Power Liftgate / DRIVE UNIT / Removal



Power Liftgate / DRIVE UNIT / Removal

REMOVAL

|[pic] |

1. Open the liftgate.

 

2. Disconnect and isolate the battery negative cable.

 

3. Remove the liftgate scuff plate.

a. Using a trim stick C-4755 or equivalent, disengage the liftgate scuff plate retaining clips (1).

 

b. Carefully disengage the scuff plate end tabs (4) from the left and right quarter trim panels (5).

 

c. Remove the liftgate scuff plate (3) from the liftgate opening.

 

|[pic] |

 

4. Remove the upper D-pillar trim.

a. Using a trim stick C-4755 or equivalent, disengage the upper D-pillar trim retaining clips (2).

 

b. Carefully disengage the upper D-pillar trim end tab (5) from the rear header trim plate.

 

c. Disconnect the power liftgate D-Pillar switch and third row power folding seat switch electrical connectors (3) (if equipped).

 

d. Remove the upper D-pillar trim from the liftgate opening.

 

|[pic] |

 

5. Remove the quarter trim bolster (5).

a. Using a trim stick C-4755 or equivalent, disengage the front and rear quarter trim bolster retaining clips (1).

 

b. Carefully disengage the quarter trim bolster upper retaining tabs (2) by lifting the bottom edge of the bolster.

 

c. Continue pulling the quarter trim bolster away from the quarter trim panel to disengage the quarter trim bolster locating tabs (4).

 

d. Slide the rear seat belt (3) out of the slot in the quarter trim bolster.

 

e. Remove the quarter trim bolster (5).

 

|[pic] |

 

6. Remove the left quarter trim panel (5).

a. Remove the third row lower seat belt webbing anchor (4).

 

b. Remove the third row upper turning loop anchor bolt.

 

c. Remove the six quarter trim retaining screws.

 

d. Pull trim from inner quarter panel (1).

 

e. Disconnect the auxiliary power outlet and power inverter (2) wire harness connectors (3) (if equipped).

 

f. Remove the left quarter trim panel (5).

 

|[pic] |

 

7. If equipped, remove the subwoofer, 

 

8. Remove the link rod assembly from the liftgate attachment point, 

 

9. Remove the drive unit assembly retaining bolts (4).

 

10. Disconnect the wire harness connector from the power liftgate drive unit assembly (3).

 

11. Unhook the drive unit assembly (1) from the D-pillar (2) and remove the unit from the vehicle.

.

 

INSTALLATION

|[pic] |

1. Install the power liftgate drive unit assembly (3) onto the D-pillar (2).

 

2. Insure that the drive unit bracket mounting tab is properly seated into the hole on the D-Pillar (1).

 

3. Install the drive unit retaining bolts (4). Tighten the bolts to 26 N·m (19 ft. lbs.).

 

4. Connect the wire harness connector to the drive unit assembly.

 

5. If equipped, install the subwoofer, 

|[pic] |

 

6. Install the left quarter trim panel (5).

a. Position the left quarter trim panel (5) into the vehicle.

 

b. Connect the auxiliary power outlet and power inverter (2) wire harness connectors (3) (if equipped).

 

c. Align the trim panel over the retaining slots on the inner quarter panel (1) and firmly snap into place.

 

d. Install the six quarter trim retaining screws.

 

e. Install the third row upper turning loop anchor bolt.

 

f. Install the third row lower seat belt webbing anchor (4).

 

|[pic] |

 

7. Install the quarter trim bolster (5).

a. Position the quarter trim bolster (5) into the vehicle and slide the rear seat belt (3) into the slot.

 

b. Align the locating tabs (4) with the holes in the left quarter trim panel.

 

c. Carefully engage the quarter trim bolster upper retaining tabs (2) by inserting them into the left quarter trim panel and swinging the bottom edge of the bolster towards the left quarter trim.

 

d. Push the quarter trim bolster into the left quarter trim panel until the retaining clips (1) are fully seated.

 

|[pic] |

 

8. Install the upper D-pillar trim.

a. Position the upper D-pillar trim into the liftgate opening.

 

b. Connect the power liftgate D-Pillar switch and third row power folding seat switch electrical connectors (3) (if equipped).

 

c. Carefully engage the upper D-pillar trim end tab (5) into the rear header trim plate.

 

d. Push the upper D-pillar trim onto the D-Pillar to engage the trim retaining clips (2).

 

|[pic] |

 

9. Install the liftgate scuff plate.

a. Position the liftgate scuff plate (3) into the liftgate opening.

 

b. Carefully engage the scuff plate end tabs (4) into the left and right quarter trim panels (5).

 

c. Push the liftgate scuff plate down onto the liftgate opening to engage the scuff plate retaining clips (1).

 

 

10. Connect the battery negative cable.

 

11. Using an appropriate scan tool, check and erase any power liftgate control module diagnostic trouble codes.

12. Verify power liftgate system operation.

 

 

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download