Switching Basics and Intermediate Routing
Switching Basics and Intermediate Routing
CCNA 3 Labs and Study Guide
ISBN: 1-58713-171-4
Errata
1st Printing
CHAPTER 1
Page 31 Missing figure 1-25 Topology for Lab 1-1
[pic]
Page 36 Missing figure 1-26 Topology for Lab 1-2
[pic]
Page 41 Task 11 Configure the IP host statements on router GAD
|Lab |Step |Error |Corrections |comment |
|Lab 1.2.3 Review of Basic |Task 11 Configure the IP host|GAD(config)#ip host BMH 172.18.0.1 |GAD(config)#ip host BHM 172.18.0.1 172.17.0.1. |Change typo from BMH to BHM |
|Router Configuration with RIP|statements on router GAD |172.17.0.1. | | |
CHAPTER 2
Missing several figures or answer figures are in place of empty boxes.
Replacement PDF Chapter available online at title/1587131714
Suggest tearing out entire chapter and replacing with the PDF copy
|Page |Figure # |Issue in First Printing |
|73 |2-1 |Missing figure |
|74 |2-1a |The answer figure is shown, should be an empty box |
|74 |2-1b |The answer figure is shown, should be an empty box |
|74 |2-1c |The answer figure is shown, should be an empty box |
|75 |2-1d |The answer figure is shown, should be an empty box |
|75 |2-1e |The answer figure is shown, should be an empty box |
|75 |2-1f |The answer figure is shown, should be an empty box |
|76 |2-1g |The answer figure is shown, should be an empty box |
|77 |2-2 |Missing figure |
|78 |2-3 |Missing figure |
|79 |2-4 |Missing figure |
|80 |2-5 |Missing figure |
|83 |2-6 |Missing figure |
|84 |2-7 |The answer figure is shown |
|84 |2-8 |The answer figure is shown |
|85 |2-9 |The answer figure is shown |
|87 |2-10 |Missing figure |
|91 |2-11 |Missing figure |
|97 |2-12 |Missing figure |
|102 |2-13 |Missing figure |
|106 |2-14 |Missing figure |
|110 |2-15 |Missing figure |
|115 |2-16 |Missing figure |
|122 |2-17 |The answer figure is shown |
Page 90 Task 6 Configure OSPF Routing on Router Rome
|Step |Error |Correction |Comment |
|Step 1 |Rome(config)#router ospf 1 |Rome(config)#router ospf 1 |Change typo in the lab book from 192.168.1.0 |
| |Rome(config-router)#network 192.168.1.0 0.0.0.255 |Rome(config-router)#network 192.168.0.0 0.0.0.255 area |to 192.168.0.0 |
| |area 0 |0 | |
| |Rome(config-router)#network 192.168.15.0 0.0.0.3 area|Rome(config-router)#network 192.168.15.0 0.0.0.3 area 0| |
| |0 | | |
|Step 3 |Rome(config)#router ospf 2 |Rome(config)#router ospf 1 |Change typo in the lab book from 2 to 1 |
Page 115 Table 2-14 Lab 2-7 Addressing Scheme
Device Interface IP Address Subnet Mask
RTA Fa0/0 192.168.1.1 255.255.255.192
S0/1 192.168.1.245 255.255.255.252
S0/0 192.168.1.254 255.255.255.252
Lo0 209.165.202.129 255.255.255.255
RTB S0/1 192.168.1.246 255.255.255.192
Fa0/0 192.168.1.65 255.255.255.192
S0/0 192.168.1.249 255.255.255.252
Correction: Change RTB S 0/0 mask from 255.255.255.192 to 255.255.255.252
CHAPTER 3
Page 157: The simulated LANs on RTB share the same bit pattern for the first 21 bits...
should be: The simulated LANs on RTB share the same bit pattern for the first 17 bits...
CHAPTER 6
Page 229 Figure 6-15 - Figure is up above the beginning of the lab in the middle of the previous lab's text
CHAPTER 8
Page 268 Task 16: Test the VLANs
Step 1. Ping from the host in port 0/4 to the host in port 0/8.
Was the ping successful?
Why?
Step 2. Ping from the host in port 0/8 to the host in port 0/4.
Was the ping successful?
Step 3. Ping from the host in port 0/4 to the switch IP 192.168.1.2.
Was the ping successful?
Step 4. Ping from the host in port 0/8 to the switch IP 192.168.1.2.
Was the ping successful?
Correction: Port 0/4 should be change to port 0/5
CHAPTER 9
Page 292 The switch prompt in Task 5 under the “2900 Switch” should be change from Switch_A(config)#exit
To – Switch_A(vlan)#exit
Page 294 TASK 12 Create the ISL Trunk
|Error |Correction |Comment |
|Switch_A(config)#interface fastethernet 0/1 |Switch_A(config)#interface fastethernet 0/1 |If you are using 3550 switch, you need to setup encapsultion|
|Switch_A(config-if)#switchport mode trunk |Switch_A(config-if)#switchport trunk encapsulation isl |before setup the port as trunk port. |
|Switch_A(config-if)#switchport trunk encapsulation isl |Switch_A(config-if)#switchport mode trunk | |
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
Related searches
- difference between intermediate and standard car
- word basics and features
- probability and statistics basics pdf
- html and javascript basics pdf
- rifle scope basics and terminology
- ccna routing and switching 200 125 pdf
- forces and motion basics simulations answers
- phet simulation forces and motion basics key
- forces and motion basics phet lab
- basics of bookkeeping and accounting
- cbt basics handouts and worksheets
- accounting basics debits and credits