1.Brief Introduction:



Active RFID Ear Tag ContentBrief IntroductionSystem FunctionsMain ComponentsOperation Instructions1.Brief Introduction:The ear tag is specifically designed with wireless temperature sensor for cattle, cow, sheep or pig etc. to detect the body temperature periodically.The temperature information along with its ID can be sent to the gateway by wireless for the management to well know the health status of the livestock in the office. The tag is low power consumption and the battery life can more than 3 years.Features and application :FCC and CE compliedPerfect integrity of Active RFID technology and sensor technologyLong transmission distanceHigh temperature accuracy: ±0.2?CHigh protection level: IP66.Long battery life: 3 yearsMain Applications:---Temperature measurement---Early detection of health problem--- Cows tracking monitoringThe eye of your farm when you are not looking...Main Applications:EquipmentFunctionTagTemperature data acquisitionRepeaterCollect temperature data from tagReaderTransmit temperature to the PCFunction Descriptionstemperature information and ID code will be sent to the READER via wireless channel. Finally the READER will transmit these data to a PC via USB cable and show it by software on PC. Working process: ReaderTAG1Repeater12Working process:Repe aterRepe aterRepe aterRepe aterRepe aterReaderTAGRepeaterReaderReaderWorking process: 3. Main components Reader/RepeaterTagAccessories:AntennaUSB CableDC Adapter3.1Technical SpecificationsReader/RepeaterFrequency: 433.92MhzReader transmission distance in-line-of-sight: 300 metersRepeater Range in-line-of-sight: 700 metersOperating Voltage? DC 5VPower consumption?Working Currency ≤???A,Sensitivity: –106dbm(Baud rate: 5KHz, frequency deviation: 20KHz)TAGFrequency: 433.92MhzOutput power: 10mWTransmission distance in-line-of-sight: 300 metersOperating Voltage?DC 2.2VTemperature Measurement Range: 0℃ ~ 100℃(32℉~212℉)Temperature Accuracy Range: 03℉/0.2℃(Temperature range is 30℃~45℃.)0.9℉/0.5℃ (Temperature is in other range.)Temperature Resolution: 0.3 ℉ /0.2℃Transmission Interval:10, 15 ,20,mins optionalDescription for each partSignNameDescriptionASMA antenna baseConnect an SMA antennaB1Power LEDWhen the reader’s power is on, the Power LED will be red.B2RX IndicatorIt will flash red when receiving data.B3Not used yetFor future extendingDescription for each partConnectorsNo.NameDescription1USB interfaceConnect to PC2Power supply socketFor DV 5V power supplyThe USB interface format:- BaudRate = 9600 baudWord Length = 8 BitsOne Stop BitNo parityThe output data format in ASCII from USB port of reader: ID+ID number(10 characters)+ : + temperature + F(C) + ?The temperature range is from -10C to 100C(14F-212F),the integer is 3 digit, and the decimal is one digit. If the temperature is lower than 14F, the output is Lo. If the temperature is higher than 212 F, the output is Hi.For example:ID3000000000:081.4F;ID3000000001:HiF;Where 3000000000 is ID number. 081. 4F is temperature value.C 温度探头 头部B 温度探头A 顶部开关按钮C 温度探头 头部B 温度探头D 耳标 耳钉Description for Tag:C:HeadofB: Sensor CableSensor CableA: Power SwitchC:HeadofB: Sensor CableD: Ear TackSensor CableThe front of the TagThe back of the TagPower Button/Switch: Switch on/off and adjust the transmission time intervals.Temperature Sensor/Sensor Cable: The sensor can be inserted intoa?i?al’s ear for dete?ti?g the ?od? te?perature.Head of Sensor Cable: Keep in side of the animal ear, measuring the temperature of the animal.Ear Tack: Fix Tag3. How to install the ear tag: Steps:5. Operating Instructions:Connect the antenna with the reader.Connect the reader with PC by USB Cable and supply power to the readerby DC adapter. The power led will be light.Start PC softwareRepeaterUser should arrange repeater in appropriate position with power supply.When powered on, the red led flash and the repeater start to work.Tag UsageBoot up: Press the top button, you will see the built-in red LED light flashes quickly for 5 times, then it has booted successfully.During the first 5 seconds after LED light stops flashing, you can set up transmitting time interval. When you press the button successfully each time, the red LED light will blink once; after the first 5 seconds, the green LED light blinks in a slow speed, and the number of times it blinks is what you have set the transmitting time interval. That is how you set the transmitting time interval.Press numbers of buttonTransmitting time interval0Testing mode: when first power on, it transmits signal every 10 seconds for 30 times. After that the transmitting time interval turns to 15 minutes115 Minutes210 Minutes3Return to 20 Minutes, recycledAfter step 5, LED light will blink every time it receive signal.Shutdown: Long press the top button, the built-in red LED light will be on for a second, than turn off. TAG now is power off.You can read the operating status via button. The green LED blinks when TAG is working normally, and shows the transmitting time interval at the same time.PC softwareReal time temperature of your cows with unique IDPC softwareWorking 24 hours per dayAlert low temperature (Yellow) and Alert High temperature(Red) is programmable, showing the health information of the cows. ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download