Change Notice No. 1



State of Washington

Current Contract Information

Change Notice No. 22

September 1, 2016

|Contract number: |04009 (replaces 09902) |Commodity code: |560-75 |

|Contract title: |Forklifts and Lift Equipment |

|Purpose: |Item addition (effective date: 9/1/2016). |

|Award date: |11/19/2009 |

|Period of performance: |5/01/2016 |through: |10/30/2016 |

|Contract term: |Not to exceed 10/30/2016 | |

|Contract type: |This contract is designated as mandatory use. |

|Scope of Contract: |The purpose of this contract is for the as needed purchase of forklifts, options, accessories, parts, |

| |repair manuals, preventative maintenance agreements in the equipment categories as outlined in the |

| |contract. |

|Primary users: |All State Agencies, Institutions of Higher Education, Political Subdivisions, all members of the |

| |Washington State Purchasing Cooperative (WSPC) and Non-Profit Corporations may utilize this Contract. |

| |This Contract is also available for use by Oregon’s Department of Administrative Services Cooperative |

| |Purchasing Program (ORCPP). |

|Products Available |Materials handling equipment of various capacities and types. |

|Ordering information: |See Appendix D |

|Ordering procedures: |See Appendix D |

|Current participation: |$0.00 MBE |$0.00 WBE |$2,500,000.00 OTHER |$0.00 EXEMPT |

| |MBE 0% |WBE 0% |OTHER 100% |Exempt 0% |

|Recovered Material: |None |

This page contains key contract features. Find detailed information on succeeding pages. For more information on this contract, or if you have any questions, please contact your local agency Purchasing Office, or you may contact our office at the numbers listed below.

|Contract Specialist |Corey A. Larson |

|Phone Number: |(360) 407-9407 |

|Fax Number: |(360) 586-2426 |

|Email: |corey.larson@des. |

Visit our Internet site: des.

Current Contract Information

Change Notice No. 22

Contract No. 04009

Page 2

Contract 04009 contains the following categories of Forklifts and Lift Equipment. Within each category is the Contractor’s name, product information, pricing, options, accessories, parts, repair manuals, preventative maintenance agreements, and extended warranty programs. Contractor information is located in Appendix D.

Pricing for Categories

Category 1: Walk Behind Pallet Jack

Category 2: Riding Pallet Jack

Category 3: Reach/Lift/Stand Up Fork Lift

Category 4: Sit Down 3- Wheel Forklift

Category 5: Sit Down 4- Wheel Forklift

Category 6: Pneumatic Tire Fork Lift

Category 7: Walk Behind Fork Lift

Category 8: Stand Up Fork Lift

Category 9: Stand Up Fork Lift, Counter Balanced

For detailed specifications please use the following links to each Category located in Appendix B.

Note: Batteries and chargers are options. Please consult with the sales representative to determine which units meet your needs before ordering.

Specifications for Categories

Category 1: Walk Behind Pallet Jack

Category 2: Riding Pallet Jack

Category 3: Reach/Lift/Stand Up Fork Lift

Category 4: Sit Down 3- Wheel Forklift

Category 5: Sit Down 4- Wheel Forklift

Category 6: Pneumatic Tire Fork Lift

Category 7: Walk Behind Fork Lift

Category 8: Stand Up Fork Lift

Category 9: Stand Up Fork Lift, Counter Balanced

Current Contract Information

Change Notice No. 22

Contract No. 04009

Page 3

|Order placement address: |See Appendix D |

|Ordering information: |See Appendix D |

|Minimum orders: |None |

|Delivery time: |Various, see Appendix D |

|Terms of sale: |FOB |

| |Contractor Delivery – FOB Destination |

| |Agency Pick Up – FOB Contractor Pick Up Point |

|Payment terms: |See Appendix D |

|Payment address: |See Appendix D |

|Contract pricing: |See Appendix E or refer to Pricing Tab |

|Estimated term worth: |$1,000,000.00/2 yrs. |

Notes:

I. State Agencies: Submit Order directly to the Contractor for processing. Political Subdivisions: Submit orders directly to Contractor referencing State of Washington Contract number. If you are unsure of your status in the Department of Enterprise Services (DES), Master Contracts and Consulting’s Master Contracts Usage Agreement (MCUA) call (360) 407-2210 or visit MCUA.

II. Only authorized purchasers included in the MCUA by DES may purchase from this contract. It is the contractor’s responsibility to verify membership of these organizations prior to processing orders received under this contract. A list of Washington members is available on the Internet MCUA List. Contractors shall not process state contract orders from unauthorized users.

III. Contract Terms: This Document includes by reference all terms and conditions published in the original IFB, including Standard Terms and Conditions, and Definitions, included in the Competitive Procurement Standards published by MCC (as Amended).

Special Conditions:

1. Current Contract Information (CCI) (9/1/2016) This Current Contract Information (Change Notice No. 22) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 and hereby allows a model change and an options list for Category 4, Sit Down Fork Lift, 3-Wheel, Electric, 3,500 lbs. For pricing see Appendix D and for specifications see Category 4. All other terms and conditions remain unchanged.

2. Current Contract Information (CCI) (7/20/2016) This Current Contract Information (Change Notice No. 21) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 and hereby allows the following item addition; Category 6, Pneumatic Tire, Sit Down Fork Lift, 4-Wheel, Electric, 4,000 lbs. and an options list. For pricing see Appendix D and for specifications see Category 6. All other terms and conditions remain unchanged.

Current Contract Information

Change Notice No. 22

Contract No. 04009

Page 4

3. Current Contract Information (CCI) (6/3/2016) This Current Contract Information (Change Notice No. 20) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 and hereby allows the following item addition; Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 12,000 lbs. and an options list. For pricing see Appendix D and for specifications see Category 5. All other terms and conditions remain unchanged.

4. Current Contract Information (CCI) (4/06/2016) This Current Contract Information (Change Notice No. 19) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 and hereby allows an interim extension of the contract (6) months from 5/01/2016 through 10/30/2016 or until contract 06115 is in place.

5. Current Contract Information (CCI) (3/3/2016) This Current Contract Information (Change Notice No. 18) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 and hereby allows the following item addition; Category 6, Pneumatic Tire Sit Down Fork Lift, Diesel, 4,000 lbs, Tier-4 Final and an options list. For pricing see Appendix D and for specifications see Category 6. All other terms and conditions remain unchanged.

6. Current Contract Information (CCI) (11/30/2015) This Current Contract Information (Change Notice No. 17) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 and hereby allows the contract to be extended for a period of four (4) months from 12/01/2015 through 4/30/2016. An options list has been added for Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 3,500 lbs. All other terms and conditions remain unchanged.

7. Current Contract Information (CCI) (6/23/2015) This Current Contract Information (Change Notice No. 16) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby adds an new item with options to: Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 11,000 lbs. For pricing see Appendix D and for specifications see Category 6: All other terms conditions and pricing remain unchanged.

8. Current Contract Information (CCI) (5/22/2015) This Current Contract Information (Change Notice No. 15) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby allows a model update and adds an options list to: Category 3, Reach/Lift/Stand up Fork Lift, Electric, 3,500 lbs. For pricing see Appendix D and for specifications see Category 3. All other terms conditions and pricing remain unchanged.

9. Current Contract Information (CCI) (5/08/2015) This Current Contract Information (Change Notice No. 14) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby allows a model update and adds an options list to: Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 10,000 lbs. For pricing see Appendix D and for specifications see Category 6. All other terms conditions and pricing remain unchanged.

Current Contract Information

Change Notice No. 22

Contract No. 04009

Page 5

10. Current Contract Information (CCI) (1/30/2015) This Current Contract Information (Change Notice No. 13) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby adds a Stand Up Fork Lift, Counter Balanced, Electric, 5,000 lbs. with options to Category 9. The Raymond Model 4200 has been discontinued by the manufacturer and is being replaced with a Raymond Model 4250. For pricing see Appendix D and for specifications see Category 9: All other terms conditions and pricing remain unchanged.

11. Current Contract Information (CCI) (1/14/2015) This Current Contract Information (Change Notice No. 12) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby adds a Pneumatic Tire Sit Down Fork Lift, Diesel, 8,000 lbs. and, a Pneumatic Tire Sit Down Forklift LPG, 8,000 lbs. with options to Category 6. For pricing see Appendix D and for specifications see Category 6: All other terms conditions and pricing remain unchanged.

12. Current Contract Information (CCI) (11/03/2014) This Current Contract Information (Change Notice No. 11) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby adds options to: Category 4, Sit Down Fork Lift, 3-Wheel, Electric, 4,000 lbs. For pricing see Appendix D and for specifications see Category 4: All other terms conditions and pricing remain unchanged.

13. Current Contract Information (CCI) (11/26/2013) This Current Contract Information (Change Notice No. 10) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby allows the contract to be extended for a period of twenty-four (24) months from 12/01/2013 through 11/30/2015. All other terms and conditions remain unchanged.

14. Current Contract Information (CCI) (10/31/2013) This Current Contract Information (Change Notice No. 9) is to advise of administrative updates with regard to the MCUA and Best Buy in the NOTES section above and, incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby adds the following item: Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 6,500 lbs. For pricing see Appendix D and for specifications, see Category.6. All other terms conditions and pricing remain unchanged.

15. Current Contract Information (CCI) (9/16/2013) This Current Contract Information (Change Notice No. 8) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 allows for a pass through price increase of 2.0% to Toyota Lift Northwest for the following items: Categories 4, 5 & 6. All other terms conditions and pricing remain unchanged.

16. Current Contract Information (CCI) (02/07/2013) This Current Contract Information (Change Notice No. 7) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby adds the following item: Category 5, Sit Down Fork Lift, 4-Wheel Electric, 7,000 lbs. For pricing see Appendix D and for specifications see Category 5: All other terms conditions and pricing remain unchanged.

Current Contract Information

Change Notice No. 22

Contract No. 04009

Page 6

17. Current Contract Information (CCI) (8/14/2012) This Current Contract Information (Change Notice No. 6) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 allows for a pass through price increase of 3.0% to Toyota Lift Northwest for the following items: Categories 4, 5 & 6. All other terms conditions and pricing remain unchanged.

18. Current Contract Information (CCI) (11/22/2011) This Current Contract Information (Change Notice No. 5) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby allows the contract to be extended for a period of twenty-four (24) months from 12/01/2011 through 11/30/2013. Also, this Current Contract Information allows for a pass through price adjustment to Pape’ Material Handing in Categories 2, 3, 7 & 8 and to Raymond Handling Concepts in Category 9. See price pages for details.

All other terms and conditions remain unchanged.

19. Current Contract Information (CCI) (05/10/2011) This Current Contract Information (Change Notice No. 4) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby allows for following item addition: Category 6, Pneumatic Tire Sit Down Fork Lift, Diesel, 4,000 lbs. For pricing see Appendix D and for specifications see Category 6: Also, this Current Contract Information allows for a pass through price increase of 4.5% to Toyota Lift Northwest for the following items: Categories 4, 5 & 6. Note: model numbers have been updated in Category 5 for the 5,000 and 6,000 lb. units. All other terms conditions and pricing remain unchanged.

20. Current Contract Information (CCI) (07/06/2010) This Current Contract Information (Change Notice No. 3) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby adds the following item: Category 8, Stand up Fork Lift, 4,000 lbs. For pricing see Appendix D and for specifications see Category 8: All other terms conditions and pricing remain unchanged.

21. Current Contract Information (CCI) (04/10/2010) This Current Contract Information (Change Notice No. 2) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and; hereby removes Mid Columbia Forklift doing business as MidCo Material Handling from the contract by termination for convenience. All contract items have been re-awarded to the next lowest responsive responsible bidders as follows:

Toyota Lift Northwest has been awarded Category 4 and Category 5. Raymond Handling Concepts has been awarded Category 9. Pape’ Material Handling’s contact has been changed from Mike J. Kramer to Martin J. Miller. All other terms conditions and pricing remain unchanged.

22. (12/23/2009) This Current Contract Information (Change Notice No. 1) incorporates the original award and is subject to the Standard Terms and Conditions contained in the original IFB 04009 to include Special Provisions listed below and hereby adds the following item: Category 6, Pneumatic Tire Sit Down Fork Lift, 15,500 lbs. For pricing see Appendix D and for specifications see Category 6: Also, the commodity code has been changed to 3930. All other terms conditions and pricing remain unchanged.

APPENDIX B SPECIFICATIONS

Minimum specifications called for

Category 1, Walk Behind Pallet Jack, Electric, 4,500 lbs.

Vendor: North West Handling Systems, Inc.

| |Description |Check If As Specified|Describe Fully If Not|

| | |Or Exceeds |As Specified |

|1. |Basic capacity: minimum of 4,500 lbs. at 24” load center |x | |

|2. |Fork length: 48” |x | |

|3. |Fork overall width: 27” |x | |

|4. |Opening between forks: minimum of 12” |x | |

|5. |Lowered height of forks not to exceed 3.25” |x | |

|6. |Lift travel not less than 6” with an overall elevated fork height minimum of 9.25” |x | |

|7. |Pallet enter rollers |x | |

|8. |Unit overall length: not to exceed 82” |x | |

|9. |Unit overall width: not to exceed 33” |x | |

|10. |Gross maximum weight without battery: not to exceed 850 lbs. |x | |

|11. |Maximum travel speed with full load: 2.4 mph |x | |

|12. |Drive wheels, rubber, approximate size: 10” x 5” |x | |

|13. |Load wheels: poly, approximate size: 3.25” x 5” |x | |

|14. |Solid state controlled electrical system |x | |

|15. |Proportional plugging |x | |

|16. |Brakes: mechanical disc or drum |x | |

|17. |Built-in 110 volt battery charger |x | |

|18. |Battery: 24 volt |x | |

|19. |Battery discharge indicator/meter |x | |

|20. |Hour meter |x | |

|21. |Multi-function controls with twist grip speed control, directional reversing and dead man |x | |

| |brake. | | |

|22. |Lift/lower button |x | |

|23. |On/off power switch |x | |

|24. |Horn |x | |

|25. |Lubrication fittings at pivot points |x | |

|26. |SB-175 connector |x | |

|27. |Owner’s manual |x | |

|28. |Basic warranty: |x | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 1, Walk Behind Pallet Jack, Electric, 6,000 lbs.

Vendor: North West Handling Systems, Inc.

| |Description |Check If As Specified|Describe Fully If Not|

| | |Or Exceeds |As Specified |

|1. |Basic capacity: minimum of 6,000 lbs. at 24” load center |x | |

|2. |Fork length: 48” |x | |

|3. |Fork overall width: 27” |x | |

|4. |Opening between forks: minimum of 9” |x | |

|5. |Lowered height of forks not to exceed 3.25” |x | |

|6. |Lift travel not less than 6” with an overall elevated fork height minimum of 9.25” |x | |

|7. |Pallet enter rollers |x | |

|8. |Unit overall length: not to exceed 82” |x | |

|9. |Unit overall width: not to exceed 33” |x | |

|10. |Gross maximum weight without battery: not to exceed 1,060 lbs. |x | |

|11. |Maximum travel speed with full load: 2.4 mph |x | |

|12. |Drive wheels, rubber, approximate size: 10” x 5” |x | |

|13. |Load wheels: poly, approximate size: 3.25” x 5.75” |x | |

|14. |Solid state controlled electrical system |x | |

|15. |Proportional plugging |x | |

|16. |Brakes: mechanical disc or drum |x | |

|17. |Battery power: 24 volt |x | |

|18. |Battery discharge indicator/meter |x | |

|19. |Hour meter |x | |

|20. |Multi-function controls with twist grip speed control, directional reversing and dead man |x | |

| |brake. | | |

|21. |Lift/lower button |x | |

|22. |On/off power switch |x | |

|23. |Horn |x | |

|24. |Lubrication fittings at pivot points |x | |

|25. |SB-175 connector |x | |

|26. |Owner’s manual |x | |

|27. |Basic warranty: |x | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 2, Riding Pallet Jack, End Control, Electric, 6,000 lbs.

Vendor: Pape’ Material Handling

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 6,000 lbs. at 24” load center |X | |

|2. |Fork length: 48” |X | |

|3. |Fork width: 27” |X | |

|4. |Opening between forks: minimum of 9” |X | |

|5. |Lowered height of forks not to exceed 3.25” |X | |

|6. |Lift travel not less than 6” with an overall elevated fork height minimum of 9.25” |X | |

|7. |Pallet enter rollers |X | |

|8. |Gross weight maximum without battery: 1,250 lbs. |X | |

|9. |Maximum travel speed with full load: 5 mph |X | |

|10. |Drive wheels, rubber, approximate size: 10” x 4.5” |X | |

|11. |Load wheels, poly, approximate size: 3.25” x 5.75” |X | |

|12. |Load stabilizing casters, spring loaded poly, approximate size: 4” x 2.5” |X | |

|13. |Solid state controlled electrical system |X | |

|14. |Top mounted steering handle with operating controls in handle |X | |

|15 |Operator grab bar/handle with operating controls in handle |X | |

|16. |Proportional plugging |X | |

|17. |Brakes: mechanical disc or drum |X | |

|18. |Dual lift cylinders |X | |

|19. |Battery power: 24 volt |X | |

|20. |Battery discharge indicator/meter |X | |

|21. |Hour meter |X | |

|22. |Operator platform approximate height: 9.9” |X | |

|23. |Cushioned floor pad |X | |

|24. |Multi-function controls with twist grip speed control, directional reversing and dead man brake. |X | |

|25. |Lift/lower button |X | |

|26 |On/off power switch |X | |

|27. |Horn |X | |

|28. |Lubrication fittings at pivot points |X | |

|29. |SB-175 connector |X | |

|30. |Owner’s manual |X | |

|31. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 2, Riding Pallet Jack, End Control, Electric, 8,000 lbs.

Vendor: Pape’ Material Handling

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 8,000 lbs. at 24” load center |X | |

|2. |Fork length: 48” |X | |

|3. |Fork width: 27” |X | |

|4. |Opening between forks: minimum of 9” |X | |

|5. |Lowered height of forks not to exceed 3.25” |X | |

|6. |Lift travel not less than 6” with an overall elevated fork height minimum of 9.25” |X | |

|7. |Pallet enter rollers |X | |

|8. |Gross weight maximum without battery: 1,400 lbs. |X | |

|9. |Maximum travel speed with full load: 5 mph |X | |

|10. |Drive wheels, rubber, approximate size: 10” x 4.5” |X | |

|11. |Load wheels, poly, approximate size: 3.25” x 5.75” |X | |

|12. |Load stabilizing casters, spring loaded poly, approximate size: 4” x 2.5” |X | |

|13. |Solid state controlled electrical system |X | |

|14. |Top mounted steering handle with operating controls in handle |X | |

|15 |Operator grab bar/handle with operating controls in handle |X | |

|16. |Proportional plugging |X | |

|17. |Brakes: mechanical disc or drum |X | |

|18. |Dual lift cylinders |X | |

|19. |Battery power: 24 volt |X | |

|20. |Battery discharge indicator/meter |X | |

|21. |Hour meter |X | |

|22. |Operator platform approximate height: 9.9” |X | |

|23. |Cushioned floor pad |X | |

|24. |Multi-function controls with twist grip speed control, directional reversing and dead man brake. |X | |

|25. |Lift/lower button |X | |

|26. |On/off power switch |X | |

|27. |Horn |X | |

|28. |Lubrication fittings at pivot points |X | |

|29. |SB-175 connector |X | |

|30. |Owner’s manual |X | |

|31. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 3, Reach/Lift/Stand up Fork Lift, Electric, 3,000 lbs.

Vendor: Pape’ Material Handling

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 3,000 lbs. at 24” load center |X | |

|2. |Standard forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 210”, not to exceed 220” |X | |

|5. |Maximum load lifting speeds, fully variable: 60 fpm |X | |

|6. |Truck overall collapse height: not to exceed 95” |X | |

|7. |Maximum travel speed with full load: 6.5 mph |X | |

|8. |Side shift |X | |

|9. |Up and down function controls |X | |

|10. |Reach in – out minimum: 23” |X | |

|11. |Tilt: 3 degrees forward and 4 degrees backwards |X | |

|12. |Gross weight maximum without battery: 6,850 lbs. |X | |

|13. |Overhead guard not to exceed 95” |X | |

|14. |Total body width not to exceed 41” |X | |

|15. |Base leg opening: no less than 28” ID and OD not to exceed 40” |X | |

|16. |Operator restraint system |X | |

|17. |Solid state controlled electrical system |X | |

|18. |Steering: hydrostatic |X | |

|19. |Brakes: mechanical disc or drum |X | |

|20. |Proportional plugging |X | |

|21. |Load stabilizing caster, soft poly, approximate size: 7” x 2.75” |X | |

|22. |Drive tire: rubber, approximate size: 13.5” x 5” |X | |

|23. |Load wheels: poly, approximate size: 5” x 4” |X | |

|24. |Battery power: 24 volt |X | |

|25. |Battery discharge indicator/meter |X | |

|26. |Hour meter |X | |

|27. |Top mounted steering handle with twist grip with speed control |X | |

|28. |Lift/lower button |X | |

|29 |On/off power switch |X | |

|30. |Horn |X | |

|31. |Lubrication fittings at pivot points |X | |

|32. |SB-175 connector |X | |

|33. |Owner’s manual |X | |

|34. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 3, Reach/Lift/Stand up Fork Lift, Electric,3,500 lbs.

Vendor: Pape’ Material Handling

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 3,500 lbs. at 24” load center |X | |

|2. |Standard forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 210”, not to exceed 220” |X | |

|5. |Maximum load lifting speeds, fully variable: 40 fpm |X | |

|6. |Truck overall collapse height: not to exceed 95” |X | |

|7. |Maximum travel speed with full load: 5 mph |X | |

|8. |Side shift |X | |

|9. |Up and down function controls |X | |

|10. |Reach in – out minimum: 23” |X | |

|11. |Tilt: 3 degrees forward and 4 degrees backwards |X | |

|12. |Gross weight maximum without battery: 5,150 lbs. |X | |

|13. |Top mounted steering handle |X | |

|14. |Overhead guard not to exceed 95” |X | |

|15. |Total body width not to exceed 41” |X | |

|16. |Base leg opening: no less than 28” ID and OD not to exceed 40” |X | |

|17. |Operator restraint system |X | |

|18. |Solid state controlled electrical system |X | |

|19. |Steering: hydrostatic |X | |

|20. |Brakes: mechanical disc or drum |X | |

|21. |Proportional plugging |X | |

|22. |Load stabilizing caster, soft poly, approximate size:7” x 2.75” |X | |

|23. |Drive tire: rubber, approximate size: 13.5” x 5” |X | |

|24. |Load wheels: poly, approximate size: 5” x 4” |X | |

|25. |Battery power: 24 volt |X | |

|26. |Battery discharge indicator/meter |X | |

|27. |Hour meter |X | |

|28. |Top mounted steering handle with twist grip with speed control |X | |

|29 |Lift/lower button |X | |

|30. |On/off power switch |X | |

|31. |Horn |X | |

|32. |Lubrication fittings at pivot points |X | |

|33. |SB-175 connector |X | |

|34. |Owner’s manual |X | |

|35. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 3, Reach/Lift/Stand up Fork Lift, Electric,4,500 lbs.

Vendor: Pape’ Material Handling

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 4,500 lbs. at 24” load center |X | |

|2. |Standard forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 210”, not to exceed 220” |X | |

|5. |Maximum load lifting speeds, fully variable: 60 fpm |X | |

|6. |Truck overall collapse height: not to exceed 95” |X | |

|7. |Maximum travel speed with full load: 6.5 mph |X | |

|8. |Side shift |X | |

|9. |Up and down function controls |X | |

|10. |Reach in – out minimum: 23” |X | |

|11. |Tilt: 3 degrees forward and 4 degrees backwards |X | |

|12. |Gross weight without battery: 5,850 |X | |

|13. |Top mounted steering handle |X | |

|14. |Overhead guard not to exceed 95” |X | |

|15. |Total body width not to exceed 41” |X | |

|16. |Base leg opening: no less than 28” ID and OD not to exceed 40” |X | |

|17. |Operator restraint system |X | |

|18. |Solid state controlled electrical system |X | |

|19. |Steering: hydrostatic |X | |

|20. |Brakes: mechanical disc or drum |X | |

|21. |Proportional plugging |X | |

|22. |Load stabilizing caster, soft poly, approximate size: 7” x 2.75” |X | |

|23. |Drive tire: rubber, approximate size: 13.5” x 5” |X | |

|24. |Load wheels: poly, approximate size: 5” x 4” |X | |

|25. |Battery power: 24 volt |X |36 VOLT |

|26. |Battery discharge indicator/meter |X | |

|27. |Hour meter |X | |

|28. |Top mounted steering handle with twist grip with speed control |X | |

|29 |Lift/lower button |X | |

|30. |On/off power switch |X | |

|31. |Horn |X | |

|32. |Lubrication fittings at pivot points |X | |

|33. |SB-175 connector |X | |

|34. |Owner’s manual |X | |

|35. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 4, Sit Down Fork Lift, 3-Wheel, Electric,3,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As Specified Or|Describe Fully If Not |

| | |Exceeds |As Specified |

|1. |Basic capacity: minimum of 3,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Lift height minimum: 185”, not to exceed 220” |X – 189” | |

|5. |Maximum load lifting speeds, fully variable: 65 fpm |X | |

|6. |Tilt: 5 degrees forward and 6 degrees backward |X | |

|7. |Side-shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 83.5” | |

|10. |Maximum travel speed with full load: 8 mph |X | |

|11. |Gross weight maximum without battery: 4,650 lbs |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Steering: hydrostatic |X | |

|14. |Proportional plugging |X | |

|15. |Operator restraint system with non-suspension seat |X | |

|16. |Truck body width: not to exceed 42” |X -41.5” | |

|17 |Drive Tire, rubber, approximate size: 18” x 7” x 12” |X | |

| |Steer Tires, (dual), rubber, approximate size: 15” x 5” x 11” | | |

|18. |Rear view mirror |X | |

|19 |Work lights |X | |

|20. |Flashing lights |X | |

|21. |Brakes: mechanical disk or drum |X | |

|22. |Battery power: 36 volt |X | |

|23. |Battery discharge indicator/meter |X | |

|24. |Hour meter |X | |

|25. |Solid state controlled electrical system |EXCEED – AC DRIVE, LIFT | |

| | |AND HYD. MOTORS | |

|26. |On/off power switch |X | |

|27. |Horn |X | |

|28. |Lubrication fittings at pivot points |X | |

|29. |SB-350 connector |X | |

|30. |Owner’s manual |X | |

|31. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 4, Sit Down Fork Lift, 3-Wheel, Electric,3,500 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As Specified Or|Describe Fully If Not |

| | |Exceeds |As Specified |

|1. |Basic capacity: minimum of 3,500 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Lift height minimum: 185”, not to exceed 220” |X – 189” | |

|5. |Maximum load lifting speeds, fully variable: 60 fpm |X | |

|6. |Tilt: 5 degrees forward and 6 degrees backward |X | |

|7. |Side-shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 83.5” | |

|10. |Maximum travel speed with full load: 9 mph |X | |

|11. |Gross weight maximum without battery: 5,000 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Steering: hydrostatic |X | |

|14. |Proportional plugging |X | |

|15. |Operator restraint system with non-suspension seat |X | |

|16. |Truck body width: not to exceed 42” |X -41.5” | |

|17 |Drive Tire, rubber, approximate size: 18” x 7” x 12” |X | |

| |Steer Tires, (dual), rubber, approximate size: 15” x 5” x 11” | | |

|18. |Rear view mirror |X | |

|19 |Work lights |X | |

|20. |Flashing lights |X | |

|21. |Brakes: mechanical disk or drum |X | |

|22. |Battery power: 36 volt |X | |

|23. |Battery discharge indicator/meter |X | |

|24. |Hour meter |X | |

|25. |Solid state controlled electrical system |EXCEED – AC DRIVE, LIFT | |

| | |AND HYD. MOTORS | |

|26. |On/off power switch |X | |

|27. |Horn |X | |

|28. |Lubrication fittings at pivot points |X | |

|29. |SB-350 connector |X | |

|30. |Owner’s manual |X | |

|31. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 4, Sit Down Fork Lift, 3-Wheel, Electric,4,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As Specified Or|Describe Fully If Not |

| | |Exceeds |As Specified |

|1. |Basic capacity: minimum of 4,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Lift height minimum: 185”, not to exceed 220” |X – 189” | |

|5. |Maximum load lifting speeds, fully variable: 58 fpm |X | |

|6. |Tilt: 5 degrees forward and 6 degrees backward |X | |

|7. |Side-shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 83.5” | |

|10. |Maximum travel speed with full load: 8.8 mph |X | |

|11. |Gross weight maximum without battery: 5,150 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Steering: hydrostatic |X | |

|14. |Proportional plugging |X | |

|15. |Operator restraint system with non-suspension seat |X | |

|16. |Truck body width: not to exceed 42” |X -41.5” | |

|17 |Drive Tire, rubber, approximate size: 18” x 7” x 12” |X | |

| |Steer Tires, (dual), rubber, approximate size: 15” x 5” x 11” | | |

|18. |Rear view mirror |X | |

|19 |Work lights |X | |

|20. |Flashing lights |X | |

|21. |Brakes: mechanical disk or drum |X | |

|22. |Battery power: 36 volt |X | |

|23. |Battery discharge indicator/meter |X | |

|24. |Hour meter |X | |

|25. |Solid state controlled electrical system |EXCEED – AC DRIVE, LIFT | |

| | |AND HYD. MOTORS | |

|26. |On/off power switch |X | |

|27. |Horn |X | |

|28. |Lubrication fittings at pivot points |X | |

|29. |SB-350 connector |X | |

|30. |Owner’s manual |X | |

|31. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 3,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 3,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 185”, not to exceed 220” |X – 189” | |

|5. |Maximum load lifting speeds, fully variable: 60 fpm |X | |

|6. |Tilt: 6 degrees forward and 5 degrees backward |X | |

|7. |Side shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 86.4” | |

|10. |Maximum travel speed with full load: 8.8 mph |X | |

|11. |Gross weight maximum without battery: 5,000 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Operator restraint system with non-suspension seat |X | |

|14. |Tires: |X | |

| |Drive Tire, rubber, approximate size: 18” x 6” x 12” | | |

| |Steer Tires, rubber, approximate size: 14” x 4” x 8” | | |

|15. |Steering: hydrostatic |X | |

|16. |Proportional plugging |X | |

|17. |Rear view mirror |X | |

|18. |Work lights |X | |

|19. |Flashing lights |X | |

|20. |Brakes: hydraulic |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |EXCEED – AC DRIVE | |

| | |MOTORS | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 3,500 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 3,500 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 185”, not to exceed 220” |X – 189” | |

|5. |Maximum load lifting speeds, fully variable: 60 fpm |X | |

|6. |Tilt: 6 degrees forward and 5 degrees backward |X | |

|7. |Side shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 86.4” | |

|10. |Maximum travel speed with full load: 8.6 mph |X | |

|11. |Gross weight maximum without battery: 5,250 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Operator restraint system with non-suspension seat |X | |

|14. |Tires: |X | |

| |Drive Tire, rubber, approximate size: 18” x 6” x 12” | | |

| |Steer Tires, rubber, approximate size: 14” x 4” x 8” | | |

|15. |Steering: hydrostatic |X | |

|16. |Proportional plugging |X | |

|17. |Rear view mirror |X | |

|18. |Work lights |X | |

|19. |Flashing lights |X | |

|20. |Brakes: hydraulic |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |EXCEED – AC DRIVE | |

| | |MOTORS | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 4,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: 4,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 185”, not to exceed 220” |X – 189” | |

|5. |Maximum load lifting speeds, fully variable: 62 fpm |X | |

|6. |Tilt: 6 degrees forward and 5 degrees backward |X | |

|7. |Side shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 88” | |

|10. |Maximum travel speed with full load: 10.4 mph |X | |

|11. |Gross weight maximum without battery: 6,150 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Operator restraint system with non-suspension seat |X | |

|14. |Tires: |X | |

| |Drive Tire, rubber, approximate size: 21” x 7” x 15” | | |

| |Steer Tires, rubber, approximate size: 16” x 5” x 10” | | |

|15. |Steering: hydrostatic |X | |

|16. |Proportional plugging |X | |

|17. |Rear view mirror |X | |

|18. |Work lights |X | |

|19. |Flashing lights |X | |

|20. |Brakes: hydraulic |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |EXCEED – AC DRIVE | |

| | |MOTORS | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 5,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 5,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 185”, not to exceed 220” |X – 189” | |

|5. |Maximum load lifting speeds, fully variable: 54 fpm |X | |

|6. |Tilt: 6 degrees forward and 5 degrees backward |X | |

|7. |Side shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 88” | |

|10. |Maximum travel speed with full load: 9.7 mph |X | |

|11. |Gross weight maximum without battery: 7,050 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Operator restraint system with non-suspension seat |X | |

|14. |Tires: |X | |

| |Drive Tire, rubber, approximate size: 21” x 7” x 15” | | |

| |Steer Tires, rubber, approximate size: 16” x 5” x 10” | | |

|15. |Steering: hydrostatic |X | |

|16. |Proportional plugging |X | |

|17. |Rear view mirror |X | |

|18. |Work lights |X | |

|19. |Flashing lights |X | |

|20. |Brakes: hydraulic |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |EXCEED – AC DRIVE | |

| | |MOTORS | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 6,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 6,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 185”, not to exceed 220” |X – 189” | |

|5. |Maximum load lifting speeds, fully variable: 46 fpm |X | |

|6. |Tilt: 6 degrees forward and 5 degrees backward |X | |

|7. |Side shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 88” | |

|10. |Maximum travel speed with full load: 9.1 mph |X | |

|11. |Gross weight maximum without battery: 7,650 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Operator restraint system with non-suspension seat |X | |

|14. |Tires: |X | |

| |Drive Tire, rubber, approximate size: 21” x 8” x 15” | | |

| |Steer Tires, rubber, approximate size: 16” x 6” x 10” | | |

|15. |Steering: hydrostatic |X | |

|16. |Proportional plugging |X | |

|17. |Rear view mirror |X | |

|18. |Work lights |X | |

|19. |Flashing lights |X | |

|20. |Brakes: hydraulic |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |EXCEED – AC DRIVE | |

| | |MOTORS | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 7,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 7,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 185”, not to exceed 220” |X – 189” | |

|5. |Maximum load lifting speeds, fully variable: 46 fpm |X | |

|6. |Tilt: 6 degrees forward and 5 degrees backward |X | |

|7. |Side shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 88” | |

|10. |Maximum travel speed with full load: 9.1 mph |X | |

|11. |Gross weight maximum without battery: 7,650 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Operator restraint system with non-suspension seat |X | |

|14. |Tires: |X | |

| |Drive Tire, rubber, approximate size: 21” x 9” x 15” | | |

| |Steer Tires, rubber, approximate size: 16” x 6” x 10” | | |

|15. |Steering: hydrostatic |X | |

|16. |Proportional plugging |X | |

|17. |Rear view mirror |X | |

|18. |Work lights |X | |

|19. |Flashing lights |X | |

|20. |Brakes: hydraulic |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |EXCEED – AC DRIVE | |

| | |MOTORS | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 8,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 8,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 42” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 185”, not to exceed 220” |X – 187” | |

|5. |Maximum load lifting speeds, fully variable: 49 fpm |X | |

|6. |Tilt: 6 degrees forward and 5 degrees backward |X | |

|7. |Side shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 90” | |

|10. |Maximum travel speed with full load: 8.1 mph |X | |

|11. |Gross weight maximum without battery: 10,450 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Operator restraint system with non-suspension seat |X | |

|14. |Tires: |X | |

| |Drive Tire, rubber, approximate size: 21” x 8” x 15” | | |

| |Steer Tires, rubber, approximate size: 16” x 6” x 10” | | |

|15. |Steering: hydrostatic |X | |

|16. |Proportional plugging |X | |

|17. |Rear view mirror |X | |

|18. |Work lights |X | |

|19. |Flashing lights |X | |

|20. |Brakes: hydraulic |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |EXCEED – AC DRIVE | |

| | |MOTORS | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 12,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of12,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 48” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 185”, not to exceed 220” |X – 187” | |

|5. |Maximum load lifting speeds, fully variable: 49 fpm |X | |

|6. |Tilt: 6 degrees forward and 5 degrees backward |X | |

|7. |Side shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 90” | |

|10. |Maximum travel speed with full load: 8.1 mph |X | |

|11. |Gross weight maximum without battery: 12,450 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Operator restraint system with non-suspension seat |X | |

|14. |Tires: |X | |

| |Drive Tire, rubber, approximate size: 28” x 10” x 22” | | |

| |Steer Tires, rubber, approximate size: 18” x 8” x 12-1/8” | | |

|15. |Steering: hydrostatic |X (EHPS) | |

|16. |Proportional plugging |X | |

|17. |Rear view mirror |X | |

|18. |Work lights |X | |

|19. |Flashing lights |X | |

|20. |Brakes: hydraulic |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |EXCEED – AC DRIVE | |

| | |MOTORS | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |36 Months or 6,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Sit Down Fork Lift, 4-Wheel, Pneumatic, Electric, 4,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 4,000 lbs. at 24” load center |X | |

|2. |Tapered forks: 48” x 4” x 1.4” |X | |

|3. |Adjustable fork width: 15” to 29” |X | |

|4. |Fork lift height minimum: 185”, not to exceed 220” |X – 187” | |

|5. |Maximum load lifting speeds, fully variable: 49 fpm |X | |

|6. |Tilt: 6 degrees forward and 5 degrees backward |X | |

|7. |Side shift |X | |

|8. |Up and down function controls |X | |

|9. |Truck overall collapsed height including mast height not to exceed 95” |X – 83.7” | |

|10. |Maximum travel speed with full load: 10.30 mph |X | |

|11. |Gross weight maximum without battery: 4,450 lbs. |X | |

|12. |Cage above operator & load backrest |X | |

|13. |Operator restraint system with non-suspension seat |X | |

|14. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 21” x 18” x 9-14” | | |

| |Steer Tires, rubber, approximate size: 18” x 7” x 8-14” | | |

|15. |Steering: hydrostatic |X (EHPS) | |

|16. |Proportional plugging |X | |

|17. |Rear view mirror |X | |

|18. |Work lights |X | |

|19. |Flashing lights |X | |

|20. |Brakes: hydraulic |X | |

|21. |Battery power: 48 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |EXCEED – AC DRIVE | |

| | |MOTORS | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |36 Months or 6,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 3,500 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 3,500 lbs. at 24” load center |X | |

|2. |Forks: 42”x 4” x 1.4” |X | |

|3. |Fork lift height minimum: 170” |X – 171” | |

|4. |Triple stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 130 fpm |X | |

|9. |Minimum travel speed: 11 mph |X | |

|10. |Power shift transmission, 2-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 6.5 - 10 – 10 PR | | |

| |Steer Tires, rubber, approximate size: 5.00 – 8 – 8 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an LPG fuel system and steel |EXCEED - 0.6 | |

| |tank meeting 2010 CARB standards |(G/BHP-HR) STANDARD | |

| | |IS 1.0 | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 4,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 4,000 lbs. at 24” load center |X | |

|2. |Forks: 42”x 4” x 1.4” |X | |

|3. |Fork lift height minimum: 170” |X – 171” | |

|4. |Triple stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 116 fpm |X | |

|9. |Minimum travel speed: 10 mph |X | |

|10. |Power shift transmission, 2-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 7.00 - 12 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 6.00 – 9 – 10 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an LPG fuel system and steel |EXCEED - 0.6 | |

| |tank meeting 2010 CARB standards |(G/BHP-HR) STANDARD | |

| | |IS 1.0 | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 5,000lbs.,

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 5,000 lbs. at 24” load center |X | |

|2. |Forks: 42”x 4” x 1.4” |X | |

|3. |Fork lift height minimum: 170” |X – 171” | |

|4. |Triple stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 116 fpm |X | |

|9. |Minimum travel speed: 10 mph |X | |

|10. |Power shift transmission, 2-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 7.00 - 12 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 6.00 – 9 – 10 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an LPG fuel system and steel |EXCEED - 0.6 | |

| |tank meeting 2010 CARB standards |(G/BHP-HR) STANDARD | |

| | |IS 1.0 | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 6,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 6,000 lbs. at 24” load center |X | |

|2. |Forks: 42”x 4” x 1.4” |X | |

|3. |Fork lift height minimum: 170” |X – 171” | |

|4. |Triple stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 98 fpm |X | |

|9. |Minimum travel speed: 11 mph |X | |

|10. |Power shift transmission, 2-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 28 x 9 - 15 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 6.50 – 10 – 10 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an LPG fuel system and steel |EXCEED - 0.6 | |

| |tank meeting 2010 CARB standards |(G/BHP-HR) STANDARD | |

| | |IS 1.0 | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 6,500 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 6,500 lbs. at 24” load center |X | |

|2. |Forks: 42”x 4” x 1.4” |X | |

|3. |Fork lift height minimum: 130” |X | |

|4. |2 - stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 95 fpm |X | |

|9. |Minimum travel speed: 11 mph |X | |

|10. |Automatic transmission, single-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 28 x 9 - 15 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 6.50 – 10 – 10 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an LPG fuel system and steel |EXCEED - 0.6 | |

| |tank meeting 2010 CARB standards |(G/BHP-HR) STANDARD | |

| | |IS 1.0 | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 8,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 8,000 lbs. at 24” load center |X | |

|2. |Forks: 42”x 4” x 1.4” |X | |

|3. |Fork lift height minimum: 170” |X – 171” | |

|4. |Triple stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 98 fpm |X | |

|9. |Minimum travel speed: 13 mph |X | |

|10. |Power shift transmission, 2-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 28 x 9 - 15 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 6.50 – 10 – 10 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an LPG fuel system and steel |X | |

| |tank meeting 2010 CARB standards | | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, LPG,10,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 10,000 lbs. at 24” load center |X | |

|2. |Forks: 42”x 4” x 1.4” |X | |

|3. |Fork lift height minimum: 170” |X – 171” | |

|4. |Triple stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 86 fpm |X | |

|9. |Minimum travel speed: 13 mph |X | |

|10. |Power shift transmission, 2-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 28 x 9 - 15 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 6.50 – 10 – 10 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an LPG fuel system and steel |X | |

| |tank meeting 2010 CARB standards | | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 11,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 11,000 lbs. at 24” load center |X | |

|2. |Forks: 48” x 6” x 2” |X | |

|3. |Fork lift height minimum: 170” |X – 171” | |

|4. |Triple stage mast assembly |X | |

|5. |Side shifter |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, Single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 86 fpm |X | |

|9. |Minimum travel speed: 13 mph |X | |

|10. |Power shift transmission, 2-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 28 x 9 - 15 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 6.50 – 10 – 10 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an LPG fuel system and steel |X | |

| |tank meeting 2014 CARB standards | | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |36 Months or 6,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

| | | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, DIESEL, 4,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 4,000 lbs. at 24” load center |X | |

|2. |Forks: 7” x 2” x 48” Class IV Hook Mount Forks | |48” x 5” x 1.5” Class |

| | | |II Forks |

|3. |Fork lift height minimum: 170” |X | |

|4. |Triple stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 86 fpm |X | |

|9. |Maximum travel speed: 11 mph |X | |

|10. |Automatic Transmission, 1-speed forward and 1-speed reverse |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 7.00 – 12 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 6.00 – 9 – 10 PR | | |

|18. |Internal Combustion Engine, Toyota, 152 cu in. 4-cylinder 44 hp, OHV Diesel Engine (1 DZ-II). Meets CARB |X | |

| |In-Use Off-Road Diesel Vehicle Regulations. | | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, Diesel, 8,000 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 8,000 lbs. at 24” load center |X | |

|2. |Forks: 42”x 4” x 1.4” |X | |

|3. |Fork lift height minimum: 170” |X – 171” | |

|4. |Triple stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 98 fpm |X | |

|9. |Minimum travel speed: 13 mph |X | |

|10. |Power shift transmission, 2-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 28 x 9 - 15 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 6.50 – 10 – 10 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an LPG fuel system and steel |X | |

| |tank meeting 2010 CARB standards | | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |36 Months or 6,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 6, Pneumatic Tire Sit Down Fork Lift, DIESEL, 15,500 lbs.

Vendor: Toyota Lift Northwest

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 15,500 lbs. at 24” load center |X | |

|2. |Forks: 42”x 4” x 1.4” |X | |

|3. |Fork lift height minimum: 170” |X | |

|4. |Triple stage mast assembly |X | |

|5. |Side shift |X | |

|6. |Tilt: 6 degrees forward and 6 degrees backward |X | |

|7. |3-way valve, single-function |X | |

|8. |Maximum load lifting speeds, fully variable: 116 fpm |X | |

|9. |Minimum travel speed: 10 mph |X | |

|10. |Power shift transmission, 2-speed |X | |

|11. |Steering: Hydrostatic |X | |

|12. |Hydraulic disk or drum brakes |X | |

|13. |Lever or foot operated parking brake |X | |

|14. |Factory installed work lights front and rear |X | |

|15. |Operator restraint system with adjustable seat |X | |

|16 |Rear view mirror |X | |

|17. |Tires: pneumatic |X | |

| |Drive Tire, rubber, approximate size: 8.25 - 15 – 12 PR | | |

| |Steer Tires, rubber, approximate size: 8.25 – 15 – 12 PR | | |

|18. |Internal Combustion Engine: as appropriate for each unit and is equipped with an Diesel fuel system meeting |X | |

| |2010 CARB standards | | |

|19. |Lubrication fittings at pivot points |X | |

|20. |Horn |X | |

|21. |Steering wheel spinner-knob |X | |

|22. |Owner’s manual |X | |

|23. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 7, Walk Behind Adjustable Stacker, Electric, 2,000 lbs.

Vendor: Pape’ Material Handling

| |Description |Check If As Specified |Describe Fully If Not |

| | |Or Exceeds |As Specified |

|1. |Basic capacity: minimum of 2,000 lbs. at 24” load center |X |2500 LBS |

|2. |Fork length: 42” x 4” x 1.5” |X | |

|3. |Adjustable fork width: 10” – 31” |X | |

|4. |Fork lift height minimum: 128” |X | |

|5. |Base legs opening I.D. 32” – 51” |X | |

|6. |Maximum lift speed full load: 24 fpm |X | |

|7. |Gross weight maximum without battery: 1,725 lbs. |X | |

|8. |Maximum travel speed loaded: 3.2 mph |X | |

|9. |Drive wheels, rubber, approximate size: 10” x 5” |X | |

|10. |Load wheels, poly, two (2), approximate size: 4 x 3” |X | |

|11. |Brake: electric disc |X | |

|12. |Solid state controlled electrical system |X | |

|13. |Proportional plugging |X | |

|14. |Built-in 110 volt battery charger |X | |

|15. |Battery: 24 volt |X | |

|16. |Battery discharge indicator/meter |X | |

|17. |Hour meter |X | |

|18. |Multi-function controls with twist grip speed control, directional reversing and dead man brake. |X | |

|19. |Lift/lower button |X | |

|20. |On/off power switch |X | |

|21. |Horn |X | |

|22. |Lubrication fittings at pivot points |X | |

|23. |SB-175 connector |X | |

|24. |Owner’s manual |X | |

|25. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 7, Walk Behind Adjustable Stacker, Electric, 2,500 lbs.

Vendor: Pape’ Material Handling

| |Description |Check If As Specified |Describe Fully If Not |

| | |Or Exceeds |As Specified |

|1. |Basic capacity: minimum of 2,500 lbs. at 24” load center |X | |

|2. |Fork length: 42” x 4” x 1.5” |X | |

|3. |Adjustable fork width: 10” – 31” |X | |

|4. |Fork lift height minimum: 128” |X | |

|5. |Base legs opening I.D. 32” – 51” |X | |

|6. |Maximum lift speed full load: 21 fpm |X | |

|7. |Gross weight maximum without battery: 1,725 lbs. |X | |

|8. |Maximum travel speed loaded: 3.2 mph |X | |

|9. |Drive wheels, rubber, approximate size: 10” x 5” |X | |

|10. |Load wheels, poly, two (2), approximate size: 4 x 3” |X | |

|11. |Brake: electric disc |X | |

|12. |Solid state controlled electrical system |X | |

|13. |Proportional plugging |X | |

|14. |Built-in 110 volt battery charger |X | |

|15. |Battery power: 24 volt |X | |

|16. |Battery discharge indicator/meter |X | |

|17. |Hour meter |X | |

|18. |Multi-function controls with twist grip speed control, directional reversing and dead man brake. |X | |

|19. |Lift/lower button |X | |

|20. |On/off power switch |X | |

|21. |Horn |X | |

|22. |Lubrication fittings at pivot points |X | |

|23. |SB-175 connector |X | |

|24. |Owner’s manual |X | |

|25. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 8, Stand up Fork Lift, Electric, 3,500 lbs.

Vendor: Pape’ Material Handling

| |Description |Check If As Specified |Describe Fully If Not |

| | |Or Exceeds |As Specified |

|1. |Basic capacity: minimum of 3,500 lbs. at 24” load center |X | |

|2. |Standard forks: 42” x 4” x 1.5” |X | |

|3. |Adjustable fork width: 8” to 35” |X | |

|4. |Fork lift height minimum: 185” |X | |

|5. |Maximum load lifting speeds, fully variable: 69 fpm |X | |

|6. |Truck overall collapse height: not to exceed 95” |X | |

|7. |Gross weight maximum without battery: 7,150 lbs. |X | |

|8. |Maximum travel speed with full load: 7 mph |X | |

|9. |Side shift |X | |

|10. |Up and down function controls |X | |

|11. |Tilt: 3 degrees forward and 4 degrees backwards |X | |

|12. |Top mounted steering handle with twist grip with speed control |X | |

|13. |Overhead guard not to exceed 95” |X | |

|14. |Operator restraint system |X | |

|15. |Solid state controlled electrical system |X | |

|16. |Steering: hydrostatic |X | |

|17. |Proportional plugging |X | |

|18. |Drive tire: solid rubber, approximate size: 16” x 6” x 11” |X | |

|19. |Load wheels: poly, approximate size: 10” x 7” |X | |

|20. |Brakes: electric disc |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |X | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 8, Stand up Fork Lift, Electric, 4,000 lbs.

Vendor: Pape’ Material Handling

| |Description |Check If As |Describe Fully If Not |

| | |Specified Or Exceeds|As Specified |

|1. |Basic capacity: minimum of 4,000 lbs. at 24” load center |X | |

|2. |Standard forks: 42” x 4” x 1.5” |X | |

|3. |Adjustable fork width: 8” to 35” |X | |

|4. |Fork lift height minimum: 185” |X | |

|5. |Maximum load lifting speeds, fully variable: 69 fpm |X | |

|6. |Truck overall collapse height: not to exceed 95” |X | |

|7. |Gross weight maximum without battery: 7,150 lbs. |X | |

|8. |Maximum travel speed with full load: 7 mph |X | |

|9. |Side shift |X | |

|10. |Up and down function controls |X | |

|11. |Tilt: 3 degrees forward and 4 degrees backwards |X | |

|12. |Top mounted steering handle with twist grip with speed control |X | |

|13. |Overhead guard not to exceed 95” |X | |

|14. |Operator restraint system |X | |

|15. |Solid state controlled electrical system |X | |

|16. |Steering: hydrostatic |X | |

|17. |Proportional plugging |X | |

|18. |Drive tire: solid rubber, approximate size: 16” x 6” x 11” |X | |

|19. |Load wheels: poly, approximate size: 10” x 7” |X | |

|20. |Brakes: electric disc |X | |

|21. |Battery power: 36 volt |X | |

|22. |Battery discharge indicator/meter |X | |

|23. |Hour meter |X | |

|24. |Solid state controlled electrical system |X | |

|25. |On/off power switch |X | |

|26. |Horn |X | |

|27. |Lubrication fittings at pivot points |X | |

|28. |SB-350 connector |X | |

|29. |Owner’s manual |X | |

|30. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

Minimum specifications called for:

Category 9, Stand up Fork Lift with Counter Balance, Electric, 5,000 lbs.

Vendor: Raymond Handling Concepts

| |Description |Check If As Specified |Describe Fully If Not |

| | |Or Exceeds |As Specified |

|1. |Basic capacity: minimum of 5,000 lbs. at 24” load center |X | |

|2. |Standard forks: 42” x 4” x 1.75” |X | |

|3. |Adjustable fork width: 8” to 35” |X | |

|4. |Fork lift height minimum: 188” |X | |

|5. |Maximum load lifting speeds, fully variable: 65 fpm |X | |

|6. |Truck overall collapse height: not to exceed 95” |X | |

|7. |Gross weight maximum without battery: 7,450 lbs. |X | |

|8. |Maximum travel speed with full load: 7 mph |X | |

|9. |Side shift |X | |

|10. |Up and down function controls |X | |

|11. |Tilt: 3 degrees forward and 4 degrees backwards |X | |

|12. |Top mounted steering handle with twist grip with speed control |X | |

|13. |Overhead guard not to exceed 95” |X | |

|14. |Solid state controlled electrical system |X | |

|15. |Steering: hydrostatic |X | |

|16. |Proportional plugging |X | |

|17. |Drive tire: solid rubber, approximate size: 16.25” x 7” x 11” |X | |

|18. |Brakes: electric disc |X | |

|19. |Battery power: 36 volt |X | |

|20. |Battery discharge indicator/meter |X | |

|21. |Hour meter |X | |

|22. |Solid state controlled electrical system |X | |

|23. |On/off power switch |X | |

|24. |Horn |X | |

|25. |Lubrication fittings at pivot points |X | |

|26. |SB-350 connector |X | |

|27. |Owner’s manual |X | |

|28. |Basic warranty: |X | |

| |12 Months or 2,000 hours: Basic (major components) | | |

| |24 Months or 4,000 hours: Power train | | |

| |(See price list for extended warranty and maintenance options) | | |

Return to Specifications for Categories Page

APPENDIX D BIDDER PROFILE

Raymond Handling Concepts

North West Handling Systems

Pape’ Material Handling

Toyota Lift Northwest

Contractor: North West Handling Systems

Awarded: Category 1

|Federal Identification Number: |91-0869801 |Supplier #: W6651 |

|WA State Department of Revenue Registration Number:|C600-051-641 | |

|Company Website: | | |

|Shipping Location: |FOB Destination |Prompt Payment Discount: |0% 30 days. |

|Purchasing Cards accepted: |Yes |Volume Discount: |N/A % |

Standard Lead Time after receipt of order (ARO): 120 calendar days.

Primary Contact-Contract Administration Alternate Contact-Contract Administration

|Name: |Tom Tate |Name: |Kurt Fluegge |

|Telephone: |425-255-0500 |Telephone: |425-255-0500 |

|Toll Free No. |800-426-3888 |Toll Free No. |800-426-3888 |

|Mobile Phone |206-715-6633 |Mobile Phone |206-817-0872 |

|Territory: |Pierce & Thurston Counties. |Territory: |Washington |

|Fax: |425-228-6946 |Fax: |425-228-6946 |

|Email: |tomt@ |Email: |kurtf@ |

Warranty and Repair Contact

|Name: |Joe Ysebaert |

|Telephone: |425-255-0500 |

|Fax: |425-228-6946 |

|Email: |joey@ |

Addresses:

|Orders to be sent to: | |Billing will be from: | |Payment to be sent to: |

|North West Handling Systems, Inc. | |North West Handling Systems, Inc. | |North West Handling Systems, Inc. |

|1100 SW 7th. St. | |1100 SW 7th. St. | |1100 SW 7th. St. |

|Renton, WA 98057 | |Renton, WA 98057 | |Renton, WA 98057 |

|Email: tomt@ | |Email: tomt@ | |Email: tomt@ |

Contractor: Pape’ Material Handling

Awarded: Category 2, 3 7 & 8

|Federal Identification Number: |93-1035514 |Supplier #: W17609 |

|WA State Department of Revenue Registration Number: |601264586 | |

|Company Website: | | |

Shipping Location: FOB Destination

|Shipping Location: |FOB Destination |Prompt Payment Discount: |0% 30 days. |

|Purchasing Cards accepted: |Yes |Volume Discount: |N/A % |

Standard Lead Time after receipt of order (ARO): 120 calendar days.

Primary Contact-Contract Administration Alternate Contact-Contract Administration

|Name: |Greg Bogart |Name: |Sara George |

|Telephone: |509-536-7312 |Telephone: |206-760-4334 |

|Toll Free No. |1-888-813-2580 |Toll Free No. |1-888-813-2580 |

|Mobile Phone |509-994-7926 |Mobile Phone |206-730-1819 |

|Territory: |Washington & Oregon |Territory: |Washington & Oregon |

|Fax: |509-536-7333 |Fax: |206-508-3890 |

|Email: |gbogart@ |Email: |sgeorge@ |

Warranty and Repair Contact

|Name: |Kate Anderson |

|Telephone: |253-926-5922 |

|Fax: |253-926-5909 |

|Email: |kanderson@ |

Addresses:

|Orders to be sent to: | |Billing will be from: | |Payment to be sent to: |

|Pape’ Material Handling | |Pape’ Material Handling | |Pape’ Material Handling |

|5518 East Broadway | |PO Box 5077 | |PO Box 5077 |

|Spokane, WA 99212 | |Portland, OR 97208 | |Portland, OR 97208 |

|Attn: Greg Bogart | | | |Attn: Cathy Snow |

|Email: gbogart@ | |Email: gbogart@ | |Email: csnow@ |

Contractor: Raymond Handling Concepts

Awarded: Category 9

|Federal Identification Number: |94-3049535 |Supplier #: W6181 |

|WA State Department of Revenue Registration |601785727 | |

|Number: | | |

|Company Website: | | |

|Shipping Location: |FOB Destination |Prompt Payment Discount: |0% 30 days. |

|Purchasing Cards accepted: |Yes |Volume Discount: |N/A % |

Standard Lead Time after receipt of order (ARO): 60 - 100 calendar days.

Primary Contact-Contract Administration Alternate Contact-Contract Administration

|Name: |Terry Hornbuckle |Name: |Scott Thurston |

|Telephone: |253-333-2100 |Telephone: |253-333-2100 |

|Toll Free No. |1-888-820-8811 |Toll Free No. |1-888-820-8811 |

|Mobile Phone |206-730-2989 |Mobile Phone | |

|Territory: |Washington |Territory: |Washington |

|Fax: |253.333.5051 |Fax: |253.333.5051 |

|Email: |terry.hornbuckle@ |Email: |sthurston@ |

Warranty and Repair Contact

|Name: |Dave Blau |

|Telephone: |253.333.2100 |

|Fax: |253.333.5051 |

|Email: |Daveb@ |

Addresses:

|Orders to be sent to: | |Billing will be from: | |Payment to be sent to: |

|Raymond Handling Concepts | |Raymond Handling Concepts | |Raymond Handling Concepts |

|3500 West Valley Hwy N | |41400 Boyce Rd. | |41400 Boyce Rd. |

|Auburn, WA 98001 | |Fremont, CA 94538 | |Fremont, CA 94538 |

|sthurston@ | |sthurston@ | |sthurston@ |

Contractor: Toyota Lift Northwest

Awarded: Category 4, 5 & 6

|Federal Identification Number: |75-3266402 |Supplier #: W24922 |

|WA State Department of Revenue Registration |602-859-598 | |

|Number: | | |

|Company Website: |toyotaliftnorthwest. | |

Shipping Location: FOB Destination

|Shipping Location: |FOB Destination |Prompt Payment Discount: |.5%, 30 days. |

|Purchasing Cards accepted: |No |Volume Discount: |N/A % |

Standard Lead Time after receipt of order (ARO): 120 calendar days.

Primary Contact-Contract Administration Alternate Contact-Contract Administration

|Name: |Bryan Lovely |Name: | |

|Telephone: |253-872-7114 |Telephone: | |

|Toll Free No. |800-232-2228 |Toll Free No. | |

|Mobile Phone |253-310-2392 |Mobile Phone | |

|Territory: |State of Washington |Territory: | |

|Fax: |253-872-9687 |Fax: | |

|Email: |blovely@toyotaliftnorthwest. |Email: | |

Warranty and Repair Contact

|Name: |Kwang Yu |

|Telephone: |253-872-7114 |

|Fax: |253-872-9687 |

|Email: |kyu@toyotaliftnorthwest. |

Addresses:

|Orders to be sent to: | |Billing will be from: | |Payment to be sent to: |

|Toyota Lift Northwest. | |Toyota Lift Northwest. | |Toyota Lift Northwest. |

|19305 – 72nd Ave S | |19305 – 72nd Ave S | |12001 SE Jennifer Street |

|Kent, WA 98032 | |Kent, WA 98032 | |Clackamas, OR 97015 |

|Email: blovely@toyotaliftnorthwest. | |Email: blovely@toyotaliftnorthwest. | |Email: kricci@toyotaliftnorthwest. |

APPENDIX E PRICE SHEET

|Category 1, Walk Behind Pallet Jack, Electric, 4,500 lbs. |

Vendor: North West Handling Systems, Inc.

|Mfg: CROWN |Model: WP2300 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$ INCLUDED |$3,874 |$3,874 |

|Date of manufacturer’s price list: 6/12/09 |

|Discount % off of list price for options |% 25 |

|Discount % off of list price for attachments |% 20 |

|Discount % off of list price for parts |% 10 |

|Repair Manuals |$ N/C |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$ 58 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program Available | Yes X No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$ 86 |

The Service interval will be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$ 338.00 |

|48 Month |8,000 |With Maintenance Program |$ 450.00 |

|60 Month |10,000 |With Maintenance Program |$ 562.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$ N/A |

|48 Month |8,000 |Without Maintenance Program |$ N/A |

|60 Month |10,000 |Without Maintenance Program |$ N/A |

Return to Prices for Categories Page

|Category 1, Walk Behind Pallet Jack, Electric, 6,000 lbs. |

Vendor: North West Handling Systems, Inc.

|Mfg:CROWN |Model:PW3500 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$ INCLUDED |$ 5,003 |$ 5,003 |

|Date of manufacturer’s price list: 7/10/09 |

|Discount % off of list price for options |% 25 |

|Discount % off of list price for attachments |% 20 |

|Discount % off of list price for parts |% 10 |

|Repair Manuals |$ N/C |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$ 58 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes X No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$ 86 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$ 375.00 |

|48 Month |8,000 |With Maintenance Program |$ 499.00 |

|60 Month |10,000 |With Maintenance Program |$ 623.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$ N/A |

|48 Month |8,000 |Without Maintenance Program |$ N/A |

|60 Month |10,000 |Without Maintenance Program |$ N/A |

Return to Prices for Categories Page

|Category 2, Riding Pallet Jack, End Control, Electric, 6,000 lbs. |

Vendor: Pape’ Material Handling

|Mfg: Hyster |Model: B60ZAC |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$0.00 No charge |$5,783.40 |$5,783.40 |

|Date of manufacturer’s price list: 6-1-2009 |

|Discount % off of list price for options |37% |

|Discount % off of list price for attachments |15% |

|Discount % off of list price for parts |15% |

|Repair Manuals |$300.00 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$50.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$75.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$350.00 |

|48 Month |8,000 |With Maintenance Program |$450.00 |

|60 Month |10,000 |With Maintenance Program |$550.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$350.00 |

|48 Month |8,000 |Without Maintenance Program |$450.00 |

|60 Month |10,000 |Without Maintenance Program |$550.00 |

Return to Prices for Categories Page

|Category 2, Riding Pallet Jack, End Control, Electric, 6,000 lbs., 8,000 lbs. |

Vendor: Pape’ Material Handling

|Mfg: Hyster |Model: B80ZAC |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$0.00 |$6,104.70 |$6,104.70 |

|Date of manufacturer’s price list: 6-1-2009 |

|Discount % off of list price for options |39% |

|Discount % off of list price for attachments |15% |

|Discount % off of list price for parts |15% |

|Repair Manuals |$300.00 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$50.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$75.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$350.00 |

|48 Month |8,000 |With Maintenance Program |$450.00 |

|60 Month |10,000 |With Maintenance Program |$550.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$350.00 |

|48 Month |8,000 |Without Maintenance Program |$450.00 |

|60 Month |10,000 |Without Maintenance Program |$550.00 |

Return to Prices for Categories Page

|Category 3, Reach/Lift/Stand up Fork Lift, Electric, 3,000 lbs. |

Vendor: Pape’ Material Handling

|Mfg: Hyster |Model: N35ZRS |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$0.00 No charge |$20,367.77 |$20,367.77 |

|Date of manufacturer’s price list: 9-1-2009 |

|Discount % off of list price for options |37% |

|Discount % off of list price for attachments |15% |

|Discount % off of list price for parts |15% |

|Repair Manuals |$300.00 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$65.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$75.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$555.00 |

|48 Month |8,000 |With Maintenance Program |$815.00 |

|60 Month |10,000 |With Maintenance Program |$1115.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$555.00 |

|48 Month |8,000 |Without Maintenance Program |$815.00 |

|60 Month |10,000 |Without Maintenance Program |$1115.00 |

Return to Prices for Categories Page

|Category 3, Reach/Lift/Stand up Fork Lift, Electric, 3,500 lbs. |

Vendor: Pape’ Material Handling

|Mfg: Hyster |Model: N35ZRS2 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$0.00 No charge |$23,372.00 |$23,372.00 |

|Date of manufacturer’s price list: 9-1-2009 |

|Discount % off of list price for options |37% |

|Discount % off of list price for attachments |15% |

|Discount % off of list price for parts |15% |

|Repair Manuals |$300.00 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$65.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$75.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$555.00 |

|48 Month |8,000 |With Maintenance Program |$815.00 |

|60 Month |10,000 |With Maintenance Program |$1115.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$555.00 |

|48 Month |8,000 |Without Maintenance Program |$815.00 |

|60 Month |10,000 |Without Maintenance Program |$1115.00 |

Return to Prices for Categories Page

[pic]

|Category 3, Reach/Lift/Stand up Fork Lift, Electric, 4,500 lbs. |

Vendor: Pape’ Material Handling

|Mfg: Hyster |Model: N45ZR |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$0.00 No Charge |$22,954.23 |$22,954.23 |

|Date of manufacturer’s price list: 9-1-2009 |

|Discount % off of list price for options |37% |

|Discount % off of list price for attachments |15% |

|Discount % off of list price for parts |15% |

|Repair Manuals |$300.00 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$65.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$75.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$555.00 |

|48 Month |8,000 |With Maintenance Program |$815.00 |

|60 Month |10,000 |With Maintenance Program |$1115.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$555.00 |

|48 Month |8,000 |Without Maintenance Program |$815.00 |

|60 Month |10,000 |Without Maintenance Program |$1115.00 |

Return to Prices for Categories Page

|Category 4, Sit Down Fork Lift, 3-Wheel, Electric, 3,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 7FBEU15 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$17,429.54 |$17,729.54 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$462 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 4, Sit Down Fork Lift, 3-Wheel, Electric, 3,500 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 8FBE18U |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$18,378.46 |$18,678.46 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

[pic]

|Category 4, Sit Down Fork Lift, 3-Wheel, Electric, 4,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 7FBEU20 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$18,685.87 |$18,985.87 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

[pic]

|Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 3,000 lbs. |

|Vendor: Toyota Lift Northwest |

|Mfg: Toyota |Model: 7FBCU15 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$16,808.50 |$17,108.50 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 3,500 lbs. |

|Vendor: Toyota Lift Northwest | |

|Mfg: Toyota |Model: 7FBCU18 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$18,801.15 |$19,101.15 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 4,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 8FBCU20 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$19,070.12 |$19,370.12 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 5,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 8FBCU25 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$19,942.94 |$20,242.94 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 6, 000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 8FBCU30 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$22,253.96 |$22,553.96 |

|Date of manufacturer’s price list: 11/15/2011 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 7,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 8FBCU32-Hi Capacity |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$28,707.61 |$29,007.61 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

[pic]

|Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 8,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 7FBCU35 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$37,415.65 |$37,715.65 |

|Date of manufacturer’s price list: 11/15/2011 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 5, Sit Down Fork Lift, 4-Wheel, Electric, 12,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 7FBCU55 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$44,878.00 |$45,178.00 |

|Date of manufacturer’s price list: 4/25/2016 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |Carriage to Counterweight |$900.00 |

|48 Month |8,000 |Carriage to Counterweight |$1000.00 |

|60 Month |10,000 |Carriage to Counterweight |$1300.00 |

|Term |Hours |Description |Price |

| | | | |

|48 Month |8,000 |Powertrain |$800.00 |

|60 Month |10,000 |Powertrain |$900.00 |

Return to Prices for Categories Page

[pic]

|Category 6, Sit Down Fork Lift, 4-Wheel, Pneumatic Electric, 4,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: Toyota |Model: 7FBH20 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$26,950.00 |$27,250.00 |

|Date of manufacturer’s price list: 7/14/2016 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$121.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |Carriage to Counterweight |$900.00 |

|48 Month |8,000 |Carriage to Counterweight |$1000.00 |

|60 Month |10,000 |Carriage to Counterweight |$1300.00 |

|Term |Hours |Description |Price |

| | | | |

|48 Month |8,000 |Powertrain |$800.00 |

|60 Month |10,000 |Powertrain |$900.00 |

Return to Prices for Categories Page

[pic]

|Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 3,500 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FGU18 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$20,118.60 |$20,418.60 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

[pic]

|Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 4,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FGU20 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$21,046.30 |$21,346.30 |

|Date of manufacturer’s price list: 11/15/2011 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 5,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FGU25 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$22,341.79 |$22,641.79 |

|Date of manufacturer’s price list: 11/15/2011 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 6,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FGU30 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$24,383.84 |$24,683.84 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 6,500 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FGU32 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300 |$25,763.84 |$26,063.84 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 8,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FG35U |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$34,089.08 |$34,389.08 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

[pic]

|Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 10,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FG45U |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$38,200.63 |$38,500.63 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

[pic]

|Category 6, Pneumatic Tire Sit Down Fork Lift, LPG, 11,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FG50U |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$47,045.00 |$47,345.00 |

|Date of manufacturer’s price list: 1/1/2015 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

[pic]

|Category 6, Pneumatic Tire Sit Down Fork Lift, DIESEL, 4,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FDU20, Tier-4 Final |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300 |$26,100.00 |$26,400.00 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes X No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

[pic]

|Category 6, Pneumatic Tire Sit Down Fork Lift, Diesel, 8,000 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 8FD35U |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$300.00 |$39,675.00 |$39,975.00 |

|Date of manufacturer’s price list: 1/1/2015 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450 |

|48 Month |8,000 |With Maintenance Program |$695 |

|60 Month |10,000 |With Maintenance Program |$945 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600 |

|48 Month |8,000 |Without Maintenance Program |$975 |

|60 Month |10,000 |Without Maintenance Program |$1,325 |

Return to Prices for Categories Page

|Category 6, Pneumatic Tire Sit Down Fork Lift, DIESEL, 15,500 lbs. |

Vendor: Toyota Lift Northwest

|Mfg: TOYOTA |Model: 7FDU70 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$500.00 |$52,411.56 |$52,711.56 |

|Date of manufacturer’s price list: 1/1/2013 |

|Discount % off of list price for options |0% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |10% |

|Repair Manuals |$125.00 (parts and service) |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$54.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$84.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$450.00 |

|48 Month |8,000 |With Maintenance Program |$695.00 |

|60 Month |10,000 |With Maintenance Program |$945.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$600.00 |

|48 Month |8,000 |Without Maintenance Program |$975.00 |

|60 Month |10,000 |Without Maintenance Program |$1,325.00 |

Return to Prices for Categories Page

|Category 7, Walk Behind Fork Lift, 2,000 lbs. |

Vendor: Pape’ Material Handling

|Mfg: Hyster |Model: W25ZA2 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$0.00 No charge |$8,373.07 |$8,373.07 |

|Date of manufacturer’s price list: 6-1-2009 |

|Discount % off of list price for options |38% |

|Discount % off of list price for attachments |15% |

|Discount % off of list price for parts |15% |

|Repair Manuals |$300.00 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$50.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$75.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$320.00 |

|48 Month |8,000 |With Maintenance Program |$440.00 |

|60 Month |10,000 |With Maintenance Program |$500.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$320.00 |

|48 Month |8,000 |Without Maintenance Program |$440.00 |

|60 Month |10,000 |Without Maintenance Program |$500.00 |

Return to Prices for Categories Page

|Category 7, Walk Behind Fork Lift, 2,500 lbs. |

Vendor: Pape’ Material Handling

|Mfg: Hyster |Model: W25ZA2 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$0.00 No Charge |$8,373.07 |$8,373.07 |

|Date of manufacturer’s price list: 6-1-2009 |

|Discount % off of list price for options |38% |

|Discount % off of list price for attachments |15% |

|Discount % off of list price for parts |15% |

|Repair Manuals |$300.00 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$50.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$75.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$320.00 |

|48 Month |8,000 |With Maintenance Program |$440.00 |

|60 Month |10,000 |With Maintenance Program |$500.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$320.00 |

|48 Month |8,000 |Without Maintenance Program |$440.00 |

|60 Month |10,000 |Without Maintenance Program |$500.00 |

Return to Prices for Categories Page

|Category 8, Stand Up Fork Lift, Electric, 3,500 lbs. |

Vendor: Pape’ Material Handling

|Mfg: Hyster |Model: E35HSD |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$0.00 No Charge |$20,580.88 |$20,580.88 |

|Date of manufacturer’s price list: 3-27-2009 |

|Discount % off of list price for options |40.75% |

|Discount % off of list price for attachments |15% |

|Discount % off of list price for parts |15% |

|Repair Manuals |$300.00 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$65.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$75.00 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$530.00 |

|48 Month |8,000 |With Maintenance Program |$705.00 |

|60 Month |10,000 |With Maintenance Program |$880.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$530.00 |

|48 Month |8,000 |Without Maintenance Program |$705.00 |

|60 Month |10,000 |Without Maintenance Program |$880.00 |

Return to Prices for Categories Page

|Category 8, Stand Up Fork Lift, 4,000 lbs. |

Vendor: Pape’ Material Handling

|Mfg: Hyster |Model: E40HSD2 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$0.00 No Charge |$22,991.65 |$22,991.65 |

|Date of manufacturer’s price list: 6-29-10 |

|Discount % off of list price for options |40.75% |

|Discount % off of list price for attachments |15% |

|Discount % off of list price for parts |15% |

|Repair Manuals |$300 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$65.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$75.00 |

The Service interval is to be determined by the customer and the contractor.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$530.00 |

|48 Month |8,000 |With Maintenance Program |$705.00 |

|60 Month |10,000 |With Maintenance Program |$880.00 |

|Term |Hours |Description |Price |

|36 Month |6,000 |Without Maintenance Program |$530.00 |

|48 Month |8,000 |Without Maintenance Program |$705.00 |

|60 Month |10,000 |Without Maintenance Program |$880.00 |

Return to Prices for Categories Page

|Category 9, Stand Up Fork Lift, Counter Balanced, Electric, 5,000 lbs. |

Vendor: Raymond Handling Concepts

|Mfg: Raymond |Model: 4250 |

|Set-Up, Testing Ready For Operation (STRO) |Equipment Cost FOB Destination Statewide (ECFS)|Total: |

|$376.00 |$1,350.00 |$28,151.00 |

|Date of manufacturer’s price list: July 13, 2010 |

|Discount % off of list price for options |36% |

|Discount % off of list price for attachments |20% |

|Discount % off of list price for parts |0% |

|Repair Manuals |$175.00 |

Maintenance Programs

|Description |Rate per Occurrence |

|Preventative Maintenance Program (Excluding Parts) |$70.00 |

|Description |Flat Rate billed Monthly |

|Full Maintenance Program | Yes No |

|Description |Hourly Rate |

|Time and materials repair, unscheduled (Excluding Parts) |$101.80 |

The Service interval is to be determined by the customer and the contractor.

Note: Batteries and chargers are options. Consult with the Sales Representative for your specific application.

Extended Warranty Options

|Term |Hours |Description |Price |

|36 Month |6,000 |With Maintenance Program |$193.00 |

|48 Month |8,000 |With Maintenance Program |$250.00 |

|60 Month |10,000 |With Maintenance Program |$275.00 |

Return to Prices for Categories Page

[pic]

APPENDIX F MINIMUM PREVENTATIVE MAINTENANCE, ELECTRIC POWERED EQUIPMENT

Visual Inspections

|Check for oil leaks |Check fabreeks pads |Inspect lift cylinder |Check tires |

|Inspect sheet metal |Inspect upright latch |Inspect packing lands |Check all switches |

|Check overhead guard |Inspect forks |Inspect chain retainers |Check battery connector |

|Inspect lift chains |Inspect rail pattern |Inspect load backrest |Inspect control linkage |

Operational Tests

|Test service brake |Test horn |Test speed control |Battery test load |

|Test parking brake |Check hour meter |Test directional control |Evaluate upright drift |

|Operate seat adjuster |Test brake limit switch |Operate steering |Check battery cables |

|Test battery indicator |Test plugging control |Test for upright racking |Check truck cables |

Mechanical Inspections

|Check master cylinder level |Inspect tilt mounting |Inspect sump breather |Check electrical panel |

|Check master cylinder linkage |Check trunions |Check hydraulic oil level | |

|Check master cylinder bypass |Check tilt yoke lock |Check steering system | |

|Check drive axle fluid |Check upright adjustment |Check tie rod ends | |

Cleaning and Lubrication

|Disconnect battery |Open contractor panel |drive axle, |check seat brake linkage |

|Remove floor boards |Open hydraulic pump compartment |area under floor boards |lubricate misc. linkage |

|Open SCR compartment |Air clean truck: |SCR control, contact panel, |lubricate units |

|Discharge capacitor |clean packing glands |hydraulic pump and motor | |

APPENDIX G MINIMUM PREVENTATIVE MAINTENANCE, LPG POWERED EQUIPMENT

Visual Inspections

|Check for oil leaks |Check forks and locks |Check for water leaks |Inspect door latches |

|Inspect overhead guard |Check fabreeka pads |Inspect lift cylinder | |

|Inspect load backrest |Check rail patterns |Inspect tilt cylinder | |

|Check and adjust chains |Check tire wear |Inspect packing glands | |

Operational Tests

|Test service brake |Test inching operations |Check for exhaust smoke |Evaluate upright drift |

|Test parking brake |Steering (power and manual) |Check instruments |Check for upright racking |

|Test neutral start switch |Check for unusual noise |Inspect and adjust belts |Check horn, lights and hour meter |

Mechanical Inspections

|Check master cylinder level |Check transmission fluid |Check directional linkage |Check clutch linkage |

|Check master cylinder linkage |Check power steering linkage |Check upright latch | |

|Check master cylinder bypass |Check throttle linkage |Check plugs, points and wires | |

|Check drive axle fluid |Check tie rod ends |Check tilt cylinder mounting | |

Cleaning and Lubrication

|Remove floor boards |Change oil filter |Check transmission filter |Clean/replace sump breather |

|Blow out radiator core |Clean/replace air filter |Check throttle linkage | |

|Air clean unit |Lubricate all zerks |Check battery | |

|Change engine oil |Lubricate free life guide |Lubricate misc. linkage | |

END OF DOCUMENT

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download