ADG1408/ADG1409 (Rev. D) - Analog Devices
Data Sheet
4 RON, 4-/8-Channel, ?15 V/+12 V/?5 V iCMOS Multiplexers
ADG1408/ADG1409
FEATURES
4.7 maximum on resistance at 25?C 0.5 on-resistance flatness Up to 190 mA continuous current Fully specified at ?15 V/+12 V/?5 V 3 V logic-compatible inputs Rail-to-rail operation Break-before-make switching action 16-lead TSSOP and 4 mm ? 4 mm LFCSP
APPLICATIONS
Relay replacement Audio and video routing Automatic test equipment Data acquisition systems Temperature measurement systems Avionics Battery-powered systems Communication systems Medical equipment
GENERAL DESCRIPTION
The ADG1408/ADG1409 are monolithic iCMOS? analog multiplexers comprising eight single channels and four differential channels, respectively. The ADG1408 switches one of eight inputs to a common output, as determined by the 3-bit binary address lines, A0, A1, and A2. The ADG1409 switches one of four differential inputs to a common differential output, as determined by the 2-bit binary address lines, A0 and A1. An EN input on both devices is used to enable or disable the device. When disabled, all channels are switched off.
The industrial CMOS (iCMOS) modular manufacturing process combines high voltage complementary metal-oxide semiconductor (CMOS) and bipolar technologies. It enables the development of a wide range of high performance analog ICs capable of 33 V operation in a footprint that no other generation of high voltage devices has been able to achieve. Unlike analog ICs using conventional CMOS processes, iCMOS components can tolerate high supply voltages while providing increased performance, dramatically lower power consumption, and reduced package size.
FUNCTIONAL BLOCK DIAGRAMS
ADG1408
ADG1409
S1
S1A
DA
S4A
D
S1B DB
S8
S4B
1-OF-8 DECODER
1-OF-4 DECODER
A0 A1 A2 EN
A0 A1 EN
Figure 1.
04861-001
The ultralow on resistance and on resistance flatness of these switches make them ideal solutions for data acquisition and gain switching applications where low distortion is critical. iCMOS construction ensures ultralow power dissipation, making the devices ideally suited for portable and batterypowered instruments.
PRODUCT HIGHLIGHTS
1. 4 on resistance. 2. 0.5 on-resistance flatness. 3. 3 V logic compatible digital input, VIH = 2.0 V, VIL = 0.8 V. 4. 16-lead TSSOP and 4 mm ? 4 mm LFCSP.
Table 1. Related Devices
Device No.
Description
ADG1208/ADG1209
Low capacitance, low charge injection, and low leakage 4-/8-channel ?15 V multiplexers
Rev. D
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ?2006?2016 Analog Devices, Inc. All rights reserved.
Technical Support
ADG1408/ADG1409
TABLE OF CONTENTS
Features .............................................................................................. 1 Applications....................................................................................... 1 Functional Block Diagrams............................................................. 1 General Description ......................................................................... 1 Product Highlights ........................................................................... 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3
15 V Dual Supply.......................................................................... 3 12 V Single Supply........................................................................ 5 5 V Dual Supply ............................................................................ 7
REVISION HISTORY
6/2016--Rev. C to Rev. D Changes to Analog Inputs Parameter, Table 6 .............................. 9 Added Digital Inputs Parameter, Table 6 ...................................... 9
5/2016--Rev. B to Rev. C Changed CP-16-13 to CP-16-26 .................................. Throughout Changes to Figure 3 ........................................................................ 10 Changes to Figure 5 ........................................................................ 11 Updated Outline Dimensions ....................................................... 19 Changes to Ordering Guide .......................................................... 20
3/2009--Rev. A to Rev. B Change to IDD Parameter, Table 2 ................................................... 4 Change to IDD Parameter, Table 3 ................................................... 6
8/2008--Rev. 0 to Rev. A Changes to Features.......................................................................... 1 Added Table 5; Renumbered Sequentially .................................... 8 Changes to Table 6............................................................................ 9 Added Exposed Pad Notation to Figure 3................................... 10 Added Exposed Pad Notation to Figure 5................................... 11 Added Exposed Pad Notation to Outline Dimensions ............. 19
8/2006--Revision 0: Initial Version
Data Sheet
Continuous Current per channel, S or D ...................................8 Absolute Maximum Ratings ............................................................9
Thermal Resistance .......................................................................9 ESD Caution...................................................................................9 Pin Configurations and Function Descriptions ......................... 10 Typical Performance Characteristics ........................................... 12 Terminology .................................................................................... 16 Test Circuits..................................................................................... 17 Outline Dimensions ....................................................................... 19 Ordering Guide .......................................................................... 19
Rev. D | Page 2 of 19
Data Sheet
ADG1408/ADG1409
SPECIFICATIONS
15 V DUAL SUPPLY
VDD = +15 V ? 10%, VSS = -15 V ? 10%, GND = 0 V, unless otherwise noted.
Table 2.
Parameter ANALOG SWITCH
Analog Signal Range On Resistance (RON)
On Resistance Match Between Channels (RON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS Source Off Leakage, IS (Off )
Drain Off Leakage, ID (Off )
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current
+25?C
4 4.7 0.2
0.78 0.5 0.72
?0.04 ?0.2 ?0.04 ?0.45 ?0.1 ?1.5
?0.005
Digital Input Capacitance, CIN
4
DYNAMIC CHARACTERISTICS2
Transition Time, tTRANSITION
140
170
Break-Before-Make Time Delay, tBBM 50
tON (EN)
tOFF (EN)
Charge Injection Off Isolation Channel-to-Channel Crosstalk Total Harmonic Distortion Plus
Noise (THD + N) -3 dB Bandwidth
ADG1408 ADG1409 Insertion Loss CS (Off ) CD (Off ) ADG1408 ADG1409
100 120 100 120 -50 -70 -70 0.025
60 115 0.24 14
80 40
-40?C to -40?C to
+85?C
+125?C1
VSS to VDD
5.7
6.7
0.85
1.1
0.77
0.92
?0.6
?5
?2
?30
?3
?30
2.0 0.8
?0.1
210
240
30
150
165
150
170
Unit
V typ max typ
max typ max
nA typ nA max nA typ nA max nA typ nA max
V min V max A typ A max pF typ
ns typ ns max ns typ ns min ns typ ns max ns typ ns max pC typ dB typ dB typ % typ
MHz typ MHz typ dB typ pF typ
pF typ pF typ
Test Conditions/Comments
VS = ?10 V, IS = -10 mA; see Figure 26 VDD = +13.5 V, VSS = -13.5 V VS = ?10 V, IS = -10 mA
VS = ?10 V, IS = -10 mA
VDD = +16.5 V, VSS = -16.5 V VS = ?10 V, VD = 10 V; see Figure 27
VS = ?10 V, VD = 10 V; see Figure 27
VS = VD = ?10 V; see Figure 28
VIN = VGND or VDD
RL = 100 , CL = 35 pF VS = 10 V, see Figure 29 RL = 100 , CL = 35 pF VS1 = VS2 = 10 V; see Figure 30 RL = 100 , CL = 35 pF VS = 10 V; see Figure 31 RL = 100 , CL = 35 pF VS = 10 V; see Figure 31 VS = 0 V, RS = 0 , CL = 1 nF; see Figure 32 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 33 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 34 RL = 110 , 15 V p-p, f = 20 Hz to 20 kHz; see Figure 36 RL = 50 , CL = 5 pF; see Figure 35
RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 35 f = 1 MHz f = 1 MHz
Rev. D | Page 3 of 19
ADG1408/ADG1409
Data Sheet
Parameter CD, CS (On) ADG1408 ADG1409
POWER REQUIREMENTS IDD
+25?C
135 90
0.002
220
ISS
0.002
VDD/VSS
1 Temperature range: Y version: -40?C to +125?C. 2 Guaranteed by design, not subject to production test.
-40?C to +85?C
-40?C to +125?C1 Unit
pF typ pF typ
1
380
1 ?4.5/?16.5
A typ A max A typ A max A typ A max V min/max
Test Conditions/Comments f = 1 MHz
VDD = +16.5 V, VSS = -16.5 V Digital inputs = 0 V or VDD Digital inputs = 5 V Digital inputs = 0 V, 5 V or VDD
Rev. D | Page 4 of 19
Data Sheet
ADG1408/ADG1409
12 V SINGLE SUPPLY
VDD = 12 V ? 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 3.
Parameter ANALOG SWITCH
Analog Signal Range On Resistance (RON)
On-Resistance Match Between Channels (RON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS Source Off Leakage, IS (Off )
Drain Off Leakage, ID (Off )
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current
-40?C to +25?C +85?C
6
8
9.5
0.2
0.82 0.85
1.5
2.5
2.5
?0.04 ?0.2 ?0.6 ?0.04 ?0.45 ?1 ?0.06 ?0.44 ?1.3
?0.005
Digital Input Capacitance, CIN
5
DYNAMIC CHARACTERISTICS2
Transition Time, tTRANSITION
200
260 330
Break-Before-Make Time Delay, tBBM 90
tON (EN)
tOFF (EN)
Charge Injection Off Isolation Channel-to-Channel Crosstalk -3 dB Bandwidth
ADG1408 ADG1409 Insertion Loss CS (Off ) CD (Off ) ADG1408 ADG1409 CD, CS (On) ADG1408 ADG1409
160 210 250 115 145 180 -12 -70 -70
36 72 0.5 25
165 80
200 120
-40?C to +125?C1 0 to VDD 11.2
1.1 2.8
?5 ?37 ?32 2.0 0.8 ?0.1
380 40 285 200
Unit
V typ max typ
max typ max
nA typ nA max nA typ nA max nA typ nA max
V min V max A typ A max pF typ
ns typ ns max ns typ ns min ns typ ns max ns typ ns max pC typ dB typ dB typ
MHz typ MHz typ dB typ pF typ
pF typ pF typ
pF typ pF typ
Test Conditions/Comments
VS = 0 V to 10 V, IS = -10 mA; see Figure 26 VDD = 10.8 V, VSS = 0 V VS = 0 V to 10 V, IS = -10 mA
VS = 0 V to 10 V, IS = -10 mA
VDD = 13.2 V VS = 1 V/10 V, VD = 10 V/1 V; see Figure 27
VS = 1 V/10 V, VD = 10 V/1 V; see Figure 27
VS = VD = 1 V or 10 V; see Figure 28
VIN = VGND or VDD
RL = 100 , CL = 35 pF VS = 8 V; see Figure 29 RL = 100 , CL = 35 pF VS1 = VS2 = 8 V; see Figure 30 RL = 100 , CL = 35 pF VS = 8 V; see Figure 31 RL = 100 , CL = 35 pF VS = 8 V; see Figure 31 VS = 6 V, RS = 0 , CL = 1 nF; see Figure 32 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 33 RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 34 RL = 50 , CL = 5 pF; see Figure 35
RL = 50 , CL = 5 pF, f = 1 MHz; see Figure 35 f = 1 MHz f = 1 MHz
f = 1 MHz
Rev. D | Page 5 of 19
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- design of analog cmos integrated circuits
- windows 10 desktop analog clock
- analog clock windows 10 desktop
- design of analog cmos integrated circuits 2nd
- analog integrated circuit design pdf
- razavi analog cmos pdf
- analog circuit design pdf
- cmos analog circuit design pdf
- analog clock display on desktop windows 10
- ept analog pregnancy test sensitivity
- analog clock app for windows 10 desktop
- analog clock for windows 10