2011 MDX - - Passenger's Dashboard Trim Removal/Installation



2011 MDX - - Passenger's Dashboard Trim Removal/InstallationSpecial Tools RequiredKTC Trim Tool Set SOJATP2014*Available through the Acura Tool and Equipment Program, 888-424-6857NOTE:Take care not to scratch the dashboard or the related parts.Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.Open the front door, and remove the passenger's dashboard side cover (A).Pull out the front door opening seal (B), as needed.Gently pull out the front edge of the side cover, and pry the rear edge with a trim tool to release the hooks (C), then remove the side cover.Open the glove box.Remove the passenger's dashboard trim (A).Remove the screw.Gently pull out the lower edge and the outside edge of the trim by hand to detach all of the clips and the hooks (B).Install the trim in the reverse order of removal, and note these items:If the clips are damaged or stress-whitened, replace them with new ones.Position the hooks first on installation, then move the clips into place.Push the clips and the hooks into place securely.Portions of materials contained herein are sourced from American Honda Motor Inc., Co. Copyright 2009 - 2013 Service Repair Solutions, Inc. 2011 MDX - - Driver's Inner Dashboard Trim Removal/InstallationSpecial Tools RequiredKTC Trim Tool Set SOJATP2014*Available through the Acura Tool and Equipment Program, 888-424-6857NOTE:Take care not to scratch the dashboard or the related parts.Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.Remove the driver's inner dashboard trim (A).Gently pull out along the edge beside the audio unit by hand to release the lower hooks (B) and the clip (C).Detach the upper clips (D).Install the trim in the reverse order of removal, and note these items:If the clips are damaged or stress-whitened, replace them with new ones.Position the hooks first on installation, then move the clips into place.Push the clips and the hooks into place securely.Portions of materials contained herein are sourced from American Honda Motor Inc., Co. Copyright 2009 - 2013 Service Repair Solutions, Inc. 2011 MDX - - Navigation Display Unit Removal/InstallationNOTE:Put on gloves to protect your hands.Take care not to scratch the dashboard and related parts.Lay a shop towel under the parts when working on them to protect the face panel from scratches or other damage.When prying components, use the KTC trim tool or equivalent.Remove the dashboard center upper panel.Remove the screws (A) and bolt (B), then remove the display unit (C).Disconnect the navigation display unit connector (D), and detach the clip (E).Install the unit in the reverse order of removal. Be careful not to drop the forward bolt behind the dashboard.Portions of materials contained herein are sourced from American Honda Motor Inc., Co. Copyright 2009 - 2013 Service Repair Solutions, Inc. 2011 MDX - - Audio-Navigation Unit Removal/InstallationSRS components are located in this area. Review the SRS component locations, and the precautions and procedures?? before doing repairs or service.NOTE:Put on gloves to protect your hands.Take care not to scratch the dashboard and related parts.Lay a workshop towel under the parts when working on them to protect the face panel from scratches or other damage.Eject all the discs before remove the audio-navigation unit to prevent damaging the CD player's load mechanism.If you are replacing the audio-navigation unit, write down the audio presets (if possible), and enter them into the new audio-navigation unit.Make sure you have the anti-theft codes for the audio-navigation unit. HYPERLINK "" Remove the driver's inner dashboard trim, and the passenger's dashboard trim.Remove the console lower trim (A) and the bolts (B), then pull out the audio-navigation unit (C).Disconnect the connectors (D), then remove the audio-navigation unit.Remove the climate control unit.Remove the bolts (A) and the radio brackets (B).Remove the screws and audio-navigation unit (C) from the audio-navigation panel (D).Remove the interface dial.If you are replacing the audio-navigation unit, remove the HDD from the original audio-navigation unit, and install it in the replacement audio-navigation unit.NOTE: To avoid damaging the audio-navigation unit or HDD:Do not remove the HDD with any of the audio-navigation unit connectors connected.Do not power up the audio-navigation unit without the HDD installed.Install the audio-navigation unit in the reverse order of removal.NOTE: Check any official Honda service website for more service information about patches for the navigation system. Apply any prescribed patches to the new audio-navigation unit.Enter the new audio-navigation unit anti-theft codes.Park the vehicle outside, and do the GPS initialization.Give the new anti-theft codes to the client.Portions of materials contained herein are sourced from American Honda Motor Inc., Co. Copyright 2009 - 2013 Service Repair Solutions, Inc. 2011 MDX - - GPS Antenna Removal/InstallationNOTE:Put on gloves to protect your hands.Take care not to scratch the dashboard and related parts.Lay a shop towel under the parts when working on them to protect the face panel from scratches or other damage.Remove the audio-navigation unit.Remove the navigation display unit.Remove the screws (A), and detach the clips (B), then remove the GPS antenna (C).Install the antenna in the reverse order of removal.Portions of materials contained herein are sourced from American Honda Motor Inc., Co. Copyright 2009 - 2013 Service Repair Solutions, Inc. ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download