DALI Power Module SPEC (369650)

HomeWorks

LQSE-2DAL-D

DALI? Power Module (for regions outside of North America)

DALI? Power Module

369650g 1 01.19.22

The DALI? Power Module is a DIN-rail mounted controller for DALI?-compliant digital addressable loads, referred to as control gear. It provides DALI? bus power and control for two independent DALI? buses with up to 64 DALI-compliant digital addressable loads each.

Model Number

LQSE-2DAL-D: 2-link DALI? fixture controller

Features

? Provides power for two buses of DALI?-compliant digital addressable loads:

? 1 28 mA guaranteed current

? 2 50 mA maximum supply current per bus

? Each DALI? bus can control a maximum of 16 zones.

? Power failure memory retains programming in the event of a power loss.

? DALI? Power Module can be used in a HomeWorks system to control and manage light in an entire home or building.

MUX MUX COM

Assembled in Mexico Assembl? aux Mexique Ensamblado en M?xico

Ta > 65 ?C Test | Prueba Tester

LN

HomeWorks QS LQSE-2DAL-D

120 V~ 50/60 Hz 120 mA

230 V~ 50/60 Hz 80 mA



Ta 65 ?C

65/75 ?C Cu Al

NEC? Class 2 IEC PELV

243C IND.CONT.EQ.

5 in-lb (0,6 N?m)

DA 1

DA 2

NEC? Class 2

+1.844.LUTRON1 +44.(0)20.7702.0657

5/16 in (8 mm)

DALI? Power Module (LQSE-2DAL-D)

DALI? Compatibility

The Lutron DALI? Power Module is DALI-2? certified by the Digital Illumination Interface Alliance (DiiA)?. In order to ensure compatibility with Lutron DALI? controllers, the connected DALI? LED drivers and fluorescent ballasts must be DALI-2? certified and marked. In addition to compatibility, it is important to select high-quality and high-performance LED drivers and fluorescent ballasts. DALI-2? certified devices are readily available from many manufacturers and are tested for compatibility with the standard. For a complete list of available DALI-2? certified devices, see the DiiA? website at . DALI? devices that are not listed on the DiiA? website and are not marked DALI-2? cannot be considered DALI-2? certified.

The DALI? version-1 standard does not ensure compatibility. To apply the original DALI? version-1 mark on LED drivers and fluorescent ballasts, no verification of the test results was required, and manufacturers could self-declare compliance and apply the DAL? mark. If you would like to use an LED driver or fluorescent ballast that is not DALI-2? certified but carries a DALI? version-1 logo, Lutron recommends that these devices be tested to ensure compatibility. Lutron is able to perform this testing on request. Samples of the drivers and light engines must be submitted to Lutron and the expected turnaround time is 6 to 8 weeks after the drivers are received. Fees for testing may apply. Lutron recommends that this testing be performed before the fixtures and lighting controls are purchased and installed. Contact your Lutron sales representative for more information.

DALI? bus 1 DALI? bus 2

Control gear

Control gear

Control gear

Control gear

Up to 64 DALI?-

compliant digital addressable loads on each bus

120/230 V~ Control Power

CAL MUX MUX COM

50017652a DIN Rail Power Module LQSE-4A-D

EEA contact address: Lutron EA Limited 125 Finsbury Pavement, 4th floor London EC2A 1NQ United Kingdom (Importer)

IBRA P OIN T

TION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation.

CAN ICES-3 (B)/NMB-3(B)

50 ChinaRohs

Assembled in Mexico Assembl? aux Mexique Ensamblado en M?xico

Ta > 65 ?C Test | Prueba Tester

LN

HomeWorks QS LQSE-2DAL-D

120 V~ 50/60 Hz 120 mA

230 V~ 50/60 Hz 80 mA



Ta 65 ?C

65/75 ?C Cu Al

NEC? Class 2 IEC PELV

243C IND.CONT.EQ.

5 in-lb (0,6 N?m)

DA 1

DA 2

NEC? Class 2

+1.844.LUTRON1 +44.(0)20.7702.0657

5/16 in (8 mm)

HomeWorks Wallstation Power

Module

800 W Max 500 W Max 500 W Max 500 W Max CCI Zone 1 Zone 2 Zone 3 Zone 4

Input Hi Temp Prog Power 230 V~ 50 / 60 Hz 10 A

Option

Def

H

Opt1

M

Opt2

L

Opt3

+44.(0)20.7702.0657

QS Link

HomeWorks Processor

DALI ? Power Module

7 Sivoia QS Shade/Drapery

? SPECIFICATION SUBMITTAL

Job Name:

Model Numbers:

GRAFIK Eye QS

QS Contact Closure Interface

Up to 100 total QS devices

QS Power Supply

Page 1

Job Number:

HomeWorks

LQSE-2DAL-D

DALI? Power Module

Specifications

369650g 2 01.19.22

Power

DALI? Buses

? 120 V~ 50/60 Hz 120 mA ? 230 V~ 50/60 Hz 80 mA

? Up to 64 DALI? compliant loads on each bus can be addressed and grouped into 16 zones.

? Lightning strike protection meets ANSI/IEEE standard ? DALI? Power Module supplies a maximum of 250 mA

62.31-1980. Can withstand voltage surges of up to

to power each bus.

6000 V~ and current surges of up to 3000 A. ? Stand by power: 7 W

? DALI? Power Module supplies a guaranteed current of 128 mA to power each bus.

? BTUs/hour when fully loaded: 24

? DALI? Power Module has an integrated bus power

? DALI? bus Output: 16 V- 128 mA guaranteed supply supply with polarity indicated on the unit.

current, 250 mA maximum supply current per bus.

? Some DALI? loads may be polarity sensitive. Refer

Standards

? Lutron Quality Systems registered to ISO 9001:2015. ? IEC 60669-2-1

to individual manufacturers' specifications for proper connection to the DALI? bus.

? Short circuit protection with automatic restart.

? DALI-2? Certified

QS Link Limits

? UL

? A QS link in a HomeWorks system can have up

? cUL

to 512 zones (outputs) and 100 devices. A DALI?

? NOM

compliant digital addressable load counts as 1 zone

Environment ? Surrounding Air Temperature Range: 0 ?C to 65 ?C

(32 ?F to 149 ?F). ? Relative Humidity: less than 90% non-condensing. ? Calibration point maximum: 75 ?C (167 ?F) ? For indoor use only.

Terminals ? Mains Wiring: 1.0 mm2 to 4.0 mm2

(18 AWG to 10 AWG) ? DALI? bus Wiring: 0.5 mm2 to 4.0 mm2

(20 AWG to 10 AWG)

unless specifically grouped into zones from the Lutron Designer software. ? Each DALI? Power Module counts as one device toward the 100 device limit. ? A maximum of 8 fully loaded DALI? buses may be connected to a single QS link.

HomeWorks Wallstations ? HomeWorks wallstations can be configured to control

DALI? Power Modules with the Lutron Designer software. ? LED indicator displays the status of programmed lights.

? QS Link Wiring: 0.5 mm2 to 4.0 mm2 (20 AWG to 10 AWG)

? Minimum wire temperature rating = 65 ?C (149 ?F),

Troubleshooting and Maintenance Features

copper wire only

? Maintains redundant memory of control gear

Mounting

? Mount in a Lutron DIN Panel (see spec 369788) or in an IP20 (minimum) rated consumer panel or breaker panel with integrated DIN rail.

? Width = 9 DIN modules (161.7 mm or 6 3/8 in). ? For more information on mounting and installation in

panels with integrated DIN rail see Lutron P/N 048466 at

Programming and Compatibility Requirements

programming for ease of single or multiple control gear replacement.

? To verify DALI? lights connected to DALI? bus 1 and bus 2:

? Enter Test Mode: Press and hold Test button on the DALI? Power Module until the Test LED starts flashing.

? Test: Each press of either the DALI? version-1 or DALI-2? button will cycle the lights between high-end, low-end, flash and off for that bus.

? The LQSE-2DAL-D can only be used with a HomeWorks system.

? Exit Test Mode: Press and hold Test button until Test LED stops flashing.

? Setup and programming of the DALI? Power Module is

done through the Lutron Designer software.

? SPECIFICATION SUBMITTAL

Job Name:

Model Numbers:

Job Number:

Page 2

HomeWorks

LQSE-2DAL-D

Overview of Wiring Terminals and Mechanical Dimensions

IEC PELV/NEC? Class 2 QS Link

Z096 N1771

NECR Class 2

DALI? bus 1*

500-13431 Rev. B

DALI? bus 2*

DALI? Power Module

369650g 3 01.19.22

MUX MUX COM

Assembled in Mexico Assembl? aux Mexique Ensamblado en M?xico

Ta > 65 ?C Test | Prueba Tester

LN

HomeWorks QS LQSE-2DAL-D

120 V~ 50/60 Hz 120 mA

230 V~ 50/60 Hz 80 mA



Ta 65 ?C

65/75 ?C Cu Al

NEC? Class 2 IEC PELV

243C IND.CONT.EQ.

5 in-lb (0,6 N?m)

DA 1

DA 2

NEC? Class 2

+1.844.LUTRON1 +44.(0)20.7702.0657

5/16 in (8 mm)

89.7 mm (31/2 in)

Mains Wiring

161.7 mm (63/8 in)

* Wire according to local codes.

60.6 mm (23/8 in)

? SPECIFICATION SUBMITTAL

Job Name:

Model Numbers:

Job Number:

Page 3

HomeWorks

Wiring: Mains Voltage

LQSE-2DAL-D

DALI? Power Module

369650g 4 01.19.22

Wiring from Distribution to Power Module

MUX MUX COM

MUX MUX COM

Assembled in Mexico Assembl? aux Mexique Ensamblado en M?xico

Ta > 65 ?C Test | Prueba Tester

LN

HomeWorks QS LQSE-2DAL-D

120 V~ 50/60 Hz 120 mA

230 V~ 50/60 Hz 80 mA



Ta 65 ?C

65/75 ?C Cu Al

NEC? Class 2 IEC PELV

243C IND.CONT.EQ.

5 in-lb (0,6 N?m)

Assembled in Mexico Assembl? aux Mexique Ensamblado en M?xico

DA 1

DA 2

NEC? Class 2

+1.844.LUTRON1 +44.(0)20.7702.0657

5/16 in (8 mm)

Ta > 65 ?C

Test | Prueba Tester

HomeWorks QS

LQSE-2DAL-D

120 V~ 50/60 Hz 120 mA

230 V~ 50/60 Hz 80 mA



LN

Ta 65 ?C

65/75 ?C Cu Al

? Turn off all circuit breakers or isolators feeding the Power Module unit at the distribution panel.

? Run line, neutral, and earth/ground (D) wires from a feed to the DALI? Power Module.

?NUECs?eCla1s.s02 mm2 to 4.0 mm2 (18 ADWA G1 toD1A22 AWNEGC)? IEcCoPnELdVuctors (depending on breaker rating) tColasfse2ed the mains wiring. The device draws less than 120 mA (120 V~) and 80 mA (230 V~).

Emergency 243C IND.CONT.EQ. Lighting Appl+ic1.a8t4i4o.LnUsTRON1

+44.(0)20.7702.0657

? Use normal (non-essential) power only to power the DALI?5Pino-lwb (e0r,6MN?omd) ule. 5/16 in (8 mm)

? When normal power drops out, the DALI? Power Module will not power the DALI? buses. When this occurs, control gear powered from emergency feeds go to their emergency mode (full light output by default).

Mains Wiring and IEC PELV/NEC? Class 2 Separation

? The DALI? Power Module is designed to separate mains wiring from IEC PELV/NEC? Class 2 circuits.

N

? Follow appropriate local and national codes to avoid

L

violating required separation guidelines.

Distribution Panel

? Earth/Ground N ? Neutral L ? Mains/Line

? SPECIFICATION SUBMITTAL

Job Name:

Model Numbers:

Job Number:

Page 4

HomeWorks

Wiring: DALI Bus

MUX MUX COM

Assembled in Mexico Assembl? aux Mexique Ensamblado en M?xico

Ta > 65 ?C Test | Prueba Tester

LN

HomeWorks QS LQSE-2DAL-D

120 V~ 50/60 Hz 120 mA

230 V~ 50/60 Hz 80 mA



Ta 65 ?C

65/75 ?C Cu Al

NEC? Class 2 IEC PELV

243C IND.CONT.EQ.

5 in-lb (0,6 N?m)

DA 1

DA 2

NEC? Class 2

+1.844.LUTRON1 +44.(0)20.7702.0657

5/16 in (8 mm)

DALI? bus 1 DALI? 1

DALI? 1

DALI? bus 2 DALI? 2

DALI? 2

LQSE-2DAL-D

DALI? Power Module

369650g 5 01.19.22

The DALI? Power Module will supply power for two independent DALI? buses, which supports a maximum of 64 DALI?-compliant digital addressable loads per bus.

DALI? Wiring

? DALI? wiring is not SELV.

? DALI? wiring may be treated as mains voltage, and thus can be run within the same sheathing.

? Ensure that there is no greater than a 2 V ~ drop between the DALI? Power Module and the end of the DALI? bus.

? Consult all national and local electrical codes for separation requirements.

Wire Gauge 1.5 mm2 (14 AWG)

Maximum DALI?-compliant Bus Wire Length

300 m (984 ft)

0.75 mm2 (18 AWG) 150 m (492 ft)

0.5 mm2 (20 AWG) 100 m (328 ft)

DA 1

DA 2

NEC? Class 2

NT.EQ.

b (0,6 N?m)

+1.844.LUTRON1 +44.(0)20.7702.0657

5/16 in (8 mm)

? SPECIFICATION SUBMITTAL

Job Name:

Model Numbers:

Job Number:

Page 5

HomeWorks

Wiring: QS Link

LQSE-2DAL-D

DALI? Power Module

369650g 6 01.19.22

MUX

MUX

COM

Assembled in Mexico Assembl? aux Mexique Ensamblado en M?xico

Ta > 65 ?C Test | Prueba Tester

LN

HomeWorks QS LQSE-2DAL-D

120 V~ 50/60 Hz 120 mA

230 V~ 50/60 Hz 80 mA



Ta 65 ?C

65/75 ?C Cu Al

NEC? Class 2 IEC PELV

243C IND.CONT.EQ.

5 in-lb (0,6 N?m)

DA 1

DA 2

NEC? Class 2

+1.844.LUTRON1 +44.(0)20.7702.0657

5/16 in (8 mm)

meWorks QS

SE-2DAL-D

~ 50 / 60 Hz 120 mA

V~ 50/60 Hz 80 mA



5 ?C

65/75 ?C Cu Al

MUX

MUX

COM

(1) COM N(E2C)? ClaNsso2Connection IE(C3)PMELUVX

(4) MUX

243C IND.CONT.EQ.

5 in-lb (0,6 N?m)

IEC PELV/NEC? Class 2 QS Link Wiring

? Link communicates using IEC PELV/NEC? Class 2 wiring.

? Follow all applicable national and local codes for proper circuit separation and protection.

? Wiring may be daisy chained or t-tapped.

? Do NOT connect terminal 2.

? Total length of QS link must not exceed 610 m (2000 ft).

? Use one, twisted-shielded pair of 0.5 mm2 (20 AWG) for data link (MUX, _).

QS Link Wiring Length Wire Gauge

Available from Lutron in one cable:

Less than 153 m (500 ft)

Power (terminals 1 and 2): 1 pair 1.0 mm2 (18 AWG)

Data (terminals 3 and 4): 1 pair 0.5 mm2 (20 AWG), twisted and shielded

GRX-CBL-346S (non plenum)

GRX-PCBL-346S (plenum)

Power (terminals 1 and 2): GRX-CBL-46L

153 m to

1 pair 4.0 mm2 (10 AWG) (non plenum)

610 m

Data (terminals 3 and 4): GRX-PCBL-46L

(500 to 2000 ft)Dt1Awpis1atierd0.a5nmdDmsAh2ie(22ld0eAdWNG)E, C?(plenum)

Class 2

+1.844.LUTRON1 +44.(0)20.7702.0657

5/16 in (8 mm)

The Lutron Logo, Lutron, HomeWorks, Sivoia, and GRAFIK Eye are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. All other product names, logos, and brands are property of their respective owners.

? SPECIFICATION SUBMITTAL

Job Name:

Model Numbers:

Page 6

Job Number:

 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download