Kristen - About



Table of ContentsIntroduction 1Review of Literature4Problem Statement10Experimental Design11Data and Observations16Data Analysis and Interpretation21Conclusion33Works Cited39IntroductionSoccer is a common pastime throughout the world, and possibly the world’s most popular sport. The 2010 FIFA World Cup in South Africa in-home television coverage reached 3.2 billion people (FIFA). Though many argue over when the sport originated, the most widely accepted idea of its origin is in China in 300 B.C. The Chinese called the game "Tsu Chu," which involved using no hands to place a leather ball in a small hole (Blain). The game has now evolved to the sport it is today, played with the approved ball type of the International Federation of Association Football (FIFA), made out of synthetic leather at standard sizes consisting of a cover, lining, stitching, and bladder, which is the inside of the ball that holds the air in (Monet). Now, a soccer ball may seem like any average ball, but many factors contribute to its performance. Some of these factors include the ball’s diameter, air pressure, and the surface the balls roll on. Knowledge of how a soccer ball travels on the ground is crucial to a quality soccer game, for much of the ball’s traveling is done on the ground, as players dribble the ball across the soccer field. The experiment that was performed tested how these important factors affected the distance a soccer ball travels when rolled from a ramp.In the experiment that was conducted, different types of soccer balls were used. The soccer balls used were size 3, size 4, and size 5, with diameters 7 inches, 8 inches, and 9 inches, respectively (Parrish). These sizes are representative of the standard sizes of soccer balls that are most commonly used, with smaller soccer balls being for young kids, and the larger soccer balls used in adult or professional soccer games. The recommended air pressure of a soccer ball ranges from 6 psi to 12 psi (Parrish). The air pressure values of 6 psi, 9 psi, and 12 psi, were determined by using the high, low, and middle value of the standard air pressure range of a soccer ball. The third factor in the experiment was ground surface. Different surfaces cause different amounts of friction between the soccer ball and ground surface. Because soccer balls and other balls often roll on different surfaces, depending on where the game is being played, whether it is in the streets, on the grass, or any other location such as artificial turf, it is important to be aware of how the ball will perform on the different surfaces. The surfaces of grass, dirt, and asphalt were chosen to test the effect different coefficients have on the performance of soccer balls. Different air pressures were used to determine how inflating the ball more would change the distance, and different sizes were used to see how different size soccer balls would travel. During the experiment, high and low levels of air pressure, diameter, and ground surface were tested as the ball rolled down a wooden ramp. The distance from the end of the ramp to the stopping point of the ball was measured and analyzed so that the effects of the three factors could be determined and then applied to the performance of a soccer ball.The results from this experiment have many applications to various types of people. First and foremost, the results can be used to improve the performance of soccer players. A greater knowledge of how ground surface, air pressure, and diameter affect the distance a soccer ball travels can help a soccer player better prepare his ball for a game, better judge the distance that ball will travel as he is playing, and better transition from surface to surface when playing in different places. For example, when he is playing on a grass surface, a soccer player will know that he needs to account for a greater amount of friction in order to achieve the necessary distance when dribbling the soccer ball. With an increased awareness on soccer ball, the quality of players and the game itself will increase. This knowledge can extend far past just the world of soccer into the world of other sports that use balls, such as baseball. Although air pressure does not apply, diameter and ground surface are important to baseball. Differences in diameter would apply to softballs versus baseballs, and ground surfaces changes as a ball rolls from the infield to the outfield. The results of this experiment can improve the quality of baseball players. From a business standpoint, it is important to make products that are as high-quality performing as possible.Knowledge of the effects of ground surface, air pressure, and diameter can allow manufacturers to create products that are best prepared for the different conditions balls, or any other rolling product such as tires, may be exposed to outside. They may even be inspired to research other factors that may affect the performance of balls as well such as ball material. Whether people are athletes, sports fans, businessmen, or just interested in science, the results of this experiment can be applied to their lives.Review of LiteratureThe experiment conducted included a wide range of scientific topics and applications. These topics and many previous experiments were examined in order to determine the hypothesis of this experiment. The main topics that were investigated were size of a soccer ball, air pressure of a soccer ball, and friction of the ground surface on which the ball rolls.One of the factors in the experiment was the air pressure of the soccer ball. Air pressure is the force exerted by air on any surface in contact with it (Benson). In this case, the air inside the soccer ball exerts a force on the surface of the soccer ball. If there is more air and therefore more pressure, the ball will be harder and more solid. The higher the pressure inside the ball, the farther the ball should roll (Gibbs). If the ball has a higher psi (pounds per square inch), and therefore more pressure, the soccer ball will have a smaller contact area with the ground because it is inflated more and will flatten out less when coming in contact with a surface. The laws of friction state that the area of contact between the ball and the ground does not affect the friction between the surfaces, but it will affect how far the ball travels. This law of friction changes when the surface areas are small, because the coefficient of friction increases since the object may sink into the surface somewhat (Nave). The ball has a very small contact area with the ground, so the coefficient increases and the ball does not go as far. Think of a ball that has been almost completely deflated. The ball will not roll far because the bottom of the ball is flat and it must “roll over itself.” This can also be seen in a rolling tire. The more a tire is inflated, the better it is able to roll (Barry). When the ball has a higher psi, it should travel farther because it would be easier for it to roll over the surface.One part of this experiment was determining what effect the diameter of the ball would have on the distance traveled. The moment of inertia of an object defines its resistance to a change in angular motion (Nave). The moment of inertia of a soccer ball, measured in kg × m2, is found using the formula for the moment of inertia of a hollow sphere I = ?mr2 where moment of inertia, I, is equal to 2/3 times the mass of the ball, m, times the radius of the ball, r, squared (McWeeny 66). I = ?mr2 A smaller moment of inertia means that the ball would have a lower resistance to a change in rotational motion, so it would rotate easier (Robertson). The less mass and smaller radius a ball has, the less momentum it has. Momentum is defined as the quantity of motion of a moving body. A smaller moment of inertia and less momentum also means that an object will slow down easier. Lower resistance to a change in motion works both ways, meaning that it is both easier to start something in motion and slow it down. The smallest diameter soccer ball would have the smallest moment of inertia because it has the smallest radius and also a smaller mass than the other two. Because it is able to rotate more easily, it will have a higher velocity than the larger soccer balls, and therefore travel farther because of it going at a faster speed.Ground surface was another factor in the conducted experiment. The ball would roll farther on a surface with less friction. The type of friction that is primarily shown in this experiment is rolling friction. Rolling friction works in largely the same way as kinetic friction except the object is not just sliding forward, it is rolling. This is shown in Figure 1 below. A force acts on the rolling object, causing it to roll and move forward. The force of friction that comes from the ground opposes this motion, acting in the opposite direction, forcing it to slow down.Figure 1. Rolling Friction Diagram (Piccolo)The surfaces from the lowest coefficient of friction to the highest are asphalt, dirt (such as on a baseball diamond), and grass. Coefficient of friction is the frictional force that resists the motion of an object. A higher coefficient of kinetic friction between two objects means that the surface resists motion more (Schlager). Newton’s first law states that an object in motion remains in motion until acted upon by an unbalanced force, such as friction (“Newton’s First Law”). The grass would act on the ball with the greatest frictional force, because it has the highest coefficient, stopping it in the shortest distance. The distance traveled by the soccer ball can also be determined by looking at how hard surfaces, such as asphalt, and softer surfaces, such as grass, act on a hard or soft object. The combination that would result in the farthest distance traveled is a hard object on a hard surface (Kurtus). When a ball is rolling on grass, or when any object is sliding on grass, there is more work being done. The ball must work to bend the grass down to move over it and it could also get pushed slightly into the dirt below it. With asphalt, this is not the case. It is a flat surface with nothing on it, so the ball can move over it easier. In the current experiment, the hardest object is the most inflated ball and the hardest surface is asphalt, so the ball is likely to travel the farthest under these circumstances.An experiment related to the one conducted is an experiment performed by Yusaka Tsuji and Yoshitsugu Muguruma in the Department of Mechanical Engineering at Osaka University in Japan. The experiment tested the effect of ball diameter on the motion of table tennis balls. The balls being tested, with diameters of 38 mm, 39 mm, and 40 mm to represent standard table tennis ball sizes, were placed at a uniform point on a table tennis table, and then set off at a constant initial velocity and angle. Then, the velocity of the balls was measured at key points along the table, including before the first bounce and directly after the first bounce of the balls (Tsuji and Muguruma 42). After all the trials, it was concluded that an increase in ball size lead to a decrease in the ball’s velocity at the measured points along the table (Tsuji and Muguruma 53). This experiment relates to the conducted experiment because diameter is a factor in both experiments, and both involve the motion of balls. However, in the table tennis balls experiment, velocity was measured after air travel, while in the soccer balls experiment that was conducted, distance was measured after rolling on the ground. Nonetheless, it was inferred that a velocity decrease in a ball travelling through the air would lead to a velocity decrease rolling on the ground. A velocity decrease would result in a decrease in the distance traveled by the ball, supporting the experiment’s hypothesis that the low ball diameter of 7 inches would result in the greatest distance traveled by the soccer ball on the ground.An experiment was done relating to moment of inertia by Hans J. Kolitzus from the International Association for Sports Surface Sciences (ISSS). The experimenter rolled a ball from a ramp onto a surface and determined moment of inertia from that. The moment of inertia from this experiment can be used for the soccer ball experiment. Both experiments use the moment of inertia for a hollow sphere. The experiment helps determine the hypothesis for the conducted soccer ball experiment because it shows that the smaller moment of inertia of a smaller ball causes it to roll faster and farther. The conclusion for the experiment also explains that the properties of a ball determine its speed.Another experiment related to the soccer ball experiment conducted is an experiment performed by Nancy K. O’Leary and Susan Shelly in one of O’Leary’s college classrooms. O’Leary is working on a Ph.D. in both biology and chemistry, and also teaches at both the high school and college level, whereas Shelly is a journalist. The experiment tested how various amounts of air pressure in a basketball affected its bounce. By starting with a standard pressure of 8 psi, the ball was dropped from a set height and its bounce height was measured with a meter stick. Then the psi of the basketball was increased or decreased by 1 psi, and the ball was bounced again as the new bounce heights were recorded. After the data was analyzed it was concluded that the higher the air pressure, the higher the basketball bounced (O’Leary and Shelly). This experiment is similar to the soccer ball experiment conducted because both tested the effect of air pressure in a ball. Also, both experiments measured the effect by releasing them from a set point and measuring a distance, although the basketball’s bounce height was measured versus the soccer ball’s rolling distance. The conclusion from the basketball experiment proved that air pressure has a positive effect on the performance of balls, within reason. This was applied to the soccer ball experiment in the idea that a higher air pressure would lead to a greater distance traveled by the soccer ball when rolled on the ground. Although the basketball was bounced and the soccer ball was rolled, this experiment still provided a general idea of how the soccer ball would perform in the experiment. From the detailed scientific concepts along with the presence of various similar experiments that were conducted by other researchers, it is obvious that there is much science behind the performance of balls that can be applied to the soccer ball experiment that was conducted. Whether it is soccer balls, basketballs, or even table tennis balls, factors such as air pressure, diameter, and ground surface play a key role in affecting ball velocity, bounce height, and distance traveled. The science behind these factors and the previously conducted experiments all lead to the hypothesis in the soccer ball experiment that high air pressure, low diameter, and the hardest ground surface, would result in the greatest distance traveled by the soccer ball. The findings of this experiment can be helpful for a better understanding of the soccer ball and how it works. Problem StatementProblem:To determine the effect of diameter, air pressure, and ground surface on the distance traveled by soccer balls rolled down a ramp.Hypothesis:The high air pressure value, low diameter, and low ground surface will cause the soccer ball to travel the farthest distance.Data Measured:The experiment was set up as a Three Factor DOE, with three runs of the DOE. The factors, or independent variables, in the experiment were diameter of the soccer, air pressure, and ground surface. The diameter was measured in inches, the air pressure in pounds per square inch (PSI), and the ground surface by the level of friction. The diameter values were 7” for the low, 8” for the standard, and 9” for the high. The pressure values were 6 psi for the low, 9 psi for the standard, and 12 psi for the high. The ground surfaces were asphalt for the low, dirt for the standard, and grass for the high. The dependent variable, or response variable, was the distance traveled by the soccer ball on the ground, which was measured in meters.Experimental DesignMaterials:Franklin Sports MLS Ball Maintenance Kit 7.5-Inch Inflating PumpPressure GaugeExtender Piece(3) Metal Needles Grass Surface Dirt Surface (Baseball Diamond Infield)Asphalt Surface (Parking lot)7” Diameter Size 3 Franklin Soccer Ball?8” Diameter Size?4 Baden?Classic?Soccer Ball 9” Diameter Size 5 Classic Sport Soccer Ball Empire?Level 100' Open Reel?Fiberglass Tape MeasureMMSTC Wooden Bowling RampTI-nspire CalculatorProcedures:Randomization1.Go to the random integer function on the calculator by pressing menu, probability, random, and then integer.2.In the randInt(), type in 1, 8, 8, to represent choosing the order of the eight non-standard trials in a Three Factor DOE.3.Record the trial order in the trial column of the data table, and follow that order when testing the different high and low values for each ground surface, air pressure, and diameter.Experiment1.Locate the three level surfaces (asphalt, dirt, and grass) on which to place the ramp. Make sure that the chosen areas are as level as possible so the soccer ball travels in a straight path. 2. Mark the start position on the ground surfaces chosen to ensure that when placing the ramp, the same area of ground surface is used.3. Use data table to find the surface that is to be used, and place the ramp on that surface.4.To check psi level of ball, attach needle to pressure gauge from ball maintenance kit. The low level pressure is 6 psi, the standard is 9 psi, and the high air pressure is 12 psi.5.Moisten needle and insert gauge slowly into ball. Read pressure gauge and remove from ball.6.If pressure is too low, attach other needle to pump. Moisten needle and insert pump slowly into ball. Inflate ball and recheck air pressure.7.If pressure is too high, attach other needle to extender piece, moisten, and insert into ball so that air can escape. Take piece out and recheck air pressure.8. Take one end of the tape measure and place it at the end of the ramp, and pull the tape measure out in a straight path from the bottom of the ramp as someone holds the other end. For the grass trials pull the tape measure out around 30 feet and for the high air pressure pull the tape measure out around 55 feet.9. Straighten the tape measure out as much as possible so that it acts as a guide to monitor how straight the ball is rolling, and then place the tape measure onto the ground surface.10. Take the soccer ball with the diameter that matches the trial number (7” for low, 8” for standard, and 9” for high), and hold it at the top of the ramp in the center.11. Release the ball from the top of the ramp and allow it to roll until stopping.12. When the ball stops, walk over to where the ball stopped rolling and read on the tape measure where the ball stopped rolling. Use the center of the ball as the point to match up with the measurement to ensure consistent tape measure reading. See Figure 4. 13.Record the measurement in the data table.14.Repeat steps 3-13 at the different high, low, and standard ground surface, air pressure, and diameter values until the 3 Factor DOE is finished, and then perform 2 more DOEs.Diagrams:Figure 2. Experimental MaterialsFigure 2 above shows the various materials used in the experiment, excluding the ramp and the ground surfaces. The ramp is shown later in Figure 3. Labels indicate what each material is.Figure 3. Experimental SetupFigure 3 above shows the format of the experiment. The ball is released from the top of the ramp after being placed in the center as shown in the soccer balls position in the figure. The ball is released and rolls down the ramp in a straight path next to the tape measure laid out as shown above. Then, the distance from the end of the ramp to the soccer ball is measured.Figure 4. Measuring the Distance TraveledFigure 4 above shows the point where the ball stopped rolling, at the end of a trial. This is the point where the distance rolled by the ball was measured and recorded by looking at the measuring tape. In this trial, the distance traveled by the ball was near 17.7 feet.Data and ObservationsTable 1Experiment DataTrial NumberGround Surface(Friction)Air Pressure (PSI)Diameter(Inches)Distance (feet)Run 1Run 2Run 3Average*****standardstandardstandard28.529.430.729.58+++17.718.720.318.94++-20.217.618.618.85+-+21.519.219.820.26+--16.818.318.918.0*****standardstandardstandard28.729.831.029.82-++36.538.036.937.11-+-43.846.044.144.63--+47.639.944.043.87---52.344.248.348.3******standardstandardstandard24.330.025.026.4Table 1 above shows the data collected from the soccer ball trials. A total of three 3 Factor DOEs were performed. The trial number column shows the order each of the trials were performed due to randomization. The ground surface, air pressure, and diameter columns all list whether a high, low, or standard value was used for that factor when performing the trial. The total distances traveled in each of the three DOEs are shown in the run columns. The distances were found by just reading the measurement off the tape measure. Then, the average of all three trials for each set of high, low, and standard values is shown in the average column.Table 2DOE Run 1 ObservationsDateTrialObservations4/231Researcher 1 inflated the low diameter ball to the high air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance the ball traveled.4/232Researcher 1 inflated the high diameter ball to the high air pressure and allowed ball to roll down the ramp. Research 2 measured and recorded the distance traveled.4/233Researcher 1 inflated the high diameter ball to the low air pressure and released the ball from the top of the ramp. Researcher 2 measured and recorded the distance traveled. It was very windy outside during this trial. The ball's path was not perfectly straight.4/234Researcher 1 inflated the low diameter ball to the high air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance the ball traveled. There was a large gust of wind during this trial. The grass was dry but the ground beneath it was slightly wet.4/235Researcher 1 inflated the high diameter ball to the low air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled by the ball. The grass was dry but the ground beneath it was slightly wet.4/236Researcher 1 inflated the low diameter ball to the proper air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled by the ball. The grass was dry but the ground beneath it was slightly wet.4/237Researcher 1 inflated the low diameter ball to the low air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled by the ball.4/238Researcher 1 inflated the high diameter ball to the high air pressure, rolled the ball down the ramp, measured the distance traveled by the ball. Researcher 2 recorded the distance traveled by the ball. The grass was dry but the ground beneath it was slightly wet.Table 2 above shows the observations taken during the first DOE performed. Significant occurrences were noted. All the trials of this DOE were performed on the same day, April 23, 2013, which was a relatively dry, sunny day.Table 3DOE Run 2 ObservationsDateTrialObservations4/261Researcher 1 inflated the low diameter ball to the high air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled. There was slight wind during this trial.4/262Researcher 1 inflated the high diameter ball to the high air pressure and allowed ball to roll down the ramp. Research 2 measured and recorded the distance traveled. The wind was blowing a lot during this trial.4/263Researcher 1 inflated the high diameter ball to the low air pressure and released the ball from the top of the ramp. Researcher 2 measured and recorded the distance traveled. 4/264Researcher 1 inflated the low diameter ball to the high air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance the ball traveled. The grass that the ball rolled on was wet and muddy.4/265Researcher 1 inflated the high diameter ball to the low air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled by the ball. The grass was wet and the ground was muddy.4/266Researcher 1 inflated the low diameter ball to the proper air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled by the ball. The grass was wet.4/267Researcher 1 inflated the low diameter ball to the low air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled by the ball.4/268Researcher 1 inflated the high diameter ball to the high air pressure, rolled the ball down the ramp, measured the distance traveled by the ball. Researcher 2 recorded the distance traveled by the ball. The grass was wet and muddy.Table 3 above shows the observations taken during the second DOE performed. Significant occurrences were noted. All the trials of this DOE were performed on the same day, April 26, 2013, which was a windy, wet day. Between the day of the first DOE and second DOE it rained and the grass was cut outside. Also, it was significantly colder than the day of the first DOE.Table 4 DOE Run 3 ObservationsDateTrialObservations4/261Researcher 1 inflated the low diameter ball to the high air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance the ball traveled. The wind picked up slightly during this trial. The ball curved slightly while rolling.4/262Researcher 1 inflated the high diameter ball to the high air pressure and allowed ball to roll down the ramp. Research 2 measured and recorded the distance traveled. It was very windy during this trial.4/263Researcher 1 inflated the high diameter ball to the low air pressure and released the ball from the top of the ramp. Researcher 2 measured and recorded the distance traveled4/264Researcher 1 inflated the low diameter ball to the high air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance the ball traveled. The grass was still wet and footprints started to form around the measuring tape where the ball rolled.4/265Researcher 1 inflated the high diameter ball to the low air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled by the ball. More footprints formed around the ball's rolling path.4/266Researcher 1 inflated the low diameter ball to the proper air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled by the ball. The wet ground was very muddy during this trial. The wind picked up a bit during this trial.4/267Researcher 1 inflated the low diameter ball to the low air pressure and rolled the ball down the ramp. Researcher 2 measured and recorded the distance traveled by the ball.4/268Researcher 1 inflated the high diameter ball to the high air pressure, rolled the ball down the ramp, measured the distance traveled by the ball. Researcher 2 recorded the distance traveled by the ball. The ground was very muddy during this trial. It was very windy.Table 4 above shows the observations taken during the third DOE performed. Significant occurrences were noted. All the trials of this DOE were performed on the same day, April 26, 2013, which was a windy, wet day. The trials from the third DOE were all performed on the same date as the trials from the second DOE.Figure 5. Ball’s Initial ReleaseFigure 5 above shows the initial release of the ball down the ramp. The distance measured in the experiment was from where the ball left the ramp to the point where the ball stopped moving. This initial point of where the ball left the ramp is what is shown in the figure.Figure 6. Soccer Ball Rolling Figure 6 shows the middle of a trial of the experiment. The high diameter soccer ball is rolling in a straight path along the measuring tape. In all the trials, the ball was allowed to roll in a near straight path, and this is what the figure above captures.Data Analysis and InterpretationData was collected using a comparative experiment to find the distance traveled by a soccer ball and how it was affected by ground surface, air pressure, and diameter. In order to ensure accuracy in the data collected, a control, randomization, and replication were used. The control was the standard trials. No experiment will be free of error; therefore, a control was used to limit the effect of lurking variables on the data. Randomization was done in order to further reduce any possible bias, and replication was used to ensure that the most accurate measurement possible was taken. The replication was achieved by performing three DOEs and then averaging the data from each one. Averaging many data points accounts for any trials where there might have been an error. The experiment that was done was analyzed using a three-factor Design of Experiment.Table 5FactorsFactors(-) ValuesStandard(+) ValuesGround Surface (friction)asphaltdirtgrassPressure of Ball (psi)6912Diameter of Ball (inches)789Table 5 shows the experimental values that were used in the experiment. The three factors were ground surface, pressure, and diameter. The low, standard, and high levels for ground surface were asphalt, baseball infield dirt, and grass. The low, standard, and high values for pressure were 6 psi (pounds per square inch), 9 psi, and 12 psi, and the low, standard, and high values used for diameter of the ball were 7”, 8” and 9”. The air pressure values were picked using the recommend air pressure for any given soccer ball, which is between 6 and 12 psi (Parrish). The diameter values were picked using the three basic soccer ball sizes, which are size 3 (7 inch diameter), size 4 (8 inch diameter), and size 5 (9 inch diameter). The ground surface valued were picked by taking common ground surfaces a soccer ball may be rolled on outside, and then ranking them by increasing pressure.Single Factor Effects:208597522225Factor: Ground Surface (G) Table 6Effect of Ground Surface-+37.118.944.618.943.820.248.318.0Avg: 43.5Avg: 19.0Effect = (19.0 - 43.5)/2 = 12.25 Figure 7. Effect of Ground SurfaceTable 6 shows the resulting distances when ground surface was low and when ground surface was high. Figure 7 shows how distance changed as ground surface went from low to high. As ground surface (friction) increases, distance traveled decreases by 12.25 feet.208597540005Factor: Pressure (P)Table 7Effect of Pressure-+20.218.918.018.843.837.148.344.6Avg: 32.6Avg: 29.9Effect = (29.9 – 32.6)/2 = -1.35 Figure 8. Effect of PressureTable 7 shows the resulting distances when pressure was low and when pressure was high. Figure 8 shows how distance changed as pressure went from low to high. As pressure increases, distance traveled decreases by 1.35 feet.2106930-5080Factor: Diameter (D)Table 8Effect of Diameter-+18.818.918.020.244.637.148.343.8Avg: 32.4Avg: 30.0Effect = (30.0 – 32.4)/2 = -1.2 Figure 9. Effect of DiameterTable 8 shows the resulting distances when diameter was low and when diameter was high. Figure 9 shows how distance changed as diameter went from low to high. As diameter increases, distance traveled decreases by 1.2 feet.Interaction Effects:Interaction of Pressure and Ground SurfaceTable 9Pressure and Ground Surface?Ground Surface (-)Ground Surface (+)Pressure (+)(solid segment)37.144.6 Avg: 40.918.918.8 Avg: 18.9Pressure (-)(dotted segment)43.848.3 Avg: 46.120.218.0 Avg: 19.12247900-9525Effect =(18.9 – 40.9)/2 – (19.1 – 46.1)/2= 2.5 Figure 10. Pressure and Ground SurfaceTable 9 shows the resulting distances and averages when pressure and ground surface are low and high. Figure 10 shows the interaction between pressure and ground surface. Segment P(-) is the dotted line segment for when pressure is low and ground surface goes from low to high. Segment P(+) is the solid line segment for when pressure is high and ground surface goes from low to high. The line segments for both low and high pressure show that there is a possible interaction between pressure and ground surface since their slopes are not equal, so the line segments are not parallel. The expected distance for low pressure is around 32.6 feet (Figure 8), but when ground surface goes from low to high, low pressure goes from 46.1 to 19.1, which is not very close to 32.6, meaning that ground surface likely had an effect. This is similar to the expected distance for high pressure, meaning that there is a possible interaction between ground surface and pressure. Interaction of Diameter and Ground SurfaceTable 10Diameter and Ground Surface?Ground Surface (-)Ground Surface (+)Diameter (+)(solid segment)37.143.8 Avg: 40.518.920.2 Avg: 19.6Diameter (-)(dotted segment)44.648.3 Avg: 46.518.818.0 Avg: 18.4225742518415Effect =(19.6 – 40.5)/2 – (18.4 – 46.5)/2= 3.6 Figure 11. Diameter and Ground SurfaceTable 10 shows the resulting distances and averages when diameter and ground surface are low and high. Figure 11 shows the interaction between diameter and ground surface. Segment D(-) is the dotted line segment for when diameter is low and ground surface goes from low to high. Segment D(+) is the solid line segment for when diameter is high and ground surface goes from low to high. The line segments for both low and high diameter show that there is a possible interaction between diameter and ground surface since their slopes are not equal, so the line segments are not parallel. The expected distance for low diameter is around 32.4 feet (Figure 9), but when ground surface goes from low to high, low diameter goes from 46.5 to 18.4, which is not very close to 32.4, meaning that ground surface likely had an effect. This is similar to the expected distance for high diameter, meaning that there is a possible interaction between ground surface and diameter.Interaction of Diameter and PressureTable 11Diameter and Pressure?Pressure (-)Pressure (+)Diameter (+)(solid segment)20.243.8 Avg: 32.018.937.1 Avg: 28.0Diameter (-)(dotted segment)18.048.3 Avg: 33.218.844.6 Avg: 31.722574251270Effect =(28.0 – 32.0)/2 – (31.7 – 33.2)/2= -1.25 Figure 12. Diameter and PressureTable 11 shows the resulting distances and averages when diameter and pressure are low and high. Figure 12 shows the interaction between diameter and pressure. Segment D(-) is the dotted line segment for when diameter is low and pressure goes from low to high. Segment D(+) is the solid line segment for when diameter is high and pressure goes from low to high. The line segments for both low and high diameter show that there is probably little to no interaction between diameter and pressure. The expected distance for low diameter is around 32.4 feet (Figure 9), and when pressure goes from low to high, low diameter goes from 33.2 to 31.7, which is close to 32.4, meaning that pressure likely had no effect. This is similar to the expected distance for high diameter, meaning that an interaction between diameter and pressure is not likely.Grand Average of all trials = 31.2Overall Effects of Single Factors:Effect of Ground Surface (G) = 12.25Effect of Pressure (P) = -1.35Effect of Diameter (D) = -1.2Interactions Between Factors:Effect of Pressure and Ground Surface (PG) = 2.5Effect of Diameter and Ground Surface (DG) = 3.6Effect of Diameter and Pressure (DP) = -1.25Prediction Equation:?=Grand Average+G+P+D+PG+DG+DP+noise?=31.2+12.25G+-1.35P+-1.2D+2.5PG+3.6DG+-1.25DP+noiseFigure 13. Prediction EquationFigure 13 shows the Prediction Equation used to predict experimental values. This equation includes the grand average of all trials except standards, the three main effects, the three interaction effects, and noise.Graph of Standards:Figure 14. Graph of StandardsFigure 14 shows a graph of all nine standard trials that were performed. The standards do not show any pattern and are consistent, which led to the conclusion that the experimental results are valid because there was a consistent control.Figure 15. Dot Plot of EffectsFigure 15 shows a dot plot of all six effects. All of the effects are less than 4 away from zero, with the exception of ground surface, which has an effect of 12.25. This suggests that ground surface had a more significant effect than all other single effects and interaction effects.Test of Significance:2×Range of Standards2×31.0-24.32×6.7=13.4Figure 16. Test of SignificanceUsing the test of significance shown in Figure 16, the range of standards and the rules of determining significant effects, only ground surface (G) was identified as a significant effect. An effect was considered significant if the absolute value of the effect was greater than twice the range of standards. Though 12.25 is within twice the range of standards, it clearly stands out from all the other effects, which are all between -2 and 4, therefore it is considered significant.Parsimonious Prediciton Equation:?=31.2+12.25G+noiseFigure 17. Parsimonious Prediction EquationFigure 17 shows the Parsimonious Prediction Equation. This shows the same thing as the Prediction Equation but only includes effects that were determined to be significant, the grand average, and noise. The only effect that was determined to be significant was ground surface (G), therefore it is the only effect used in this equation. The effects of diameter, pressure, and the three interaction effects of these single factors were not significant.ConclusionAn experiment was conducted using a three-factor Design of Experiment that tested the effect different factors had on the distance a soccer ball rolled. These factors were the ground surface the ball was rolled on, the diameter of the ball, and the air pressure of the ball. A ramp was placed on three different surfaces – asphalt, dirt, and grass. Three different ball diameters were used. The ball was inflated to one of the three psi levels and was rolled down the ramp, and the distance it took to stop was measured. The original hypothesis was that the low diameter ball with high pressure on asphalt would roll the farthest. This hypothesis was rejected. The factors that led to the ball going the farthest were low diameter, low pressure, and asphalt. The factors that led to the ball traveling the shortest distance were grass, low pressure, and low diameter. The hypothesis was partially correct but since low pressure and not high pressure caused it to roll farther, it was rejected.Diameter did have a small, negative effect on rolling distance, meaning that as ball diameter increased, distance traveled decreased slightly. Diameter of the ball should not have an effect on distance a ball travels. When the velocity of a rolling object is found, two expressions including mass are set equal to each other, so the mass cancels out and does not matter. The diameter (radius) also does not matter because when angular velocity is changed to velocity squared over radius squared, this is multiplied by the moment of inertia, which includes radius squared, so radius cancels out and does not affect velocity. Although diameter does have some effect on distance, it did not have a huge effect. Balls should not go dramatically farther or less far just because of what size they are. Different sizes are used in various levels of play but generally soccer balls will travel similar distances unless there is another variable affecting it.Higher air pressure also had a negative effect on distance. This went against the hypothesis. This result could have been slightly altered if different psi levels were used, because the effect air pressure had was small. The recommended inflation values for the smallest ball were 6 psi to 8 psi, so inflating this ball to the high psi value, 12 psi, could be the reason pressure had a negative effect. This ball would have performed best when inflated to a pressure within its range. The recommended inflation level for the largest diameter ball was 10 to 12 psi. Inflating this ball to the high pressure would cause it to perform normally, but inflating it to the low pressure had a negative effect. This is likely the reason why pressure had such a small effect. The low psi caused the smaller soccer ball to roll farther, but the high psi caused the larger ball to roll farther. The effects somewhat offset each other, but pressure still had an overall negative effect, leading to the conclusion that inflating a ball to a very high pressure or over-inflating it will cause it to go a shorter distance. This does agree with current findings because it is widely acknowledged that any kind of ball should always be inflated to a psi within its designated range.Ground surface was the last factor in the experiment. As the coefficient of friction of each surface increased, the distance traveled decreased. Asphalt cause the ball to go the farthest, dirt was in the middle, and grass caused it to go the least far. In this order, the surfaces have increasing coefficients. A higher coefficient means that the frictional force opposing the motion is greater. When there was a greater force going against the ball rolling, the ball, as expected, went a shorter distance. There was a greater negative acceleration because of the greater force, so the ball lost speed more quickly and did not go as far. Also, as the surfaces became harder – grass, dirt, asphalt – the ball traveled farther. This occurred because the ball could simply roll over the ground on the asphalt, while on the grass it had to push down each blade in order to roll over it. Another contributing factor was the ball being slightly pushed down into the ground. The ball could not be pushed into the asphalt, but it could have sunk into the dirt and the grass (or the dirt under the grass), causing it to have to work against the ground even more instead of just rolling forward. The grass was an uneven surface, and when objects roll on uneven surfaces they can be affected greatly by the small bumps. The asphalt has much smaller deformities, though, so the ball was much less affected by the surface and could travel farther. Overall, ground surface was determined to be the only significant effect, meaning that when determining the distance a ball rolls, ground surface is the only largely contributing factor.The results from the experiment agree with most of the current work in the field. The diameter and ground surface experiments mentioned earlier (Review of Literature) matched the results of the experiment that was conducted. However, the air pressure results did not match, due to the fact that the air pressure variable was difficult to manage with the different designated pressure ranges for each ball. Still, the results can be combined to help determine how the soccer ball would perform in other ways than just rolling in the ground. The table tennis experiment conducted by Yusaka Tsuji and Yoshitsugu Muguruma illustrated how different diameter balls perform in air travel (Tsuji and Muguruma 53). Since both their experiment and the one that was conducted here showed that increased diameter decreases velocity and distance traveled, the results could be combined to predict how the soccer ball would perform in air travel, such as after being kicked rather than rolled off a ramp. It can most definitely be hypothesized that diameter would continue to have a negative effect on the soccer ball’s distance traveled. Also, the results from the air pressure experiment from Nancy K. O’Leary and Susan Shelly showed air pressure had a positive effect (O’Leary and Shelly). If the soccer ball experiment was conducted with different air pressures that were proportional to the ball diameter rather than just the same high, low, and standard values for all diameter balls, then the results could be combined to predict how the soccer ball would travel when being bounced off the ground. From combining these results from all the experiments, a prediction of how a soccer ball would travel in all aspects of the game could be achieved, whether the ball is traveling through the air, bouncing off the ground, or rolling on the ground.Though the overall experiment was successful, there were some weaknesses and sources of error in the experiment. One of these flaws was in the air pressure variable. The low air pressure level for the experiment was not actually a low air pressure for the low diameter ball. Also, the high pressure level in the high diameter ball was at the top of its pressure range, but the level was well above the accepted pressure range for the low diameter ball. This caused the air pressure results to go against the science supporting that air pressure has a positive effect on the distance traveled by a soccer ball. Another weakness in the experiment was that the experiment was conducted outside in Michigan in the month of April. April weather in Michigan is very inconsistent, meaning that there were storms and rain on the different days of experimentation causing differences in the ground surface. Even though most trials were conducted on the second day of experimentation, that day was right after it had rained the day before so the ground was wet and muddy. The fact that the ground was wet and muddy could have limited the distance that the ball traveled, especially on the grass trials as the ball made indentations in the ground surface and had some mud on it which could have inhibited ball motion. This effect would be much higher in the grass trials, so the gap between the asphalt and grass surfaces could have been enlarged, which could have led to a significant effect for the ground surface factor. Also, in all the trials, the wind could have affected ball motion. The wind may have carried the soccer ball further in certain trials than in trials where the wind was calmer. The wind could have caused the ball to travel in less of a perfectly straight path. Though the trials should have been performed in times of low wind, the wind was present throughout all trials at various speeds, and due to time constraints, trials could not be held off to a less windy day.To further research the topic of soccer ball performance, one thing that could be done is testing the soccer ball when being kicked in the air. Ground travel is only a part of the soccer game, and a knowledge of different factors such as air pressure and diameter would help lead to a better understanding of the soccer ball's performance. Also, the experiment could be repeated using proportional air pressure rather than just set air pressures of 6, 9, and 12 psi. This would create more accurate results and more information about how air pressure affects the distance traveled by a soccer ball since the levels would be proportional to the accepted range of pressures for that specific ball diameter rather than just the accepted overall range for all balls. This would lead to more accurate results and a better scientific representation of how air pressure does affect a soccer ball when rolling down a ramp, possibly leading to results actually supporting the science in field. Also, other factors could be tested. In the Three-Factor DOE, only ground surface, air pressure, and diameter were tested. However, other factors affect how a soccer ball travels such as ball material. Though all soccer balls are made from synthetic leather, there are many different variations of it such as microfiber or ducksung (Monet). Adding additional factors such as ball material would allow athletes to do everything in their power to both understand their soccer ball, and to prepare their soccer ball in all aspects including air pressure, ball material, and the other possible test factors. One final idea for final research is to test different types of balls. Soccer balls were used so that the effect of air pressure could be researched, however ground surface and diameter effects can be applied to any ball-using sport. Basketballs, baseballs, softballs, and more could be tested in further research so that not only will the research benefit the field of soccer players, but it will benefit all sports that involve balls, reaching an even larger audience.Works CitedBarry. "Rolling Resistance and Fuel Economy." Barry's Tire Tech. N.p., n.d. Web.7 Apr. 2013. <, Tom. "Air Pressure." NASA. National Aeronautics and SpaceAdministration, 29 Mar. 2010. Web. 18 Apr. 2013.<, Rebecca. "The World's Most Beloved Sport - The History of Soccer."Soccerholics. Soccerholics, 30 Apr. 2005. Web. 18 Apr. 2013. <, Keith. "Pressure in a Soccer Ball." Schoolphysics. School Physics, 2007. Web. 07 Apr. 2013. < inmotion/text/Pressure_in_a_soccer_ball/index.html>.Kolitzus, Hans J. "Ball Roll Behavior."?Isss-. International Association for Sports Surface Sciences, n.d. Web. 12 May 2013. <, Ron. "Rolling Friction." School-for-champions. School for Champions, 18 Aug. 2008. Web. 07 Apr. 2013. <, Roy. "Chapter 6: Dynamics and Statics of Rigid Bodies." Motion and Mass: First Steps into Physics. Vol. 4. N.p.: Pari Center for New Learning, 2002. 61-74. Print. Basic Books in Science.Monet, Michael. "What Materials Are Used to Make a Soccer Ball? Read More:What Materials Are Used to Make a Soccer Ball?" EHow. Demand Media,Inc., n.d. Web. 18 Apr. 2013. <, C. R. "Friction and Area of Contact." Hyperphysics. Georgia State University, 2012. Web. 6 June 2013. <, C. R. "Rotational-Linear Parallels." Hyperphysics. Georgia State University, Aug. 2000. Web. 18 Apr. 2013. <;."Newton's First Law." Physics Classroom. The Physics Classroom, n.d. Web. 18Apr. 2013.<'Leary, Nancy K., and Susan Shelly. "Does It Matter How Much Air Is in YourBasketball?" The Complete Idiot's Guide to Science Fair Projects. New York City: Alpha, 2003. N. pag. Print.Parrish, Rogue. "How Does the Air Pressure of a Soccer Ball Affect the DistanceIt Goes When Kicked?" Livestrong. Demand Media, Inc., 26 May 2011. Web. 7 Apr. 2013. <, Angela. Rolling Friction Diagram. Digital image.?Biology Wikispaces. William Allen High School, 07 May 2013. Web. 06 June 2013. < diagram.png/282862736/288x296/types_of_friction_diagram.png>.Robertson, Bill. "Why Don't All Rolling Objects Reach the Bottom of an Incline atthe Same Time?" Science and Children 49.2 (2011): 62. Print.Schlager, Neil. "Friction: Science of Everyday Things." Real-Life Physics 2(2002): 52-58. Print.Tsuji, Yutaka, and Yoshitsugu Muguruma. Numerical Simulation of Motion ofTable Tennis Ball; Effect of Ball Diameter. Japan: Osaka University, n.d.38-53. Print. ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download