A NEW APPROACH FOR INTERFACIAL STRESS ANALYSIS OF …



Template for Preparation of PapersJ. Miner1, J. Bond 2, J. Doe 3, J. Smith41 Affiliation name – Country, Email: lead author only 2 Affiliation - Country, 3Affiliation - Country, 4Affiliation - CountryAbstractYour paper should begin with a short abstract that presents a concise statement of the scope, principal findings and conclusions of your work. Abstract should be text only (not contain artwork or references) and is suggested to be 150-250 words in length. 1. IntroductionAbstracts and papers are solicited to report the research and development of new and emerging technologies, new guidelines and innovative approaches to facilitate technology transfer, unique field demonstrations of existing and new technologies, and the development of special programs of general interest. Papers should be relative to one of the topics identified for the conference. Preference will be given to abstracts and papers focused on transferring research into practice.Submissions will be conducted online and include 3 uploads:Abstract - will register your paper title, associated topic, author list and a text only abstract, limited to 250 words maximum. This abstract should give a clear indication of the objective and scope of the paper, key advances of the addressed topics of research and practice, and main findings (if available at the time of submission) so that readers may determine applicability to the SHMII-9 conference. Papers should be related to one of the conference topics.Review Paper – full-length paper that will undergo peer review by the technical committee.Final Paper – updated full-length paper that addresses comments/suggestions by reviewers. This also verifies the document to be used in the proceedings.Official language of conference is English. Papers must be prepared and presented in English using correct grammar and punctuation. The full paper should be written in compliance with these instructions and submitted as a Word (doc or docx) or PDF document via the online submission system. Authors are required to carefully proofread material before submitting. Papers should briefly describe the background and milestone development of the subject, the authors’ work, including the methodologies used, discussion on the importance of the work and concluding remarks. Technical terms should be explained unless they may be considered to be known to the broader scientific community. Terms, acronyms and abbreviations should be mentioned at their first appearance. Proceedings for SHMII-9 will include full-length papers that are fully accepted via technical peer review. Proceedings will be published in an electronic format or hard copy that will be made available to registered attendees. The copyright of all papers will be transferred to the International Society for Structural Health Monitoring of Intelligent Infrastructure (ISHMII). A Copyright Agreement will be required.2. Paper Length and FormatPaper length should be a minimum of 2 pages with maximum not to exceed 6 pages. Authors are recommended to use this template to prepare their papers. This template has been created using “letter” paper size with margins identified.MarginsLetter (8.5 x 11 in.)Top, first page only2.00 , subsequent pages1.00 in.Bottom1.00 in.Left1.00 in.Right1.00 in.All text paragraphs should be typed in single space. Double spacing should be used before and after headings and between paragraphs as shown in this example. 2.1 Page Numbering, Header, Footer Do not insert page numbers. Do not write in headers and footers or change them. 2.2 FontsAuthors should use 12-point Times New Roman font. The text used in figures and tables should not be smaller than 10-point Times New Roman font size.2.3 Tables and FiguresAll figure captions should be typed below the figures and table heads should appear above the tables. Insert figures and tables immediately after they are cited in the text. Figure captions and table headings should clearly explain the figure/table without needing to refer to the text and should be typed with 10-point Times New Roman font. Figures and tables that are not mentioned in the text should not be presented. All figures and tables should be numbered in order of appearance in the text. Figure captions should be centred below the figures and table headings should be centred above the tables.2.4 EquationsEach equation should be presented on a separate line from the text with a blank space above and below. Equations should be clear and expressions used should be explained in the text. The equations should be numbered consecutively at the outer right margin, as shown here below:a + b = c(1)2.5 ConclusionsA “Conclusions” section is required. This section should address all the concluding remarks including introduction, methods, innovations and significance of the research/study and basically review the main points of the paper. Do not replicate the abstract as the conclusions. 2.6 ReferencesAll references should appear together at the end of the paper (see below). References are listed alphabetically by last name of the first author. When two or more references by the same author are listed, year of publication is taken into account, and the earliest work is listed first. Wherever reference is made in the text to an author’s work, the author’s last name(s) and year of publication should appear in parentheses, e.g. Burka (1993), Zhou and Attard (2014), or Dhillon et al (2013). We strongly recommend that superscripts not be used to denote references, as these numbers often appear too small to be read easily. All listed references must be cited in text.Reference Format ExamplesBurka, L. P. (1993). “A hypertext history of multi-user dimensions.” MUD history, <; (Dec. 5, 2013).Committee on Curtain Wall Systems (2014). Curtain Wall Systems: A Primer, ASCE Manuals and Reports on Engineering Practice No. 126. Memari, Ali M., ed. ASCE, Reston, VA. Dhillon, G. S., Surinder K., Ajila C.M., Brar, S. K., Verma, M., Tyagi, R.D., and Surampalli, R. Y. (2013). “Greenhouse Gas Contribution on Climate Change.” Chapter 3 in Climate Change Modeling, Mitigation, and Adaptation, Rao Y. Surampalli, Tian C. Zhang, C.S.P. Ojha, B. Gurjar, R.D. Tyagi, and S.M. Kao, eds. ASCE, Reston, VA, pp. 26-61.Garrett, D. L. (2003). “Coupled analysis of floating production systems.” Proc., Int. Symp. on Deep Mooring Systems, ASCE, Reston, VA, pp. 152-167. Stahl, D. C., Wolfe, R. W., and Begel, M. (2004). “Improved analysis of timber rivet connections.” J. Struct. Eng., 130(8), pp. 1272-1279.Zhou, H. and Attard, T. (2014). "Simplified Anisotropic Plasticity Model for Analyzing the Postyield Behavior of Cold-Formed Sheet-Metal Shear Panel Structures." J. Struct. Eng. , 10.1061/(ASCE)ST.1943-541X.0001152, 04014185. ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download