Eileenkristine | Smile! You’re at the best WordPress.com ...



Velez College

F. Ramos St., Cebu City

Pediatric Splinting

Submitted by:

Abarra, Eileen Kristine S.

Alturas, Angela Cristy A.

Bacayo, Nicole Christianne Mae B.

Balbuena, Mazie Therese J.

Beloria, Euka Maria R.

Buñing, Rey Xristan B.

Buo, Queenie Ann O.

Cabahug, Erika Marie V.

Caballero, Khisha Joan A.

Cabañero, Debbie Rose D.

Chiongbian, April Grace

Clarin, Cadiene Concepcion C.

Daral, Allaine Marie C.

Dimitiman, Cristito Jr. D.

Estores, Frances Vince V.

Go, Krishia

Jung, Jung Won

Submitted to:

Mr. Von Bryan Darcera

September 24, 2012

PEDIATRIC SPLINTING

Similar to fabricated splints for adults, splints made especially for children may be used to prevent deformity, to increase function or to do both. However, splinting children involves more than just making a smaller splint pattern. The purpose of this topic is to guide the beginning therapist in applying splinting knowledge to the special needs of children with developmental disabilities or birth defects of both a neurological and orthopaedic nature, such as cerebral palsy or arthrogryposis multiplex congineta. The resting hand, weight-bearing wrist, MacKinnon, thumb and serpentine splints are basic designs that serve as a foundation for pediatric splinting. Modifying these designs or creating entirely new ones should be considered by the therapist to ensure that they meet the needs of a child. However, it may not be possible that all splinting goals may be achieved with just one splint. Before splinting decisions are made, the therapist must first establish overall treatment goals based on the frame of reference appropriate to the child and the environment. The chosen splint then becomes a component of the treatment program, which includes goals for improving function and the child’s ability to participate in childhood occupations, including play, self-care, and such productive activities as schoolwork. Splint designs are compatible with neurodevelopmental treatment (NDT), rehabilitative or biomechanical FOR. Splinting decisions must be compatible with the lifestyle, values, and culture of the child and the family, as well as child’s home, day care, community, and school environments.

Splinting a child is different from splinting with adults in many respects, including:

1. Abnormal muscle tone has been present since birth or infancy and may differ qualitatively from abnormal muscle tone acquired after disease or injury.

2. The child experiences the dynamic process of maturational and neurological development, which has a continuous effect on the acquisition of functional hand skills.

3. Children experienced continued growth of the upper extremities. As children grow, splints fit and create pressure. During growth spurt, the risk of deformity or skin breakdown may increase as a result of bone growth that exceeds growth or lengthening of muscles and soft tissues because of spasticity. Deformity may also occur secondary to a splint that has been outgrown and no longer fits properly.

4. Many children must rely on adults, such as parents or teachers, to apply and remove their splints. Therefore the level of understanding and cooperation of these adults is a factor.

5. Children have a low tolerance for interference by adults and the imposition of a piece of equipment (splint) which is unfamiliar to them. Their cognitive level may be insufficient for them to understand abstract concepts such as “prevention” or to comprehend cause-and-effect relationship (if you wear this splint, then your hand will work better). They may resist holding still, become fearful and cry, or be able to cooperate only for brief periods of time because of short attention span. Any or all of these factors may create great challenges to the fabrication and application of the splint or splints for children.

6. The placement and molding of a splint on a child is more difficult than on an adult because the child’s hand is much smaller in proportion to the therapist’s hand.

DIAGNOSTIC INDICATIONS

The focus of this chapter is on splinting the child with a developmental disability or congenital anomaly. However, many of the principles and splints described also apply to adults with developmental disabilities. Developmental disabilities include a wide variety of chronic conditions that are evident at birth or during childhood and that interfere significantly with development and functional abilities (Yamamoto, 1993). Many developmental disabilities, such as cerebral palsy, are accompanied by central nervous system dysfunction and abnormal muscle tone. Central nervous system dysfunction can be the result of many types of brain injury such as an intracranial hemorrhage, hypoxia, infections, tumors, or trauma. Abnormal muscle tone can include increased, decreased or fluctuating tone and presents a number of splinting challenges. Lower motor neuron dysfunction may also occur at birth as a result of excessive stretch to the brachial plexus during delivery. Depending on the nature and extent of the nerve damage, this may result in developmental hand dysfunction.

Other diagnoses in children for which splinting may be indicated include congenital defects or anomalies of the hand or upper extremity, which are generally due to malformations of the musculoskeletal system. These may include finger flexion contractures, soft-tissue or bony fusion (syndactyly), or dysplasia of the ulna or radius. Another congenital or birth defect that requires orthotic intervention is arthrogryposis multiplex congenita. “Arthrogryposis multiplex congenital is not a specific disorder but rather a symptom complex of congenital joint contractures associated with both neurogenic and myopathic disorders… The main feature shared by these disorders appears to be the presence of severe weakness early in fetal development, which immobilizes joints, resulting in contractures.” (Banker, 1985, page 30). Programs that involve early passive stretching and serial splinting of contracted joints are recommended (Sala, Rosenthal, & Grant, 1996; Williams, 1986; Bayne, 1986). Splints, such as a dynamic elbow flexion splint, have also been developed to compensate for lost muscle power (Kamil & Correia, 1990).

Children with developmental disabilities or congenital anomalies often present with indwelling thumbs (thumbs held adducted into the palm). This may be the result of abnormal muscle tone, weakness, or abnormal anatomy of the hand. To effectively grasp and manipulate objects, it is crucial that the thumb be positioned in opposition. Splinting, along with active movement, is often required to effectively position the thumb in opposition for grasp and optimal hand function.

Juvenile rheumatoid arthritis (JRA) is a systemic rheumatic disease that causes major disabilities in children younger than 16 years old. Children with JRA may present with pain, fatigue, and reduced range of motion (ROM). These symptoms often result in difficulty performing school tasks and activities of daily living. In addition to medical management,”… forms of treatment may include splinting, active and passive range of motion of the joints, and monitoring each joint to maintain maximal function and prevent deformity” (Gordon, Schanzenbacker, Case-Smith & Carrasco, 1996, p. 124).

In summary, a number of pediatric diagnoses may indicate a need for splinting. However, the final splinting decision is made on the basis of the limitations in specific movements, the type and severity of abnormal muscle tone, the extent of soft-tissue and bony involvement, the child’s functional level, the child’s environment, and the frame of reference guiding therapy, rather than on a specific diagnosis.

ASSESSMENT

Before fabricating a splint, the therapist must complete a comprehensive assessment. These factors should be considered:

Engagement in Childhood Occupations

Clinical observation of the child engaging in childhood occupations is necessary to determine the overall direction of the intervention program and whether and how a splint will contribute to that intervention program. The child and family attach meaning to different activities and occupations, and it is the accomplishment of these occupations that ultimately determines the success of the intervention program. On the basis of the child’s occupations, the therapist can determine the relative emphasis for individual components.

Muscle Tone

The quality and distribution of muscle tone should be assessed at rest and during functional activity. The therapist should also determine whether the amount of tone varies according to the child’s mood, physical health, amount of effort exerted, or state of alertness.

Range of Motion

The therapist should measure both active and passive ROM and compare measurements with those taken previously to determine whether range is increasing, decreasing, or remaining the same. The position of the joint and the level of comfort of the patient must be taken into consideration as well.

Contractures

The therapist should discriminate between types of joint end feel. When tightness of a joint is primarily the result of muscle and soft-tissue shortening, with full passive range still possible with effort, this effect is known as soft end feel. When the joint cannot be moved to the end of passive range, it is said to have a hard end feel. When the latter cannot be obtained, it is known as a contracture. A limb with a contracture is also said to have a deformity.

Active orthotic management or splinting during childhood may prevent many contractures and resulting deformities thus improving quality of life for children and their respective families. Early orthotic intervention is also usually less costly.

Understanding the possible physiological mechanisms for the formation of a contracture can assist the therapist in splint design and establishment of wearing schedules. Preventing contractures, or minimizing their severity, is one of the most important functions of splinting for children with developmental disabilities or congenital anomalies.

Integrity of Skin, Bones and Circulatory System

Osteoporosis in children occurs due to lack of weight bearing while bones are growing. In splinting a child with osteoporosis, stress to the bones could cause a fracture thus extreme care must be given. Children with tightly fisted hands may develop skin breakdown in the palms or between the fingers so maintenance of skin hygiene becomes a priority. Other children may experience pain in certain positions; have sensitive skin; or have poor circulation, which would require careful monitoring of the child’s skin temperature and color during splint wear. Some children may have feeding problems and may be underweight. They have more difficulty tolerating pressure on bony areas due to little subcutaneous fat.

Functional Use of Upper Extremities

The therapist should evaluate components of reach, grasp, manipulation, release, bilateral hand use, and tactile and proprioceptive reactivity and discrimination. It is important to evaluate function in different positions as this gives crucial information about the proximal stability needed for effective distal function of the hand. Sensory system modulation should be observed because this affects the therapist’s approach to the child and influences splint selection and fabrication. The therapist should also obtain information about the child’s cognitive level as this affects hand use. An objective measure of hand function, such as a criterion references assessment tool, must be used to periodically reevaluate and compare the child’s performance over time along with a qualitative description of how the child moves and performs.

Environment and Family Considerations

The fabrication and monitoring of a child’s splint may occur in any of the environments in which the child lives, rests, plays and is productive in. When selecting and designing a splint, persons who are responsible for donning the splint must be considered. Simplicity of design is most desirable especially if multiple care providers are involved. Compliance with using the splint is likely to decline as the complexity with the donning and wearing schedule increases.

Splinting in the intensive care units of the hospital must be fabricated with minimal handling of the child and while navigating carefully around tubes and monitors. The use of splints must be incorporated, and not cause difficulty, in the daily medical care provided by nursing staff. The therapist must also be familiar with the child’s medical condition and be able to recognize signs of stress that can be harmful to the child.

In the school environment, splints must contribute to the child’s ability to benefit from a specially designed program of instruction. It is important for a child to be able to reach, grasp, carry, manipulate, and release learning materials and other objects in order to function in the school settings. The therapist should include the purpose of a splint as a part of educationally related occupational therapy described by the individualized education plan.

Information about the home environment should be obtained from interviews with significant others and a home visit, if possible. Splints with wearing schedules that are incompatible with family schedules or cannot be understood by family members will be ineffective. The therapist must individualize the splint design and wearing schedule to fit the family’s strengths and needs.

OVERVIEW OF THE SPLINTING PROCESS

Prepare the Child

Position the child so that the effects of abnormal tone and postural reflexes on the arm and hand are at a minimum. It is important to provide external stability through equipment or handling for children who have not acquired internal stability of proximal joints. For the infant or young child, it may be possible for the parent to hold the child and provide external stability with the therapist’s instructions.

It is also important to reduce the child’s fearfulness and maximize his or her cooperation. The therapist should have toys, music, books, stickers or other materials to establish reciprocal interaction with the child before starting the fabrication process.

With an infant, the therapist can talk in a soothing voice and touch the child in a playful manner. With an older child, the therapist can show the child what to expect by first fabricating a splint on a doll or stuffed animal or by making thermoplastic jewelry or other play objects. When appropriate, the child should be given opportunity to touch and feel the material while it is warm and soft and again after it become cool and hard. The child’s response to tactile stimuli should be noted, and if signs of tactile defensiveness occur the therapist should follow sensory integration guidelines for improving sensory system modulation.

Giving the children a role to play in fabrication process may increase their cooperation. Although preparing the child may take a few extra minutes at the beginning of a splinting session, it can save hours of frustration in having to reschedule or remake a splint because of lack of cooperation.

Prepare the Environment

It is recommended that the therapist plan to have a second pair of adult hands to help with the fabrication process. This additional person might be a parent, teacher, professional, or another therapist. This is especially important if the child has increased tone, is not able to follow verbal instructions, or likely to be uncooperative. The therapist must clearly explain the helper’s role so that efforts assist the process and not hinder it. This usually involves maintaining the child’s overall position, calming or entertaining the child, holding the arm just proximal to the joint being splinted, or stabilizing the material once in place and when it is cooling.

Selection of Splinting Materials

- Pediatric splint may be made of many different types of materials

- Thermoplastic materials- commonly used for the fabrication of static splints or those that require restricting motion at certain joints

- Examples of thermoplastic material used:

• QuickCast- thermoplastic material thinner than 1/8 inch

• Adapt-It Thermoplastic Pellets

- Soft splints- are commonly made of materials such as neoprene, leather, or webbing. It may not totally immobilize joint but it provide support and comfort

- Children with athetosis or involuntary flailing movements should be protected from possible harm from the splint by selection of a soft material or by covering a thermoplastic material with a mitt or sock

- When splinting with neoprene, therapist should be alert to the possibility of skin irritation or rash. Skin contact with neoprene poses two dermatological risks: allergic contact dermatitis and miliara rubra. It is recommended that therapist should screen the patients for history of dermatological reactions, instruct the patient to discontinue use and inform the therapist if a rash, itching, or skin eruptions occur, and report cases of adverse skin reaction to the manufacturer of the neoprene material. Therapist are also recommended to limit their own exposure to neoprene and neoprene glue because of the exposure to thiourea compounds that are thought to contribute allergic reactions

- Thermoplastic material with high plastic content have more conformability whereas materials with a high rubber content have less stretch

- When making a splint that counteracts the forces of spasticity, it is important to select a thermoplastic material that resists stretch because it is necessary for the therapists to apply considerable pressure to obtain the desired position of the wrist, thumb, and fingers. Usually the rubberlike thermoplastic material is necessary when one is splinting against spasticity

- When working with a child, choose a material with a high degree of memory

- When splinting a neonate or young infant, the therapist should use material that is 1/16 inch or 3/32 inch thickness

Patterns

- Patterns are made for each splint on each child, depending on the therapeutic goal of the splint and the child’s characteristics

- Many children with abnormal tone may be unable to lay their hands on the table surface for tracing. In this case, the pattern must be held under the extremity in whatever position is least stressful. The therapist may also consider using uninvolved contralateral side to start a pattern, given there is some symmetrical of anatomy

Heating the Thermoplastic Material

- The therapist should heat the water to the temperature range recommended by the manufacturer

- After cutting out the splint, it may be necessary to reheat the plastic to obtain the desired degree of pliability before the molding process

- Before placing the plastic on a child’s extremity, the therapist should dry off the hot water and make sure the plastic is not too hot

- The child’s arm and hand can be moistened with cold water just before molding, or the therapist can wait longer for the plastic to cool

- Some therapist use stockinette to protect the extremity

Hastening the Splinting Process

1. Rubber based plastics, which are necessary to resist stretch, are somewhat slower to harden

2. Once plastic is in place on the extremity, an ice pack can be rubbed on the splint to hasten the setting process.

3. A rubber glove filled with ice chips can easily serve the purpose

4. After partially hardened, the splint can be carefully removed and put into a pan of ice water or placed under a faucet of cold running water to finish hardening.

5. A spray coolant may be used, but only with great care to spray after the splint is off the child and with the spray directed away from the child

6. The use of the coolant spray should be avoided with children who are unable to keep their heads turned away from the direction of the spray and those who have frequent respiratory problems

7. Theraband roll that has been cooled in a freezer can help form the splint, especially forearm. This will accelerate the cooling process at the same time

8. If not available, an Ace wrap can be useful to hold the forearm trough in place while the therapist works on the hand portion of the splint, although this maintains heat and may increase setting time.

9. The therapist should not apply the wrap or Theraband too tightly and should flare the edges of the forearm trough away from the skin after formation of the splint.

Padding

- Necessary over bony areas to prevent skin problems

- Does not compensate for pressure resulting from a poorly made splint

- Padding takes up place, a factor that the therapist must take into account before formation of the splint

- Types: closed- and open-cell foam; and gel products

- Pressure relief padding with a gel center is useful in protecting bony areas for children with little subcutaneous fat

- To ensure proper fit, the therapist should lay the padding on the child’s extremity before molding the plastic or place it on the thermoplastic material before molding the splint

- When molding the padding, the stretch of the thermoplastic material and contourability may be compromised. Therefore the therapist should add padding only when necessary

- Becomes soiled and needs to be replaced

- Alternative: cover the prominence with small amount of firm therapy putty before forming the splint. The putty creates a built-in bubble and is removed from the splint after cooling

- Thin forms may also be useful to create friction and reduce migration or shifting of splints, or for covering edges

- Microfoam tape is useful for this purpose, especially on small splints

Strapping

- Strength, durability, elasticity and texture when strap is against skin should be considered

- Straps with sharp edges should be avoided with younger children and those with sensitive skin

- The wider the strap, the more force is dispersed, as long as the entire strap with is in full contact with the skin

- Must be cut narrower, especially around the wrist and fingers, to proportionate to the size of the child’s hand

- Secured at each end with hook Velcro, which is attached to the splint. This allows them to be easily replaced when they become solid, which is important if the child drools on the splint or mouths it

- Loose straps easily becomes lost and many times are not placed on the splint at the correct angle or location

- Alternative: adhere strap at one end with a rivet or strong contact adhesive

- When soiled, straps must be removed by the therapist and a new strap attached

- A great deal of creativity is need to keep the little “Houdinis” in their splints

- Kid proof methods: Shoelaces, buttons, or tape

- Lacing can be done by punching holes along the lateral edges of the splint and lacing with wide decorative shoelaces

- Thx should place padding under the laces against the skin

- “Bow Biter,” a plastic device to hold the laces in place and available in the children’s department store

- Sock puppet worn over the splint may be used as a camouflage

- Care must be taken not to provide any attachment that the child could bite off and swallow

Providing Instructions for Splint Applications

One must understand the splint’s:

• Purpose

• Rationale for using splint

• Precautions

• Risks of incorrect usage

These must also be known to others responsible for the child, such as:

• Teachers

• Nursing staff

• Parents

• Child caregivers

Complex splinting = more detailed and explicit instructions needed.

Parents and major care takers should already be familiar with the purpose and rationale because their input is necessary for the splint design. Written instructions and along with a phone number to call is important to be provided by the therapist. Demonstrations of steps and practice in applying the splint under supervision are also important.

A photograph of the child's forearm and hand showing the correct position is an effective teaching tool thus considering first any confidentiality matters. Instructing caregivers to inspect skin every time splint is removed to assess splint for tightness is also important.

Wearing Schedules

This may vary according to the purpose of the splint, tolerance, musculoskeletal status, occupations and daily routines of the child. Splints may be worn for long or short intervals; day, night, and functional activities. Gradually increasing the time of wearing the splints will increase the child's tolerance for the splint.

Splint for functional use f the hand is worn during the times of functional activities. Splint for tone reduction is worn after activities of the child. Splint for preventing contractures is worn when the child is not engaged in any activity. Splint for treating existing contractures is worn for long periods of time. Time wearing for the splint that is more important than wearing it continuously or intermittently is in the span of 24hrs.

Clinical judgment, based on the education, learning through reading, continuing education, experience, and feedback from child and parents are the basis of making a wearing schedule of the splint. These schedules will only work if the splint is placed on the child during the times recommended. Including these in the child's regular routine will increase compliance because it becomes less of a chore to the child's SO's. Evaluations of the splint will take place for the child's ROM status may change thus requiring necessary modifications of the splint.

Precautions

Skin inspections should be made frequently at the initial wearing phase. If a distinct red area or a generalized redness does not disappear within 15-20mins after splint removal will indicate excessive pressure and the need for revisions. Problems associated with joint compression, pressure on the nerves, compromised circulations, and dermatological reactions must be notes by the therapist.

Evaluation of the Splint

Reassessment of the splint must be done on a regular basis to ensure proper fit and function. The care provider must be able to put the splint an hour before the reassessment so that the therapist can observe how the splint is put on and whether the splint migrates out of position after initial donning. A poor fitted splint can cause harm to the patient. This applies to all pediatric splints.

RESTING HAND SPLINT

Purpose

• Prevent contracture or deformity

• Prevent an existing deformity from becoming worse

• gradually improve or reduce deformity

• Children with moderately to severe increased tone or those severely decreased tone that have no active movement have the greatest risk of developing a contracture.

• Maintenance of skin hygiene is needed for those with increased muscle tone and tightly fisted hand.

Features

Components:

• Forearm trough

• Pan of fingers

• Thumb trough

• C bar

- Considering the function of the thumb, therapist should attempt to rotate the 1st metacarpal in palmar and radial abduction.

- For children with moderately to severely increased tone, the functional position may not be possible. The purpose is to prevent or reduce joint deformity; splint should provide as much elongation of the tight muscles as possible without causing excessive stress.

- The child should be able to tolerate wearing the splint for several hours at a time to obtain maximum benefit.

- If the splint places the hand in maximum passive of motion, the forces compromise circulation, skin breakdown, elicit pain, and reduce length of time the child can tolerate.

- The splint should place the wrist joint in submaximum range to allow extension of the fingers.

- If flexor spasticity is severe, serial splinting is necessary.

- Therapist can determine the best splinting position by handling the child’s extremity and feeling the amount of passive resistance.

Process to Fabricate a Resting Hand Splint

Thermoplastic material selection

- Low temperature thermoplastic that resist stretch.

- Higher rubber content will have desired working characteristics.

Pattern

- Include measurements and markings of landmarks.

- After pattern is drawn and cut out, therapist fits it to child for further modifications.

- While making the pattern and molding, position the child to minimize the effects of abnormal tone and postural reflexes.

Padding

- Padding places some restrictions on forming the splint and keeping it clean, it should not be used unless the child is risk of skin problems.

- Creating bubbled-out areas over bony areas may be sufficient to avoid skin problems.

Forming the splint

- Before placing, pre-stretch the edge of the splint that forms C bar.

- The therapist should then place the soft plastic on the child’s extremity to conform to the web space of the thumb.

- Form the splint into palmar arches and around the wrist and thumb.

- To obtain the desired contour and fit, the therapist may need to be aggressive when molding into the palm and around thenar eminence, especially working against spasticity.

- The therapist must form the splint so that the bulk of pressure positioning the thumb is directed below the thumb metacarpal joint distributed along the thenar eminence to avoid hyperextension and dislocation of thumb in MP joint.

- Thumb trough should cradle the thumb and extend about ½ inch beyond the end of thumb.

- IP joint of thumb should be slightly flexed.

- C bar should fit snugly into web space and contour against the radial side of index finger.

Forearm Trough

- Edges of the trough should not be too high. High edges cause bridging of the straps.

- Bridging of the straps makes it difficult to keep the forearm securely in place which may cause forearm rotation on the trough or the shifting of the splint distally. The position of the wrist, fingers and thumb will be compromised

Pan

- Require reheating because controlling all the joints at the same time is often difficult

- Distal portion of the pan should extend about ½ inch beyond the finger tips

- Proximal and distal transverse arches should be followed when forming the curve of the pan

Straps

- Correct placement of straps is as important as correct formation

- Straps and splint must work together to create the necessary leverage and to distribute pressure

- Optimum location and angle of each strap should be determined in relation to the forces being applied by the abnormal muscle tone.

- Forearm trough

o Two straps for older child

o One wide strap may be sufficient for a smaller child or an infant

- If considerable wrist flexion is present

o Two straps is necessary to provide 3 points of pressure to secure the wrist

▪ Directly across the wrist

▪ Angled from the thumb web space across the dorsum of the hand and secured proximal to the MCP joints on the ulnar side

- If considerable finger flexion is present

o Straps may be needed across each of the three phalanges

o Add a strap between the MP and IP joints of the thumb

- Make straps narrower if splint is for a young child

Adaptations

- Resting hand splint provides a basic form for positioning the child in good alignment

- Deviate from the basic form to truly meet the needs of the child

- Finger separators

o Abduct fingers and assist in tone reduction

o Bubbling the material between digits

o Attaching a roll of thermoplastic material between the digits

o Can also be made from Adapt-It Thermoplastic Pellets

▪ Soften pellets in hot water and knead them together to the shape and size

▪ 100% memory and attached in the same way as any other thermoplastic material

▪ Work well when individualized finger separators are needed

- dorsal based resting splint

o allow sensory input to the palm of the hand

- infants with congenital finger contractures

o resting hand splints

o when all digits are not affected,, splint may be altered to free non-affected digits

- resting hand splints may be made with alternative materials

o semirigid pliable material

▪ for neonates

▪ less likely to cause abrasions

o Kushionsplint

▪ Semirigid low-temperature material lined with terry cloth

▪ Heated using conventional oven

o Permagum

▪ Silicone rubber dental impression material, mold into shape for neonatal splints

o Adhesive cloth tape

▪ Several layers may also be an effective semirigid support

o High-density foam

▪ Alternative to decreasing upper extremity hypertonicity in children with extremely high tone

Precautions

- Consider biomechanical principles of force distribution

- Monitor for any undesired lateral forces on the fingers or wrists

- Be aware of any circulation compromise or pressure on the nerves

- Be astute in observations and elicit important information from the child, parent, or caregiver

Applying precautions for child with increased tone:

- Shorten initial wearing time to 15-20 minute intervals on the first day

- Carefully inspect the skin

- Distinct read area or generalized redness on the skin that do3es not disappear within 15-20 minutes after splint removal indicates excessive pressure

- If no pressure areas are present, increase the wearing time to 20 minute intervals

- Wearing time is increased by adding 15 to 30 minutes of wearing time until maximum wearing period for the child is reached

For moderately to severely increased tone

- Maintaining integrity of the MP joint of the thumb

- Direct pressure below the MP joint of the thumb

- Distal force to the spastic thumb can result hypertension and dislocation of the MP joint

Wearing Schedule

- Determined on an individual basis

- The more serious the threat of deformity, the longer the splint is worn each 24 hours.

- Splint is removed for periods of passive ranging, active movement, ad opportunities for sensory experiences

- Flow chart or algorithm for making clinical decisions

- Describe the biological basis for limitations in joint ROM and increasing ROM

- Basis for limitations in joint ROM and increasing ROM

- Primary basis for using splints to increase ROM is that by holding the joint at or near its end-range over time, therapeutic tensile stress is applied to the restricted periaarticular connective tissues and muscles.

- Induces remodelling of tissues to a new, longer length, which allows increased ROM

- Remodelling

o Biological phenomenon that occurs over long periods of time rather than a mechanically induced change that occurs within minutes

- Work on functional activities immediately after removal of the resting hand splint

- Splint should be removed more frequently or for longer periods of time

Providing Instruction for Splint Application

- Caregivers should understand

o Purpose

o Precautions

o Risks of incorrect usage

o How to reach the therapist

Evaluation of the Splint

- Self-evaluation can be used to evaluate the finished splint

- Fit of the splint should be reviewed at regular intervals

- Splint’s effectiveness in accomplishing state goals and outcomes should be re-evaluated on an on-going basis

WEIGHT BEARING SPLINT

- Positions the hand in the most effective position for weight bearing activities.

- Requires significant wrist extension for effective use.

- Use as a therapeutic tool, generally with children who have mild to moderate spasticity in their upper extremities.

- Worn only during therapy sessions.

- According to Lindholm, (1986), the splint positions the wrist in extension to counteract the usual position of wrist flexion resulting from spasticity.

- This position allows weight bearing through the heel of the hand

- The splint positions the hand to allow normal weight bearing through the lateral borders of the hand and the fingertips.

- An effectively positioned hand allows the child to work on more proximal control.

- The splint serves as an assist for positioning the hand, while the child is performing weight – bearing activities.

- During therapy, the splint allows the therapist to focus less on the hand and fingers and more on facilitation or inhibition techniques of the upper extremity

Features

- The splint was originally designed as a hand – based splint.

- More stability is provided when the splint is fabricated with a forearm trough.

- It has a similar in design to the resting hand splint; however, there is more extension at the wrist, and the thumb is in more radial abduction.

Pattern

- The pattern for the weight – bearing splint is similar to that for the resting hand pattern.

• However, extra space is provided when tracing around the fingers and thumb.

• The web space is not tapered.

- The pattern should look like a mitt for the hand.

- If a forearm trough is added to the splint design, it should extend two thirds the length and half the circumference of the forearm

Forming the Weight – Bearing Splint

- Mold the splint on the volar surface of the hand.

- The PIP joint and DIP joint should be in slight flexion and the thumb in radial abduction.

- The wrist should be in 450 to 500 of extension.

- Much attention should be given to the palmar arches by positioning the hand in a cupped position.

- A small ball that fits comfortably in the child’s hand can be used to reinforce the arches.

- A wide strap over the IPs will aid in keeping the fingers on the mitt.

- A diagonal strap over the wrist reinforces the wrist position.

- Straps should be placed proximally and distally on the forearm trough.

Precautions

- Requires adequate wrist extension.

- ROM must be obtained before it is fabricated.

- When the wrist is in extension, the fingers often attempt to curl into flexion.

- Attention should be given to stabilizing the fingers in slight abduction.

Adaptations to the Weight – Bearing Splint

- Slits should be made in the hand portion the splint to maintain stability of the fingers.

- This is accomplished by threading the strapping material through the slit and looping it over each joint.

- A dorsal hood may be fabricated by draping the thermoplastic material over the dorsum of the hand to ensure stability at the hand.

- If additional concerns exist with respect to stabilizing the wrist and dorsum of the hand, the wrist and the forearm may be covered with thermoplastic material.

- This will create a clam shell type of splint.

- Since considerable pressure may be present, the dorsal piece of the splint may require padding.

WRIST SPLINTS

Providing proximal stability at the wrist, the splint allows for improved control of distal finger movement for grasp and release. When a therapist uses a wrist splint for a child who has tightness of the long finger flexors, the splint may have to position the wrist in slight flexion. Because of the tenodesis effect, the wrist splint may not be appropriate if the finger flexors have severe tightness causing a fisted hand posture.

- If the child has only mildly increased tone or is hypotonic, a soft wrist splint with a reinforcement component over the wrist may be preferable.

- If tightness is also present in the opponens muscle, a splint that includes a thumb trough may be indicated.

The thermoplastic wrist splint can be either volarly or dorsally based. The volar design is more effective if wrist flexion is difficult to control; however, it covers the palm of the hand, thus reducing sensory input and creating more bulk in the hand. The dorsal design allows more sensory input in the palm but may be more difficult to construct when the child has wrist and finger flexor spasticity. If the palmar bar is too narrow, it can be dangerous and painful

Features

Process to Fabricate a Volar Wrist Splint

Materials

- A thermoplastic material that resists stretch is frequently desirable when the therapist positions the wrist of a child with spasticity.

- When the purpose of a wrist splint is to serve as a base for attaching pointers or holders.

Pattern

- After tracing the child’s extremity, the therapist make the splint makes the splint pattern.

Forming a Wrist Splint

- The splint should follow the contour of the palmar aches as they are configured during grasp. The splint should not interfere with MCP flexion or thumb opposition.

- The therapist rolls the edges around the thenar eminence and MP bar.

Straps

- Usually two straps secure the forearm tough and one strap secures the hand. The hand strap is angled from the ulnar side of the metacarpal bar to hypothernar bar.

Precautions

- The splint should distribute pressure to avoid skin irritation.

- The splint must stabilize the forearm so that the splint does not shift during use.

- The splint should not interfere with thumb opposition or MCP flexion of the fingers.

Wearing schedule

- The therapist should consider the child’s therapeutic goals, occupations, and the extent of functional hand skills with and without the splint.

- The child wears the splint during activities that require grasp and release that can accomplish more easily while wearing the splint.

Evaluation of the Splint

- The therapist can use self-evaluation form to determine whether the fabrication of the splint is correct.

- The therapist should also perform frequent, on going re-evaluation of the splint’s effectiveness and the child’s functional hand skills.

Adaptations to the splint

A unique adaption to the wrist splint is the attachment of pointers, crayon, holders, or other assistive devices. When designing a pointer, the therapist should angle it so that the pointer is within the child’s visual field. When possible, the therapist makes a finger trough to position the index finger pointing, thus allowing sensory feedback to the tip of the index finger after contact is made with the target.

Some children may benefit from the addition of a spiral strap to facilitate partial supination while wearing the wrist splint. This can be accomplished by dorsum of the hand over the wrist and forearm and attaching it to itself just proximal to the elbow.

MACKINNON SPLINT

- A semi dynamic wrist splint that facilitates wrist extension while inhibiting finger flexor tone

- Provide touch pressure to the metacarpal heads to inhibit flexor tone while providing stretch on the intrinsic to facilitate the muscles.

- Used with children who have mild to moderate hyper tonicity and aids in positioning the hand for gross grasp and finger isolation activities.

- Original design with dowels and nails.

Features

- MacKinnon splint provides an inhibitory components to the fingers, provides support for wrist extension, and also aids in thumb position

- It has metacarpal bar that exerts pressure across the metacarpal heads.

- Bar is attached with flexible tubing to a dorsal forearm trough.

- Attachment site may be also in wrist bar but more stability is gained in forearm trough

- Often visually appealing and less restrictive, thus giving the child more opportunistic for sensory experiences.

- Splint Increases grasp and bilateral hand.

- Improved hand function in children with hemiplegia

Process to fabricate a modified MacKinnon Splint

- Constructed of a thermoplastic material with moderate stretch as used with the resting hand or wrist splint.

- A piece of ¼-inch flexible aquarium tubing is needed for the semi dynamic wrist support.

- Closed-cell padding may be used to help prevent migration of the forearm piece and for increased stability of the splint on the forearm

Pattern

- Metacarpal bar is formed from a rectangular piece of thermoplastic material.

- Rectangle is equal to the length of the distal palmar crease and wide enough to roll and self-adhere.

- Forearm trough is a rectangular covering 2/3 of the length of the forearm and ½ of the circumference.

- Length of the tubing is the distance from the attachment site on the dorsal side of the forearm trough, across the volar aspect of the metacarpals and back to the dorsal attachment site

Forming Splint

- Fabricate MC bar by rolling the tubing in the rectangular thermoplastic material.

- Diameter of the palmar bar depends on the size of the child; it ranges from ½ to ¾ inch.

- Hold the bar straight until it hardens, simulating wooden dowel. Position the wrist in slight extension.

- Place MC bar across the MC heads, and pull the tubing to maintain the wrist slight extension. Attach the tubing to the center for the distal portion of the forearm piece.

- Use a small square of thermoplastic material to attach the tubing to the forearm piece.

- Removing the nonstick coating with bonding solvent or marring the top surface with scissors should be done before adhering the pieces.

- One or two straps across the forearm are needed to secure the forearm piece.

Wearing Schedule

- It should be worn when the child is awake, active, and engaged in functional task.

- Inhibitory effect should improve the child’s ability to grasp and release objects, to perform activities requiring bilateral hand use, and to execute isolated finger movement.

- Wearing schedule is influenced by the child’s tolerance, the effects of the splint while on and type of occupations the child engages in during the day

Precautions

- Skin should be inspected for signs of excess pressure.

- FA trough must be securely attached to FA or splint may migrate distally and rub against the radial styloid or distal ulna.

- The length of the tubing should position the wrist in slight extention while also allowing for small gradations of the wrist flexion and extension

- Tubing that is too tight will restrict wrist and finger movement, and tubing that too loose will allow excessive wrist flexion and fail to hold MC bar in place across MC heads

Adaptation

- Thermoplastic thumb trough may be added to the palmar bar to provide support

- Objects such as pipe cleaners may be threaded through the tubing to provide more support and decrease the semi dynamic qualities of the splint

THUMB SPLINTS

- Increased muscle tone frequently pulls the thumb into palmar abduction.

- The purpose of a thumb splint is to improve functional use of the hand by stabilizing the thumb in a functional position of palmar abduction.

- The therapist uses this splint for a child who has some active wrist and finger extension but has difficulty actively moving the thumb out of the palm because of increased tone.

- If tone is moderate to severe, the therapist makes the splint out of thermoplastic material.

- If tone is mild to moderate, the therapist makes the splint from more pliable material, such as neoprene or webbing.

- Thumb splints can be hand or forearm based.

THERMOPLASTIC THUMB SPLINT

Features

- Hand based thumb splint can be of palmar or dorsal design

- The dorsal design results in less bulk in the palm, but the splint may not apply adequate pressure against thenar muscles.

- The palmar design includes metacarpal bar, a thumb trough with a C bar and a hypothenar bar.

- Aside from the inhibitory and facilitory principles of pressure and position, the therapist must remember that the first metacarpal cannot be stabilized unless thermoplastic or another restricting material holds firmly to the adjacent metacarpal.

Process to Fabricate

- The selection of tools and materials are essentially the same for the resting hand splint.

- After cutting out the splint and reheating the material, the therapist places the material on the child’s hand and carefully molds the C bar to nthe humb webspace.

- The hypothenar bar wraps around the ulnar border of the hand far enough to secure the hand, and the metacarpal bar is rolled proximal to the distal creases to allow finger flexion.

- The body of the splint should conform to the palmar arches as they occur during grasp and should extend proximally far enough to adequately position the CMC joint of the thumb but not so far that it interferes with wrist flexion.

- The therapist should assure that the splint does not position the wrist in radial or extreme ulnar deviation.

- The therapist forms the thumb trough by positioning the thumb in palmar abduction and the stretching the plastic to form the C bar.

- The therapist should distribute pressure along the thenar eminence, thus providing optimal positioning of the thumb and avoiding hyperextension of the MP joint.

- The thumb trough should extend just past the IP joint of the thumb but should leave the tip of the thumb free for sensory contact during grasp.

- The finished splint should allow the index and middle fingers to contact the tip of the thumb.

- The therapist should place a strap across the dorsum of the hand.

- If necessary, the therapist should also place a strap across the thumb trough.

- Sometimes during fabrication, it is necessary to modify a small area.

- This can be especially challenging when one is working on a small, curved splint.

- If the therapist wants to use hot water but does not want to risk losing the overall shape, a kitchen baster can be used to draw up hot water and place it repeatedly over the target area.

- Ultratorch is a fine spot heater that allows pinpoint modifications even with 1/16 inch material.

Precautions

- The pressure to position the thumb should be directed below the MP of the thumb to prevent stress and possible dislocation of this joint.

- The splint should also fit snugly into the thumb web space.

- The therapist must watch for signs of skin irritation and pressure.

- The therapist should monitor the child for circulation and nerve compression problems caused by an ill-fitting splint.

Wearing Schedule

- The child should wear the thumb splint during functional activities that require grasp and release.

- The thumb splint can also be worn during the day to prevent the opponens muscle from remaining in a fully shortened position.

- If contractures are a concern, the child may also need to wear a resting hand splint to provide further stretch of the thenar muscles.

- The therapist should give the child opportunities to use the thumb actively, especially after the splint is removed to take advantage of the elongation of the thenar muscles.

- As the child, gains active control of the thumb abduction, the therapist should reduce wearing time of the splint.

SOFT THUMB SPLINT

- Allows more movement of the intrinsic muscles of the hand and active movement of the thumb

- Restricts palmar abduction but does not prevent it entirely

- Available commercially in different sizes from infancy to youth

- Fabrication materials may include webbing and neoprene

- Neoprene thumb splint have an advantage of providing neutral warmth, which may have an inhibitory influence on hypertonicity

- In buying a neoprene thumb splint therapist should consider whether the splint has a Velcro closure

- A thumb splint that slides over the fingers and thumb may be more difficult to apply

- The tone and positioning (TAP) splint is made of neoprene for thumb positioning and forearm supination

- Provides constant low level stretch to the forearm pronators

Adaptations

Web Space Opener

Some children have difficulty maintaining an open thumb web space with a neoprene splint due to moderate to severe hypertonicity. The therapist may make a web space opener out of elastomer to be worn under the thermoplastic splint. Elastomer-silicone based product designed to modify scars, is in liquid and putty form. Once the putty is combined with a catalyst a web space opener can be formed.

Crayon/Marker Attachment

Positioned so tip will contact paper while forearm is in neutral or slight supination(not pronated). A Velcro strap can secure the marker and Sticky Tac or rubber bands above and below to keep the marker from sliding. A separate holder could also be made out of thermoplastic material if necessary (Benik glove).

Fabrication Process for a Soft Thumb Splint with Thumb Loop

- The wrist band and thumb loop are made from a strapping material like webbing or neoprene. The material should be pliable enough to conform to the web space of the thumb

- The therapist can determine the specific dimensions by placing strap material on the child’s arm and hand to measure lengths and widths and determine the desired angle of pull

- Thumb Loop-Strap must be wide enough to support the thumb but not so wide that it buckles or wrinkles in the thumb space

- Wrist Band-Strap should be wide enough to secure the thumb loop,remain in place on the wrist and distribute pressure. It should also be long enough to form an adequate overlap to secure the Velcro.

Pattern

- Wrist band should overlap the volar side of wrist

- Length of the thumb loop should be the distance from the proximal edge of the wrist band, around the thumb and back to the point of origin

Forming the Splint

- Neoprene

- Heat sensitive tape can be used to bond the pieces together

- Sewing may be difficult but can be done with the proper needle, thread and variable tension sewing machines

Webbing

1. Sew hook and loop Velcro to each end of the wrist band that is to overlap on the volar side of the forearm

2. Sew one end of the thumb loop to the dorsal portion of the wrist band, sew loop Velcro to the free end of the thumb loop, then sew hook Velcro to the dorsal portion of the wirst band(partially covering origin of thumb loop)

3. Thumb loop shoud be directed up across the web space, around the thenar eminence and pulled diagonally to attach to the dorsal portion of the wrist band

The amount of tension on the thumb loop and attachment location of the free end on the wrist band influences the amount of radial and palmar abduction of the thumb. If the wrist band does not fit snugly, the splint shifts distally on the wrist, thus reducing the amount of tension on the thumb loop. The wrist band must avoid circulatory restrictions

Precautions and Wearing Schedule

- Similar to thermoplastic splint, although the soft thumb splint presents less danger of pressure related problems due to the softer material.

- Care should be taken so that the wrist band is not so tight that it interferes with circulation.

- Persons applying splint should be sure the thumb loop fits snugly into the web space with pressure against the thenar muscles.

- If thumb loop is applying pressure above the MP joint of thumb, there is a risk of deviating, hyperextending or dislocating.

- Therapist must also monitor the amount of tension on the thumb loop to prevent excess stress to the thumb MP joint.

- If the child is active and wears the splint often, it is likely to be soiled and worn.

- The splint requires washing and eventual replacement.

[pic]

SERPENTINE SPLINT

- By Thompson Rangel

- A hand-based splint

- To position the thumb out of palmar adduction with a little bit inhibitory of finger flexion

- Children with hypertonicity, hypotonicity, muscle weakness, or decreased ROM

Features

1. Easy to make, no significant amount of skill to achieve its fabrication

2. Made of spiral wrap

3. Thermoplastic material opens up the web space and provides good support to the thumb, while allowing for some mobility; allows the child to move the thumb within a specified range

Process to Fabricate

Materials

1. A small rectangular piece of thermoplastic material used; with some stretch to ease making the tube

2. No necessary pattern needed but accurate length of the splint is required

Forming the splint

1. Measure from hypothenar area just below the distal palmar crease across the dorsum of the hand just below the metacarpal joint through the web space around the thenar eminence to the dorsum of the hand

2. Cut a piece of thermoplastic material one half to three fourths the length of the measured length just described and 1 inch in width (width varies among children)

3. Heat the material and roll the piece into a smooth tube

4. Wrap the tube around the hand while it’s still soft, starting at the hypothenar area, below the distal palmar crease, and proceed to wrap as indicated with measuring for the tube (mentioned above)

➢ Straps may be added for extra support

➢ Splint should be labeled to orient the caregiver on how to don the splint

Wearing schedule

- During functional activities for it was designed to facilitate function

- At intervals during the day and night to minimize thumb palmar adduction contractures

Precautions

- Not excessive pressure into the hypothenar area to prevent any skin irritation

Adaptations

- Wrist support is provided by the adaptation of continuation of the spiral tube over the wrist and onto the forearm

- Flat piece of thermoplastic material also allow more molding thus additional stabilization and support of the thumb

Summary

- Several types of hand splint in the management of children who have developmental disabilities as a result of central nervous system damage, lower motor neuron injury, or upper extremity congenital malformations

- Splint designs for a child differ from many of the adult designs cause the types of environments in which they live, learn, work and play differ.

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download