Instructions for Billet Aluminum Air/Oil Separator ...
Instructions for
Billet Aluminum Air/Oil Separator Breather Tank
TFS-51400850, TFS-51400851, TFS-51400852
Thank you for purchasing the universal Trick Flow Billet Aluminum Air/Oil Separator Breather Tank.
The 4oz. capacity tanks feature a modular design that can be used on a variety of applications, including
traditional open breather systems, late model closed systems, and systems for engines equipped with
forced induction. Trick Flow Billet Aluminum Air/Oil Separator Breather Tanks are designed to be used
with Trick Flow oil vapor limiting fittings and plumbing accessories for maximum engine crankcase
ventilation control.
Trick Flow Billet Aluminum Air/Oil Separator Breather Tanks can be used as an Air/Oil Separator or an open
filter breather tank depending on how the unit is incorporated into the PCV or fresh air sides of the engine crankcase
breather system.
Air/Oil Separator Installation
Typically an Air/Oil Separator is used on the PCV side of the engine breather system to reduce the amount of engine oil
vapor entering the intake manifold through the PCV system. In this type of installation it is recommended that Trick Flow oil
vapor limiting fittings with internal strainer be used on the valve cover to plumb the tank into the system, then relocate the
PCV to the top/outlet of the Trick Flow Billet Aluminum Air/Oil Separator Breather Tank.
Breather Tank Installation
Typically a breather tank is used on the fresh air side of an engine breather system and is open to the atmosphere or
plumbed into the system after the MAF sensor on EFI equipped engines. In this type of installation it is recommended that
Trick Flow oil vapor limiting fittings without the filter disc be used on the valve cover to plumb the tank into the system, then
use the open element clamp-on filter adapter TFS-51400870 (available separately), or plumb the top/outlet of the Trick Flow
Billet Aluminum Air/Oil Separator Breather Tank to air intake tube or air filter housing.
Dual Tank Installation
Dual tank installation uses one tank for the PCV side and one tank for the fresh air side of the engine breather system as
described above.
*IMPORTANT NOTE*
Excessive crankcase pressure, or engine oil blowing out the engine breather system could be a symptom of internal
engine damage and should be verified with an engine leak down test prior to installation of air/oil separators or
breather tanks.
Trick Flow Billet Aluminum Air/Oil Separator Breather Tank Accessories (available separately):
Tank and plumbing kits
TFS-K51400850 Universal single tank and plumbing kit for 1 ?¡± hole valve covers
TFS-K51400852 Universal Dual tank and plumbing kit for 1 ?¡± hole valve covers
Individual Components
TFS-51400850 Separator system, 8an inlet single breather/tank, each
TFS-51400851 Separator system, 6an inlet single breather/tank, each
TFS-51400852 Separator system, 8an dual breather/tank, each
TFS-51400853 Separator system plumbing kit, 3 ft. of hose and limiting fittings, single breather/tank, each
TFS-51400854 Separator system plumbing kit, 6 ft. of hose and limiting fittings, dual breather/tank, each
TFS-51400870 2¡± OD Clamp-on filter w/tank adapter, each
Oil Vapor Limiting Fittings (with internal strainer element)
TFS-51400855 Valve cover separator/breather fitting, 1.220" hole,3/4" or 1" breather or PCV valve, push-in, each
TFS-INS-5140085X Rev. 2
6/28/16
PARTS LIST
1
ITEM QTYS.
ITEM
TFS-51400850
TFS-51400851
TFS-51400852
DESCRIPTION
Single Tank
Single Tank
Dual Tank
1
3/4" ID Grommet
1
1
2
2
#10-24 Torx Socket Screw x 3/4 long
6
6
12
Stainless Steel Mounting Bracket Single
1
1
NO.
2
3
Stainless Steel Mounting Bracket Dual
3
4
5
4
7
*Notch side up
4
Top and ID O-rings -223V
2
2
2
5
Machined Aluminum Top Piece
1
1
1
6
Machined Aluminum Can Body
1
1
1
7
1/4npt Lock Nut
1
1
1
8
Fluid Level Sight Plug and Seal
1
1
1
9
Ball Valve O-Ring -205V
1
1
1
10
Ball Valve Drain 1/4npt
1
1
1
11
1/4npt to 3/8" Barb Nipple Fitting
1
1
1
12
Inlet Tube Fitting O-ring -114V
1
1
1
13
6an Breather tube inlet fitting
8an Breather tube inlet fitting
6
1
1
1
1
8 Installation and Assembly
1.
2.
3.
4.
Disconnect negative battery cable on vehicle to prevent potential electrical shock
Find a suitable location to mount the tank and bracket assembly using the (2) holes on the Stainless Steel Bracket
Lubricate all O-rings with clean engine oil for ease of assembly.
Assemble the Trick Flow Billet Aluminum Air/Oil Separator Breather Tank. Start with installing the drain valve
(Item #10) with O-ring and Lock nut. Lock nut is marked with notch indicating the up direction of the tapered thread.
5. Assemble Inlet tube fitting with O-ring into the Can Body .
6. Assemble Top piece onto the Can body, align 5/8¡± dia. round hole on the bottom of the Top piece with the top of the
Inlet tube fitting and properly align the (6) mounting screw holes.
7. Assemble Fluid Level Sight Plug and Seal into the Can Body
8. Install included Grommet into mounting bracket or Clamp-on filter adapter TFS-51400870 (available separately)
9. Install Mounting Bracket O-ring
10. Install Barb fitting for drain
11. Plumb tank into breather system as described earlier in these instructions
12. Check for fluid leaks and/or vacuum
9
13
10
12
11
Ultimate Bolt-On Performance? Lifetime Warranty
Trick Flow Specialties guarantees original, unmodified cylinder head castings against manufacturing defects. Trick Flow¡¯s liability is limited to
replacing the casting.
The valves, valve guides, valve seats, valve job, valve springs, valve spring retainers, valve locks, rocker arm studs, guide plates, and valve stem
seals included on assembled Trick Flow Specialties cylinder heads are warranted to the original purchaser to be free from defects in materials and
workmanship for a period of two years from the date of purchase. All other Trick Flow Specialties products are warranted to be free from defects
in materials and workmanship for a period of 90 days. There are no mileage limitations.
PROPOSITION 65 WARNING
This product may contain one or more substances or chemicals known to the state of California to cause cancer, birth defects or other
reproductive harm.
TRICK FLOW SPECIALTIES
285 WEST AVE.
TALLMADGE, OHIO 44278
(330) 630-1555
TFS-INS-5140085X Rev. 2
6/28/16
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- what do all those things on an ac motor nameplate mean
- us patent no 9 376 945 shop manual m e wagner
- mcsherry auction service ltd box 1135 stonewall mb r0c2z0
- frequently asked questions for dual flow pcv
- proper pcv valve selection for a high performance
- instructions for billet aluminum air oil separator
- president steve fowler
Related searches
- nature medicine instructions for authors
- cane walking instructions for patients
- email instructions for beginners
- scientific reports instructions for authors
- zicam instructions for use
- nature instructions for authors
- yahoo email instructions for beginners
- nature journal instructions for authors
- tablet instructions for dummies
- instructions for schedule d irs
- instructions for schedule a
- nature communications instructions for authors