Drain Size Capacity
TSM 352 HOMEWORK ASSIGNMENT 06
Due Tuesday, March 25th at 11:59 pm
Drain Size Capacity
1. Determine the size of plastic drain tubing required to drain a 20-acre area, using a 3/8 inch drainage coefficient with the following slopes:
|Slope |Tile Size |Velocity |
|0.10% |8” |0.9 ft/s |
|1.20% |5” |2.4 ft/s |
2. Determine the size of smooth (dual wall) drain tubing required to drain a 20-acre area, using a 3/8 inch drainage coefficient with the following slopes:
|Slope |Tile Size |Velocity |
|0.10% |8 |1.2 ft/s |
|1.20% |5 |3.0 ft/s |
3. a) What size of plastic main with a 0.2 % grade is required for a 40 acre field using a 3/8 inch drainage coefficient?
b) Would this size main be adequate if it had to travel 1200 feet with a 0.1 % grade through a neighboring field to reach an outlet? The required lateral spacing is 100 ft.
c) What should the size of the main be if the neighbor wishes to connect a 20-acre drainage system into the main as it passes through his field?
|Field |Slope |Discharge |Tile Size (Plastic) |Tile Size (Smooth Wall) |
|40-acre field |0.2% |0.63 |10” |8” |
| |
|1200 x 100 sq. ft. (2.75 acre) | |0.04 | | |
|40-acre field and main |0.1% |0.67 |12” |10” |
| |
|20-acre | |0.32 | | |
|40-acre field, main and 20-acre field |0.1% |0.99 |15” |12” |
4. A plastic tile with a diameter of 12 inches is silted to a depth of 6 inches, assuming that the grade in the tile is 0.2 feet per 100 feet:
a. What was the original capacity in CFS? 1.22 cfs
b. What is the present capacity in CFS? 0.44 cfs
c. What size of smooth wall pipe would be required to replace the plastic pipe at its original capacity? 12”
d. If the smooth wall pipes cannot be larger than 8 inches in diameter due to machine limitations, how many 8-inch pipes in parallel would be required to replace the plastic pipe at its original capacity? 2
5. A corrugated metal outlet pipe is to be added to an existing (clay) main tile with a diameter of 10 inches where it enters the ditch. The main with a diameter of 10 inches is laid on a 0.3 grade. Determine:
a. The maximum number of acres drained by the main
76 acres ( using 3/8” drainage coefficient)
b. The minimum grade required for a corrugated metal outlet with a diameter of 10 inches. The roughness coefficient for riveted corrugated pipe is 0.023 – 0.027. 1.3%
c. The minimum grade required for a corrugated metal outlet with a diameter of 12 inches. 0.49%
6. Determine the size of the concrete tile at the outlet of a 50-acre drainage system:
(a) if the drainage coefficient is 3/8 inch and the tile grade is 0.3 percent, and 10”
(b) if the grade is reduced to 0.1 percent. 12”
Lateral Specifications
7. What would be the required spacing for drains placed 4 feet deep in this Drummer Silty Clay Loam, if the system is to be designed to lower a water table initially at the surface by 2 feet in 36 hours?
32’
8. What is the minimum size of plastic tubing that can be used for the situation above, if the laterals are to be 1500 ft long with a slope of 0.1 %?
Drainage coefficient = 0.076 x 2 x 12 /1.5 = 1.216”/day
Flow rate = 1.216/12 x 1500 x 32 /24/60/60 = 0.056 cfs
Tile size = 5”
What would the minimum size be if the drain depth were changed to 3 feet?
Required spacing = 25’
Flow rate = 1.216/12 x 1500 x 25 /24/60/60 = 0.044 cfs
Tile size = 4”
What would the minimum size be if the laterals were designed to have adequate capacity when they were filled with an inch of sediment?
Tile size = 5”
9. What length of plastic tubing is required for draining a 40-acre field if the drains are to be placed 60 feet apart? 29,040’ What is the maximum length of 3-inch laterals that can be used in this field if the slope is 0.1 % and the drainage coefficient is ½ inch per day? 840’
10. A drainage system is to be placed under a drain field for a septic system, to maintain a 3 foot separation between the bottom of the drain field and the water table. The bottom of the drain field and the drains are to be placed 1 foot and 5 feet, respectively, below the soil surface. What should the spacing of the laterals be if the soil type is Flanagan and the system should be designed to from the water table from the soil surface to required separation depth in 6 hours?
5’ This does not seem practical
Ditch Capacity
11. A drainage system is designed to outlet to a trapezoidal ditch with a base with of 15 feet and a 2:1 (H:V) side slope. The drainage area in the watershed above the drain outlet is 640 acres. Determine the minimum height of the outlet above the ditch bottom if the drainage channel is designed to provide
a) Excellent Drainage
Flow rate = 71.09 cfs: Flow depth = 2.02’
Minimum outlet depth = 3.02’ above bottom of channel
b) Good Drainage
Flow rate = 32.65 cfs: Flow depth = 1.26’
Minimum outlet depth = 2.26’
c) Satisfactory Drainage
Flow rate = 23.47 cfs: Flow depth = 1.07’
Minimum outlet depth = 2.07’
Economic Analysis
12. The following materials were used in the design of a drainage system for a 44 acre field. Determine the per acre cost for the materials used in the design. $495.61
|Material |Quantity |Cost |
|4-inch tubing |18500 ft |$1.00/ft |
|5-inch tubing |200 ft |$1.10/ft |
|6-inch tubing |100 ft |$1.85/ft |
|8-inch tubing |500 ft |$2.15/ft |
|10-inch tubing |355 ft |$3.55/ft |
|Fittings |- |$567 |
13. A drainage system with an estimated life of 40 years was installed at a cost of $432/acre. Determine the break even income for each of the following scenarios.
| | A |B |C |D |E |F |
|Depreciation Period |2 years |5 years |10 years |2 years |5 years |10 years |
|Interest Rate |4% |4% |4% |6% |6% |6% |
|Tax Rate |18% |28% |18% |28% |18% |28% |
|Break Even |22.18 |22.90 |22.80 |29.93 |29.85 |31.89 |
|Income ($) | | | | | | |
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- drain size capacity
- section 057300 decorative metal railings
- different types of pump systems
- frequently asked questions carlon sales
- 8 27 99 page 5 1 saudi aramco coiled tubing manual
- gpm gph flow based on pvc pipe size
- design and repair of buried pipe
- sizing selection and installation of pressure relieving
Related searches
- borrowing capacity formula
- borrowing capacity calculator
- debt capacity calculation
- loan capacity calculator
- college stadium capacity rankings
- capacity conversion calculator
- lending capacity formula macroeconomics
- reserve capacity to amp hour
- reserve capacity vs amp hour rating
- 480 volt generator capacity chart
- convert reserve capacity to ah
- customary units of capacity chart