EARLY COMM VIDEO CHECKOUT



Issue 1

Index of content:

Pre-existing procedures (not final versions):

DESPITE BEING AN OLD ISSUE,

THESE PROCEDURES HAVE BEEN EDITED BY Lou McFadin.

PLEASE REVIEW THEIR CONTENT AGAINST THE EXISTING, APPROVED, VOICE/PACKET PROCEDURES.

Log of changes:

Step 3.4

Step 4.3

Step 4.4 and Note

Step 4.5

1. ham radio setup

2. VOICE OPERATIONS

3. FREQUENCY SELECTION

4. PACKET OPERATIONS

5. POWERDOWN

6. ISS HAM RADIO STOWAGE

NEW PROCEDURES:

ITEMS HIGHLITED IN YELLOW ARE To BE REVIEWS BEFORE OFFICIAL RELEASE

7 SSTV CONFIGURATION SETUP

8 SSTV OPS – POWER UP

9 SSTV OPS – ADDITIONAL SET UP

10 SSTV OPS - IMAGES RECEPTION

11 SSTV OPS – MANUAL IMAGES TRANSMISSION

12 SSTV OPS – SLIDE SHOW MODE

13 SSTV OPS – BEACON MODE

14 SSTV OPS – REPEATER MODE

15 SSTV OPS – IMAGES MANAGEMENT

16 SSTV OPS – DEFAULT SW CONFIGURATION

17 SSTV POWERDOWN

18 SSTV CONFIGURATION STOWAGE

19 SSTV SOFTWARE INSTALLATION

20 SSTV SW INSTALLATION VERIFICATION

21 SSTV SW AUDIO LEVEL ADJUSTMENT

F.B 29/01/2003

|NOTE |

|These procedures assume the SSC is connected to the Packet Module POWER OUT (J2) port. |

|References to "PGSC" in the documentation are synonmous with "SSC." |

[pic]

Figure 1 - Ham Radio Setup Configuration.

1. ham radio setup

1.1 UNSTOW HAM RADIO EQUIPMENT:

VHF Transceiver (Ericcson) MP-A-VHF/UHF

Power Adapter Module (SXISS98300)

Ericsson Cable (SXISS98401)

Packet Module (SXISS98100)

Transceiver Cable (SXISS98400)

Headset Noise Reducing (40433G-01)

Headset Extension Cable (sxiss99402)

Adapter Module (sxiss98200)

ISS Ham 28V DC Power Cable (sxiss99404)

1.2 DC Outlet Off ( OFF

1.3 (VHF Transceiver Pwr/Vol ( off

(Packet Module POWER ( OFF

1.4 Unstow:

RS232 9-9Pin PGSC Cable Assy (SED33103348-307)

ORB DC Power Cable 10' (SEG39129264-303)

RS/Orb DC Power Supply (SED39126010)

DC Power Supply Adapter Cable 10’ (SEG39129263)

SSC (SDZ39129262)

Antenna Cable (SXISS99403)

SSC 1.5 (SSC Pwr – off

1.6 Power Adapter Module (|( VHF Transceiver

Ericsson Cable (|( VHF Transceiver

Ericsson Cable (|( Adapter Module RAD (J2) port

VHF Transceiver (|( Adapter Module using Velcro

Antenna Cable (|( VHF Transceiver and FGB Panel 414

Packet Module TRANSCEIVER (J3) port (|( Power Adapter Module PKT (J1) port using Transceiver Cable

SSC (|( Packet Module DATA (J4) port with RS232 9-9Pin PGSC Cable Assy

Packet Module POWER OUT (J2) port (|( RS/Orb DC Power Supply with ORB DC Power Cable 10'

DC Power Supply Adapter Cable 10’ (|( RS/Orb DC Power Supply and SSC

Outlet (|( Packet Module POWER IN (J1) port with ISS Ham 28V DC Power Cable

If Headset Extension Cable used,

Headset Noise Reducing (|( Headset Extension Cable (|(Adapter Module HDST (J3) port

Otherwise,

Headset Noise Reducing (|( Adapter Module HDST (J3) port

2. VOICE OPerationS

2.1 (DC 10 AMP OUTLET ( ON

2.2 Packet Module POWER (S1) ( ON

Packet Module PACKET EN (G)/DISABLE (R) ( DISABLE (R)

Power Adapter Module ( ON

Adjust VOLUME

2.3 sel VHF Transceiver frequency desired

2.4 Perform voice contacts.

|NOTE |

|Check transceiver temp strips for overtemp after long periods of transmission. |

|Temporarily discontinue use if overtemp occurs. |

If Voice operations complete, to resume Automatic Packet operations

Select frequency desired (A1 or E9 nominal for packet operations)

Packet Module PACKET EN (G)/DISABLE (R) - EN (G)

3. frequency selection

3.1 GO TO {5.202 ISS HAM FREQUENCY REFERENCE} (SODF: INTEG: REFERENCE: ISS HAM)

sel VHF Transceiver frequency desired

3.2 To change memory banks,

pb MENU ( Push

|MODE |

3.3 To select memory banks,

pb SEL ( Push repeatedly

|VHF |UHF |

|Zone A |A1-A16 |Zone E |E1-E16 |

|Zone B |B1-B16 |Zone F |F1-F16 |

|Zone C |C1-C16 |Zone G |G1-G16 |

|Zone D |D1-D16 |Zone H |H1-H16 |

3.4 pb EXIT ( Push to confirm selection

|NOTE |

|Rotary switch (1-16) allows selection of individual frequency within each|

|bank of frequencies. |

|VHF | |UHF |

|B6 |Packet world-wide |E9 |

|A2, A3 |Voice world-wide |F4 |

|B1, B2 |Europe voice |F3, F4 |

4. PACKET OPerationS

4.1 (DC 10 AMP OUTLET ( ON

4.2 Packet Module POWER (S1) ( ON

Packet Module PACKET EN (G) /DISABLE (R) ( EN (G)

Power Adapter Module ( ON

4.3 sel frequency desired (B6 or E9 nominal for packet operations)

SSC 4.4 START MENU: Programs: Station Apps/WINPACK

|NOTE |

|1. An alternative program to use for packet communications is called “HyperTerminal” or|

|“HT”. |

| |

|2. Packet module requires RS232 9-9 Pin PGSC Cable Assy port configured for 9600 baud, |

|8-bit word-length, no parity, and 1 stop bit. |

| |

|3. To list messages in the Personal Message System, at the cmd prompt, input: list. |

Table 1. Personal Message System User Commands.

|Bye |Log off and disconnect |

|Help |or ? displays list of command instructions |

|Jlog |causes a copy of the heard log to be sent to the user |

|Kill n |delete message n |

|KM |kills all messages addressed to or from the user’s callsign |

|List |lists all messages currently stored in the packet module |

|Mine |lists all messages addressed to or from the user’s callsign |

|Read n |read message n |

|SB |send a message with bulletin identifier |

|Send |send a message |

|SP |send a message with personal/private identifier |

|SR n |send a reply using message n “FROM” field |

|ST |send a message with the NTS identifier |

|Version |displays firmware version information |

4.5 If desired, Minimize WINPACK window to run in background.

5. Powerdown

5.1 POWER ADAPTER MODULE ( OFF

SSC power ( OFF

Packet Module POWER (S1) ( OFF

5.2 DC 10 AMP outlet ( OFF

6. Iss ham radio STOWage

6.1 (DC 10 AMP OUTLET ( OFF

6.2 ISS Ham 28V DC Power Cable (|( outlet and Packet Module

ORB DC Power Cable 10' (|( Packet Module and RS/Orb DC Power Supply

RS232 9-9Pin PGSC Cable Assy (|( RS/Orb DC Power Supply and SSC

RS232 9-9Pin PGSC Cable Assy (|( SSC and Packet Module

Ericsson Cable (|( Adapter Module

Antenna Cable (|( VHF Transceiver and FGB Panel

Headset Extension Cable and Headset Noise Reducing (|( Adapter Module

VHF Transceiver (|( Adapter Module Velcro fastener

6.3 Stow ISS HAM

|NOTE |

|1. The following SSTV procedures assume the ISS HAM equipment is already set up as per|

|ISS HAM SETUP. |

| |

|2. The following SSTV procedures also assume that the SSTV software is installed in |

|the SSC as per SSTV SOFTWARE INSTALLATION. |

[pic]

Figure 2 - Ham Radio with SSTV Setup Configuration.

7 SSTV CONFIGURATION SETUP

7.1 UNSTOW ADDITIONAL SSTV EQUIPMENT:

SSTV/VOX Module (SXISS00501 TBC)

SSTV Computer Cable (SXISS02417 TBC)

SSTV Interface Cable (SXISS02418 TBC)

If Webcam available,

Webcam (p.n. TBD)

SSC 7.2 (SSC Pwr – off

7.3 (VHF Transceiver Pwr/Vol – OFF

(Packet Module POWER (S1) – OFF

7.4 Adapter Module AUX (J1) port (|( Transceiver Cable

Leave cable end free

7.5 SSTV Interface Cable (|( Adapter Module AUX (J1) port

SSTV Interface Cable (|( SSTV/VOX Module ADAPTER MODULE (J2) port

SSTV Computer Cable (|( SSTV/VOX Module COMPUTER (J1) port

SSTV Computer Cable TXA Plug (|( SSC Ear (Jx TBD) port

SSTV Computer Cable RXA Plug (|( SSC Line In (Jx TBD) port

If Line In port not available,

use Mic (Jx TBD) port

If Webcam available,

Webcam cable (|( SSC USB (Jx TBD) port

8 SSTV OPS – POWER UP

8.1 (DC 10 AMP OUTLET ( ON

8.2 Packet Module POWER (S1) ( ON

Packet Module PACKET EN (G)/DISABLE (R) ( DISABLE (R)

Power Adapter Module ( ON

VHF Transceiver Pwr/Vol ( Adjust to mid-range

|NOTE |

|A correct audio level at the SSC audio input is provided by a 3 to 4 bars indication in|

|the Signal Strength Indicator of the SSTV program. See Figure 3. |

[pic]

Figure 3 – Audio signal strength indicator showing correct audio level.

8.3 sel VHF Transceiver frequency desired {FREQUENCY SELECTION}

|NOTE |

|While the ISS HAM equipment is configured for SSTV operations, Voice operations are |

|still possible via the Headset connected to the Power Adapter Module. |

SSC 8.4 SSC Pwr ( ON

START MENU: Programs: Station Apps: SPACECAM

SSC Audio Volume ( Adjust {SSTV AUDIO LEVEL ADJUSTMENT}

SSC 9 SSTV OPS – ADDITIONAL SET UP

9.1 TO ADD A TEXT OVERLAY TO TRANSMITTED IMAGES,

Click on the TEXT Tab

Enter the desired text into the Text Overlay field

Adjust the text overlay position over the image by means of the Upper, Center, Lower and the Left Justified, Centered, Right Justified radio buttons

Click on the ENABLE checkbox to check it

Click on the MANUAL Tab

9.2 To disable addition of text overlay to transmitted images,

Click on the TEXT Tab

Click on the ENABLE checkbox to uncheck it

Click on the MANUAL Tab

9.3 To add a guest crewmember callsign to transmitted images,

Click on the TEXT Tab

Enter the guest crewmember callsign into the “Guest” callsign field

Click on the MANUAL Tab

9.4 To disable the addition of a guest crewmember callsign to transmitted images,

Click on the TEXT Tab

Clear the “Guest” callsign field

Click on the MANUAL Tab

9.5 To modify Slide-Show Mode interval,

Click on the SETTINGS Tab

Adjust the Slide Show – Delay control slider to set the required interval in minutes

Click on the MANUAL Tab

SSC 10 SSTV OPS - IMAGES RECEPTION

|NOTE |

|1. After starting, the SSTV software is ready to automatically receive and store |

|images transmitted from ground stations. This condition is marked by the Auto-RECEIVE |

|button being highlighted. |

| |

|2. Received images are stored in the DEFAULT image collection. |

10.1 To disable automatic images reception,

Click on the STANDBY/ABORT button, or [S]

10.2 To re-enable automatic images reception,

Click on the Auto-RECEIVE button, or [A]

10.3 To manually force the reception of an image,

Click on the RECEIVE button, or [R]

At the end of the reception the software will transition back to Auto-RECEIVE mode.

10.4 To synchronize the reception of an image which appear to be badly framed or skewed,

Click on the RE-SYNC button, or [Y]

10.5 To abort the ongoing reception of an image,

Click on the STANDBY/ABORT button, or [S]

If automatic reception is required,

Click on the Auto-RECEIVE button, or [A]

10.6 To enable automatic retransmission of a received image

See {SSTV OPS – REPEATER MODE}

|NOTE |

|A correct audio level at the SSC audio input is provided by a 3 to 4 bars indication in|

|the Signal Strength Indicator of the SSTV program. See Figure 3. |

SSC 11 SSTV OPS – MANUAL IMAGES TRANSMISSIOn

|NOTE |

|1. The duration of an image transmission depends on the SSTV standard selected. With |

|the ROBOT 36 standard (default mode) the transmission lasts about 45 seconds. |

| |

|2. Performing a manual image transmission will abort any ongoing Slide Show / Beacon |

|mode, Repeater mode, or image reception. |

11.1 To transmit an image stored in the SSC,

sel Image to be transmitted from one of the Image Collections {IMAGES MANAGEMENT}

The selected image is copied in the LH Image Window

Click on the TRANSMIT button, or [T]

11.2 To transmit an image captured with the WebCam,

(WebCam connected

(Enable video checked

The RH Image Window shows the input from the WebCam

Point the WebCam

When ready for capturing an image,

Click on Camera Grab button, or [C]

The captured image is copied in the LH Image Window

Click on the TRANSMIT button, or [T]

11.3 To abort the ongoing transmission of an image,

Click on the STANDBY/ABORT button, or [S]

If automatic reception is required,

Click on the Auto-RECEIVE button, or [A]

SSC 12 SSTV OPS – SLIDE SHOW MODE

|NOTE |

|1. During the interval between two subsequent image transmission in Slide Show mode, |

|it is possible to receive images if the program is configured to do so (Auto RECEIVE |

|button highlighted). |

| |

|2. Slide Show mode can operate together with Repeater mode. |

12.1 To enable the Slide Show mode for all the images contained in one directory,

(DISK icon button - pushed

sel Image Collection to be transmitted {IMAGES MANAGEMENT}

Click on the Slide Show ON button, or [O]

12.2 To enable the Slide Show mode with images captured from the WebCam,

(WebCam connected

(Enable video checked

The RH Image Window shows the input from the WebCam

(CAMERA icon button - pushed

Point the WebCam

When ready for starting the Slide Show mode,

Click on Slide Show ON button, or [O]

Each captured image is copied in the LH Image Window before transmission

12.3 To abort the ongoing transmission of an image,

Click on the STANDBY/ABORT button, or [S]

Slide Show mode is disabled too.

If automatic reception is required,

Click on the Auto-RECEIVE button, or [A]

12.4 To disable the ongoing Slide Show mode,

Click on the Slide Show OFF button, or [F]

An ongoing transmission will be completed.

SSC 13 SSTV OPS – BEACON MODE

|NOTE |

|1. Beacon mode is a special application of Slide Show mode, which requires a single |

|image to be stored in a separate directory. |

| |

|2. Repeater mode can operate together with Slide Show mode. |

13.1 To enable the Slide Show mode for all the images contained in one directory,

Select in the USER Image Collection {IMAGES MANAGEMENT} the directory which contain the image to be transmitted in Beacon mode.

Verify that the Image Collection contains only one image.

Click on the Slide Show ON button, or [O]

An ongoing transmission will be completed.

13.2 To abort the ongoing transmission of an image,

Click on the STANDBY/ABORT button, or [S]

Beacon mode is disabled too.

If automatic reception is required,

Click on the Auto-RECEIVE button, or [A]

13.3 To disable the ongoing Beacon mode,

Click on the Slide Show OFF button, or [F]

An ongoing transmission will be completed.

SSC 14 SSTV OPS – REPEATER MODE

|NOTE |

|1. Repeater mode can operate together with Slide Show / Beacon mode. |

| |

|2. Images received and retransmitted while in Repeater mode will be saved in the |

|REPEATED Image Collection (if the relevant option is selected). |

14.1 To enable the Repater mode,

(Auto RECEIVE button – highlighted

Click on the Repeater tab

Click on the Repeater Mode checkbox to check it

If it is desired that repeated images are stored on disk,

Click on the Save Repeated Images checkbox to check it

Click on the Manual tab

14.2 To abort the ongoing transmission of an image,

Click on the STANDBY/ABORT button, or [S]

If active, Slide Show / Beacon mode is disabled too.

If automatic reception is required,

Click on the Auto-RECEIVE button, or [A]

14.3 To disable the ongoing Repeater mode,

Click on the STANDBY/ABORT button, or [S]

An ongoing transmission will be completed.

SSC 15 SSTV OPS – IMAGES MANAGEMENT

IMAGES ARE MANAGED BY MEANS OF FIVE (5) PREDEFINED COLLECTIONS. FOUR (4) COLLECTIONS REFERS TO IMAGE FILES CONTAINED IN PREDEFINED DIRECTORIES. THE FIFTH COLLECTION CAN BE DIRECTED TO ANY USER DIRECTORY OF THE SSC.

|Collection |Directory |Usage |

|DEFAULT |§\SPACECAM\DEFAULT |Used to store images received from Ground Stations. |

|LIBRARY |§\SPACECAM\LIBRARY |Used to store images gathered from different sources |

| | |including those provided with the application. |

|REPEATED |§\SPACECAM\REPEATED |Used to store images received from Ground Stations and|

| | |subsequently repeated (if Repeater Mode and the |

| | |relevant option are both selected). |

|CREW |§\SPACECAM\CREW |Used to store images which are preferably kept |

| | |separate from the others. |

|USER |Any SSC directory |Any image found in a user selected directory of the |

| | |SSC (not in a CD-ROM file system). |

§ indicates the software installation path: C:\Program Files\ISS HAM

Images management, apart from the automatic storage performed on received images, shall be performed by the crew by means of SSC file system tools (like Resource Explorer).

Any image in any collection, not in a CD-ROM file system, can be selected for transmission to Ground.

15.1 To change a USER collection directory,

Double-click on the USER tab

sel a directory by navigating through folders

Click on SELECT

SSC 16 SSTV OPS – DEFAULT SW CONFIGURATION

|NOTE |

|Between successive executions of the SSTV software, the SETTINGS, the Text Overlay |

|content and the Guest Callsign are preserved. |

16.1 (SSTV Mode – Robot 36

(Auto Save – checked

(Lock Mode – unchecked

16.2 (MANUAL Tab : Auto RECEIVE – highlighted

(MANUAL Tab : Slide Show OFF – highlighted

(MANUAL Tab : Enable Video – unchecked

16.3 (REPEATER Tab: Repeater Mode – unchecked

(REPEATER Tab: Save Repeated Images – unchecked

16.4 (SETTINGS Tab : Sharpness – set to 4

(SETTINGS Tab : No Filter – unselected

(SETTINGS Tab : High Pass – unselected

(SETTINGS Tab : Bandpass – unselected

(SETTINGS Tab : Narrow BP – selected

(SETTINGS Tab : Sensitivity – set to 3

(SETTINGS Tab : Delay – set to 1 minutes

(SETTINGS Tab : Adjust Slant : RX samp. rate – Set to 11025.00

(SETTINGS Tab : Adjust Slant : TX samp. rate – Set to 11025.00

16.5 (TEXT Tab : Guest Callsign – empty

(TEXT Tab : Text Overlay – empty

(TEXT Tab : Enable – unchecked

17 SSTV POWERDOWN

SSC 17.1 CLICK ON THE TOP-RIGHT CORNER (X BUTTON)

to close the SSTC program

Exit Windows

17.2 Power Adapter Module ( OFF

SSC power ( OFF

Packet Module POWER (S1) ( OFF

17.3 DC 10 AMP outlet ( OFF

18 SSTV CONFIGURATION STOWAGE

|NOTE |

|This procedure will revert the ISS HAM RADIO set up to the configuration used for |

|normal voice/packet operations. For further stowage see ISS HAM RADIO STOWAGE. |

18.1 (DC 10 AMP outlet ( OFF

18.2 SSTV Interface Cable (|( Adapter Module AUX (J1) port

SSTV Interface Cable (|( SSTV/VOX Module ADAPTER MODULE (J2) port

SSTV Computer Cable (|( SSTV/VOX Module COMPUTER (J1) port

SSTV Computer Cable TXA Plug (|( SSC Ear (Jx TBD) port

SSTV Computer Cable RXA Plug (|( SSC Line In (Jx TBD), or Mic (Jx TBD), port

If Webcam available,

Webcam cable (|( SSC USB (Jx TBD) port

18.3 Power Adapter Module AUX (J1) port (|( Transceiver Cable

Reconnect free end

18.4 Stow ISS HAM SSTV equipment

|NOTE |

|1. The following procedure asssume the SSC connected to the ISS HAM hardware |

|in order to receive power from it. However no additional SSTV hardware is |

|required. |

| |

|2. The following procedure shall be accomplished at least once for every SSC, |

|which is to be enabled for for ISS HAM SSTV operations. |

| |

|3. The following procedure can also be used to perform software updates. |

19 SSTV SOFTWARE INSTALLATION

19.1 UNSTOW ISS HAM CD-ROM (P.N. TBD)

19.2 (DC 10 AMP outlet ( ON

(Packet Module POWER (S1) ( ON

SSC 19.3 POWER ( ON

19.4 Insert CD-ROM

Open CD-ROM and locate file spacecam_setup.exe

|CD ROM content |

|Filename |Description |

|Spacecam_setup.exe |Installation program for SPACECAM |

|Other files TBD | |

| | |

| | |

19.5 Double click on file spacecam_setup.exe

After a brief initialization the InstallShield Wizard for SpaceCam dialog box appears.

19.6 Click on Next

If the program has already been installed on the SSC,

the situation is recognized and the user is prompted to Modify/Repair/Remove the installation.

Before performing an installation, it is required for the existing one to be removed:

Select Remove and then Click on Next

Click on Remove

Removal of previous installation is performed

Click on Finish

Go to 19.5 to restart the installation

19.7 The program is to be installed in the default directory C:\Program Files\ISS HAM\SPACECAM. If a different directory is required then click on Change… and select/type a new installation directory

Click on Next

19.8 Verify installation parameters and click on Install

Program files are installed.

19.9 Click on Finish

Eject CD-ROM

19.10 Stow CD-ROM

Go to SSTV SW INSTALLATION VERIFICATION

20 SSTV SW INSTALLATION VERIFICATION

SSC 20.1 (EAR PORT (JX TBD) – DISCONNECTED (FREE).

20.2 START MENU: Programs: Station Apps: SPACECAM

20.3 Click on LIBRARY Tab and double-click on any of the available images.

The image is copied in the LH Image Window

20.4 Click on TRANSMIT [T]

(An audio tone is heard over the internal laptop loudspeaker and the scanning process is highlighted over the image. The transmission lasts about 45 seconds.

If no tone heard, or tone too low

{SSTV AUDIO LEVEL ADJUSTMENT}

then

repeat 20.4

20.5 If WebCam not available,

Click on the top-right corner (X button)

to close the SSTV program

Exit Windows

Go to 20.14

|NOTE |

|1. The prosecution of the procedure is required only if a webcam is available |

|for connection to the SSC. |

| |

|2. The operation of the webcam, as well as the installation of any required |

|software drivers in the target SSC, is considered to be already accomplished. |

20.6 Unstow Webcam hardware (p.n. TBD)

20.7 Webcam cable (|( SSC USB port (Jx TBD)

SSC 20.8 START MENU: Programs: Station Apps: SPACECAM

|NOTE |

|Do not connect the Webcam to the SSC with the SSTV SW (SPACECAM) already |

|running. |

20.9 Click on Enable Video to check the box

Images captured by the Webcam are shown in the RH Image Window

20.10 Click on CAMERA GRAB [C]

The image available at the instant of the clicking is transferred to the LH Image Window

20.11 Click on TRANSMIT [T]

(An audio tone is heard over the internal laptop loudspeaker and the scanning process is higlighted over the image. The transmission lasts 45 seconds.

If no tone heard, or tone too low

{SSTV AUDIO LEVEL ADJUSTMENT}

then

repeat 20.11

20.12 Click on the top-right corner (X button)

to close the SSTV program.

Exit Windows

20.13 Webcam cable (|( SSC USB port

Stow Webcam hardware

SSC 20.14 POWER ( OFF

20.15 Packet Module POWER (S1) ( OFF

DC 10 AMP outlet ( OFF

21 SSTV AUDIO LEVEL ADJUSTMENT

SSC 21.1 SSTV COMPUTER CABLE TXA PLUG (|( SSC EAR (JX TBD) PORT

21.2 (Loudspeaker Icon in the lower left corner (Task Bar) - available

If the icon is not available,

START: Settings: Control Panel

Double Click on Icon Multimedia

The Multimedia dialog box shows

Click to check the SHOW VOLUME ON THE TASK BAR option

Click OK

Close Multimedia dialog box

Repeat 21.2

21.3 Right Button Click on the Loudspeaker Icon and

Select the Properties option.

The Audio Properties dialog box shows (see Figure 4)

[pic]

Figure 4 – Audio Properties Dialog Box

21.4 (Playback option – selected

If not selected,

Click to select

Close the Properties dialog box

21.5 Double click on the Loudspeaker Icon (Task Bar)

The Volume Control dialog box shows

21.6 Adjust the Volume Control Volume slider (leftmost, vertical one) for a comfortable audio level (heard over the SSC internal loudspeaker)

This adjustment can be perfomed while transmitting an image.

(Volume Control Mute option (leftmost) – not selected

Close Volume Control dialog box.

21.7 Right Button Click on the Loudspeaker Icon and

Select the Properties option.

The Audio Properties dialog box shows (see Figure 4)

21.8 Click to select Recording option

Close the Properties dialog box

21.9 Double click on the Loudspeaker Icon (Task Bar)

The Recording Control dialog box shows

21.10 If Line In (Jx TBD) port used,

(Line In Volume level – set to three quarters (up direction)

(Select option – selected

else – Mic (Jx TBD) used

(Microphone Volume level – set to three quarters (up direction)

(Select option – selected

Close Recording Control dialog box.

21.11 SSTV Computer Cable TXA Plug (|( SSC Ear (Jx TBD) port

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download