SPIRAL DUCT & FITTINGS - Eastern Sheet Metal
[Pages:20]Eastern Sheet Metal
Single-Wall
ROUND
SPIRAL DUCT & FITTINGS
Eastern Sheet Metal ? 800 348 3440 ?
Rev.#4 7/16
2
Eastern Sheet Metal
Single-Wall
ROUND
SINGLE-WALL ROUND SPIRAL DUCT AND FITTINGS CONSTRUCTION STANDARDS
Positive Pressure
Gauge selection for galvanized steel (ASTM A 653), paint grip steel, type 304 and 316 stainless steel, and Eastern Polyvinyl Chloride Coated Steel (PCS).* Fittings are spot welded and/or gorelocked through 40" diameter. All larger fittings are continuously welded except for PCS fittings. All fittings can be provided as continuously welded if required. All galvanized and PCS spiral duct 6" and larger is corrugated unless ordered without corrugations. Smaller sizes may also be corrugated. Check with the plant when ordering. All spiral duct from other materials will not be corrugated.
DUCT DIAMETER
3"-6" 7"-8" 9"-10" 11"-12" 13"-14" 15"-16" 17"-18" 19"-24" 25"-26" 27"-36" 37"-42" 43"-48" 49"-50" 51"-60" 61"-66" 67"-84"
2005 SMACNA 10" WG SPIRAL DUCT FITTINGS
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
24
24
22
24
22
24
22
22
20
22
20
22
20
22
18
20
18
1995 SMACNA 2" WG SPIRAL DUCT FITTINGS
26
26
26
26
26
26
26
26
26
26
24
24
24
24
24
24
24
24
24
22
22
20
22
20
22
20
20
18
18
16
18
16
1995 SMACNA 10" WG SPIRAL DUCT FITTINGS
26
26
26
26
26
26
26
24
26
24
24
22
24
22
24
22
24
22
22
20
22
20
20
20
20
20
18
18
18
16
18
16
DUCT DIAMETER
3"-8" 9"-14" 15"-26" 27"-36" 37"-50" 51"-60" 61"-84"
1985 SMACNA 2" WG SPIRAL DUCT FITTINGS
26
26
26
26
24
24
24
22
22
20
20
18
18
16
1985 SMACNA 10" WG SPIRAL DUCT FITTINGS
26
24
26
24
24
22
22
20
20
20
18
18
18
16
1975 SMACNA 10" WG SPIRAL DUCT FITTINGS
26
20
26
20
24
20
22
20
20
18
18
18
18
16
Gauge selection for aluminum type 3003. Fittings are spot welded and/or gorelocked through 40" diameter. All larger fittings are continuously welded. All fittings can be provided as continuously welded if required. Brown & Shapre gauge listed in parentheses.
DUCT DIAMETER
2005 SMACNA 2" WG: POSITIVE
SPIRAL
DUCT
FITTINGS
3"-8"
0.025" (22)
0.032" (20)
9"-14"
0.025" (22)
0.032" (20)
15"-26"
0.032" (20)
0.040" (18)
27"-36"
0.040" (18)
0.050" (16)
37"-50"
0.050" (16)
0.063" (14)
51"-60"
0.063" (14)
0.080" (12)
61"-84"
consult
0.090" (11)
factory
2005 SMACNA 2" WG: NEGATIVE
SPIRAL
DUCT
FITTINGS
0.025" (22) 0.032" (20) 0.040" (18) 0.050" (16) 0.063" (14) consult factory consult factory
0.040" (18) 0.040" (18) 0.050" (16) 0.063" (14) 0.080" (12) 0.090" (11)
consult factory
* Because of the limitations of the construction methods we can use, Eastern PCS may require additional sealing in the field.
While the use of this type of material is widespread, ESM urges engineers to always consider the use of stainless steel whenever possible for systems other than underground.
Eastern PCS is not recommended for use in high visibility exposed applications. Please refer to the Eastern PCS Product Guide for more information.
Eastern Sheet Metal ? 800 348 3440 ?
3
Eastern Sheet Metal
Single-Wall
ROUND
SINGLE-WALL ROUND DUCT AND FITTINGS CONSTRUCTION STANDARDS
Negative Pressure
Gauge selection for galvanized steel (ASTM A 653), paint grip steel, type 304 and 316 stainless steel, and Eastern Poly Coated Steel (PCS).* Fittings are spot welded and/or gorelocked through 40" diameter. All larger fittings are continuously welded except for PCS fittings. Check with the plant when ordering. All fittings can be provided as continuously welded if required. All galvanized and PCS spiral duct 6" and larger is corrugated unless ordered without corrugations. Smaller sizes may also be corrugated. All spiral duct from other materials will not be corrugated.
MAX. DUCT DIAM.
6" 8" 10" 12" 14" 16" 18" 20" 22" 24" 30" 36" 42" 48" 54" 60" 66" 72" 78" 84" 90" 96"
2005 SMACNA 2" WG
SPIRAL REIN. &
REIN &
DUCT SPACNG FITTINGS SPACNG
26 26 26 26 26 26 26 A 12 26 A 12 26 A 12 26 A 12 26 A 12 26 A 12 26 A 12 24 A 12 24 B 12 24 B 12 24 B 12 22 B 12 22 C 12 22 C 12 22 D 12 22 E 12
26 26 26 26 24 24 24 A 12 24 A 12 24 A 12 24 A 12 24 A 12 24 A 12 22 A 12 22 A 12 22 B 12 22 B 12 20 B 12 20 B 12 20 C 12 20 C 12 18 D 12 18 E 12
2005 SMACNA 4" WG
SPIRAL REIN. &
REIN. &
DUCT SPACNG FITTINGS SPACNG
26 26 26 26 24 24 26 A 12 26 A 12 26 A 12 26 A 12 24 A 12 24 A 12 22 B 12 22 B 12 22 B 12 22 C 12 20 C 12 20 D 12 20 E 12 20 E 12 18 E 12 18 E 12
26
26
26
24
22
22
24
A 12
24
A 12
24
A 12
24
A 12
22
A 12
22
A 12
20
B 12
20
B 12
18
B 12
18
C 12
18
C 12
18
D 12
18
E 12
18
E 12
16
E 12
16
E 12
2005 SMACNA 6" WG
SPIRAL REIN. &
REIN.&
DUCT SPACNG FITTINGS SPACNG
26 26
26 26
26 24
24 24
24 22
26 A 12
22
26 A 12
22
26 A 12
22
24 A 12
22
24 A 12
22
24 A 12
20
22 B 12
20
22 B 12
18
20 B 12
18
20 C 12
18
20 C 12
18
18 E 12
16
18 E 12
16
18 E 12
16
18 F 12
16
18 G 12
16
18 G 12
16
A 12 A 12 A 12 A 12 A 12 A 12 B 12 B 12 B 12 C 12 C 12 E 12 E 12 E 12 F 12 G 12 G 12
MAX. DUCT DIAM.
6" 8" 10" 12" 14" 16" 18" 20" 22" 24" 30" 36" 42" 48" 54" 60" 66" 72" 78" 84" 90" 96"
2005 SMACNA 10" WG
SPIRAL REIN. &
REIN. &
DUCT SPACNG FITTINGS SPACNG
26 26 26 24 24 A 12 24 A 12 24 A 12 24 A 12 24 A 12 22 A 12 22 A 12 20 B 12 20 B 12 18 C 12 18 D 12 18 E 12 18 E 12 18 F 12 16 G 12 16 G 12 16 G 12 16 G 12
26 24 24 22 22 A 12 22 A 12 22 A 12 22 A 12 20 A 12 20 A 12 18 A 12 18 B 12 18 B 12 16 C 12 16 D 12 16 E 12 16 E 10 16 F 10 16 G 6 16 G 6 16 G 6 16 G 6
1985 SMACNA 2" WG
SPIRAL REIN. &
REIN. &
DUCT SPACNG FITTINGS SPACNG
26 26 26 26 26 24 24 24 24 24 22 22 20 20 18 18 16 16 16 16 NA NA
24 24 24 24 24 22 22 22 22 20 20 20 18 18 16 16 14 14 14 14 NA NA
RIDCSCLASS1 2" WG
SPIRAL REIN. &
REIN.&
DUCT SPACNG FITTINGS SPACNG
22 22 22 22 22 22 20 20 18 18 16 16 20 F1 12 20 F1 12 20 F1 12 18 F1 12 18 F1 12 18 F1 12 18 F1 12 18 F1 12 18 F1 12 18 F1 12
22 22 22 22 22 22 20 F1 20 20 F1 20 20 F1 20 20 F1 20 18 F1 20 16 F1 12 16 F1 12 14 F1 12 14 F1 12 12 F1 12 12 F1 12 12 F1 12 10 F1 12 10 F1 12 10 F1 12 10 F1 12
A,B,C,D,E,F,G = Angle ring reinforcements per SMACNAS 2005 HVAC DCS Table 3-2 F1 = F1 reinforcement per SMACNA RIDCS, Chapter 12 * Refer to note on the bottom of page 2.
Eastern Sheet Metal ? 800 348 3440 ?
4
Eastern Sheet Metal
EASTERN TIGHTTM
EASTERN TIGHT Fittings will save you money by reducing installation time by eliminating joint sealing. They feature a triple-lipped EPDM rubber gasket, held in place with a 180? hemmed edge, that provides a reliable, airtight seal. EASTERN TIGHT Fittings are suitable for use for temperatures ranging from -20? F to 212? F. When tested in accordance with ASTM E84, EASTERN TIGHT Fittings have flame-spread and smokedeveloped ratings of 0/0.
Full-bodied fittings, couplings, reducers, elbows, and taps are available with EASTERN TIGHT in even and odd sizes from 3" through 10" in diameter, and even sizes up to 36" in diameter. Fittings are secured to the duct with selftapping screws uniformly located around the circumference per SMACNA standards.
EASTERN TIGHT Fittings are available in singlewall construction, fabricated from galvanized or paint grip. EASTERN TIGHT Fittings have been independently tested and can be used to meet SMACNA Class 3 leakage standards for -2" WG to +10" WG.
Before Installation 3"-24" diameter After Installation
Before Installation 26"-36" diameter After Installation
EASTERN TIGHT ROUND SPIRAL DUCT AND FITTINGS CONSTRUCTION STANDARDS Gauge selection for galvanized steel (ASTM A653) or paint grip. Fittings are assembled with stitch welds, spot welds, or standing seams and are sealed. All galvanized spiral duct 6" and larger is corrugated unless ordered without corrugation. Smaller sizes may also be corrugated. Check with the plant when ordering. All spiral duct from other materials will be smooth.
DUCT DIAMETER
3"-6" 7"-18" 9"-10" 11"-12" 13"-14" 15"-16" 17"-18" 19"-20" 21"-22" 23"-24" 25"-30" 31"-36"
2005 SMACNA 10" WG POSITIVE
SPIRAL
DUCT
FITTINGS
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
24
26
24
26
24
24
22
24
22
2005 SMACNA 2" WG NEGATIVE
SPIRAL
DUCT
FITTINGS
26
26
26
26
26
26
26
26
26
24
26
24
26R
24R
26R
24R
26R
24R
26R
24R
26R
24R
26R
24R
R = Reinforcement ring at 12' maximum spacing. Individual fittings may not have reinforcement.
EASTERN TIGHT Fittings have been tested in our standard gauges for -2" to +10" WG and have been used to meet SMACNA Class 3 leakage standards.
EASTERN TIGHT Fittings and Couplings are covered by one or more of the following U.S. Patents: D437,034; D435,090; D430,482; D427,673; D427,668; D427,667; D553,238; D551,336; 7287407; D518,885; D517,679; D516,698; D516,697. Other patents pending.
For more information, refer to Eastern Sheet Metal's EASTERN TIGHT Product Guide.
Eastern Sheet Metal ? 800 348 3440 ?
Eastern Sheet Metal
5
Single-Wall Round
CONSTRUCTION
SPIRAL DUCT LOCK SEAM (RL --1)
LOCKSEAM
(2) CORRUGATIONS BETWEEN SEAMS (GALV AND POLYVINYL CHLORIDE COATED
LOCKSEAM
SPIRAL DUCT CORRUGATED (RL--1)
SEALER
LAP SEAM spot weld seam weld stitch weld button punch
rivet
BUTT-WELDED SEAM
SEALER GORELOCKED SEAM
GALVANIZED STAINLESS STEEL ALUMINUM PAINT GRIP POLYVINYL CHLORIDE COATED PERFORATED
Available Gauges
28-14 26-18 22-14* 26-16 26-18 22
*(Brown & Sharp thickness = 0.025" - 0.090")
GALVANIZED STAINLESS STEEL ALUMINUM PAINT GRIP POLYVINYL CHLORIDE COATED
Available Gauges
26-18 26-18 22-18* 26-18 26-18
*(Brown & Sharp thickness = 0.025" - 0.090")
GALVANIZED STAINLESS STEEL ALUMINUM PAINT GRIP HOT ROLLED
Available Gauges
20-10 22-10 16-1/4"* 20-16 16-1/4"
*(Brown & Sharp thickness = 0.05" - 0.25")
GALVANIZED STAINLESS STEEL ALUMINUM PAINT GRIP POLYVINYL CHLORIDE COATED
Available Gauges
26-18 26-22 22-16 26-18 26-18
*(Brown & Sharp thickness = 0.025" - 0.050")
Eastern Sheet Metal ? 800 348 3440 ?
6
Eastern Sheet Metal
Single-Wall Round
ELBOWS
90? PRESSED ELBOW
3" DIA. THRU 12"
PE90
D1
45? PRESSED ELBOW
3" DIA. THRU 12"
PE45
D1
R=D1 2"
R= D1 2"
90? 5-PC.ELBOW
E90
45? 3-PC. ELBOW
E45
D1
D1
R=D1 2"
60? 3-PC. ELBOW
E60
D1
R=D1 2"
R=D1 2"
221/2? AND 30? 2-PC. ELBOW E22/E30 D1
R=D1 2"
Eastern Sheet Metal ? 800 348 3440 ?
Eastern Sheet Metal
90? 3-PC. ELBOW WITH
HEEL TAP
E90L
D2 2"
4"
2" D1
R=D1
7
Single-Wall Round
ELBOWS
90? 2-PC. ELBOW E290/EV290
D1 No. of Vanes
3-7 8-10 10-60 > 60
1 3 5 max spacing =12"
2"
With or without vanes.
D1 2"
Eastern Sheet Metal ? 800 348 3440 ?
8
Eastern Sheet Metal
FIELD INSTALLED PRESSED
TAP
PFT
D3 R
11/2"
D1
PRESSED TEE
PT
R D1
D3 11/2"
L
Single-Wall Round
PRESSED TEES
D3/D1 4"/4" 4"/6" 4"/8" 4"/10" 4"/12" 6"/6" 6"/8" 6"/10" 6"/12" 6"/14" 6"/16" 6"/18" 8"/8" 8"/10" 8"/12" 8"/14" 8"/16" 8"/18" 8"/20" 8"/22" 8"/24" 10"/10" 10"/12" 10"/14" 10"/16" 10"/18" 10"/20" 10"/22" 10"/24" 12"/12" 12"/14" 12"/16" 12"/18" 12"/20" 12"/22" 12"/24"
R .394" .394" .394" .394" .394" .787" .787" .787" .787" .787" .787" .787" .787" .787" .787" .787" .787" .787" .787" .787" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0" 1.0"
L (PT) 14" 14" 14" 14" 14" 16" 16" 16" 16" 16" 16" 16" 18" 18" 18" 18" 18" 18" 18" 18" 20" 20" 20" 20" 20" 20" 20" 20" 20" 22" 22" 22" 22" 22" 22" 22"
Eastern Sheet Metal ? 800 348 3440 ?
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- spiral duct and fittings construction standards
- spiral duct specifications
- specifications for spiral pipe and fittings
- gauge and weight chart for sheet steel
- duct fabrication specifications duct construction
- spiral duct fittings eastern sheet metal
- sheet metal catalog
- item 680 92020404 conduit galvanized steel
- item 680 92020404 conduit galvanized steel multi
Related searches
- sheet metal bending calculator
- sheet metal layout formulas
- sheet metal flat pattern calculator
- sheet metal pattern layout
- sheet metal bending calculator free
- sheet metal pattern layout methods
- free sheet metal layout patterns
- sheet metal layout drawings
- sheet metal bender hand tool
- sheet metal bending formula
- practical sheet metal layout pdf
- sheet metal bending calculation formula