Aluminum Cylinder Block for General Motors Truck/SUV Engines
A Design Study in Aluminum Casting
Aluminum Cylinder Block for General Motors Truck/SUV Engines
Design Study Outline
-- Introduction -- Designing for Performance
Chevy Trailblazer
Alloy Selection
-- Lost Foam Casting
Pattern Design Pattern Production Metal Casting
-- Finishing and Quality Assurance
-- Lessons Learned and Summary
Start the Design Study ! Next
Acknowledgment --
The metalcasting design studies are a joint effort of the American Foundry Society and the Steel Founders' Society of America.
Project funding was provided by the American Metalcasting Consortium Project, which is sponsored by the Defense Logistics Agency, Attn: DLSC-T, Ft. Belvoir, VA, 22060-6221
Return to AFS Home Page
Copyright 2004 by the American Foundry Society All rights reserved. Address comments to: jss@
Last Modified:August, 2004 by STG
In cooperation with
GM Powertrain Casting Development
A Design Study in Aluminum Castings - GM Cylinder Block
Engines for GM SUVs and Trucks
The Application -- In 2002 General Motors introduced a new family of Sport Utility
Vehicles (Chevy Trailblazer, Buick Rainier and GMC Envoy). In 2004 a family of mid-sized trucks (Chevy Colorado and GMC Canyon) was introduced.
q With the higher vehicle weight and additional load capability, the engineering challenge was to upgrade the powertrain with improvements in power, torque, fuel economy, emissions, and NVH (noise, vibration, harshness ) performance, while keeping the vehicle cost affordable and the weight down.
q A comprehensive engineering study was done to select the best engine configuration, considering V-8, V-6, and Inline 6 designs. The study determined that the Inline design had the following advantages -- simplest design, lowest number of parts, inherently balanced, lowest cost, and best manufacturing flexibility.
q The Inline 6 was designed to have the power and torque of a V8. The inline 5 was designed to match the performance of a V6. Both engines provide improved fuel economy without sacrificing performance
Inline 5 Cylinder 3.5 liter Engine
GMC Canyon
Back Next
2
Copyright 2004 by the American Foundry Society All rights reserved. Address comments to: jss@ Return to AFS Last Modified:August, 2004 by STG Home Page
In cooperation with
GM Powertrain Casting Development
Page 1
A Design Study in Aluminum Castings - GM Cylinder Block
Engine Design
The inline design is applicable to 6, 5, and 4 cylinder (4.2, 3.5 and 2.8 Liter displacement) engine configurations.
q The SUVs come equipped with the six cylinder version and the mid-size trucks are equipped with the four or five cylinder versions of the engine family.
q All three inline engines use the Vortec cylinder design and have a 93mm bore x 102mm stroke with a double overhead cam using 4 valves per cylinder.
q The engines operate with a 10:1 compression ratio, but still use regular unleaded fuel (87 RON).
q The three inline engines have 75% part commonality.
GM Vortec Inline Engine
Back Next
3
Copyright 2004 by the American Foundry Society All rights reserved. Address comments to: jss@ Return to AFS Last Modified:August, 2004 by STG Home Page
In cooperation with
GM Powertrain Casting Development
Page 1
A Design Study in Aluminum Castings - GM Cylinder Block
Engine Specifications
The performance specifications for the three engines are --
Cylinder
6
5
4
Count & Cylinder Cylinder Cylinder
Displacement 4.2 Liter 3.5 Liter 2.8 Liter
Peak Horsepower
275 HP @ 6000 RPM
215 HP @ 5600 RPM
170 HP @ 5600 RPM
Peak Torque
275 FTLB @ 3600 RPM
225 FTLB @ 2800 RPM
175 FTLB @ 2800 RPM
Base Engine 184kg Weight
178 kg 150 kg
The newly designed inline engines are significantly lower in weight than previous truck engines with the same performance specifications.
Back Next
4
Copyright 2004 by the American Foundry Society All rights reserved. Address comments to: jss@ Return to AFS Last Modified:August, 2004 by STG Home Page
In cooperation with
GM Powertrain Casting Development
Page 1
A Design Study in Aluminum Castings - GM Cylinder Block
Aluminum Castings for the Engine
One of the key weight saving features in the engine design is the use of a cast aluminum cylinder block with cast iron cylinder liners.
q The cast iron liners (with ground outside-diameter) are press-fit into the precision bored aluminum cylinder block. This provides optimal heat transfer into the cylinder block.
r The iron liners provide the wear resistance needed for improved durability.
q The installation process for the liners includes chilling the liner prior to placement and sophisticated precision force monitoring to ensure proper installation.
q After installation, the ID of the iron liner is bored to a mass-saving 1.5 millimeter wall thickness.
Back Next
5
Copyright 2004 by the American Foundry Society All rights reserved. Address comments to: jss@ Return to AFS Last Modified:August, 2004 by STG Home Page
In cooperation with
GM Powertrain Casting Development
Page 1
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- engine engine mechanical 4 8l 5 3l and 6 0l 6 1 engine
- 3 0l service manual revision all power labs
- five generations of refinement state of the art
- break in procedures for remanufactured engines
- balance shaft caution on 2004 2012 gm 3 5 3 7l dohc
- lt1 based crate engine control system
- engine industrial marine 3 0l 7a 12b 1 table of contents
- chevy engine specifications
- aluminum cylinder block for general motors truck suv engines
- 5 7 parts manual
Related searches
- general motors dealership locations
- general motors dealerships near me
- local general motors dealers
- general motors rebates and incentives
- general motors rebates and discounts
- general motors incentives 2019
- general motors rebates 2019
- general motors incentives 2020
- general motors discounts and incentives
- ford truck crate engines turnkey
- general motors payoff address
- general motors salary grades