.
4. Workplace interactions are conducted in a courteous manner appropriate to cultural background and authority in the enterprise procedures.
5. Questions about simple routine workplace procedures and matters concerning conditions of employment are asked and responded.
6. Meeting outcomes are interpreted and implemented.
CONTENTS:
• Sentence construction
• Technical writing
• Recording information
CONDITIONS:
The students/trainees must be provided with the following:
• Paper
• Pencils/ball pen
• References (books)
• Manuals
METHODOLOGIES:
• Group discussions
• Interaction
• Lecture
ASSESSMENT METHODS:
• Written test
• Practical/performance test
• Interview
BASIC COMPETENCY : TEAM WORK
UNIT OF COMPETENCY : WORK IN A TEAM ENVIRONMENT
MODULE TITLE : WORKING IN A TEAM ENVIRONMENT
MODULE DESCRIPTOR : This module covers the knowledge, skills, and attitudes required to relate in a work based environment.
NOMINAL DURATION : 4 hours
PREREQUISITE : TEAMWORK (NC I)
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the students/ trainees will be able to:
LO1. Describe and identify team role and responsibility in a team.
LO2. Describe work as a team.
LO1. DESCRIBE AND IDENTIFY TEAM ROLE AND RESPONSIBILITY IN A TEAM
ASSESSMENT CRITERIA:
1. Role and objective of the team is identified.
2. Team parameters, relationships and responsibilities are identified.
3. Individual role and responsibilities within team environment are identified.
4. Roles and responsibilities of other team members are identified and recognized.
5. Reporting relationships within team and external to team are identified.
CONTENTS:
• Team role.
• Relationship and responsibilities
• Role and responsibilities with team environment.
• Relationship within a team.
CONDITIONS:
The students/trainees must be provided with the following:
• Standard operating procedure (SOP) of workplace
• Job procedures
• Client/supplier instructions
• Quality standards
• Organizational or external personnel
METHODOLOGIES:
• Group discussion/interaction
• Case studies
• Simulation
ASSESSMENT METHODS:
• Written test
• Observation
• Simulation
• Role playing
LO2. DESCRIBE WORK AS A TEAM MEMBER
ASSESSMENT CRITERIA:
1. Appropriate forms of communication and interactions are undertaken.
2. Appropriate contributions to complement team activities and objectives were made.
3. Reporting using standard operating procedures followed.
4. Development of team work plans based from team’s role is contributed.
CONTENTS:
• Communication process
• Team structure/team roles
• Group planning and decision making
CONDITIONS:
The students/trainees must be provided with the following:
• SOP of workplace
• Job procedures
• Organization or external personnel
METHODOLOGIES:
• Group discussion/interaction
• Case studies
• Simulation
ASSESSMENT METHODS:
• Observation of work activities
• Observation through simulation or role play
• Case studies and scenarios.
UNIT OF COMPETENCY : PRACTICE CAREER PROFESSIONALISM
MODULE TITLE : PRACTICING CAREER PROFESSIONALISM
MODULE DESCRIPTOR : This module covers the knowledge, skills and attitudes in promoting career growth and advancement, specifically to integrate personal objectives with organizational goals set and meet work priorities and maintain professional growth and development.
NOMINAL DURATION : 4 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Integrate personal objectives with organizational goals
LO2. Set and meet work priorities
LO3. Maintain professional growth and development
LO1. INTEGRATE PERSONAL OBJECTIVES WITH ORGANIZATIONAL GOALS
ASSESSMENT CRITERIA:
1. Personal growth and work plans towards improving the qualifications set for professionalism are evident.
2. Intra and interpersonal relationship in the course of managing oneself based on performance evaluation is maintained.
3. Commitment to the organization and its goal is demonstrated in the performance of duties.
4. Practice of appropriate personal hygiene is observed.
5. Job targets within key result areas are attained.
CONTENTS:
• Personal development-social aspects: intra and interpersonal development
• Organizational goals
• Personal hygiene and practices
• Code of ethics
CONDITIONS:
The students/ trainees must be provided with the following:
• Workplace
• Code of ethics
• Organizational goals
• Hand outs and Personal development-social aspects
• CD’s, VHS tapes, transparencies
METHODOLOGIES:
• Interactive-lecture
• Simulation
• Demonstration
• Self paced instruction
ASSESSMENT METHODS:
• Role play
• Interview
• Written examination
LO2. SET AND MEET WORK PRIORITIES
ASSESSMENT CRITERIA:
1. Competing demands to achieve personal, team and organizational goals and objectives are prioritized.
2. Resources are utilized efficiently and effectively to manage work priorities and commitments.
3. Practices and economic use and maintenance of equipment and facilities are followed as per established procedures.
4. Job targets within key result areas are attained.
CONTENTS:
• Organizational key result areas (KRA)
• Work values and ethical standards
• Company policies on the use and maintenance of equipment
CONDITIONS:
The students/ trainees must be provided with the following
• Hand outs on
- Organizational KRA
- Work values and ethics
- Company policies and standards
- Sample job targets
• Learning guides
• CD’s, VHS tapes, transparencies
METHODOLOGIES:
• Interactive lecture
• Group discussion
• Structured activity
• Demonstration
ASSESSMENT METHODS:
• Role play
• Interview
• Written examination
LO3. MAINTAIN PROFESSIONAL GROWTH AND DEVELOPMENT
ASSESSMENT CRITERIA:
1. Training and career opportunities relevant to the job requirements are identified and availed.
2. Licenses and/or certifications according to the requirements of the qualifications are acquired and maintained
3. Fundamental rights at work including gender sensitivity are manifested/ observed
4. Training and career opportunities based on the requirements of industry are completed and updated.
CONTENTS:
• Qualification standards
• Gender and development (GAD) sensitivity
• Professionalism in the workplace
• List of professional licenses
CONDITIONS:
The students/trainees must be provided with the following
• Quality standards
• GAD handouts
• CD’s, VHS tapes on professionalism in the workplace
• Professional licenses samples
METHODOLOGIES:
• Interactive lecture
• Film viewing
• Role play/simulation
• Group discussion
ASSESSMENT METHODS:
• Demonstration
• Interview
• Written examination
• Portfolio assessment
UNIT OF COMPETENCY : PRACTICE OCCUPATIONAL HEALTH AND SAFETY PROCEDURES
MODULE TITLE : PRACTICING OCCUPATIONAL HEALTH AND SAFETY PROCEDURES
MODULE DESCRIPTOR : This module covers the knowledge, skills and attitudes required to comply with the regulatory and organizational requirements for occupational health and safety such as identifying, evaluating and maintaining occupational health and safety (OHS) awareness.
NOMINAL DURATION : 6 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Identity hazards and risks
LO2. Evaluate hazards and risks
LO3. Control hazards and risks
LO4. Maintain occupational health and safety awareness
LO1. IDENTIFY HAZARDS AND RISKS
ASSESSMENT CRITERIA:
1. Workplace hazards and risks are identified and clearly explained.
2. Hazards/risks and its corresponding indicators are identified in with the company procedures.
3. Contingency measures are recognized and established in accordance with organizational procedures.
CONTENTS:
1. Hazards and risks identification and control
2. Organizational safety and health protocol
3. Threshold limit value (TLV)
4. OHS indicators
CONDITIONS:
The students/ trainees must be provided with the following:
• Workplace
• Personal protective equipment (PPE)
• Learning guides
• Hand-outs
- Organizational safety and health protocol
- OHS indicators
- Threshold limit value
- Hazards/risk identification and control
• CD’s, VHS tapes, transparencies
METHODOLOGIES:
• Interactive -lecture
• Simulation
• Symposium
• Group dynamics
ASSESSMENT METHODS:
• Situation analysis
• Interview
• Practical examination
• Written examination
LO2. EVALUATE HAZARDS AND RISKS
ASSESSMENT CRITERIA:
1. Terms of maximum tolerable limits are identified based on threshold limit values (TLV)
2. Effects of hazards are determined.
3. OHS issues and concerns are identified in accordance with workplace requirements and relevant workplace OHS legislation.
CONTENTS:
• TLV table
• Philippine OHS standards
• Effects of hazards in the workplace
• Ergonomics
• ECC regulations
CONDITIONS:
The students/trainees must be provided with the following
• Hand outs on
- Philippine OHS standards
- Effects of hazards in the workplace
- Ergonomics
- ECC regulations
• TLV table
• CD’s, VHS tapes, transparencies
METHODOLOGIES:
• Interactive lecture
• Situation analysis
• Symposium
• Film viewing
• Group dynamics
ASSESSMENT METHODS:
• Interview
• Written examination
• Simulation
LO3. CONTROL HAZARDS AND RISKS
ASSESSMENT CRITERIA:
1. OHS procedures for controlling hazards and risk are strictly followed.
2. Procedures in dealing with workplace accidents, fire and emergencies are followed in accordance with the organization’s OHS policies.
3. Personal protective equipment (PPE) is correctly used in accordance with organization’s OHS procedures and practices.
4. Procedures in providing appropriate assistance in the event of workplace emergencies are identified in line with the established organizational protocol.
CONTENTS:
• Safety regulations
- Clean air act
- Electrical and fire safety code
- Waste management
- Disaster preparedness and management
• Contingency measures and procedures
CONDITIONS:
The students/trainees must be provided with the following:
• Hand outs on
- Safety regulations
- Clean air act
- Electrical and fire safety code
- Waste management
- Disaster preparedness and management
- Contingency measures and procedures
• OHS personal records
• PPE
• CD’s, VHS tapes, transparencies
METHODOLOGIES:
• Interactive lecture
• Symposium
• Film viewing
• Group dynamics
• Self-paced instruction
ASSESSMENT METHODS:
• Written examination
• Interview
• Case/situation analysis
• Simulation
LO4. MAINTAIN OCCUPATIONAL HEALTH AND SAFETY AWARENESS
ASSESSMENT CRITERIA:
1. Procedures in emergency related drill are strictly followed in line with the established organization guidelines and procedures.
2. OHS personal records are filled up in accordance with workplace requirements.
3. PPE are maintained in line with organization guidelines and procedures.
CONTENTS:
• Operational health and safety procedure, practices and regulations
• Emergency-related drills and training
CONDITIONS:
The students/trainees must be provided with the following
• Workplace
• PPE
• OHS personal records
• CD’s, VHS tapes, transparencies
• Health record
METHODOLOGIES:
• Interactive lecture
• Simulation
• Symposium
• Film viewing
• Group dynamics
ASSESSMENT METHODS:
• Demonstration
• Interview
• Written examination
• Portfolio assessment
MODULES OF INSTRUCTION
COMMON COMPETENCIES
AUTOMOTIVE MECHANICAL ASSEMBLY NC II
UNIT OF COMPETENCY : Perform Mensuration and Calculation
MODULE TITLE : Performing mensuration and calculation
MODULE DESCRIPTOR : This module covers calculating and solving mathematical problems related to automotive works including tolerances and measurement, including conversion of two systems of measurements.
NOMINAL DURATION : 5 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of the module, the trainees/students should be able to:
LO1. Select measuring instrument.
LO2. Carry out measurement and calculation
LO3. Maintain measuring instruments.
LO1. SELECT MEASURING INSTRUMENT
ASSESSMENT CRITERIA:
1. Objects or components to be measured are identified.
2. Correct specifications are obtained from relevant source.
3. Appropriate measuring instrument is selected as per job requirement.
CONTENTS:
• Types of measuring instruments and applications.
• Techniques in measuring parts/components.
• Methods of calculating/solving mathematical problems.
CONDITIONS:
• Equipment/tools/instrument
- Precise measuring instruments
- Calculator
- Calipers-vernier, micrometer, feeler gauge
- Steel rule, push rule
• Supplies/materials
- Pencil
- Paper
- Models of engine parts/components
• Instructional materials
- Reference books
- Learning guides
- Modules
METHODOLOGIES:
• Lecture
• Demonstration
• Practical exercises
ASSESSMENT METHODS:
• Written and oral examination
• Direct observation
LO2. CARRY OUT MEASUREMENT AND CALCULATION
ASSESSMENT CRITERIA:
1. Measuring tools are selected in line with job requirements.
2. Accurate measurements are obtained.
3. Calculations needed to complete work/task are performed using the four fundamental operation of mathematics.
4. Numerical computation checked is correct and accurate.
CONTENTS:
• Conversion of units of measurement from English-metric and vise versa.
• Techniques in determining tolerance/allowance of parts/components
• Calibrating and using testing instruments.
• Solving problems using formulas.
• Finding areas of different geometrical figures.
CONDITIONS:
The students/trainees must be provided with the following:
• Equipment/tools/instrument
- Calculator
- Steel rule, push rule
- Precise measuring instrument - vernier caliper, micrometer, feeler gauge
• Supplies/materials
- Paper
- Pencil
- Vehicle parts
• Instructional materials
- Reference books
- Learning guides
- Modules
METHODOLOGIES:
• Demonstration
• Practical exercises
ASSESSMENT METHODS:
• Written and oral examination
• Direct observation
LO3. MAINTAIN MEASURING INSTRUMENT
ASSESSMENT CRITERIA:
1. Measuring instruments are cleaned before and after using.
2. Measuring instruments are kept in safe dry place.
3. Proper techniques in using precise instrument according to manufacturers standards.
4. Proper handlings of measuring instruments are observed in accordance with industry standards.
CONTENTS:
• Handling and caring of measuring instruments.
• Calibrating measuring instrument.
• Safe handling and procedures in using measuring instruments.
• Storing of measuring instruments.
CONDITIONS:
Students/trainees must be provided with the following:
• Equipment/tools/instrument
- Computer
- VHS player
- OHP
- Vernier calipers, micrometer, feeler gauge
- Steel rule, push rule
• Supplies/materials
- Paper
- Pencil
- Vehicle parts
• Instructional materials
- Reference books
- Learning guides
- Modules
- CD’s VHS tapes, transparencies
METHODOLOGIES:
• Lecture
• Demonstration
• Simulation
ASSESSMENT METHODS:
• Written examination
• Direct observation
• Oral examination
UNIT OF COMPETENCY : READ, INTERPRET AND APPLY ENGINEERING MANUALS / SPECIFICATIONS
MODULE TITLE : READING, INTERPRETING AND APPLYING ENGINEERING MANUALS / SPECIFICATIONS
MODULE DESCRIPTOR : This module deals with identifying, interpreting and applying automotive mechanical assembly manuals/specifications in accordance with requirements of the job.
NOMINAL DURATION : 5 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Identify and access engineering manuals/specifications
LO2. Interpret manuals
LO3. Apply information in manual
LO4. Store manuals
LO1. Identify and access engineering MANUALS / specifications
ASSESSMENT CRITERIA:
1. Appropriate engineering manuals/specifications are identified and accessed as per job requirements.
2. Version and date of drawing is checked to ensure correct specification and procedure are identified.
CONTENTS:
• Types of drawings used in automotive manufacturing industry
• Identification of symbols used in the drawings
• Identification of units of measurements
• Unit conversion
CONDITION:
Students/trainees must be provided with the following:
• Vehicle assembly manuals
• Vehicle quality standard manuals
• Vehicle specification manuals
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Interview
LO2. INTERPRET MANUALS
ASSESSMENT CRITERIA:
1. Relevant sections, chapters of manuals/specifications are located in relation to the work to be conducted.
2. Information in the manual are interpreted in accordance to industry practices.
CONTENTS:
• Locating relevant dimensions and drawing sections
• Ways of accessing information and data
• Interpreting information in the manual based on industry practices
CONDITION:
Students/trainees must be provided with the following:
• Vehicle assembly manuals
• Vehicle quality standard manuals
• Vehicle specification manuals
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Interview
LO3. APPLY INFORMATION IN MANUAL
ASSESSMENT CRITERIA:
1. Engineering manual is interpreted according to job requirements.
2. Work steps are correctly identified in accordance with manufacturer’s specification.
3. Manual data is applied according to the given task.
CONTENTS:
• Reading and interpreting engineering manuals
• Identifying work steps to be undertaken based on manual
• Applying work data based on given task
CONDITION:
Students/trainees must be provided with the following:
• Vehicle assembly manuals
• Vehicle quality standard manuals
• Vehicle specification manuals
• Work data
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Interview
LO4. STORE MANUALS
ASSESSMENT CRITERION:
1. The manuals and specification are stored properly to ensure prevention of damage, ready access and updating of information when required in accordance with company requirements.
CONTENTS:
• Proper storage of engineering manuals/specifications
• Updating of information
CONDITION:
Students/trainees must be provided with the following:
• Engineering manuals
• Storage container or cabinet
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Interview
UNIT OF COMPETENCY : MOVE AND POSITION VEHICLE
MODULE TITLE : MOVING AND POSITIONING VEHICLE
MODULE DESCRIPTOR : This module covers moving and positioning vehicle in a workshop with the right knowledge, skills and attitude that a person needed.
NOMINAL DURATION : 2 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of the module, the trainees/students should be able to:
LO1. Prepare vehicle for driving.
LO2. Move and position vehicle
LO3. Check vehicle
LO1. PREPARE VEHICLE FOR DRIVING
ASSESSMENT CRITERIA:
1. Correct check-up procedures of engine system is performed.
2. Tire inflation pressures checked according to manufacturer’s specification.
3. Braking system and fluid level are properly checked.
4. Engine belt tension and other necessary units are checked in accordance with manual.
5. Lighting system is checked according to established procedures.
CONTENT:
• Safety in driving
• Engine system check up procedures
• Tire inflation pressure specification
• Belt tension checking procedures
• Driver’s code and conduct
CONDITIONS:
The students/trainees must be provided with the following:
• Equipment/tools/instrument
- Good running condition vehicle
- Car lift/bay
- Belt tension gauge
• Supplies/materials
- Paper
- Pencil
- Brake fluid/engine oil/coolant
• Instructional materials
- Reference books
- Learning guides
- Modules
METHODOLOGIES:
• Lecture
• Demonstration
• Practical exercises
ASSESSMENT METHODS:
• Written and oral examination
• Direct observation
LO2. MOVE AND POSITION VEHICLE
ASSESSMENT CRITERIA:
1. Vehicle to be moved or repositioned is identified or selected as per job requirements.
2. Vehicle is driven safely to the designated location according to job specification.
3. Vehicle is parked properly following safety procedures and techniques.
CONTENT:
• Starting an engine
• Shifting gears.
• Steering vehicle
• Brake application
• Driving skills
CONDITIONS:
The students/trainees must be provided with the following:
• Equipment/tools/instrument
- Functional, good running condition light vehicle
- Car lift/bay
- Belt tension gauge
• Supplies/materials
- Paper
- Pencil
• Instructional materials
- Reference books
- Learning guides
- Modules
METHODOLOGIES:
• Demonstration
• Practical exercises
ASSESSMENT METHODS:
• Written and oral examination
• Direct observation
LO3. CHECK VEHICLE
ASSESSMENT CRITERIA:
1. Vehicle position is checked as per requirement.
2. Check up procedures is performed upon parking.
3. Vehicle is checked for external damage.
CONTENTS:
• Parking safety techniques
• Vehicle inspection
CONDITIONS:
Students/trainees must be provided with the following:
• Vehicle unit
• Workplace with proper illumination
• Wiping cloth
METHODOLOGIES:
• Lecture
• Demonstration
• Simulation
ASSESSMENT METHODS:
• Written examination
• Direct observation
• Oral examination
UNIT OF COMPETENCY : APPLY APPROPRIATE SEALANT/ADHESIVE
MODULE DESCRIPTOR : APPLYING APPROPRIATE SEALANT/ADHESIVE
MODULE DESCRIPTOR : This module deals with identifying and applying sealant/adhesive to automotive vehicle unit in accordance with requirements of the job.
NOMINAL DURATION : 3 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of the module, the trainees/students should be able to:
LO1. Identify appropriate sealant/adhesive
LO2. Prepare surface for sealant/adhesive application
LO3. Apply sealant/adhesive evenly
LO4. Store unused and dispose used sealant/adhesive
LO1. IDENTIFY APPROPRIATE SEALANT/AHESIVE
ASSESSMENT CRITERIA:
1. Sealant/adhesive is selected in line with job requirements and manufacturer’s specification.
2. Sealant/adhesive checking is performed to ensure that product is appropriate for use.
CONTENTS:
• Use of sealant and adhesive
• Types and classification of sealant and adhesives
CONDITIONS:
Students/trainees must be provided with the following:
• Materials list
• Sealant/adhesive specification manual
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
• Distance learning
ASSESSMENT METHODS:
• Written/oral examinations
• Direct observation
• Interview
LO2. PREPARE SURFACE FOR SEALANT/ADHESIVE APPLICATION
ASSESSMENT CRITERIA:
1. Surface materials are identified as per construction.
2. Surface is cleaned and free of moisture, dust and other foreign matters to ensure maximum adhesion or seal.
CONTENT:
• Surface preparation condition
CONDITIONS:
The students/trainees must be provided with the following:
Tools and equipment include:
• Putty knife
• Scraper
• Compressor
• Steel brush
• Paint brush
• Rubber hammer
• Hand tools
Personal protective equipment include:
• Gloves
• Apron
• Safety shoes
• Goggles
• Gas mask
• Supplies and materials
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
• Distance learning
ASSESSMENT METHODS:
• Written/oral examinations
• Direct observation
• Project method
• Interview
LO3. APPLY SEALANT/ADHESIVE EVENLY
ASSESSMENT CRITERIA:
1. Sealant/adhesive is applied evenly on the surface in line with manufacturer’s specification.
2. Excess sealant/adhesive is removed by sanding or scrapping.
3. Tools and equipment used to apply sealant/adhesive are appropriate to job requirements.
4. Safety are observed and PPE are worn in accordance with industry SOP.
5. Hazards associated with the use of sealant and adhesives are identified.
CONTENTS:
• Techniques in storing manuals.
• Procedures in maintaining manuals.
CONDITIONS:
Students/trainees must be provided with the following:
• Sealer gun
• Sealer nozzle/tip
• Consumable materials
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
• Distance learning
ASSESSMENT METHODS:
• Written/oral examinations
• Direct observation
• Project method
• Interview
LO4. STORE UNUSED AND DISPOSE USED SEALANT/ADHESIVE
ASSESSMENT CRITERIA:
1. Sealant/adhesive is stored as per prescribed procedure.
2. Wastes are disposed as per workshop SOP.
CONTENT:
• Criteria for checking sealant/adhesive.
CONDITIONS:
Students/trainees must be provided with the following:
• Supplies/materials
• Manufacturer’s manual
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
• Distance learning
ASSESSMENT METHODS:
• Written/oral examinations
• Direct observation
• Project method
• Interview
UNIT OF COMPETENCY : Perform Shop Maintenance
MODULE TITLE : PERFORMING SHOP MAINTENANCE
MODULE DESCRIPTOR : This module covers inspecting, cleaning, arranging and storing tools and shop equipment, including disposal of waste and used lubricant and reporting of damaged tools and equipment in the shop.
NOMINAL DURATION : 5 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Inspect and clean tools, equipment and the work area.
LO2. Store/arrange tools and shop equipment.
LO3. Dispose waste and used lubricants.
LO4. Report damaged tools and equipment.
LO1. INSPECT AND CLEAN TOOLS, EQUIPMENT AND WORK AREA
ASSESSMENT CRITERIA:
1. Tools, equipment and the work area is inspected and cleaned, free from dust, grease and other substances.
2. Cleaning solvent used as per workshop cleaning requirements is observed.
3. Work area is checked and cleaned.
4. Wet surface or spot in the work area is kept dry.
CONTENTS:
• Workshop policies.
• Types and usage of cleaning chemicals.
• Safe handling of equipment and tools.
• Service procedures.
• Equipment maintenance standards.
CONDITIONS:
Students/trainees must be provided with the following:
• Open workshop/garage
• Well ventilated enclosed work and office area
• Wash area and mess hall
• Cleaning chemicals
• Inventory of equipment and tools
• Rugs
• Containers for used oils
• Vehicle
• Oiler
METHODOLOGIES:
• Lecture
• Demonstration
• Self-paced instruction
• Dual Training
ASSESSMENT METHODS:
• Direct observation
• Practical
• Interview
• Written examination
LO2. STORE/ARRANGE TOOLS AND SHOP EQUIPMENT
ASSESSMENT CRITERIA:
1. Tools and equipment are arranged and stored in their respective shelves/ location.
2. Corresponding labels are posted and visible.
3. Tools are secured and logged in the record book.
CONTENTS:
• Storage and disposal of hazardous/flammable tools/materials.
• Personal safety procedures.
• Relevant technical information
• Labeling procedures
• Principles of total quality management (TQM) and 5S
CONDITIONS:
Students/trainees must be provided with the following:
• Tool cabinet
• Appropriate tools and equipment
• Tool room
• Fire extinguishers
• Tool kit
• Log/record book
• Labeling materials
METHODOLOGIES:
• Interactive lecture
• Dual Training
• Self-paced instruction
• Simulation
ASSESSMENT METHODS:
• Practical
• Direct observation
• Interview
• Written examination
LO3. DISPOSE WASTE AND USED LUBRICANTS
ASSESSMENT CRITERIA:
1. Waste and used lubricants are disposed in accordance with the standard operational procedures and environmental regulations.
2. Containers for waste and used lubricants are properly labeled.
3. Personal safety in disposing waste and used lubricants is evident.
CONTENTS:
• Effects of automotive wastes to men and its environment.
• Waste management and disposal
• Cleaning chemicals for grease and lubricants
• Labeling procedures and technique
CONDITIONS:
Students/trainees must be provided with the following:
• Waste disposal area
• Oiler
• Handouts for waste management and disposal
• Cleaning chemicals for grease and lubricants
• Containers for waste and used lubricants
METHODOLOGIES:
• Interactive lecture
• Dual training
• Self-paced instruction
• Simulation
• Demonstration
ASSESSMENT METHODS:
• Direct observation
• Simulation
• Written examination
• Interview
LO4. REPORT DAMAGED TOOLS AND EQUIPMENT
ASSESSMENT CRITERIA:
1. Complete inventory of tools and equipment is maintained.
2. Damaged tools/equipment is identified with repair recommendation.
3. Reports prepared on damaged tools/equipment have no error/discrepancy.
CONTENTS:
• Conducting inventory and preparing records
• Maintenance and safe handling of tools and equipment
• Maintenance and updating of records and reports
CONDITIONS:
• Records and inventory of tools and equipment
• Record books
• Checklist
• Waste disposal reports
• Racks for tools
METHODOLOGIES:
• Interactive lecture
• Dual Training
• Self-paced instruction
• Simulation
ASSESSMENT METHODS:
• Interview
• Written examination
• Demonstration
• Direct observation
MODULES OF INSTRUCTION
CORE COMPETENCIES
AUTOMOTIVE MECHANICAL ASSEMBLY NC II
UNIT OF COMPETENCY : ASSEMBLE MECHANICAL ASSEMBLIES USING JIGS/FIXTURES
MODULE TITLE : ASSEMBLING MECHANICAL ASSEMBLIES USING JIGS/FIXTURES
MODULE DESCRIPTOR : This module covers the assembling of mechanical assemblies using jigs/fixtures for installing/mounting to automotive vehicle body in accordance with company standards.
NOMINAL DURATION : 15 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Obtain materials/parts for the job
LO2. Select and use tools and equipment
LO3. Load/unload parts into assembly jigs/fixtures
LO4. Select and use hardware parts
LO5. Assemble mechanical assemblies
LO1. OBTAIN MATERIALS/PARTS FOR THE JOB
ASSESSMENT CRITERIA:
1. Materials/parts list is read and interpreted to establish requirements for the job.
2. Parts/materials are picked by matching part numbers that are stacked in the warehouse bin/container and floor stack areas.
3. Parts/materials are delivered to respective point of fit to ensure smooth and continuous production.
CONTENTS:
• Identification and interpretation of engineering manuals and Materials/parts list used in obtaining parts and materials
• Particular application or use of material handling equipment
• Identification of point of fit in the assembly line
• Handling standard for parts and materials
CONDITION:
Students/trainees must be provided with the following:
• Material handling equipment
o Forklift
o Hand pallet truck
o Tow motor
• Materials/parts list
• Vehicle assembly manual
• Assembly line layout
• PPE
o Safety shoes
o Gloves
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO2. SELECT AND USE TOOLS AND EQUIPMENT
ASSESSMENT CRITERIA:
1. Appropriate tools and equipment are selected to meet job requirement.
2. Impact guns and torque wrenches are checked and calibrated to ensure they are in good working order.
3. Lifting equipment are evaluated for appropriate use in accordance with OH&S requirements
CONTENTS:
• Torque calibration and maintenance system
• Handling standard for defective tools
• Safe practice in using lifting equipment
CONDITION:
Students/trainees must be provided with the following:
• Hand tools
• Torque wrenches
• Impact gun
• Lifting equipment
• Engineering manuals
• PPE
o Safety shoes
o Gloves
o Hard hat
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO3. LOAD/UNLOAD PARTS INTO ASSEMBLY JIGS/FIXTURES
ASSESSMENT CRITERIA:
1. Parts are matched to the jigging equipment reference to part numbers and codes.
2. Parts are securely clamped to prevent movement and distortion during the assembly operation as specified in the standard operation sheet.
CONTENTS:
• Correct sequence of parts loading to assembly jig
• Sequence of Jig clamping
CONDITION:
Students/trainees must be provided with the following:
• Assembly Jigs/fixtures
• Hand tools
• Lifting equipment
• Torque wrenches
• Impact gun
• Engineering manuals
• Parts for mechanical assemblies
• PPE
o Safety shoes
o Gloves
o Hard hat
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO4. SELECT AND USE HARDWARE PARTS
ASSESSMENT CRITERIA:
1. Hardware parts are identified and selected to meet the job requirements as stated in the materials/parts list.
2. Hardware parts are fitted in the required number to the designated positions stated in the materials/parts list and engineering manuals.
CONTENTS:
• Hardware parts differentiation and classification
• Identification and interpretation of engineering manuals and Materials/parts list used in obtaining hardware parts.
• Handling standard for hardware parts
CONDITION:
Students/trainees must be provided with the following:
• Engineering manuals
• Materials/parts list
• Hand tools
• Impact gun
• Torque wrenches
• Hardware or small parts
• PPE
o Safety shoes
o Gloves
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO5. ASSEMBLE MECHANICAL ASSEMBLIES
ASSESSMENT CRITERIA:
1. Materials/parts list and engineering drawings are correctly read and interpreted.
2. Parts are matched with the materials/parts list for the particular requirements for the job.
3. Parts are positioned and secured in accordance with the assembly manuals
4. Specified nuts, bolts and screws are tensioned to the specified torque requirements
5. Identified faults are recorded, reported and rectified/scrapped in accordance with company procedures.
6. Workflow and output are recorded and maintained.
CONTENTS:
• Proper use of torque wrench
• Proper use of impact gun
• Tightening sequence
• Handling standard of parts and assemblies
• Production control
CONDITION:
Students/trainees must be provided with the following:
• Impact gun
• Torque wrench
• Hand tools
• Lifting equipment
• Engineering manuals
• PPE (safety shoes, gloves, hard hat, ear plug)
• Hardware or small parts
• Mechanical parts for sub-assembly includes but not limited to:
➢ Suspension assembly
• Coil spring
• Shock absorber
• Suspension bushing
• Metal parts/components
➢ Power drive assembly
• Bare Engine assembly
• Transmission assembly
• Pressure plate
• Clutch disc
• Intake and exhaust manifold
• Primary muffler
• Catalytic converter
• Air conditioning compressor
• Belt drive
➢ Fuel tank assembly
• Fuel tank
• Floater
• Pump
➢ Brake, clutch and accelerator pedals assembly
• Bracket
• Pedal and bushing
➢ Radiator cooling system assembly
• Radiator
• Metal brackets
• Inlet, outlet and return water hoses
➢ Air conditioning system
• Condenser assembly
• Expansion valve
• Evaporator assembly
• Evaporator housing
➢ Front and rear bumpers assembly
• Bumper fascia
• Insulation
➢ Wheel assembly
• Tires
• Steel or aluminum alloy rim
• Tire valve
➢ Windshield and door glasses assembly
• Dam rubber kit
• Door glass holders
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
UNIT OF COMPETENCY : MOUNT/INSTALL BRAKE AND FUEL SYSTEMS
MODULE TITLE : MOUNTING/INSTALLING BRAKE AND FUEL SYSTEMS
MODULE DESCRIPTOR : This module covers mounting/installing assemblies and parts of brake and fuel system to automotive vehicle body in accordance with company standards.
NOMINAL DURATION : 15 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Select and use tools and equipment
LO2. Select and use hardware parts
LO3. Mount/install assemblies and parts
LO4. Route service lines
LO1. SELECT AND USE TOOLS AND EQUIPMENT
ASSESSMENT CRITERIA:
1. Tools and equipment are selected to meet job requirements.
2. Tools and equipment are checked to ensure they are in good working order.
3. Appropriate lifting hoist/hangers/gears are selected and used in accordance with OH&S requirements.
CONTENTS:
• Torque calibration and maintenance system
• Handling standard for defective tools
• Safe practice in using lifting equipment
CONDITION:
Students/trainees must be provided with the following:
• Hand tools
• Torque wrenches
• Impact gun
• Lifting equipment
• Engineering manuals
• PPE
o Safety shoes
o Gloves
o Hard hat
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO2. SELECT AND USE HARDWARE PARTS
ASSESSMENT CRITERIA:
1. Hardware parts are identified and selected to meet the job requirements as stated in the materials/parts list.
2. Hardware parts are fitted in the required number to the designated positions stated in the materials/parts list and engineering manuals.
CONTENTS:
• Hardware parts differentiation and classification
• Identification and interpretation of engineering manuals and Materials/parts list used in obtaining hardware parts.
• Handling standard for hardware parts
CONDITION:
Students/trainees must be provided with the following:
• Engineering manuals
• Materials/parts list
• Hand tools
• Torque wrenches
• Impact gun
• Hardware or small parts
• PPE
o Safety shoes
o Gloves
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO3. MOUNT/INSTALL ASSEMBLIES AND PARTS
ASSESSMENT CRITERIA:
1. Materials/parts list and engineering drawings are correctly read and interpreted.
2. Parts/components are matched with the materials/parts list for the particular requirements for the job.
3. Assemblies and parts are positioned and secured into automotive vehicle body as per the relevant drawings and standard operation sheet.
4. Specified nuts, bolts and screws are tensioned to the specified torque requirements stated in the engineering manuals and standard operating sheet.
5. Identified faults are recorded, reported and rectified/scrapped in accordance with company procedures.
CONTENTS:
• Proper use of torque wrench
• Proper use of impact gun
• Tightening sequence
• Handling standard of parts and assemblies
• Production control
CONDITION:
Students/trainees must be provided with the following:
• Impact gun
• Torque wrench
• Lifting equipment
• Hand tools
• Engineering manuals
• Hardware or small parts
• Assemblies and parts of brake and fluid systems
• Automotive vehicle body
• Mechanical assemblies include but not limited to:
o Fuel tank assembly
o Brake pedal assembly
o Clutch pedal assembly
o Accelerator pedal assembly
• Mechanical parts include but not limited to:
o Fuel filter
o Brake booster
o Brake master cylinder
o Brake and fuel pipes
o Brake and fuel valves
o Brake disc
o Anti brake system kit
o Brake drum
• PPE
o Safety shoes
o Gloves
o Hard hat
o Ear plug
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO4. ROUTE SERVICE LINES
ASSESSMENT CRITERIA:
1. Materials/parts list and engineering manuals are correctly read and interpreted.
2. Appropriate hardware parts are selected and used according to specifications.
3. Service lines are routed, tied and clipped to specification.
4. Workflow and production output are recorded and maintained.
CONTENT:
• Vehicle safety and fire prevention
CONDITION:
Students/trainees must be provided with the following:
• Impact gun
• Torque wrench
• Hand tools
• Engineering manuals
• Automotive vehicle body
• Hardware or small parts
• PPE
o Safety shoes
o Gloves
o Hard hat
o Ear plug
o goggles
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
UNIT OF COMPETENCY : MOUNT/INSTALL POWER DRIVE SYSTEM
MODULE TITLE : MOUNTING/INSTALLING POWER DRIVE SYSTEM
MODULE DESCRIPTOR : This module covers mounting/installing assemblies and parts of power drive system to automotive vehicle body in accordance with company standards.
NOMINAL DURATION : 15 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Select and use tools and equipment
LO2. Select and use hardware parts
LO3. Mount/install assemblies and parts
LO4. Route service lines
LO1. SELECT AND USE TOOLS AND EQUIPMENT
ASSESSMENT CRITERIA:
1. Tools and equipment are selected to meet job requirements.
2. Tools and equipment are checked to ensure they are in good working order
3. Appropriate lifting hoist/hangers/gears are selected and used in accordance with OH&S requirements.
CONTENTS:
• Torque calibration and maintenance system
• Handling standard for defective tools
• Safe practice in using lifting equipment
CONDITION:
Students/trainees must be provided with the following:
• Hand tools
• Torque wrenches
• Impact gun
• Lifting equipment
• Engineering manuals
• PPE
o Safety shoes
o Gloves
o Hard hat
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO2. SELECT AND USE HARDWARE PARTS
ASSESSMENT CRITERIA:
1. Hardware parts are identified and selected to meet the job requirements as stated in the materials/parts list.
2. Hardware parts are fitted in the required number to the designated positions stated in the materials/parts list and engineering manuals.
CONTENTS:
• Hardware parts differentiation and classification
• Identification and interpretation of engineering manuals and Materials/parts list used in obtaining hardware parts.
• Handling standard for hardware parts
CONDITION:
Students/trainees must be provided with the following:
• Engineering manuals
• Materials/parts list
• Hand tools
• Torque wrenches
• Impact gun
• Hardware or small parts
• PPE
o Safety shoes
o Gloves
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO3. MOUNT/INSTALL ASSEMBLIES AND PARTS
ASSESSMENT CRITERIA:
1. Materials/parts list and engineering drawings are correctly read and interpreted.
2. Parts/components are matched with the materials/parts list for the particular requirements for the job.
3. Assemblies and parts are positioned and secured into automotive vehicle body as per the relevant drawings and standard operation sheet.
4. Specified nuts, bolts and screws are tensioned to the specified torque requirements stated in the engineering manuals and standard operating sheet.
5. Identified faults are recorded, reported and rectified/scrapped in accordance with company procedures.
CONTENTS:
• Proper use of torque wrench
• Proper use of impact gun
• Tightening sequence
• Handling standard of parts and assemblies
• Production control
CONDITION:
Students/trainees must be provided with the following:
• Impact gun
• Torque wrench
• Lifting equipment
• Hand tools
• Engineering manuals
• Hardware or small parts
• Mechanical assemblies include but not limited to:
o Engine sub-assembly with transmission
• Mechanical parts include but not limited to:
o Engine support
o Transmission support
o Propeller shaft and differential
• Automotive vehicle body
• PPE
o Safety shoes
o Gloves
o Hard hat
o Ear plug
o goggles
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO4. ROUTE SERVICE LINES
ASSESSMENT CRITERIA:
1. Materials/parts list and engineering manuals are correctly read and interpreted.
2. Appropriate hardware parts are selected and used according to specifications.
3. Service lines are routed, tied and clipped to specification.
4. Workflow and production output are recorded and maintained.
CONTENTS:
• Service line installation
• Vehicle safety and fire prevention
CONDITION:
Students/trainees must be provided with the following:
• Impact gun
• Torque wrench
• Hand tools
• Engineering manuals
• Hardware or small parts
• Automotive vehicle body
• PPE
o Safety shoes
o Gloves
o Hard hat
o Ear plug
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
UNIT OF COMPETENCY : MOUNT/INSTALL SUSPENSION DRIVE TRAIN
MODULE TITLE : MOUNTING/INSTALLING SUSPENSION DRIVE TRAIN
MODULE DESCRIPTOR : This module covers mounting/installing assemblies and parts of suspension drive train to automotive vehicle body in accordance with company standards
NOMINAL DURATION : 15 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Select and use tools and equipment
LO2. Select and use hardware parts
LO3. Mount/install assemblies and parts
LO1. SELECT AND USE TOOLS AND EQUIPMENT
ASSESSMENT CRITERIA:
1. Tools and equipment are selected to meet job requirements.
2. Tools and equipment are checked to ensure they are in good working order.
3. Appropriate lifting hoist/hangers/gears are selected and used in accordance with OH&S requirements.
CONTENTS:
• Torque calibration and maintenance system
• Handling standard for defective tools
• Safe practice in using lifting equipment
CONDITION:
Students/trainees must be provided with the following:
• Hand tools
• Torque wrenches
• Impact gun
• Lifting equipment
• Engineering manuals
• PPE
o Safety shoes
o Gloves
o Hard hat
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO2. SELECT AND USE HARDWARE PARTS
ASSESSMENT CRITERIA:
1. Hardware parts are identified and selected to meet the job requirements as stated in the materials/parts list.
2. Hardware parts are fitted in the required number to the designated positions stated in the materials/parts list and engineering manuals.
CONTENTS:
• Hardware parts differentiation and classification
• Identification and interpretation of engineering manuals and Materials/parts list used in obtaining hardware parts.
• Handling standard for hardware parts
CONDITION:
Students/trainees must be provided with the following:
• Engineering manuals
• Materials/parts list
• Hand tools
• Torque wrenches
• Impact gun
• Hardware or small parts
• PPE
o Safety shoes
o Gloves
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO3. MOUNT/INSTALL ASSEMBLIES AND PARTS
ASSESSMENT CRITERIA:
1. Materials/parts list and engineering drawings are correctly read and interpreted.
2. Parts/components are matched with the materials/parts list for the particular requirements for the job.
3. Assemblies and parts are positioned and secured into automotive vehicle body as per the relevant drawings and standard operation sheet.
4. Specified nuts, bolts and screws are tensioned to the specified torque requirements stated in the engineering manuals and standard operating sheet
5. Identified faults are recorded, reported and rectified/scrapped in accordance with company procedures.
6. Workflow and production output are recorded and maintained
CONTENTS:
• Proper use of torque wrench
• Proper use of impact gun
• Tightening sequence
• Handling standard of parts and assemblies
• Production control
CONDITION:
Students/trainees must be provided with the following:
• Impact gun
• Torque wrench
• Lifting equipment
• Hand tools
• Engineering manuals
• Hardware or small parts
• Mechanical Assemblies may include but not limited to:
o Suspension
o Wheel assembly
o Steering assembly system – gear box or rack and pinion type
• Mechanical parts may include but not limited to:
o Axle drive
o Rotor disc
o Stabilizer bars
o Torsion bars
• Automotive vehicle body
• PPE
o Safety shoes
o Gloves
o Hard hat
o Ear plug
o goggles
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
UNIT OF COMPETENCY : INSTALL/FIT OUT TRIM PARTS AND ASSEMBLIES
MODULE TITLE : INSTALLING/FITTING OUT TRIM PARTS AND ASSEMBLIES
MODULE DESCRIPTOR : This module covers installing/fitting out trim parts and assemblies to automotive vehicle body in accordance with company standards.
NOMINAL DURATION : 15 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Select and use tools and equipment
LO2. Select and use hardware parts
LO3. Install/fit out assemblies and parts
LO4. Select and use adhesives, sealants and solvents
LO1. SELECT AND USE TOOLS AND EQUIPMENT
ASSESSMENT CRITERIA:
1. Tools and equipment are selected to meet job requirements.
2. Tools and equipment are checked to ensure they are in good working order
3. Appropriate lifting hoist/hangers/gears are selected and used in accordance with OH&S requirements.
CONTENTS:
• Torque calibration and maintenance system
• Handling standard for defective tools
• Safe practice in using lifting equipment
CONDITION:
Students/trainees must be provided with the following:
• Hand tools
• Torque wrenches
• Impact gun
• Lifting equipment
• Engineering manuals
• PPE
o Safety shoes
o Gloves
o Hard hat
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO2. SELECT AND USE HARDWARE PARTS
ASSESSMENT CRITERIA:
1. Hardware parts are identified and selected to meet the job requirements as stated in the materials/parts list.
2. Hardware parts are fitted in the required number to the designated positions stated in the materials/parts list and engineering manuals.
CONTENTS:
• Hardware parts differentiation and classification
• Identification and interpretation of engineering manuals and Materials/parts list used in obtaining hardware parts.
• Handling standard for hardware parts
CONDITION:
Students/trainees must be provided with the following:
• Engineering manuals
• Materials/parts list
• Hand tools
• Torque wrenches
• Impact gun
• Hardware or small parts
• PPE
o Safety shoes
o Gloves
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO3. INSTALL/FIT OUT ASSEMBLIES AND PARTS
ASSESSMENT CRITERIA:
1. Materials/parts list and engineering drawings are correctly read and interpreted.
2. Parts/components are matched with the materials/parts list for the particular requirements for the job.
3. Assemblies and parts are positioned and secured into automotive vehicle body as per the relevant drawings and standard operation sheet.
4. Specified nuts, bolts and screws are tensioned to the specified torque requirements stated in the engineering manuals and standard operating sheet.
5. Identified faults are recorded, reported and rectified/scrapped in accordance with company procedures.
6. Workflow and production output are recorded and maintained
CONTENTS:
• Proper use of torque wrench
• Proper use of impact gun
• Tightening sequence
• Handling standard of parts and assemblies
• Production control
CONDITION:
Students/trainees must be provided with the following:
• Impact gun
• Torque wrench
• Lifting equipment
• Hand tools
• Engineering manuals
• Hardware or small parts
• Trim assemblies may include but not limited to:
o Door and windshield glasses
o Bumpers
• Trim parts may include but not limited to:
o Floor carpet
o Seats
o Door mechanism and components
o Finishers for ceiling roof, doors and package tray, center and rear pillars
o Moldings
o Garnishes for front, center and rear pillars
o Inner view and side view mirrors
• Automotive vehicle body
• PPE
o Safety shoes
o Gloves
o Hard hat
o Ear plug
o goggles
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO4. SELECT AND USE ADHESIVES, SEALANTS AND SOLVENTS
ASSESSMENT CRITERIA:
1. Adhesives, sealants and solvents are selected and applied to meet quality control standard and job requirements
2. Solvents are selected and used to remove excess adhesives and sealants ensuring finished product meets company quality control standards
3. Major spills are reported to the appropriate safety personnel and cleaned up in accordance with emergency procedures for hazardous materials.
CONTENTS:
• Handling standard of sealants, adhesives and solvents
• Manual application of sealants
CONDITION:
Students/trainees must be provided with the following:
• Impact gun
• Torque wrench
• Lifting equipment
• Hand tools
• Engineering manuals
• Assemblies and parts of suspension drive train
• Automotive vehicle body
• PPE
o Safety shoes
o Gloves
o Hard hat
o Ear plug
o goggles
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
UNIT OF COMPETENCY : PERFORM FINAL ENGINE RUN
MODULE TITLE : PERFORMING FINAL ENGINE RUN
MODULE DESCRIPTOR : This module covers servicing of vehicle after assembly operations. Service includes the addition and/or application of fluids and lubricants and the bleeding of air and hydraulic system in accordance with specifications and company procedures
NOMINAL DURATION : 15 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Select and use tools and equipment
LO2. Select and use Lubricants and fluids
LO3. Bleed air and hydraulic system
LO4. Record and report faults
LO1. SELECT AND USE TOOLS AND EQUIPMENT
ASSESSMENT CRITERIA:
1. Tools and equipment are selected to meet job requirements.
2. Tools and equipment are checked to ensure they are in good working order.
CONTENTS:
• Calibration and maintenance system of dispensing equipment
• Handling standard for defective tools
CONDITION:
Students/trainees must be provided with the following:
• Bleeding tools
• Manual air and hydraulic pressurized lubrication
• Hand tools
• Vehicle protection cover
• Impact gun
• Lifting equipment
• Engineering manuals
• PPE
o Safety shoes
o Gloves
o Hard hat
o Goggles
o Apron
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO2. SELECT AND USE LUBRICANTS AND FLUIDS
ASSESSMENT CRITERIA:
1. Lubricants and fluids are selected and matched to the vehicle by codes and numbers as stated on the lubrication data sheets/material lists.
2. Lubricants and fluids are used on the identified parts of the vehicle as stated on the lubrication data sheets/material lists.
3. Reservoirs and mechanical assemblies are filled with the identified lubricant/fluid to levels specified in the lubrication data sheets.
4. Excess lubricants and fluids are removed in accordance with the company quality control standards.
5. Lubricants and fluids are used in accordance with company OH&S procedures.
CONTENTS:
• Proper use of hydraulic pressurized equipment
• Types and characteristic of lubricants and fluids
• Handling standard for lubricants and fluids
CONDITION:
Students/trainees must be provided with the following:
• Bleeding tools
• Manual air and hydraulic pressurized lubrication
• Hand tools
• Vehicle protection cover
• Impact gun
• Lifting equipment
• Engineering manuals
• Vehicle unit
• PPE (safety shoes, gloves, hard hat, goggles, apron)
• Lubricants and fuels (engine oil, transmission oil, brake fluid, power steering fluid, coolants)
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO3. BLEED AIR AND HYDRAULIC SYSTEM
ASSESSMENT CRITERIA:
1. Bleeding points for air and hydraulic system are located as shown in the engineering manuals.
2. Workflow and production output are recorded and maintained.
CONTENTS:
• Proper bleeding process
• Handling standard of brake fluid
CONDITION:
Students/trainees must be provided with the following:
• Bleeding tools
• Manual air and hydraulic pressurized lubrication
• Hand tools
• Vehicle protection cover
• Impact gun
• Lifting equipment
• Vehicle unit
• Engineering manuals
• PPE
o Safety shoes
o Gloves
o Hard hat
o Goggles
o Apron
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO4. RECORD AND REPORT FAULTS
ASSESSMENT CRITERIA:
1. Appropriate forms are selected for recording and reporting identified faults.
2. Relevant forms are completed and maintained in accordance with company procedures.
3. Faults are reported to appropriate personnel for action.
CONTENTS:
• Proper filling up of forms
• Records maintenance system
CONDITION:
Students/trainees must be provided with the following:
• Company standard form
o Vehicle inspection card
o Quality defect feedback form
• Office supplies- ball pen, pencil, bond paper, markers, clip board
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
UNIT OF COMPETENCY : PERFORM WHEEL ALIGNMENT OPERATIONS
MODULE TITLE : PERFORMING WHEEL ALIGNMENT OPERATIONS
MODULE DESCRIPTOR : This module covers performing wheel alignment operations within the motor vehicle assembly industry.
NOMINAL DURATION : 15 hours
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO1. Prepare for the job
LO2. Perform wheel alignment
LO1. PREPARE FOR THE JOB
ASSESSMENT CRITERIA:
1. Work specification is read and interpreted to determine alignment process.
2. Wheel alignment pre-checks are completed in accordance with company procedures.
3. Tools and equipment are determined and the alignment measuring equipment is connected to the vehicle.
CONTENTS:
• Calibration and maintenance system
• Handling standard for defective tools
CONDITION:
Students/trainees must be provided with the following:
• Bleeding tools
• Manual air and hydraulic pressurized lubrication
• Hand tools
• Vehicle protection cover
• Impact gun
• Lifting equipment
• Engineering manuals
• PPE
o Safety shoes
o Gloves
o Hard hat
o Goggles
o Apron
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
LO2. PERFORM WHEEL ALIGNMENT
ASSESSMENT CRITERIA:
1. Wheel alignment equipment information is accessed and interpreted from manufacturer specifications.
2. Wheel alignment procedures are undertaken in accordance with company procedures.
3. Adjustments are undertaken in accordance with the vehicle and equipment manufacturer’s specifications.
4. Wheel alignment procedures are carried out and documentation completed in accordance with company procedures/policies.
CONTENTS:
• Perform wheel alignment
• Mensuration and calculation
CONDITION:
Students/trainees must be provided with the following:
• Hand tools
• Special tools
• Vehicle protection cover
• Impact gun
• Mechanical equipment
• Laser wheel alignment equipment
• Hydraulic lifter
• Vehicle unit
• Engineering manuals
• PPE
o Safety shoes
o Gloves
o Hard hat
o Goggles
o Apron
METHODOLOGIES:
• Lecture/demonstration
• Dualized training
ASSESSMENT METHODS:
• Observation with questioning
• Demonstration with questioning
• Interview
• Portfolio
ACKNOWLEDGEMENT
We wish to express our appreciation and with particular thanks to the following developers, facilitators and managers of Competency-Based Curriculum in Automotive Mechanical Assembly NC II.
• Technology Experts:
3 Antonio A. Gimenez- Executive Director - CATC/PAFI
- Rodolfo T. Nunez- Plant Manager-Nissan Motors Phils. Inc.(NMPI)
- Edgardo P. Zaragoza- Paint Shop Manager- NMPI
- Mr. Valentino de Leon – VP Plant Administration- NMPI
- Carina J. Bondad- Administrative Support Staff, (CATC/PAFI)
• Facilitators:
4 Florante P. Inoturan
5 Agnes P. Panem
6 Abel B. Elpedes
• The management and staff of the Qualifications and Standards Office.
What is Competency-Based Curriculum (CBC)
❑ A competency-based curriculum is a framework or guide for the subsequent detailed development of competencies, associated methodologies, training and assessment resources.
❑ The CBC specifies the outcomes which are consistent with the requirements of the workplace as agreed through the industry or community consultations.
❑ CBC can be developed immediately when competency standards exist.
❑ When competency standards do not exist, curriculum developers need to clearly define the learning outcomes to be attained. The standard of performance required must be appropriate to industry and occupational needs through the industry/enterprise or specified client group consultations.
These materials are available in both printed and electronic copies.
For more information please contact:
Technical Education and Skills Development Authority (TESDA)
Telephone Nos.: 893-8281, 817-4076 to 82 loc. 611, 630, 631 and 635 or visit our website: .ph or the TESDA Regional or Provincial Office nearest you.
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- 100 free home assembly jobs
- work at home assembly jobs no fees
- top assembly at home companies
- home assembly companies listed with bbb
- assembly room crossword
- mercedes benz assembly plant locations
- right to assembly protest
- free home assembly jobs directory
- assembly line production worker duties
- toyota assembly plant
- assembly jobs at home
- assembly required furniture